Data Sheet No. PD60107 revU IR2133/IR2135(J&S) & (PbF) IR2233/IR2235(J&S) 3-PHASE BRIDGE DRIVER Features • Floating channel designed for bootstrap operation • • • • • • • • Fully operational to +600V or+1200V Tolerant to negative transient voltage dV/dt immune Gate drive supply range from 10V/12V to 20V DC and up to 25V for transient Undervoltage lockout for all channels Over-current shut down turns off all six drivers Independent 3 half-bridge drivers Matched propagation delay for all channels 2.5V logic compatible Outputs out of phase with inputs Also available LEAD-FREE Product Summary VOFFSET 600V or 1200V max. IO+/- 200 mA / 420 mA VOUT 10 - 20V or 12 - 20V ton/off (typ.) 750/700 ns Deadtime (typ.) 250 ns Packages Description The IR2133IR2135/IR2233IR2355 (J&S) are high voltage, high speed power MOSFET and IGBT driver with three independent 28-Lead SOIC high side and low side referenced output channels for 3-phase 28-Lead PDIP applications. Proprietary HVIC technology enables ruggedized monolithic construction. Logic inputs are compatible with CMOS 44-Lead PLCC w/o 12 leads or LSTTL outputs, down to 2.5V logic. An independent operational amplifier provides an analog feedback of bridge current via an external current sense resistor. A current trip function which terminates all six outputs can also be derived from this resistor. A shutdown function is available to terminate all six outputs. An open drain FAULT signal is provided to indicate that an over-current or undervoltage shutdown has occurred. Fault conditions are cleared with the FLT-CLR lead. The output drivers feature a high pulse current buffer stage designed for minimum driver cross-conduction. Propagation delays are matched to simplify use in high frequency applications. The floating channels can be used to drive N-channel power MOSFETs or IGBTs in the high side configuration which operates up to 600 volts or 1200 volts. Typical Connection up to 600V or 1200V (Refer to Lead Assignments for correct pin configuration). This/These diagram(s) show electrical connections only. Please refer to our Application Notes and DesignTips for proper circuit board layout. www.irf.com 1 IR2133/IR2135/IR2233/IR2235(J&S) & (PbF) Absolute Maximum Ratings Absolute Maximum Ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters are absolute voltages referenced to COM. The Thermal Resistance and Power Dissipation ratings are measured under board mounted and still air conditions. Symbol VB1,2,3 VS1,2,3 VHO1,2,3 VCC VSS VLO1,2,3 VIN VIN,AMP VOUT,AMP VFLT dVS/dt PD RthJA TJ TS TL Definition High side floating supply voltage (IR2133/IR2135) (IR2233/IR2235) High side floating supply offset voltage High side floating output voltage Fixed supply voltage Logic ground Low side output voltage Logic input voltage (HIN, LIN, ITRIP, SD & FLT-CLR) Op amp input voltage (CA+ & CA-) Op amp output voltage (CAO) FAULT output voltage Allowable offset supply voltage transient Package power dissipation @ TA ≤ 25ºC (28 Lead PDIP) (28 Lead SOIC) (44 lead PLCC) Thermal resistance, junction to ambient (28 Lead PDIP) (28 Lead SOIC) (44 lead PLCC) Junction temperature Storage temperature Lead temperature (soldering, 10 seconds Min. Max. -0.3 -0.3 VB1,2,3 - 25 VS1,2,3 - 0.3 -0.3 VCC - 25 -0.3 VSS - 0.3 625 1225 VB1,2,3 + 0.3 VB1,2,3 + 0.3 25 VCC + 0.3 VCC + 0.3 (VSS + 15) or (VCC + 0.3) whichever is lower VCC + 0.3 VCC + 0.3 VCC + 0.3 50 1.5 1.6 2.0 83 78 63 125 150 300 VSS - 0.3 VSS - 0.3 VSS - 0.3 — — — — — — — — -55 — Units V V/ns W ºC/W ºC Recommended Operating Conditions The input/output logic timing diagram is shown in figure 1. For proper operation the device should be used within the recommended conditions. All voltage parameters are absolute voltages referenced to COM. The VS offset rating is tested with all supplies biased at 15V differential. Symbol Parameter Definition VB1,2,3 VS1,2,3 VHO1,2,3 VCC VSS VLO1,2,3 VIN VIN,AMP VOUT,AMP VFLT High side floating supply voltage High side floating supply offset voltage (IR2133/IR2135) (IR2233/IR2235) High side floating output voltage Fixed supply voltage Low side driver return Low side output voltage Logic input voltage (HIN, LIN, ITRIP, SD & FLT-CLR) Op amp input voltage (CA+ & CA-) Op amp output voltage (CAO) FAULT output voltage Min. Max. VS1,2,3 + 10/12 VS1,2,3 + 20 Note 1 600 Note 1 1200 VS1,2,3 VB1,2,3 10 or 12 20 -5 5 0 VCC VSS VSS + 5 VSS VSS + 5 VSS VSS + 5 VSS VCC Units V Note 1: Logic operational for VS of COM - 5V to COM + 600V/1200V. Logic state held for V S of COM -5V to COM -VBS. (Please refer to the Design Tip DT97-3 for more details). Note 2: All input pins, op amp input and output pins are internally clamped with a 5.2V zener diode. 2 www.irf.com IR2133/IR2135/IR2233/IR2235(J&S) & (PbF) Dynamic Electrical Characteristics VBIAS (VCC, VBS1,2,3) = 15V, VS1,2,3 = VSS, TA = 25oC and CL = 1000 pF unless otherwise specified. Symbol Definition Min. Typ. Max. Units Test Conditions ton toff tr tf t sd titrip Turn-on propagation delay Turn-off propagation delay Turn-on rise time Turn-off fall time SD to output shutdown propagation delay ITRIP to output shutdown propagation delay 500 450 — — 500 600 750 700 90 40 750 850 1000 950 150 70 1000 1100 tbl ITRIP blanking time — 400 — t flt ITRIP to FAULT propagation delay 400 650 900 tfil,in Input filter time (HIN, LIN and SD) — 310 — t fltclr FLT-CLR to FAULT clear time 600 850 1100 VIN,VITRIP = 0 & 5V DT Deadtime, LS turn-off to HS turn-on & HS turn-off to LS turn-on Amplifier slew rate (positive) Amplifier slew rate (negative) 100 250 400 VIN = 0 & 5V 5 2 10 2.5 — — SR+ SR- VIN = 0 & 5V VS1,2,3 = 0 to 600V or 1200V ns VIN,VSD = 0 & 5V VIN,VITRIP = 0 & 5V ITRIP = 1V VIN,VITRIP = 0 & 5V VIN = 0 & 5V V/µs NOTE: For high side PWM, HIN pulse width must be ≥ 1µ sec Static Electrical Characteristics VBIAS (VCC, VBS1,2,3) = 15V unless otherwise specified and TA = 25oC. The VIN, VTH and IIN parameters are referenced to VSS and are applicable to all six channels (HS1,2,3 & LS1,2,3). The VO and IO parameters are referenced to VSS and VS1,2,3 and are applicable to the respective output leads: HO1,2,3 or LO1,2,3. Symbol Definition Min. Typ. Max. Units VIH VIL VFCLR,IH VFCLR,IL VSD,TH+ VSD,THVIT,TH+ VIT,THVOH VOL ILK Logic “0” Input Voltage (OUT = LO) Logic “1” Input Voltage (OUT = HI) Logic “0” Fault Clear Input Voltage Logic “1” Fault Clear Input Voltage SD Input Positive Going Threshold SD Input Negative Going Threshold IITRIP Input Positive Going Threshold IITRIP Input Negative Going Threshold High Level Output Voltage, VBIAS - VO Low Level Output Voltage, VO Offset Supply Leakage Current (IR2133/IR2135) (IR2233/IR2235) Quiescent VBS Supply Current Quiescent VCC Supply Current Logic “1” Input Bias Current (OUT = HI) Logic “0” Input Bias Current (OUT = LO) “High” Shutdown Bias Current “Low” Shutdown Bias Current “High” IITRIP Bias Current “Low” IITRIP Bias Current 2.2 — 2.2 — 1.6 1.4 470 360 — — — — — — — — — — — — — — — — 1.9 1.7 570 460 — — — — 50 4 200 100 30 — 30 — IQBS IQCC IIN+ IINISD+ ISDIITRIP+ IITRIPwww.irf.com — 0.8 — 0.8 2.2 2.0 670 560 100 100 50 50 100 8 350 250 100 100 100 100 Test Conditions V mV µA mA µA nA µA nA VIN = 0V, IO = 0A VIN = 5V, IO = 0A VB1,2,3=VS1,2,3 = 600V VB1,2,3=VS1,2,3 = 1200V VIN = 0V or 5V VIN = 0V or 5V VIN = 0V VIN = 5V SD = 5V SD = 0V IITRIP = 5V IITRIP = 0V 3 IR2133/IR2135/IR2233/IR2235(J&S) & (PbF) Static Electrical Characteristics — Continued VBIAS (VCC, VBS1,2,3) = 15V and TA = 25oC unless otherwise specified. The VIN, VTH and IIN parameters are referenced to VSS and are applicable to all six channels (HS1,2,3 & LS1,2,3). The VO and IO parameters are referenced to VSS and VS0,1,2,3 and are applicable to the respective output leads: HO or LO. Symbol Parameter Definition Min. Typ. Max. Units Test Conditions IFLTCLR+ “High” Fault Clear Input Bias Current — 200 350 IFLTCLR- “Low” Fault Clear Input Bias Current — 100 250 VBSUV+ VBSUV- VBSUVH VCCUV+ VCCUV- VCCUVH FLT-CLR = 0V µA FLT-CLR = 5V VBS Supply Undervoltage Positive Going Threshold (for IR2133/IR2233) 7.6 8.6 9.6 (for IR2135/IR2235) 9.2 10.4 11.6 (for IR2133/IR2233) 7.2 8.2 9.2 (for IR2135/IR2235) 8.3 9.4 10.5 (for IR2133/IR2233) — 0.4 — (for IR2135/IR2235) — 1 — (for IR2133/IR2233) 7.6 8.6 9.6 (for IR2135/IR2235) 9.2 10.4 11.6 (for IR2133/IR2233) 7.2 8.2 9.2 (for IR2135/IR2235) 8.3 9.4 10.5 VBS Supply Undervoltage Negative Going Threshold VBS Supply Undervoltage Lockout Hysteresis VCC Supply Undervoltage Positive Going Threshold V VCC Supply Undervoltage Negative Going Threshold VCC Supply Undervoltage Lockout Hysteresis (for IR2133/IR2233) — 0.4 — (for IR2135/IR2235) — 1 — — 70 100 Ω Ron,FLT FAULT- Low On Resistance I O+ Output High Short Circuit Pulsed Current 190 250 — I O- Output Low Short Circuit Pulsed Current 380 500 — VOS Amplifier Input Offset Voltage — 0 30 mV CA+=0.2V, CA-=CAO IIN,AMP Amplifier Input Bias Current — — 4 nA CA+ = CA- = 2.5V CMRR Amplifier Common Mode Rejection Ratio 50 70 — PSRR Amplifier Power Supply Rejection Ratio 50 70 — dB CA+=0.2V, CA-=CAO VCC = 10V & 20V 5 5.2 5.4 V CA+ = 1V, CA- = 0V — — 20 mV CA+ = 0V, CA- = 1V 4 7 — VOH,Amp Amplifier High Level Output Voltage VOL,Amp Amplifier Low Level Output Voltage ISRC,Amp Amplifier Output Source Current ISNK,Amp Amplifier Output Sink Current 0.5 1 — IO+,Amp Amplifier Output High Short Circuit Current — 10 — IO-,Amp Amplifier Output Low Short Circuit Current — 4 — 4 VOUT = 0V, VIN = 0V PW ≤ 10 µs mA VOUT = 15V, VIN = 5V PW ≤ 10 µs CA+ = 0.1V & 5V, CA- = CAO CA+ = 1V, CA- = 0V, CAO = 4V CA+ = 0V, CA- = 1V, CAO = 2V mA CA+ = 5V, CA- = 0V, CAO = 0V CA+ = 0V, CA- = 5V, CAO = 5V www.irf.com IR2133/IR2135/IR2233/IR2235(J&S) & (PbF) Functional Block Diagram Lead Definitions Symbol Lead Description HIN1,2,3 Logic inputs for high side gate driver outputs (HO1,2,3), out of phase. LIN1,2,3 Logic inputs for low side gate driver outputs (LO1,2,3), out of phase. FAULT Indicates over-current or undervoltage lockout (low side) has occurred, negative logic. VCC Logic and low side fixed supply. ITRIP Input for over-current shut down. FLT-CLR Logic input for fault clear, negative logic. SD Logic input for shut down. CAO Output of current amplifier. CA- Negative input of current amplifier. CA+ Positive input of current amplifier. VSS Logic ground. COM Low side return. VB1,2,3 High side floating supplies. HO1,2,3 High side gate drive outputs. VS1,2,3 High side floating supply returns. LO1,2,3 Low side gate drive outputs www.irf.com 5 IR2133/IR2135/IR2233/IR2235(J&S) & (PbF) Lead Assignments ITRIP FAULT ITRIP FAULT FLT-CLR LIN3 FLT-CLR LIN3 CAO LIN2 CAO LIN2 CA- LIN1 CA- LIN1 CA+ HIN3 CA+ HIN3 SD HIN2 SD HIN2 VSS HIN1 VSS HIN1 COM VCC COM VCC LO3 VB1 LO3 VB1 LO2 HO1 LO2 HO1 LO1 VS1 LO1 VS1 VS3 VB2 VS3 VB2 HO3 HO2 HO3 HO2 VB3 VS2 VB3 VS2 28 Lead DIP 44 Lead PLCC w/o 12 Leads IR2133J IR2135J IR2233J IR2235J IR2133 IR2135 IR2233 IR2235 28 Lead SOIC (Wide Body) IR2133S IR2135S IR2233S IR2235S Part Number HIN1,2,3 LIN1,2,3 ITRIP SD FLT-CLR FAULT HO1,2,3 LO1,2,3 Figure 1. Input/Output Timing Diagram 6 www.irf.com IR2133/IR2135/IR2233/IR2235(J&S) & (PbF) HIN LIN 50% 50% t on toff tr 90% HO LO tf 90% 10% 10% Figure 2. Switching Time Waveform Definitions HIN 50% 50% LIN LO 50% 50% HO DT DT Figure 3. Deadtime Waveform Definitions FLT-CLR 50% 50% ITRIP FAULT 50% 50% Any Output 50% t flt t fltclr t itrip Figure 4. Overcurrent Shutdown Waveform www.irf.com 7 IR2133/IR2135/IR2233/IR2235(J&S) & (PbF) HIN/LIN t in,fil on on off off U t in,fil on off high HO/LO low Figure 4.5 Input Filter Function 50% SD tsd 90% HO LO 8 12 0 11 0 10 0 90 80 70 60 50 40 30 20 1E +2 48 0V 32 0V 16 0V 0V 1E +3 1E +4 1E +5 Ju n tio n T e m p e ratu re (°C ) Ju n tion T em p e ratu re (°C ) Figure 5. Shutdown Waveform Definitions 120 110 100 90 80 70 60 50 40 30 20 1E+2 480 320V 160 0V 1E+3 1E+4 1E+5 Frequency (Hz) Frequency (Hz) Figure 7. IR2133J Junction Temperature vs Frequency Driving (IRGPC20KD2) Rgate = 5.1Ω @ Vcc = 15V Figure 8. IR2133J Junction Temperature vs Frequency Driving (IRGPC30KD2) Rgate = 5.1Ω @ Vcc = 15V www.irf.com 1 20 1 10 1 00 90 80 70 60 50 40 30 20 1 E+ 2 4 80 V 3 20 V 1 60 V 0V 1 E+ 3 1 E+ 4 Ju n ctio n T e m p e ratu re (°C ) Ju n ctio n T e m p e ratu re (°C ) IR2133/IR2135/IR2233/IR2235(J&S) & (PbF) 1 E+ 5 150 140 130 120 110 100 90 80 70 60 50 40 30 20 1E+2 480V 320V 160V 0V 1E+3 1E+4 1E+5 Frequency (Hz) Frequency (Hz) Figure 9. IR2133J Junction Temperature vs Frequency Driving (IRGPC40KD2) Rgate = 5.1Ω @ Vcc = 15V Figure 10. IR2133J Junction Temperature vs Frequency Driving (IRGPC50KD2) Rgate = 5.1Ω @ Vcc = 15V 900V 500 300V 0V 1E+3 1E+4 1E+5 Ju n ctio n T e m p e ratu re (°C ) Ju n ctio n T e m p e ratu re (°C ) 900V 120 110 100 90 80 70 60 50 40 30 20 1E+2 1120 1110 1100 90 80 70 60 50 40 30 20 1E+2 500V 300 0V 1E+3 1E+4 1E+5 Frequency (Hz) Frequency (Hz) Figure 11. IR2233J Junction Temperature vs Frequency Driving (IRG4PH30KD) Rgate = 20Ω @ Vcc = 15V Figure 12. IR2233J Junction Temperature vs Frequency Driving (IRG4PH40KD) Rgate = 15Ω @ Vcc = 15V www.irf.com 9 IR2133/IR2135/IR2233/IR2235(J&S) & (PbF) 900V 500V 300V 300V 0V 1E+3 1E+4 1E+5 Ju n ctio n T e m p e ratu re (°C ) Ju n ctio n T e m p e ratu re (°C ) 900V 500V 120 110 100 90 80 70 60 50 40 30 20 1E+2 120 110 100 90 80 70 60 50 40 30 20 1E+2 0V 1E+3 1E+4 1E+5 Frequency (Hz) Frequency (Hz) Figure 13. IR2233J Junction Temperature vs Frequency Driving (IRG4PH50KD) Rgate = 10Ω @ Vcc = 15V Figure 14. IR2233J Junction Temperature vs Frequency Driving (IRG4ZH71KD) Rgate = 5Ω @ Vcc = 15V Package Dimensions 28-Lead PDIP (wide body) 10 01-6011 01-3024 02 (MS-011AB) www.irf.com IR2133/IR2135/IR2233/IR2235(J&S) & (PbF) NOTES 28-Lead SOIC (wide body) 44-Lead PLCC w/o 12 leads www.irf.com 01-6013 01-3040 02 (MS-013AE) 01-6009 00 01-3004 02(mod. ) (MS-018AC) 11 IR2133/IR2135/IR2233/IR2235(J&S) & (PbF) LEADFREE PART MARKING INFORMATION Part number IRxxxxxx YWW? Date code Pin 1 Identifier ? MARKING CODE P Lead Free Released Non-Lead Free Released IR logo ?XXXX Lot Code (Prod mode - 4 digit SPN code) Assembly site code Per SCOP 200-002 ORDER INFORMATION Basic Part (Non-Lead Free) 28-Lead PDIP IR2133 order IR2133 28-Lead SOIC IR2133S order IR2133S 28-Lead PDIP IR2135 order IR2135 28-Lead SOIC IR2135S order IR2135S 28-Lead PDIP IR2233 order IR2233 28-Lead SOIC IR2233S order IR2233S 28-Lead PDIP IR2235 order IR2235 28-Lead SOIC IR2235S order IR2235S 44-Lead PLCC IR2133J order IR2133J 44-Lead PLCC IR2135J order IR2135J 44-Lead PLCC IR2233J order IR2233J 44-Lead PLCC IR2235J order IR2235J Leadfree Part 28-Lead PDIP IR2133 order IR2133PbF 28-Lead SOIC IR2133S order IR2133SPbF 28-Lead PDIP IR2135 order IR2135PbF 28-Lead SOIC IR2135S order IR2135SPbF 28-Lead PDIP IR2233 Not available at this time 28-Lead SOIC IR2233S Not available at this time 28-Lead PDIP IR2235 Not available at this time 28-Lead SOIC IR2235S Not available at this time 44-Lead PLCC IR2133J order IR2133JPbF 44-Lead PLCC IR2135J order IR2135JPbF 44-Lead PLCC IR2233J Not available at this time 44-Lead PLCC IR2235J Not available at this time IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245 Tel: (310) 252-7105 This product has been qualified per industrial level Data and specifications subject to change without notice. 4/12/2004 12 www.irf.com