MCC ER2A THRU ER2M omponents 21201 Itasca Street Chatsworth !"# $ % !"# Features • • • • • 2 Amp Super Fast Recovery Silicon Rectifier 50 to 1000 Volts For Surface Mount Applications Extremely Low Thermal Resistance Easy Pick And Place High Temp Soldering: 250°C for 10 Seconds At Terminals Superfast Recovery Times For High Efficiency Maximum Ratings • • • DO-214AA (SMBJ) (Round Lead) Operating Temperature: -50°C to +150°C Storage Temperature: -50°C to +150°C Maximum Thermal Resistance; 20°C/W Junction To Lead MCC Device Maximum Maximum Maximum Catalog Marking Recurrent RMS DC Number Peak Reverse Voltage Blocking Voltage Voltage ER2A ER2A 50V 35V 50V ER2B ER2B 100V 70V 100V ER2C ER2C 150V 105V 150V ER2D ER2D 200V 140V 200V ER2G ER2G 400V 280V 400V ER2J ER2J 600V 420V 600V ER2K ER2K 800V 560V 800V ER2M ER2M 1000V 700V 1000V H Cathode Band J A E D F ER2A-D ER2G-K ER2M Maximum DC Reverse Current At Rated DC Blocking Voltage Maximum Reverse Recovery Time ER2A-D ER2G-K ER2M Typical Junction Capacitance IF(AV) 2.0A DIMENSIONS TJ = 75°C IFSM 50A 8.3ms, half sine VF .975V 1.35V 1.60V IFM = 2.0A; TJ = 25°C* IR 5µA 150µA TJ = 25°C TJ = 100°C Trr 50ns 60ns 100ns CJ 25pF B G Electrical Characteristics @ 25°C Unless Otherwise Specified Average Forward Current Peak Forward Surge Current Maximum Instantaneous Forward Voltage C DIM A B C D E F G H J INCHES MIN .078 .075 .002 ----.035 .065 .205 .160 .130 MM MIN 1.98 1.90 .05 ----.90 1.65 5.21 4.06 3.30 MAX .116 .089 .008 .02 .055 .091 .224 .180 .155 MAX 2.95 2.25 .20 .51 1.40 2.32 5.69 4.57 3.94 SUGGESTED SOLDER PAD LAYOUT 0.090" 0.085” IF=0.5A, IR=1.0A, Irr=0.25A Measured at 1.0MHz, VR=4.0V *Pulse test: Pulse width 200 µsec, Duty cycle 2% www.mccsemi.com 0.070” NOTE MCC ER2A thru ER2M Figure 1 Typical Forward Characteristics 20 Figure 2 Forward Derating Curve ER2G-2K 10 2.4 6 2.2 ER2A -2D 4 ER2M 2.0 1.8 2 Amps 1.6 1 1.4 1.2 .6 Amps .4 1.0 .8 .2 .6 .4 .1 Single Phase, Half Wave .2 60Hz Resistive or Inductive Load .06 0 .04 0 25 50 75 100 125 150 °C .02 .01 Average Forward Rectified Current - Amperesversus Ambient Temperature - °C .4 .8 1.2 1.6 Volts 2.0 2.4 Instantaneous Forward Current - Amperes versus Instantaneous Forward Voltage - Volts Figure 3 Junction Capacitance 100 60 40 20 pF TJ=25°C 10 6 4 2 1 .1 .2 .4 1 Volts 2 4 10 20 40 100 200 Junction Capacitance - pFversus Reverse Voltage - Volts www.mccsemi.com 400 1000 MCC ER2A thru ER2M Figure 4 Peak Forward Surge Current Figure 5 New SMB Assembly 50 40 30 Amps 20 Round Lead Process 10 0 1 2 4 6 8 10 20 40 60 80 100 Cycles Peak Forward Surge Current - Amperesversus Number Of Cycles At 60Hz - Cycles Figure 6 Reverse Recovery Time Characteristic And Test Circuit Diagram 50Ω 10Ω trr +0.5A 0 Pulse Generator Note 2 25Vdc 1Ω Notes: 1. Rise Time = 7ns max. Input impedance = 1 megohm, 22pF 2. Rise Time = 10ns max. Source impedance = 50 ohms 3. Resistors are non-inductive Oscilloscope Note 1 -0.25 -1.0 1cm Set Time Base for 20/100ns/cm www.mccsemi.com