Order this document by MMFT960T1/D SEMICONDUCTOR TECHNICAL DATA Motorola Preferred Device N–Channel Enhancement–Mode Silicon Gate TMOS SOT–223 for Surface Mount This TMOS medium power field effect transistor is designed for high speed, low loss power switching applications such as switching regulators, dc–dc converters, solenoid and relay drivers. The device is housed in the SOT–223 package which is designed for medium power surface mount applications. • Silicon Gate for Fast Switching Speeds MEDIUM POWER TMOS FET 300 mA 60 VOLTS RDS(on) = 1.7 OHM MAX 4 • RDS(on) = 1.7 Ohm Max 2,4 DRAIN • Low Drive Requirement 2 3 • The SOT–223 Package can be soldered using wave or reflow. The formed leads absorb thermal stress during soldering eliminating the possibility of damage to the die. • Available in 12 mm Tape and Reel Use MMFT960T1 to order the 7 inch/1000 unit reel Use MMFT960T3 to order the 13 inch/4000 unit reel 1 CASE 318E–04, STYLE 3 TO–261AA 1 GATE 3 SOURCE MAXIMUM RATINGS (TC = 25°C unless otherwise noted) Rating Symbol Value Unit Drain–to–Source Voltage VDS 60 Volts Gate–to–Source Voltage — Non–Repetitive VGS ± 30 Volts Drain Current ID 300 mAdc Total Power Dissipation @ TA = 25°C(1) Derate above 25°C PD 0.8 6.4 Watts mW/°C TJ, Tstg – 65 to 150 °C RθJA 156 °C/W TL 260 10 °C Sec Operating and Storage Temperature Range DEVICE MARKING FT960 THERMAL CHARACTERISTICS Thermal Resistance — Junction–to–Ambient Maximum Temperature for Soldering Purposes Time in Solder Bath 1. Device mounted on a FR–4 glass epoxy printed circuit board using minimum recommended footprint. TMOS is a registered trademark of Motorola, Inc. Thermal Clad is a trademark of the Bergquist Company Preferred devices are Motorola recommended choices for future use and best overall value. REV 3 Small–Signal Transistors, FETs and Diodes Device Data Motorola Motorola, Inc. 1997 1 MMFT960T1 ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted) Characteristic Symbol Min Typ Max Unit V(BR)DSS 60 — — Vdc Zero Gate Voltage Drain Current (VDS = 60 V, VGS = 0) IDSS — — 10 µAdc Gate–Body Leakage Current (VGS = 15 Vdc, VDS = 0) IGSS — — 50 nAdc Gate Threshold Voltage (VDS = VGS, ID = 1.0 mAdc) VGS(th) 1.0 — 3.5 Vdc Static Drain–to–Source On–Resistance (VGS = 10 Vdc, ID = 1.0 A) RDS(on) — — 1.7 Ohms Drain–to–Source On–Voltage (VGS = 10 V, ID = 0.5 A) (VGS = 10 V, ID = 1.0 A) VDS(on) — — — — 0.8 1.7 gfs — 600 — mmhos Ciss — 65 — pF Coss — 33 — Crss — 7.0 — Qg — 3.2 — Qgs — 1.2 — Qgd — 2.0 — OFF CHARACTERISTICS Drain–to–Source Breakdown Voltage (VGS = 0, ID = 10 µA) ON CHARACTERISTICS(1) Forward Transconductance (VDS = 25 V, ID = 0.5 A) Vdc DYNAMIC CHARACTERISTICS Input Capacitance (VDS = 25 V, V VGS = 0, 0 f = 1.0 MHz) Output Capacitance Transfer Capacitance Total Gate Charge (VGS = 10 V, V ID = 1.0 1 0 A, A VDS = 48 V) Gate–Source Charge Gate–Drain Charge nC 1. Pulse Test: Pulse Width ≤ 300 µs, Duty Cycle ≤ 2.0%. TYPICAL ELECTRICAL CHARACTERISTICS 5 1 TJ = 25°C 4 I D, DRAIN CURRENT (AMPS) I D, DRAIN CURRENT (AMPS) TJ = 25°C VGS = 10 V 8V 3 7V 2 6V 5V 1 TJ = – 55°C 0.8 TJ = 125°C 0.6 0.4 VDS = 10 V 0.2 4V 0 0 2 4 6 8 VDS, DRAIN–TO–SOURCE VOLTAGE (VOLTS) Figure 1. On–Region Characteristics 2 10 0 0 2 4 6 8 VGS, GATE–TO–SOURCE VOLTAGE (VOLTS) 10 Figure 2. Transfer Characteristics Motorola Small–Signal Transistors, FETs and Diodes Device Data MMFT960T1 5 VGS = 10 V 4 3 TJ = 125°C 2 25°C 1 – 55°C 0 0 0.5 1 1.5 2 ID, DRAIN CURRENT (AMPS) 2.5 RDS(on) , DRAIN–SOURCE RESISTANCE (NORMALIZED) RDS(on) , DRAIN–SOURCE RESISTANCE (OHMS) TYPICAL ELECTRICAL CHARACTERISTICS Figure 3. On–Resistance versus Drain Current 10 ID = 1 A VGS = 10 V 1 0.1 – 75 – 50 – 25 0 25 50 75 100 TJ, JUNCTION TEMPERATURE (°C) 125 150 Figure 4. On–Resistance Variation with Temperature 250 VGS = 0 V f = 1 MHz TJ = 25°C 200 C, CAPACITANCE (pF) I D, DRAIN CURRENT (AMPS) 225 1 TJ = 125°C TJ = 25°C 0.1 175 150 125 100 Ciss 75 Coss 50 Crss 25 0 0 0.3 0.6 0.9 1.2 1.5 VSD, SOURCE–DRAIN DIODE FORWARD VOLTAGE (VOLTS) 0 10 30 2 9 ID = 1 A TJ = 25°C 8 7 6 VDS = 30 V VDS = 48 V 5 4 3 2 1 0 10 15 20 25 VDS, DRAIN–SOURCE VOLTAGE (VOLTS) Figure 6. Capacitance Variation gFS , TRANSCONDUCTANCE (mhos) VGS, GATE–TO–SOURCE VOLTAGE (VOLTS) Figure 5. Source–Drain Diode Forward Voltage 5 0 0.5 1 1.5 2 2.5 3 Qg, TOTAL GATE CHARGE (nC) 3.5 4 Figure 7. Gate Charge versus Gate–to–Source Voltage Motorola Small–Signal Transistors, FETs and Diodes Device Data VDS = 10 V 1.5 1 TJ = – 55°C 25°C 0.5 125°C 0 0 0.5 1 1.5 ID, DRAIN CURRENT (AMPS) 2 2.5 Figure 8. Transconductance 3 MMFT960T1 INFORMATION FOR USING THE SOT-223 SURFACE MOUNT PACKAGE MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS Surface mount board layout is a critical portion of the total design. The footprint for the semiconductor packages must be the correct size to insure proper solder connection interface between the board and the package. With the correct pad geometry, the packages will self align when subjected to a solder reflow process. 0.15 3.8 0.079 2.0 0.091 2.3 0.248 6.3 0.091 2.3 0.079 2.0 0.059 1.5 0.059 1.5 0.059 1.5 inches mm SOT-223 SOT-223 POWER DISSIPATION PD = TJ(max) – TA RθJA 160 Board Material = 0.0625″ G-10/FR-4, 2 oz Copper 140 TA = 25°C 0.8 Watts ° 120 PD = 150°C – 25°C = 0.8 watts 156°C/W The 156°C/W for the SOT-223 package assumes the use of the recommended footprint on a glass epoxy printed circuit board to achieve a power dissipation of 0.8 watts. There are other alternatives to achieving higher power dissipation from the SOT-223 package. One is to increase the area of the collector pad. By increasing the area of the collector pad, the power dissipation can be increased. Although the power 1.25 Watts* 1.5 Watts 100 θ The values for the equation are found in the maximum ratings table on the data sheet. Substituting these values into the equation for an ambient temperature TA of 25°C, one can calculate the power dissipation of the device which in this case is 0.8 watts. 4 dissipation can almost be doubled with this method, area is taken up on the printed circuit board which can defeat the purpose of using surface mount technology. A graph of RθJA versus collector pad area is shown in Figure 9. R JA , Thermal Resistance, Junction to Ambient ( C/W) The power dissipation of the SOT-223 is a function of the pad size. This can vary from the minimum pad size for soldering to a pad size given for maximum power dissipation. Power dissipation for a surface mount device is determined by TJ(max), the maximum rated junction temperature of the die, RθJA, the thermal resistance from the device junction to ambient, and the operating temperature, TA . Using the values provided on the data sheet for the SOT-223 package, PD can be calculated as follows: 80 0.0 *Mounted on the DPAK footprint 0.2 0.4 0.6 A, Area (square inches) 0.8 1.0 Figure 9. Thermal Resistance versus Collector Pad Area for the SOT-223 Package (Typical) Another alternative would be to use a ceramic substrate or an aluminum core board such as Thermal Clad. Using a board material such as Thermal Clad, an aluminum core board, the power dissipation can be doubled using the same footprint. Motorola Small–Signal Transistors, FETs and Diodes Device Data MMFT960T1 SOLDER STENCIL GUIDELINES Prior to placing surface mount components onto a printed circuit board, solder paste must be applied to the pads. A solder stencil is required to screen the optimum amount of solder paste onto the footprint. The stencil is made of brass or stainless steel with a typical thickness of 0.008 inches. The stencil opening size for the SOT-223 package should be the same as the pad size on the printed circuit board, i.e., a 1:1 registration. SOLDERING PRECAUTIONS The melting temperature of solder is higher than the rated temperature of the device. When the entire device is heated to a high temperature, failure to complete soldering within a short time could result in device failure. Therefore, the following items should always be observed in order to minimize the thermal stress to which the devices are subjected. • Always preheat the device. • The delta temperature between the preheat and soldering should be 100°C or less.* • When preheating and soldering, the temperature of the leads and the case must not exceed the maximum temperature ratings as shown on the data sheet. When using infrared heating with the reflow soldering method, the difference should be a maximum of 10°C. • The soldering temperature and time should not exceed 260°C for more than 10 seconds. • When shifting from preheating to soldering, the maximum temperature gradient should be 5°C or less. • After soldering has been completed, the device should be allowed to cool naturally for at least three minutes. Gradual cooling should be used as the use of forced cooling will increase the temperature gradient and result in latent failure due to mechanical stress. • Mechanical stress or shock should not be applied during cooling * Soldering a device without preheating can cause excessive thermal shock and stress which can result in damage to the device. TYPICAL SOLDER HEATING PROFILE For any given circuit board, there will be a group of control settings that will give the desired heat pattern. The operator must set temperatures for several heating zones, and a figure for belt speed. Taken together, these control settings make up a heating “profile” for that particular circuit board. On machines controlled by a computer, the computer remembers these profiles from one operating session to the next. Figure 10 shows a typical heating profile for use when soldering a surface mount device to a printed circuit board. This profile will vary among soldering systems but it is a good starting point. Factors that can affect the profile include the type of soldering system in use, density and types of components on the board, type of solder used, and the type of board or substrate material being used. This profile shows temperature versus time. The line on the graph shows the STEP 1 PREHEAT ZONE 1 “RAMP” 200°C STEP 2 STEP 3 VENT HEATING “SOAK” ZONES 2 & 5 “RAMP” DESIRED CURVE FOR HIGH MASS ASSEMBLIES 150°C actual temperature that might be experienced on the surface of a test board at or near a central solder joint. The two profiles are based on a high density and a low density board. The Vitronics SMD310 convection/infrared reflow soldering system was used to generate this profile. The type of solder used was 62/36/2 Tin Lead Silver with a melting point between 177 –189°C. When this type of furnace is used for solder reflow work, the circuit boards and solder joints tend to heat first. The components on the board are then heated by conduction. The circuit board, because it has a large surface area, absorbs the thermal energy more efficiently, then distributes this energy to the components. Because of this effect, the main body of a component may be up to 30 degrees cooler than the adjacent solder joints. STEP 6 STEP 7 STEP 5 STEP 4 VENT COOLING HEATING HEATING ZONES 3 & 6 ZONES 4 & 7 205° TO “SPIKE” “SOAK” 219°C 170°C PEAK AT SOLDER 160°C JOINT 150°C 100°C 140°C 100°C SOLDER IS LIQUID FOR 40 TO 80 SECONDS (DEPENDING ON MASS OF ASSEMBLY) DESIRED CURVE FOR LOW MASS ASSEMBLIES 50°C TIME (3 TO 7 MINUTES TOTAL) TMAX Figure 10. Typical Solder Heating Profile Motorola Small–Signal Transistors, FETs and Diodes Device Data 5 MMFT960T1 PACKAGE DIMENSIONS A F NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 4 S B 1 2 3 D L G J C 0.08 (0003) M H K CASE 318E–04 ISSUE H TO-261AA INCHES DIM MIN MAX A 0.249 0.263 B 0.130 0.145 C 0.060 0.068 D 0.024 0.035 F 0.115 0.126 G 0.087 0.094 H 0.0008 0.0040 J 0.009 0.014 K 0.060 0.078 L 0.033 0.041 M 0_ 10 _ S 0.264 0.287 STYLE 3: PIN 1. 2. 3. 4. MILLIMETERS MIN MAX 6.30 6.70 3.30 3.70 1.50 1.75 0.60 0.89 2.90 3.20 2.20 2.40 0.020 0.100 0.24 0.35 1.50 2.00 0.85 1.05 0_ 10 _ 6.70 7.30 GATE DRAIN SOURCE DRAIN Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Mfax is a trademark of Motorola, Inc. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 303–675–2140 or 1–800–441–2447 JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 81–3–3521–8315 Mfax: [email protected] – TOUCHTONE 602–244–6609 INTERNET: http://Design–NET.com ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 6 ◊ Motorola Small–Signal Transistors, FETs and Diodes MMFT960T1/D Device Data