Ordering number : ENN6575 Monolithic Linear IC LA9702W DVD Player Front End Processor Overview Package Dimensions The LA9702W is an RF signal-processing and servo error signal generation IC for DVD and CD playback. A DVD player can be implemented by combining this IC with a DVD DSP product that includes a digital servo DSP. unit: mm 3220-SQFP80 [LA9702W] 14.0 Functions and Features 12.0 1.25 0.5 60 0.135 1.25 41 61 0.5 12.0 1.25 40 1.25 14.0 0.2 20 1.4 1 1.6max 21 80 0.1 • RF signal generation (with built-in gain adjustment VGA circuit) • RF peak detection and generation • RF bottom detection and generation (with time constant switching) • Built-in RF equalizer amplifiers (two systems) • FE amplifier (with built-in balance adjustment VCA and offset cancellation pin) • Three-beam TE amplifier (with built-in balance adjustment VCA and offset cancellation pin) • Reflection amplifier • DPD circuit • Tracking hold circuit • Push-pull TE amplifier (with built-in balance adjustment VCA) • Built-in wobble detection bandpass filter • APC circuits (two systems) • Defect detection circuit 0.5 0.5 SANYO: SQFP80 Specifications Maximum Ratings at Ta = 25°C Parameter Maximum supply voltage Allowable power dissipation Symbol Conditions Ratings VCC max Pd max Pdmax for ≤ 70°C (when mounted on a PCB) Unit 6.0 V 500 mW Operating temperature Topr –25 to +70 °C Storage temperature Tstg –40 to +150 °C Note: These specifications are subject to change without notice. Any and all SANYO products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft’s control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO representative nearest you before using any SANYO products described or contained herein in such applications. SANYO assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO products described or contained herein. SANYO Electric Co.,Ltd. Semiconductor Company TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN N2001RM (OT) No. 6575 -1/10 LA9702W Operating Conditions at Ta = 25°C Parameter Symbol Recommended supply voltage Conditions Ratings Vcc Operating supply voltage Vccop Unit 5.0 V 4.5 to 5.5 V Electrical Characteristics/Operating Characteristics at Ta = 25°C, VCC (pins 12, 55, and 66) = 5 V, ground (pins 17, 49, and 74) = 0 V Parameter Current drain Symbol ICC Conditions Ratings min typ max Unit No signal 40 58 75 mA Reference voltage 1 PREF Pin 79, load current: ±2 mA 2.3 2.5 2.7 V Reference voltage 2 SREF Pin 27, load current: ±2 mA 2.3 2.5 2.7 V RF gain 1 RFG1 Input to pins 1 and 2, pin 21 = SREF – 0.75 V Pin 61 = pin 63 = pin 76 = 5 V, pins 40 and 41 0.25 3.25 6.25 dB RF gain 2 RFG2 Input to pins 1 and 2, pin 21 = REF + 0.75 V Pin 61 = pin 63 = pin 76 = 5 V, pins 40 and 41 18 21 24 dB PH PH Pin 7 = pin 8 = pin 9 = 400 mVpp, pin 21 = SREF – 0.75 V SREF + 0.4 Pin 61 = 5 V, pin 63 = pin 76 = 0 V, pin 44 SREF + 0.65 SREF + 0.9 V BH BH Pin 7 = pin 8 = pin 9 = 400 mVpp, pin 21 = SREF – 0.75 V SREF – 0.08 Pin 57 = pin 59 = pin 61 = 5 V, pin 63 = pin 76 = 0 V, pin 42 SREF – 0.28 V SREF – 0.48 RREC1 RREC1 Input to pins 3, 4, 5, and 6, pin 18 = SREF – 0.75 V, pin 76 = 5 V, Pin 28 4.2 9.2 14.2 dB RREC2 RREC2 Input to pins 3, 4, 5, and 6, pin 18 = SREF – 0.75 V, pin 76 = 5 V, Pin 28 20 23 26 dB RRECOST ROST Pin 3 = pin 4 = pin 5 = pin 6 = PREF, pin 18 = SREF Pin 76 = 5 V, pin 28 FEGAIN1 FEG1 Input to pins 3, 4, 5, and 6, pin 18 = SREF – 0.75 V, pin 76 = 5 V, Pin 29 13.9 17.9 21.9 dB FEGAIN2 FEG2 Input to pins 3, 4, 5, and 6, pin 18 = SREF + 0.75 V, pin 76 = 5 V, Pin 29 24 27 30 dB FEOST FOST Pin 3 = pin 4 = pin 5 = pin 6 = PREF, pin 18 = SREF Pin 76 = 5 V, pin 29 FEBAL1 FBAL1 Input such that pin 3 = pin 5 and pin 4 = pin 6, pin 18 = SREF, Pin 76 = 5 V, pin 19 = SREF – 1 V, pin 29: ∆GAIN 3.7 6.7 9.7 dB FEBAL2 FBAL2 Input such that pin 3 = pin 5 and pin 4 = pin 6, pin 18 = SREF, Pin 76 = 5 V, pin 19 = SREF + 1 V, pin 29: ∆GAIN –9.7 –6.7 –3.7 dB TEGAIN1 TEG1 Input to pin 10 and 11, pin 18 = SREF – 0.75 V, pin 63 = 0 V, Pin 68 = 0 V, pin 36 11.8 15.8 19.8 dB TEGAIN2 TEG2 Input to pin 10 and 11, pin 18 = SREF + 0.75 V, pin 63 = 0 V, pin 68 = 0 V, pin 36 26 29 32 dB TEOST TOST Pin 10 = pin 11 = PREF, pin 18 = SREF, pin 63 = 0 V Pin 68 = 0 V, pin 53 = 5 V, pin 36 TEBAL1 TBAL1 Input to pins 10 and 11, pin 18 = SREF, pin 63 = 0 V Pin 68 = 0 V, pin 20 = REF – 1 V, pin 36 ∆GAIN 4 7 10 dB TEBAL2 TBAL2 Input to pins 10 and 11, pin 18 = SREF, pin 63 = 0 V Pin 68 = 0 V, pin 20 = REF + 1 V, pin 36 ∆GAIN –10 –7 –4 dB PD1 The difference in the pin 30 voltage between when input with pin 1 = SREF, pin 2 = 5 MHz with 0° phase, pin 3 = 5 MHz with 36° phase, and when input with pin 1 = SREF, pin 2 = 5 MHz with 36° phase, pin 3 = 5 MHz with 0° phase. RL = 6.8 kΩ 0.25 0.37 0.48 V PD2 The difference in the pin 30 voltage between when input with pin 1 = SREF, pin 2 = 5 MHz with 0° phase, pin 4 = 5 MHz with 36° phase, and when input with pin 1 = SREF, pin 2 = 5 MHz with 36° phase, pin 4 = 5 MHz with 0° phase. RL = 6.8 kΩ –0.48 –0.37 –0.25 V DPD phase difference Voltage difference 1 DPD phase difference Voltage difference 2 SREF – 0.3 SREF – 0.3 SREF – 0.3 SREF SREF + 0.3 SREF SREF + 0.3 SREF SREF + 0.3 V V V Continued on next page. No. 6575 -2/10 LA9702W Continued from preceding page. Parameter DPD phase difference Voltage difference 3 DPD phase difference Voltage difference 4 DPD offset Symbol Conditions Ratings min typ Unit max PD3 The difference in the pin 30 voltage between when input with pin 1 = SREF, pin 2 = 5 MHz with 0° phase, pin 5 = 5 MHz with 36° phase, and input with pin 1 = SREF, pin 2 = 5 MHz with 36° phase, pin 5 = 5 MHz with 0° phase. RL = 6.8 kΩ 0.25 0.37 0.48 V PD4 The difference in the pin 30 voltage between when input with pin 1 = SREF, pin 2 = 5 MHz with 0° phase, pin 6 = 5 MHz with 36° phase, and input with pin 1 = SREF, pin 2 = 5 MHz with 36° phase, pin 6 = 5 MHz with 0° phase. RL = 6.8 kΩ –0.48 –0.37 –0.25 V DPDOF APC1 reference voltage LDS1 Pin 1 = SREF, 2 = 3 = 4 = 5 = 5 MHz, RL = 6.8 kΩ Pin 72 = 5 V SREF – 0.5 150 SREF SREF + 0.5 180 V 200 mV 200 mV APC1 off level LDD1 Pin 72 = 0 V 4.5 5 APC2 reference voltage LDS2 Pin 70 = 5 V 150 180 APC2 off level LDD2 Pin 70 = 0 V 4.5 5 1.8 4 5.8 µS 100 500 µS DFFTMU Pin 2 = 80 kHz. The time difference from a pin 2 edge to DEFTMU the rising edge on pin 46. DFFTMD DFFTMD Pin 2 = 80 kHz. The time difference from a pin 2 edge to the falling edge on pin 46. V V BPF1 BPF1 Pin 34 = 210 kHz, pin 32 –1 2 5 dB BPF2 BPF2 Pin 34 = 120 kHz, pin 32 –20 –4 0 dB BPF3 BPF3 Pin 34 = 3500 kHz, pin 32 –20 –6.5 –1 dB No. 6575 -3/10 LA9702W Functional Description 1. RF amplifier • DVD mode The RF signal input as a differential signal to pins 1 and 2 is passed through the RF VCA and is output from pin 65. The signal output from pin 65 is passed through a DVD RF equalizer and is output to later stage ICs from pins 40 and 41. When pin 63 is high, the RF signal does not pass through the customer amplifier. As a result, it is not influenced by the external peripheral circuit connected to pins 78 through 80. The RF VCA gain is controlled by applying a DC voltage to pin 21. This IC provides two RF equalizer systems, and when pin 61 is high the pin 77 equalizer output is selected, and when low, the pin 52 equalizer output is selected. The amount of boost provided by the RF equalizer can be modified with the pin 22 DC voltage. • CD mode Pins 8, 9, and 10 can be set to be the RF input pins by setting pin 76 low. The customer amplifier connected to pins 78 through 80 is enabled by setting pin 63 low, a CD equalizer circuit can be constructed on pins 78 through 80, and the signal will not pass through the DVD RF equalizer. The RF VCA gain is controlled by applying a DC voltage to pin 21. 2. Peak hold/bottom hold The envelope waveforms for the peak and bottom of the front end RF signal output from pins 40 and 41 are output from pins 42 and 43. The envelope detection constants are set by the values of the resistors inserted between pins 43 and 39 and ground. The bottom hold detection constant can be increased by about a factor of 4 by setting pin 59 low. The bottom hold band width is also be increased by about a factor of 2 by setting pin 57 low. 3. Defect detection The RF signal input from the pickup is converted to binary by a limiter circuit. The binary signal time is observed with a monostable multivibrator, and if there is no change in binary signal for over a certain fixed period, pin 46 is set high. The time period of the monostable multivibrator is set by the value of the capacitor connected to pin 47 and the resistor connected to pin 48. 4. RF equalizer The CD RF equalizer is constructed from external components and the customer amplifier on pins 78 and 80, and outputs to the RF VCA in the next stage. This IC provides two DVD RF equalizer systems, one of which is formed from external components and pins 67, 69, 71, 73, 75, and 77, and the other system is formed from external components and pins 52, 54, 56, 58, 60, and 62. When pin 61 is high, the equalizer system on pins 67, 69, 71, 73, 75, and 77 is selected, and when that pin is low, the equalizer system on pins 52, 54, 56, 58, 60, and 62 is selected. Since the customer amplifier is excluded from the signal path when pin 63 is high, the CD equalizer does not influence IC operation in DVD mode. 5. BCA Peak envelope detection is applied to the previous stage RF signal output from pins 40 and 41. The result is converted to binary by comparison with the BCA threshold and output from pin 45. The BCA threshold is input from external circuits to pin 25. 6. Reflect amplifier The signals input to pins 3, 4, 5, and 6 or pins 7, 8, and 9 are added with an summing amplifier. The pit component is removed from the input signal with a low-pass filter. The summed signal is passed through a VCA that adjusts the servo gain and output from pin 28. The VCA that adjusts the servo gain is controlled by the DC voltage applied to pin 18. Note that when the pin 76 input is high, pins 3, 4, 5, and 6 are selected, and when low, pins 7, 8, and 9 are selected. No. 6575 -4/10 LA9702W 7. FE amplifier The signal input from either pins 3, 4, 5, and 6 or pins 8 and 9 is first passed through an offset adjustment circuit and is then passed through a balance adjustment VCA. Then either the calculation <(pin 3 + pin 5) – (pin 4 + pin 6)> or <pin 8 – pin 9> is performed. The result is passed through the servo gain adjustment VCA and output from pin 29. The gain of the balance adjustment VCA is adjusted by the DC voltage input to pin 19. The offset adjustment can be adjusted by the DC voltage applied to pin 23. The VCA that adjusts the servo gain is controlled by the DC voltage applied to pin 18. Note that when the pin 76 input is high, pins 3, 4, 5, and 6 are selected, and when low, pins 8 and 9 are selected. 8. TE amplifier (for three-beam operation) The current signal input to pin 10 and 11 is converted from a current to a voltage, passed through an offset adjustment circuit, and passed through a balance adjustment VCA. Then the calculation <pin 11 – pin 10> is performed and the result passed through a servo gain adjustment VCA. The result is output from pin 30 after band switching. The offset adjustment can be adjusted by the DC voltage applied to pin 24. The gain of the balance adjustment VCA can be adjusted by the DC voltage applied to pin 20. The VCA that adjusts the servo gain is controlled by the DC voltage applied to pin 18. The band switching circuit is a low-pass filter with a cutoff frequency of 30 kHz when pin 57 is high and 100 kHz when pin 57 is low. When pin 53 is low, pin 30 operates in hold mode. Note that the three-beam TE is used when pin 68 is low. 9. DPD circuit The phases of the signals input to pins 1 and 2, and the signals input to pins 3, 4, 5, and 6 are compared and the result outputs from pin 30. The phase comparison result signal is output as a current by the pin 38 constant-current charge pump and converted to a voltage level by the external capacitor and resistor on pin 38. The voltage-converted signal is passed through a buffer amplifier, is band limited by a band switching circuit, and is output from pin 30. The charge pump is turned off when pin 51 is high. The band switching circuit is a low-pass filter with a cutoff frequency of 30 kHz when pin 57 is high and 100 kHz when pin 57 is low. When pin 53 is low, pin 30 operates in hold mode. Note that the DPD circuit is used when pin 63 will be high. 10. PP amplifier The signals input to pins 3, 4, 5, and 6 are passed first through an offset adjustment circuit and then through a balance adjustment VCA. The calculation <(pin 3 + pin 6) – (pin 4 – pin 5)> is performed. The result is passed through a servo gain adjustment VCA and is output from pin 35 after band switching. The offset adjustment can be adjusted by the DC voltage applied to pin 24. The gain of the balance adjustment VCA can be adjusted by the DC voltage applied to pin 20. The VCA that adjusts the servo gain is controlled by the DC voltage applied to pin 18. Note that the PP amplifier is used when pin 68 will be high. 11. Wobble bandpass filter The signal input to pin 34 is passed through a bandpass filter and output from pin 32. The frequency fo for the bandpass filter can be modified with the external resistor on pin 33. When the pin 33 external resistor is 62 kΩ, fo will be about 200 kHz. 12. APC circuit A servo loop that holds the laser power fixed can be formed by inputting a monitor signal to pin 14 and connecting the laser driver to pin 13. The laser can be turned off by setting pin 72 low. Note that there are two APC systems, with the other system consisting of pin 16 as the monitor input pin, pin 15 as the drive pin, and pin 70 as the laser off control pin. 13. Reference circuit A voltage that is created by resistor dividing VCC by 2 is output from pin 26. The pin 26 voltage is buffered and output from pins 79 and 27. The pin 79 voltage is a special-purpose reference voltage only for use by the pickup, and the pin 27 voltage is a reference supplied to the DSP and other systems. No. 6575 -5/10 LA9702W Pin Functions Pin No. Pin 1 RFN RF signal – input Function 2 RFP RF signal + input 3 PD1 Pickup signal input 4 PD2 Pickup signal input 5 PD3 Pickup signal input 6 PD4 Pickup signal input 7 PD5 Pickup signal input 8 PD6 Pickup signal input 9 PD7 Pickup signal input 10 PD8 Pickup signal input 11 PD9 Pickup signal input 12 VCC Power supply (servo signal system) 13 LDD1 APC 1 output 14 LDS1 APC 1 monitor voltage input 15 LDD2 APC 2 output 16 LDS2 APC 2 monitor voltage input 17 GND Ground (servo signal system) 18 SGC Servo gain control (RREC, FE, and TE) 19 FEBL Focus balance adjustment 20 TEBL Tracking balance adjustment 21 VGA RF gain adjustment 22 BST Equalizer boost adjustment 23 FOST Focus offset adjustment 24 TOST Tracking offset adjustment 25 BCATH BCA threshold adjustment 26 REFI Reference voltage setting 27 SREF Servo signal reference voltage output 28 RREC Reflection output 29 FE Focus error output 30 TE Tracking error output 31 THC TE hold time constant setting capacitor connection 32 WO Wobble output 33 ISET Bandpass filter center frequency setting resistor connection 34 WOI Push-pull signal input Push-pull signal output 35 WOO 36 TEO Three-beam TE gain setting 37 TEN Three-beam TE gain setting 38 CP Charge pump gain setting resistor and capacitor connection 39 BHI Bottom hold detection constant setting resistor connection 40 RFON RF – output 41 RFOP RF + output 42 BH RF bottom detection output 43 PHI Peak hold detection constant setting resistor connection 44 PH 45 BCA BCA output Defect output (High: defect detected) 46 DEF 47 DEFC 48 TC RF peak detection output Defect detection capacitor connection Defect detection constant setting resistor connection 49 GND Ground (DPD system) 50 LPC RF DC servo capacitor connection 51 CPOF Charge pump on/off control (High: off) 52 EQO2 RF equalizer setting 53 TH Tracking hold (High: hold) Continued on next page. No. 6575 -6/10 LA9702W Continued from preceding page. Pin No. Pin 54 EQL2 RF equalizer setting Function 55 VCC Power supply (DPD system) 56 EQO4 57 XHTR Tracking and bottom detection band switching (Low: high band) 58 EQI4 RF equalizer setting 59 XQBH Bottom detection time constant switching (Low: fast) 60 EQ03 RF equalizer setting 61 EQSCT 62 EQI3 63 DPD/TE 64 RFO2 RF output 65 RFO1 RF output 66 VCC Power supply (RF system) 67 EQI1 RF equalizer setting 68 PP/TE Three-beam/push-pull tracking switching (Low: three-beam) 69 EQO1 RF equalizer setting 70 LDON2 APC 2 laser on/off control (High: on) 71 EQI2 72 LDON1 APC 1 laser on/off control (High: on) 73 EQO2 RF equalizer setting 74 GND Ground (RF system) 75 EQL1 76 RFSCT RF input switching (High: RF differential input, PP error) RF equalizer setting RF equalizer setting Equalizer switching (High: pin 77 selected, low: pin 52 selected) RF equalizer setting DPD/three-beam tracking switching (High: DPD) RF equalizer setting RF equalizer setting 77 EQO1 78 CAO Customer amplifier output 79 PREF Reference voltage output (pickup) 80 CAN Customer amplifier input Note: The equalizer constants support 1× and 2× speeds. No. 6575-7/10 LA9702W Test Circuit No. 6575-8/10 LA9702W Sample Application Circuit The equalizer constants support normal and 2× speeds. No. 6575-9/10 LA9702W Specifications of any and all SANYO products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer’s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer’s products or equipment. SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO products (including technical data, services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Electric Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the “Delivery Specification” for the SANYO product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of November, 2001. Specifications and information herein are subject to change without notice. PS No. 6575 -10/10