Pressure Freescale Semiconductor MPXV5050VC6T1 Rev 2, 11/2009 High Temperature Accuracy Integrated Silicon Pressure Sensor for Measuring Absolute Pressure, On-Chip Signal Conditioned, Temperature Compensated and Calibrated MPXV5050V Series -50 to 0 kPa (-7.25 to 0 psi) 0.1 to 4.6 V Output The MPXV5050V series sensor integrates on-chip, bipolar op amp circuitry and thin film resistor networks to provide a high output signal and temperature compensation. The small form factor and high reliability of on-chip integration make the Freescale Semiconductor, Inc. pressure sensor a logical and economical choice for the system designer. The MPXV5050V series piezoresistive transducer is a state-of-the-art, monolithic, signal conditioned, silicon pressure sensor. This sensor combines advanced micromachining techniques, thin film metallization, and bipolar semiconductor processing to provide an accurate, high level analog output signal that is proportional to applied pressure. Application Examples • Vacuum Pump Monitoring Features • • • • • • • 2.5% Maximum Error over 0° to 85°C Ideally suited for Microprocessor or Microcontroller-Based Systems Temperature Compensated from Over -40° to +125°C Patented Silicon Shear Stress Strain Gauge Durable Thermoplastic (PPS) Surface Mount Package Easy-to-Use Chip Carrier Option Ideal for Automotive and Non-Automotive Applications ORDERING INFORMATION Device Name Case No. # of Ports None Single Pressure Type Dual Gauge Differential Absolute Device Marking Small Outline Package MPXV5050VC6T1 482A • • Vacuum/Gauge SMALL OUTLINE PACKAGE MPXV5050VC6T1 CASE 482A-01 © Freescale Semiconductor, Inc., 2005, 2009. All rights reserved. MPXV5050V Pressure Operating Characteristics Table 1. Operating Characteristics (VS = 5.0 Vdc, TA = 25°C unless otherwise noted, P1 > P2) Characteristic Symbol Min Typ Max Unit Pressure Range POP -50 — 0 kPa Supply Voltage(1) VS 4.75 5.0 5.25 Vdc Supply Current Io — 7.0 10 mAdc Full Scale Output(2) @ VS = 5.0 Volts (0 to 85°C) VFSO 4.488 4.6 4.713 Vdc Full Scale Span(3) @ VS = 5.0 Volts (0 to 85°C) VFSS — 4.5 — Vdc Accuracy(4) (0 to 85°C) — — — ±2.5 %VFSS Sensitivity V/P — 90 — mV/kPa (5) tR — 1.0 — ms Warm-Up Time(6) — — 20 — ms Offset Stability(7) — — ±0.5 — %VFSS Voff 0 0.100 0.213 Vdc Response Time Pressure Offset(8) (0 to 85°C) 1. Device is ratiometric within this specified excitation range. 2. Full Scale Output (VFSO) is defined as the output voltage at the maximum or full rated pressure. 3. Full Scale Span (VFSS) is defined as the algebraic difference between the output voltage at full rated pressure and the output voltage at the minimum rated pressure. 4. Accuracy is the deviation in actual output from nominal output over the entire pressure range and temperature range as a percent of span at 25°C due to all sources of error including the following: Linearity: Output deviation from a straight line relationship with pressure over the specified pressure range. Temperature Hysteresis: Output deviation at any temperature within the operating temperature range, after the temperature is cycled to and from the minimum or maximum operating temperature points, with zero differential pressure applied. Pressure Hysteresis: Output deviation at any pressure within the specified range, when this pressure is cycled to and from minimum or maximum rated pressure at 25°C. TcSpan: Output deviation over the temperature range of 0° to 85°C, relative to 25°C. TcOffset: Output deviation with minimum pressure applied, over the temperature range of 0° to 85°C, relative to 25°C. 5. Response Time is defined as the time for the incremental change in the output to go from 10% to 90% of its final value when subjected to a specified step change in pressure. 6. Warm-up Time is defined as the time required for the product to meet the specified output voltage after the pressure has been stabilized. 7. Offset Stability is the product's output deviation when subjected to 1000 cycles of Pulsed Pressure, Temperature Cycling with Bias Test. 8. Offset (Voff) is defined as the output voltage at the minimum rated pressure. MPXV5050VC6T1 2 Sensors Freescale Semiconductor Pressure Maximum Ratings Table 2. Maximum Ratings(1) Rating Symbol Value Units Maximum Pressure (P1 > P2) Pmax 200 kPa Storage Temperature Tstg -40 to +125 °C Operating Temperature TA -40 to +125 °C 1. Exposure beyond the specified limits may cause permanent damage or degradation to the device. Figure 1 shows a block diagram of the internal circuitry integrated on a pressure sensor chip. VS 2 Thin Film Temperature Compensation And Gain Stage #1 Sensing Element GND 3 Gain Stage #2 And Ground Reference Shift Circuitry 4 Vout Pins 1, 5, 6, 7, and 8 are no connects Figure 1. Fully Integrated Pressure Sensor Schematic MPXV5050VC6T1 Sensors Freescale Semiconductor 3 Pressure On-chip Temperature Compensation and Calibration Figure 2 illustrates the absolute sensing chip in the basic Super Small Outline chip carrier (Case 482A). Figure 3 shows a typical application circuit (output source current operation). Figure 4 shows the sensor output signal relative to pressure input. Typical minimum and maximum output curves are shown for operation over 0° to 85°C temperature range. The output will saturate outside of the rated pressure range. Fluorosilicone Gel Die Coat Die A fluorosilicone gel isolates the die surface and wire bonds from the environment, while allowing the pressure signal to be transmitted to the silicon diaphragm. The MPXV5050 series pressure sensor operating characteristics, internal reliability and qualification tests are based on use of dry air as the pressure media. Media other than dry air may have adverse effects on sensor performance and long-term reliability. Contact the factory for information regarding media compatibility in your application. +5 V Stainless Steel Cap P1 Wire Bond OUTPUT Vout Thermoplastic Case Vs IPS Lead Frame 1.0 μF P2 0.01 μF GND 470 pF Die Bond Differential Sensing Element Figure 2. Cross Sectional Diagram SSOP (not to scale) Figure 3. Typical Application Circuit (Output Source Current Operation) Transfer Function MPXV5050VC Series 5 3 Span Range (Typ) Output Voltage (V) 4 TYPICAL MAX 2 Output Range (Typ) Transfer Function: Vout = VS x (0.018 x P + 0.92) ± (PE x TM x 0.018 x Vs) Vs = 5.0 ± 0.25 vdc PE = 1.25 TM = 1 Temperature = 0 to 85°C MIN 1 0 –50 –40 –30 –20 –10 Pressure (kPa) 0 Offset (Typ) Figure 4. Output vs. Absolute Pressure MPXV5050VC6T1 4 Sensors Freescale Semiconductor Pressure Transfer Function (MPXV5050V) Nominal Transfer Value: VOUT = VS x (0.018 x P + 0.92) ± (Pressure Error x Temp Multi x 0.018 x VS) VS = 5.0 ± 0.25 V Temperature Error Band MPXV5050V 4.0 Break Points Temp 3.0 Temperature Error Factor Multiplier –40 0 to 85 +125 2.0 3 1 3 1.0 0.0 –40 –20 0 20 40 60 80 100 120 140 Temperature in °C NOTE: The Temperature Multiplier is a linear response from 0°C to –40°C and from 85°C to 125°C. Pressure Error Band MPXV5050V Error Limits for Pressure Pressure Error (kPa) 1.25 1.00 0.75 0 –50 –40 –30 –20 –10 0 Pressure (in kPa) –0.75 –1.00 –1.25 Pressure Error (Max) –50 to 0 kPa ±1.25 kPa MPXV5050VC6T1 Sensors Freescale Semiconductor 5 Pressure SURFACE MOUNTING INFORMATION MINIMUM RECOMMENDED FOOTPRINT FOR SMALL OUTLINE PACKAGE Surface mount board layout is a critical portion of the total design. The footprint for the semiconductor package must be the correct size to ensure proper solder connection interface between the board and the package. With the correct pad geometry, the packages will self-align when subjected to a solder reflow process. It is always recommended to fabricate boards with a solder mask layer to avoid bridging and/or shorting between solder pads, especially on tight tolerances and/or tight layouts. 0.100 TYP 2.54 0.660 16.76 0.060 TYP 8X 1.52 0.300 7.62 0.100 TYP 8X 2.54 inch mm Figure 5. SOP Footprint (Case 482A) MPXV5050VC6T1 6 Sensors Freescale Semiconductor Pressure PACKAGE DIMENSIONS -A- D 4 0.25 (0.010) 5 N 8 PL M T B S A S NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006). 5. ALL VERTICAL SURFACES 5˚ TYPICAL DRAFT. -BG 8 1 S W V C H J -TK M PIN 1 IDENTIFIER DIM A B C D G H J K M N S V W INCHES MIN MAX 0.415 0.425 0.415 0.425 0.500 0.520 0.038 0.042 0.100 BSC 0.002 0.010 0.009 0.011 0.061 0.071 0˚ 7˚ 0.444 0.448 0.709 0.725 0.245 0.255 0.115 0.125 MILLIMETERS MIN MAX 10.54 10.79 10.54 10.79 12.70 13.21 0.96 1.07 2.54 BSC 0.05 0.25 0.23 0.28 1.55 1.80 0˚ 7˚ 11.28 11.38 18.01 18.41 6.22 6.48 2.92 3.17 SEATING PLANE CASE 482A-01 ISSUE A SMALL OUTLINE PACKAGE MPXV5050VC6T1 Sensors Freescale Semiconductor 7 How to Reach Us: Home Page: www.freescale.com Web Support: http://www.freescale.com/support USA/Europe or Locations Not Listed: Freescale Semiconductor, Inc. Technical Information Center, EL516 2100 East Elliot Road Tempe, Arizona 85284 1-800-521-6274 or +1-480-768-2130 www.freescale.com/support Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) www.freescale.com/support Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku, Tokyo 153-0064 Japan 0120 191014 or +81 3 5437 9125 [email protected] Asia/Pacific: Freescale Semiconductor China Ltd. Exchange Building 23F No. 118 Jianguo Road Chaoyang District Beijing 100022 China +86 010 5879 8000 [email protected] For Literature Requests Only: Freescale Semiconductor Literature Distribution Center 1-800-441-2447 or +1-303-675-2140 Fax: +1-303-675-2150 [email protected] MPXV5050VC6T1 Rev. 2 11/2009 Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”, must be validated for each customer application by customer’s technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. © Freescale Semiconductor, Inc. 2009. All rights reserved.