FTR-K1 SERIES POWER RELAY 2 POLE - 5A - 1.5mm contact gap FTR-F4G Series n FEATURES 2 Pole, 5A 2 Form A l Contact gap 1.5mm l Sealed l High insulation in small package (between coil and contact) - Insulation distance: min 8.0mm - Dielectric strength: 5,000VAC - Surge strength: 10,000V l Flammability UL94V-0 (plastics) l RoHS compliant Features cadmium-free contacts Please see page 5 for more information l l n PARTNUMBER INFORMATION [Example] FTR-F4G A K 012 T (a) (b) (c) (d) (e) (a) Relay type FTR-F4G: FTR-F4G Series (b) Contact configuration A : 2 form A (c) (d) Coil type K : Standard (0.8W) Coil rated voltage 012 : 5.....48 VDC Coil rating table at page 3 (e) Contact rating T : TV rating Actual marking does not carry the type name : "FTR" E.g.: Ordering code: FTR-F4GAK012T Actual marking: F4GAK012T FTR-F4G FTR-K1SERIES SERIES n SPECIFICATION Item Contact Data Life Coil Data Timing Data Insulation FTR-F4G Configuration 2 form A Material Silver tin oxide Resistance (initial) ≤ 100mOhm at 1A, 6VDC Contact rating 5A, 250VAC (resistive) Max. carrying current 5A Max. switching current 5A Max. switching voltage 400VAC Max. switching power 1,250VA Min. switching load (reference) 100 mA, 5VDC Mechanical 500 x 103 operations minimum Electrical (resistive) 100 x 103 operations minimum Rated power (at 20 °C) Approximately 0.8W Operate power (at 20 °C) Approximately 0.45W Operating temperature range -40 °C to +70 °C (no frost) Operate (at nominal voltage) ≤ 12ms (no bounce) Release * ≤ 5ms (no diode) Contact gap (initial) Minimum 1.5mm Resistance (initial) ≥ 1,000MOhm at 500VDC Dielectric strength Surge strength Other Vibration resistance Shock resistance Weight Open contacts 1,000VAC, 1min. Contacts sets 3,000VAC, 1min. Coil and contacts 5,000VAC, 1min. Coil to contacts 10,000V / 1.2 x 50µs standard wave Misoperation 10 to 55Hz double amplitude 1.5 mm Endurance 10 to 55Hz double amplitude 1.5 mm Misoperation Min. 100m/s² (11 ± 1ms) Endurance Min. 1,000m/s² (6 ± 1ms) Approximately 18 g *Use a varistor as a protective circuit against reverse surge in the relay coil. A varistor is connected parallel to the coil. The reverse blocking voltage should be about 3 times the value of the power surge voltage. FTR-K1SERIES SERIES FTR-F4G n COIL RATING Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Must Operate Voltage (VDC) * Must ReleaseVoltage (VDC) * 005 5 31 3.75 0.25 012 12 180 9 0.6 024 24 720 18 1.2 048 48 2,880 36 2.4 Rated Power +/- 10% (W) Approx. 0.8 Note: All values in the table are measured at 20°C and zero contact current. * Specified values are measured with pulse wave voltage n SAFETY STANDARDS Type Compliance Contact rating UL UL 508 5A, 277VAC, resistive TV-3, 125VAC VDE 0435 5A, 250VAC (cosφ=1) 70°C FTR-K1SERIES SERIES FTR-F4G n DIMENSIONS l Dimensions l Schematics (BOTTOM VIEW) l PC board pattern (BOTTOM VIEW) Unit: mm FTR-K1SERIES SERIES FTR-F4G RoHS Compliance and Lead Free Information 1. General Information All signal and power relays produced by Fujitsu Components are compliant with RoHS directive 2002/95EC including amendments. l Cadmium as used in electrical contacts is exempted from the RoHS directives on October 21st, 2005. (Amendment to Directive 2002/95/EC) l All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf l Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. l 2. Recommended Lead Free Solder Profile Recommended solder Sn-3.0Ag-0.5Cu. l Flow Solder condition: Pre-heating: Soldering: maximum 120˚C dip within 5 sec. at 260˚C solder bath Solder by Soldering Iron: Soldering Iron Temperature: maximum 360˚C Duration: maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. l 4. Tin Whiskers Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. l FTR-K1SERIES SERIES FTR-F4G Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: [email protected] Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: [email protected] Web: emea.fujitsu.com/components/ North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: [email protected] Web: http://us.fujitsu.com/components Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: [email protected] Web: http://www.fujitsu.com/sg/services/micro/components/ ©2009 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users’ own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. October 15, 2009