FTR-K1 SERIES POWER RELAY 1 POLE - 16A Sealed Type FTR-K1 Series n FEATURES 1 pole 16A l 1 form A / 1 form C l Coil sensitive 400mW l High insulation in small package (between coil and contacts) - Insulation distance: 10mm min. - Dielectric strength: 5,000VAC - Surge strength: 10,000V l Conform to UL1446 Class F coil insulation system l Cadmium free contacts l RoHS compliant Please see page 7 for more information l l n PARTNUMBER INFORMATION FTR-K1 C K 005 W - KW [Example] (a) (b) (c) (d) (e) (f) (a) Relay type FTR-K1: FTR-K1 Series (b) Contact configuration A C : 1 form A : 1 form C (c) Coil type K : Standard type (400mW) / flux free (d) Coil rated voltage 005 : 5.....48 VDC Coil rating table at page 3 (e) Contact material W : AgSnO2 (f) Special type KW : Sealed type Actual marking does not carry the type name : "FTR" E.g.: Ordering code: FTR-K1CK005W-KW Actual marking: K1CK005W-KW 1 FTR-K1SERIES SERIES FTR-K1 n SPECIFICATION 16A type Item Contact Data FTR-K1 CK ( ) W-KW Configuration 1 form C Construction Single Material AgSnO2 Resistance (initial) Maximum 100mΩ at 1A, 6VDC Contact rating (resistive) Max. carrying current Coil Data Timing Data Insulation 440VAC 4,000VA *2 100mA, 5VDC 20 x 106 operations minimum Mechanical Rating resistive load 10 x 103 operations minimum 20 x 103 operations minimum Rated power (20 °C) 400 / 430 mW Operating temperature range -40 °C to +85 °C (no frost) Operate (at nominal voltage) ≤ 15ms (no bounce, no diode) Release (at nominal voltage) ≤ 5ms (no bounce, no diode) Resistance (initial) ≥ 1,000MOhm at 500VDC Dielectric strength Surge strength Open contacts 1,000VAC (50/60Hz) 1min Contacts to coil 5,000VAC (50/60Hz) 1min Coil to contacts 10,000V / 1.2 x 50µs standard wave Clearance 10mm Creepage 10mm EN61810-1, VDE0435 Other 20A Max. switching power Electrical 1 form A 16A, 250VAC *1 Max. switching voltage Min. switching load Life FTR-K1 AK ( ) W-KW Vibration resistance Shock Weight Voltage 250 Pollution degree 3 Material group III a Category C / 250V Misoperation≥1us 10 to 55Hz double amplitude 0.7mm Endurance 10 to 55Hz double amplitude 1.5mm Misoperation≥1us 100m/s² (11 ± 1ms) Endurance 1,000m/s² (6 ± 1ms) Approximately 13g * 1: Need to consider the heat from PCB when max. current is more than 10A. * 2: Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. 2 FTR-K1 FTR-K1SERIES SERIES n COIL RATING Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Must Operate Voltage (VDC) * Must ReleaseMax. Coil Voltage Voltage (VDC) (VDC) * 005 5 62 3.5 0.5 12.2 006 6 90 4.2 0.6 14.7 009 9 202 6.3 0.9 22.0 012 12 360 8.4 1.2 29.4 018 18 810 12.6 1.8 44.1 022 22 1210 15.4 2.2 53.9 024 24 1440 16.8 2.4 58.8 028 28 1960 19.6 2.8 68.6 048 48 5360 33.6 4.8 117.6 Rated Power (mW) 400 430 Note: All values in the table are valid for 20°C and zero contact current. * Specified operate values are valid for pulse wave voltage. n SAFETY STANDARDS Type Compliance Contact rating UL 508 E 63614 Flammability: UL 94-VII (plastics) 0435; 40013848 16A, 250VAC cos Ø=1 85 °C 10.000 ops. VDE UL-94-V0 3 FTR-K1 FTR-K1SERIES SERIES n CHARACTERISTIC DATA 4 FTR-K1SERIES SERIES FTR-K1 5 FTR-K1SERIES SERIES FTR-K1 n DIMENSIONS l Dimensions Drilling plan (BOTTOM VIEW) l Wiring diagram (BOTTOM VIEW) l Unit: mm Note: In case of 1 form A, there is no "stationary" contact arm. 6 FTR-K1SERIES SERIES FTR-K1 RoHS Compliance and Lead Free Information 1. General Information All signal and power relays produced by Fujitsu Components are compliant with RoHS directive 2002/95EC including amendments. l Cadmium as used in electrical contacts is exempted from the RoHS directives on October 21st, 2005. (Amendment to Directive 2002/95/EC) l All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf l Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. l 2. Recommended Lead Free Solder Profile Recommended solder Sn-3.0Ag-0.5Cu. l Flow Solder condition: Pre-heating: Soldering: maximum 120˚C dip within 5 sec. at 260˚C solder bath Solder by Soldering Iron: Soldering Iron Temperature: maximum 360˚C Duration: maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. l 4. Tin Whiskers Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. l 7 FTR-K1SERIES SERIES FTR-K1 Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: [email protected] Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: [email protected] Web: emea.fujitsu.com/components/ North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: [email protected] Web: http://us.fujitsu.com/components Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: [email protected] Web: http://www.fujitsu.com/sg/services/micro/components/ ©2010 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users’ own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. April 13, 2010 8