SY54020AR Low Voltage 1.2V/1.8V/2.5V CML 1:4 Fanout Buffer with /EN 3.2Gbps, 3.2GHz General Description The SY54020AR is a fully differential, low voltage 1.2V/1.8V/2.5V CML 1:4 Fanout Buffer with active-low Enable (/EN). The Enable is synchronous so that the outputs will only be enabled/disabled when they are already in the LOW state. This avoids any chance of generating a runt clock pulse when the device is enabled/disabled as can happen with an asynchronous control. When this device is used as a clock fanout, disabling the downstream clock may reduce system power. The SY54020AR can process clock signals as fast as 3.2 GHz or data patterns up to 3.2Gbps. The differential input includes Micrel’s unique, 3-pin input termination architecture that interfaces to LVPECL, LVDS or CML differential signals as small as 100mV (200mVpp) without any level-shifting or termination resistor networks in the signal path. For AC-coupled input interface applications, an internal voltage reference is provided to bias the VT pin. The outputs are CML, with extremely fast rise/fall times guaranteed to be less than 100ps. The SY54020AR operates from a 2.5V ±5% core supply and a 1.2V, 1.8V or 2.5V ±5% output supply and is guaranteed over the full industrial temperature range (– 40°C to +85°C). Datasheets and support documentation can be found on Micrel’s web site at: www.micrel.com. Functional Block Diagram Precision Edge® Features • 1.2V/1.8V/2.5V CML 1:4 Fanout Buffer • Active-low Enable (/EN) input to disable the outputs • Guaranteed AC performance over temperature and voltage: – DC-to > 3.2Gbps Data throughput – DC-to > 3.2GHz Clock throughput – <320 ps propagation delay (IN-to-Q) – <20ps within-device skew – <100 ps rise/fall times • Ultra-low jitter design – <1psRMS cycle-to-cycle jitter • High-speed CML outputs • 2.5V ±5% VCC , 1.2/1.8V/2.5V ±5% VCCO power supply operation • Industrial temperature range: –40°C to +85°C • Available in 16-pin (3mm x 3mm) MLF® package Applications • SONET clock and data distribution • Fibre Channel clock and data distribution • Gigabit Ethernet clock and data distribution Markets • • • • • • • Storage ATE Test and measurement Enterprise networking equipment High-end servers Access Metro area network equipment Precision Edge is a registered trademark of Micrel, Inc. MLF and MicroLeadFrame are registered trademarks of Amkor Technology. Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com April 2009 M9999-041409-A [email protected] or (408) 955-1690 Micrel, Inc. SY54020AR Ordering Information(1) Package Type Operating Range Package Marking Lead Finish SY54020ARMG MLF-16 Industrial 020A with Pb-Free bar-line indicator NiPdAu Pb-Free SY54020ARMGTR(2) MLF-16 Industrial 020A with Pb-Free bar-line indicator NiPdAu Pb-Free Part Number Notes: 1. Contact factory for die availability. Dice are guaranteed at TA = 25°C, DC Electricals only. 2. Tape and Reel. Pin Configuration 16-Pin MLF® (MLF-16) April 2009 2 M9999-041409-A [email protected] or (408) 955-1690 Micrel, Inc. SY54020AR Pin Description Pin Number Pin Name Pin Function 2,3 IN, /IN Differential Input: This input pair is the differential signal input to the device. It accepts differential signals as small as 100mV (200mVPP). Each input pin internally terminates with 50Ω to the VT pin. Note that this input will default to an indeterminate state if left open. Please refer to the “Interface Applications” section for more details. 1 VT Input Termination Center-Tap: Each side of the differential input pair terminates to the VT pin. This pin provides a center-tap to a termination network for maximum interface flexibility. An internal high impedance resistor divider biases VT to allow input AC-coupling. For AC-coupling, bypass VT with 0.1µF low ESR capacitor to VCC. See “Interface Applications” subsection and Figure 2a. 4 /EN Single-ended TTL/CMOS-compatible input functions as a synchronous output enable. The synchronous enable ensures that enable/disable will only occur when the outputs are in a logic LOW state. The input switching threshold is Vcc/2. Note that this input is internally connected to a 25kΩ pull-down resistor and will default to a logic LOW state (Enabled) if left open. Outputs are disabled when /EN is high. See Figure 1b for more details. 16 VCC Positive Power Supply: Bypass with 0.1µF//0.01µF low ESR capacitors as close to the VCC pin as possible. Supplies input and core circuitry. 8,13 VCCO Output Supply: Bypass with 0.1µF//0.01µF low ESR capacitors as close to the VCCO pins as possible. Supplies the output buffers. 5 GND, Ground: Exposed pad must be connected to a ground plane that is the same potential as the ground pin. Exposed pad 15,14 Q0, /Q0 12,11 Q1, /Q1 10,9 Q2, /Q2 7,6 Q3, /Q3 CML Differential Output Pairs: Differential buffered copy of the input signal. The output swing is typically 390mV. See “Interface Applications” subsection for termination information. Truth Table IN /IN /EN Q /Q 0 1 0 0 1 1 0 0 1 0 X X 1 0(1) 1(1) Note: 1. See timing diagram, Figure 1b. April 2009 3 M9999-041409-A [email protected] or (408) 955-1690 Micrel, Inc. SY54020AR Absolute Maximum Ratings(1) Operating Ratings(2) Supply Voltage (VCC) ............................... –0.5V to +3.0V Supply Voltage (VCCO) ............................. –0.5V to +2.7V VCC - VCCO ...............................................................<1.8V VCCO - VCC ...............................................................<0.5V Input Voltage (VIN) ............................–0.5V to VCC + 0.5V CML Output Voltage (VOUT) ............... 0.6V to VCCO+0.5V Current (VT) Source or sink current on VT pin .................±100mA Input Current Source or sink current on (IN, /IN).................±50mA Maximum operating Junction Temperature .......... 125°C Lead Temperature (soldering, 20sec.) .................. 260°C Storage Temperature (Ts) ....................–65°C to +150°C Supply Voltage (VCC) ..............................................2.375V to 2.625V (VCCO) ..............................................1.14V to 2.625V Ambient Temperature (TA) ................... –40°C to +85°C Package Thermal Resistance(3) MLF® Still-air (θJA) ............................................ 75°C/W Junction-to-board (ψJB) ......................... 33°C/W DC Electrical Characteristics (4) TA = –40°C to +85°C, unless otherwise stated. Symbol Parameter Condition Min Typ Max Units VCC Power Supply Voltage Range VCC VCCO VCCO VCCO 2.375 1.14 1.7 2.375 2.5 1.2 1.8 2.5 2.625 1.26 1.9 2.625 V V V V ICC Power Supply Current Max. VCC 40 56 mA ICCO Power Supply Current RIN Input Resistance (IN-to-VT, /IN-to-VT ) No Load. VCCO 64 84 mA 45 50 55 Ω RDIFF_IN Differential Input Resistance (IN-to-/IN) 90 100 110 Ω VIH Input HIGH Voltage (IN, /IN) IN, /IN 1.2 VCC V VIL Input LOW Voltage (IN, /IN) Min. VIL with VIH = 1.2V 0.2 VIH–0.1 V VIH Input HIGH Voltage (IN, /IN) IN, /IN 1.14 VCC V VIL Input LOW Voltage (IN, /IN) VIL with VIH = 1.14V, (1.2V-5%) 0.66 VIH–0.1 V VIN Input Voltage Swing (IN, /IN) See Figure 3a 0.1 1.0 V VDIFF_IN Differential Input Voltage Swing (|IN - /IN|) See Figure 3b 0.2 2.0 V VT_IN Voltage from Input to VT 1.28 V Notes: 1. Permanent device damage may occur if absolute maximum ratings are exceeded. This is a stress rating only and functional operation is not implied at conditions other than those detailed in the operational sections of this datasheet. Exposure to absolute maximum ratings conditions for extended periods may affect device reliability. 2. The data sheet limits are not guaranteed if the device is operated beyond the operating ratings. 3. Package thermal resistance assumes exposed pad is soldered (or equivalent) to the device's most negative potential on the PCB. ψJB and θJA values are determined for a 4-layer board in still-air number, unless otherwise stated. 4. The circuit is designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. April 2009 4 M9999-041409-A [email protected] or (408) 955-1690 Micrel, Inc. SY54020AR CML Outputs DC Electrical Characteristics(5) VCCO = 1.14V to 1.26V, RL = 50Ω to VCCO, VCCO = 1.7V to 1.9V; 2.375V to 2.625V, RL = 50Ω to VCCO or 100Ω across the outputs, VCC = 2.375V to 2.625V. TA = –40°C to +85°C, unless otherwise stated. Symbol Parameter Condition Min Typ Max Units VOH Output HIGH Voltage RL = 50Ω to VCCO VCCO-0.020 VCCO-0.010 VCCO V VOUT Output Voltage Swing See Figure 3a 300 390 475 mV VDIFF_OUT Differential Output Voltage Swing ROUT Output Source Impedance See Figure 3b 600 780 950 mV 45 50 55 Ω Min Typ Max Units VCC V 0.8 V 200 µA 75 µA LVTTL/CMOS DC Electrical Characteristics (5) VCC = 2.5V ±5%, TA = –40°C to +85°C, unless otherwise stated. Symbol Parameter Condition VIH Input HIGH Voltage VIL Input LOW Voltage 2.0 IIH Input HIGH Current VIH = VCC IIL Input LOW Current VIL = 0V -5 Note: 5. The circuit is designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. April 2009 5 M9999-041409-A [email protected] or (408) 955-1690 Micrel, Inc. SY54020AR AC Electrical Characteristics VCCO = 1.14V to 1.26V, RL = 50Ω to VCCO VCCO = 1.7V to 1.9V, 2.375V to 2.625V, RL = 50Ω to VCCO or 100Ω across the outputs. VCC = 2.375V to 2.625V. TA = –40°C to +85°C, unless otherwise stated. Symbol Parameter Condition Min fMAX Maximum Data Rate/ Frequency NRZ Data 3.2 Gbps Clock 3.2 GHz VIN > 200mV, Note 6, Figure 1a 150 VOUT > 200mV Units Propagation Delay tS Setup Time /EN 200 ps tH Hold Time /EN 100 ps tSKEW Output-to-Output Skew Note 7 Part-to-Part Skew Note 8 Data Clock 8 320 ps 20 ps 75 ps Random Jitter Note 9 1 psRMS Deterministic Jitter Note 10 10 psPP Cycle-to-Cycle Jitter Note 11 1 psRMS Note 12 10 psPP 100 ps % Total Jitter tR, tF 220 Max tPD tJitter IN-to-Q Typ Output Rise/Fall Times (20% to 80%) At full output swing. Duty Cycle Differential I/O ≤2.5GHz 47 53 ≤3.2GHz 45 55 35 60 Notes: 6. Propagation delay is measured with input tr/tf ≤ 300 ps (20% to 80%) 7. Output-to-Output skew is the difference in time between both outputs, receiving data from the same input, for the same temperature, voltage and transition. 8. Part-to-part skew is defined for two parts with identical power supply voltages at the same temperature and no skew at the edges of the respective inputs. 9. Random jitter is measured with a K28.7 pattern, measured at ≤ fMAX. 23 10. Deterministic jitter is measured at 2.5Gbps with both K28.5 and 2 –1 PRBS pattern. 11. Cycle-to-cycle jitter definition: the variation period between adjacent cycles over a random sample of adjacent cycle pairs. tJITTER_CC = Tn –Tn+1, where T is the time between rising edges of the output signal. 12 12. Total jitter definition: with an ideal clock input frequency of ≤ fMAX (device), no more than one output edge in 10 output edges will deviate by more than the specified peak-to-peak jitter value. April 2009 6 M9999-041409-A [email protected] or (408) 955-1690 Micrel, Inc. SY54020AR CML Output Termination with VCCO 1.8V, 2.5V For VCCO of 1.8V and 2.5V, Figure 5a and Figure 5b, terminate with either 50Ω to VCCO or 100Ω differentially across the outputs. See Figure 5c for AC-coupling. Interface Applications For Input Interface Applications, see Figures 4a through 4f. For CML Output Termination, see Figures 5a through 5d. CML Output Termination with VCCO 1.2V For VCCO of 1.2V, Figure 5a, terminate the output with 50Ω to1.2V, DC-coupled, not 100Ω differentially across the outputs. If AC-coupling is used, Figure 5d, terminate into 50Ω to 1.2V before the coupling capacitor and then connect to a high value resistor to a reference voltage. Do not AC-couple with internally terminated receiver, such as 50Ω ANY-IN input. AC coupling will offset the output voltage by 200mV and this offset voltage will be too low for proper driver operation. Any unused output pair needs to be terminated when VCCO is 1.2V. Do not leave floating. April 2009 Input AC-Coupling The SY54020AR input can accept AC coupling from any driver. Bypass VT with a 0.1µF low ESR capacitor to VCC as shown in Figures 4c and 4d. VT has an internal high impedance resistor divider as shown in Figure 2a, to provide a bias voltage for AC-coupling. 7 M9999-041409-A [email protected] or (408) 955-1690 Micrel, Inc. SY54020AR Timing Diagrams Figure 1a. Propagation Delay Figure 1b. Output Enable/Disable Timing Diagram April 2009 8 M9999-041409-A [email protected] or (408) 955-1690 Micrel, Inc. SY54020AR Typical Characteristics VCC = 2.5V, VCCO = 1.2V GND = 0V, VIN = 400mV, RL = 50Ω to 1.2V, TA = 25°C, unless otherwise stated. April 2009 9 M9999-041409-A [email protected] or (408) 955-1690 Micrel, Inc. SY54020AR Functional Characteristics VCC = 2.5V, VCCO =1.2V, GND = 0V, VIN = 400mV, RL = 50Ω to 1.2V, TA = 25°C, unless otherwise stated. April 2009 10 M9999-041409-A [email protected] or (408) 955-1690 Micrel, Inc. SY54020AR Input and Output Stage Figure 2b. Simplified CML Output Buffer Figure 2a. Simplified Differential Input Buffer Single-Ended and Differential Swings Figure 3a. Single-Ended Swing April 2009 Figure 3b. Differential Swing 11 M9999-041409-A [email protected] or (408) 955-1690 Micrel, Inc. SY54020AR Input Interface Applications Figure 4a. CML Interface (DC-Coupled, 1.8V, 2.5V) Figure 4b. CML Interface (DC-Coupled, 1.2V) Figure 4c. CML Interface (AC-Coupled) Figure 4e. LVPECL Interface (DC-Coupled) Figure 4f. LVDS Interface Option: may connect VT to VCC Figure 4d. LVPECL Interface (AC-Coupled) April 2009 12 M9999-041409-A [email protected] or (408) 955-1690 Micrel, Inc. SY54020AR CML Output Termination Figure 5a. 1.2V, 1.8V or 2.5V CML DC-Coupled Termination Figure 5b. 1.8V or 2.5V CML DC-Coupled Termination Figure 5c. CML AC-Coupled Termination (VCCO 1.8V or 2.5V ) Figure 5d. CML AC-Coupled Termination (VCCO 1.2V only) April 2009 13 M9999-041409-A [email protected] or (408) 955-1690 Micrel, Inc. SY54020AR Package Information 16-Pin MLF® (3mm x3mm) (MLF-16) MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2009 Micrel, Incorporated. April 2009 14 M9999-041409-A [email protected] or (408) 955-1690