MITSUBISHI <INTELLIGENT POWER MODULES> PM100CLA060 FLAT-BASE TYPE INSULATED PACKAGE PM100CLA060 FEATURE a) Adopting new 5th generation IGBT (CSTBT) chip, which performance is improved by 1µm fine rule process. For example, typical Vce(sat)=1.5V @Tj=125°C b) I adopt the over-temperature conservation by Tj detection of CSTBT chip, and error output is possible from all each conservation upper and lower arm of IPM. c) New small package Reduce the package size by 10%, thickness by 22% from S-DASH series. • 3φ 100A, 600V Current-sense IGBT type inverter • Monolithic gate drive & protection logic • Detection, protection & status indication circuits for, shortcircuit, over-temperature & under-voltage (P-Fo available from upper arm devices) • Acoustic noise-less 11kW class inverter application • UL Recognized Yellow Card No.E80276(N) File No.E80271 APPLICATION General purpose inverter, servo drives and other motor controls PACKAGE OUTLINES Dimensions in mm 11 120 106 7 19.75 3.25 16 16 16 3-2 3-2 3-2 16 15.25 2-φ5.5 MOUNTING HOLES 6-2 3 2-φ2.5 55 N 17.5 12 19.75 5 9 13 19 U V W 13.5 B 6-M5 NUTS 22 +– 10.5 12 32.75 23 23 23 Terminal code 19-■0.5 31 13 7 (SCREWING DEPTH) 10.75 12 11.75 14.5 32 P 17.5 1 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. VUPC UFO UP VUP1 VVPC VFO VP VVP1 VWPC WFO 11. 12. 13. 14. 15. 16. 17. 18. 19. WP VWP1 VNC VN1 NC UN VN WN Fo May 2005 MITSUBISHI <INTELLIGENT POWER MODULES> PM100CLA060 FLAT-BASE TYPE INSULATED PACKAGE INTERNAL FUNCTIONS BLOCK DIAGRAM NC Fo VNC WN VN1 WP VWP1 VWPC WFO UN VN 1.5k VP VVPC 1.5k Gnd In Gnd Fo Vcc Si Out OT NC Gnd In Gnd Fo Vcc Si Out OT Gnd In Gnd Fo Vcc Si Out OT N Gnd In Gnd UP VUPC VUP1 UFO 1.5k Fo Vcc Si Out VVP1 VFO OT Gnd In Gnd W V 1.5k Fo Vcc Si Out Gnd In OT Gnd Fo Vcc Si Out U OT P MAXIMUM RATINGS (Tj = 25°C, unless otherwise noted) INVERTER PART Symbol VCES ±IC ±ICP PC Tj Parameter Collector-Emitter Voltage Collector Current Collector Current (Peak) Collector Dissipation Junction Temperature Condition VD = 15V, VCIN = 15V TC = 25°C TC = 25°C TC = 25°C (Note-1) Ratings 600 100 200 462 –20 ~ +150 Unit V A A W °C Ratings Unit 20 V 20 V 20 V 20 mA CONTROL PART Symbol Parameter VD Supply Voltage VCIN Input Voltage VFO Fault Output Supply Voltage IFO Fault Output Current Condition Applied between : VUP1-VUPC VVP1-VVPC, VWP1-VWPC, VN1-VNC Applied between : UP-VUPC, VP-VVPC WP-VWPC, UN • VN • WN-VNC Applied between : UFO-VUPC, VFO-VVPC, WFO-VWPC FO-VNC Sink current at UFO, VFO, WFO, FO terminals May 2005 MITSUBISHI <INTELLIGENT POWER MODULES> PM100CLA060 FLAT-BASE TYPE INSULATED PACKAGE TOTAL SYSTEM Symbol Parameter Supply Voltage Protected by VCC(PROT) SC VCC(surge) Supply Voltage (Surge) Storage Temperature Tstg Isolation Voltage Viso Ratings Condition VD = 13.5 ~ 16.5V, Inverter Part, Tj = +125°C Start Applied between : P-N, Surge value 60Hz, Sinusoidal, Charged part to Base, AC 1 min. Unit 400 V 500 –40 ~ +125 2500 V °C Vrms THERMAL RESISTANCES Symbol Condition Parameter Rth(j-c)Q Rth(j-c)F Junction to case Thermal Resistances Rth(c-f) Contact Thermal Resistance Inverter IGBT (per 1 element) Inverter FWDi (per 1 element) Case to fin, (per 1 module) Thermal grease applied (Note-1) (Note-1) (Note-1) Min. — — Limits Typ. — — Max. 0.27* 0.43* — — 0.038 Limits Typ. 1.6 1.5 2.2 1.0 0.2 0.4 1.2 0.5 — — Max. 2.1 2.0 3.3 2.4 0.4 1.0 2.5 1.0 1 10 Unit °C/W * If you use this value, Rth(f-a) should be measured just under the chips. (Note-1) Tc (under the chip) measurement point is below. arm axis X Y UP IGBT FWDi 28.3 28.0 –8.5 1.7 VP IGBT FWDi 65.0 65.2 –8.5 1.7 WP IGBT FWDi 87.0 87.2 –8.5 1.7 (unit : mm) UN IGBT FWDi 39.3 39.5 6.5 –5.2 VN IGBT FWDi 54.0 53.7 6.5 –5.2 WN IGBT FWDi 76.0 75.7 6.5 –5.2 Bottom view ELECTRICAL CHARACTERISTICS (Tj = 25°C, unless otherwise noted) INVERTER PART Symbol VCE(sat) VEC ton trr tc(on) toff tc(off) ICES Parameter Condition Collector-Emitter Saturation Voltage FWDi Forward Voltage VD = 15V, IC = 100A VCIN = 0V (Fig. 1) –IC = 100A, VD = 15V, VCIN = 15V Switching Time VD = 15V, VCIN = 0V↔15V VCC = 300V, IC = 100A Tj = 125°C Inductive Load Collector-Emitter Cutoff Current VCE = VCES, VCIN = 15V Tj = 25°C Tj = 125°C (Fig. 2) (Fig. 3,4) (Fig. 5) Tj = 25°C Tj = 125°C Min. — — — 0.5 — — — — — — Unit V V µs mA May 2005 MITSUBISHI <INTELLIGENT POWER MODULES> PM100CLA060 FLAT-BASE TYPE INSULATED PACKAGE CONTROL PART Symbol Parameter Condition VN1-VNC V*P1-V*PC ID Circuit Current VD = 15V, VCIN = 15V Vth(ON) Vth(OFF) SC Input ON Threshold Voltage Input OFF Threshold Voltage Short Circuit Trip Level Short Circuit Current Delay Time Applied between : UP-VUPC, VP-VVPC, WP-VWPC UN • VN • WN-VNC (Fig. 3,6) –20 ≤ Tj ≤ 125°C, VD = 15V toff(SC) OT OTr UV UVr IFO(H) IFO(L) tFO VD = 15V (Fig. 3,6) Over Temperature Protection VD = 15V Detect Tj of IGBT chip Supply Circuit Under-Voltage Protection –20 ≤ Tj ≤ 125°C Fault Output Current VD = 15V, VFO = 15V (Note-2) Minimum Fault Output Pulse Width VD = 15V (Note-2) Trip level Reset level Trip level Reset level Min. — — 1.2 1.7 200 Limits Typ. 15 5 1.5 2.0 — Max. 25 10 1.8 2.3 — Unit mA V A — 0.2 — µs 135 — 11.5 — — — 145 125 12.0 12.5 — 10 — — 12.5 — 0.01 15 °C 1.0 1.8 — V mA ms (Note-2) Fault output is given only when the internal SC, OT & UV protections schemes of either upper or lower arm device operate to protect it. MECHANICAL RATINGS AND CHARACTERISTICS Symbol — — — Condition Parameter Mounting torque Mounting torque Weight Main terminal Mounting part screw : M5 screw : M5 — Min. 2.5 2.5 — Limits Typ. 3.0 3.0 380 Max. 3.5 3.5 — Unit N•m N•m g RECOMMENDED CONDITIONS FOR USE Symbol VCC Parameter Supply Voltage VD Control Supply Voltage VCIN(ON) VCIN(OFF) fPWM Input ON Voltage Input OFF Voltage PWM Input Frequency Arm Shoot-through Blocking Time tdead Condition Applied across P-N terminals Applied between : VUP1-VUPC, VVP1-VVPC VWP1-VWPC, VN1-VNC (Note-3) Applied between : UP-VUPC, VP-VVPC, WP-VWPC UN • VN • WN-VNC Using Application Circuit of Fig. 8 For IPM’s each input signals Recommended value ≤ 400 Unit V 15 ± 1.5 V (Fig. 7) ≤ 0.8 ≥ 9.0 ≤ 20 kHz ≥ 2.0 µs V (Note-3) With ripple satisfying the following conditions: dv/dt swing ≤ ±5V/µs, Variation ≤ 2V peak to peak May 2005 MITSUBISHI <INTELLIGENT POWER MODULES> PM100CLA060 FLAT-BASE TYPE INSULATED PACKAGE PRECAUTIONS FOR TESTING 1. Before appling any control supply voltage (VD), the input terminals should be pulled up by resistores, etc. to their corresponding supply voltage and each input signal should be kept off state. After this, the specified ON and OFF level setting for each input signal should be done. 2. When performing “SC” tests, the turn-off surge voltage spike at the corresponding protection operation should not be allowed to rise above VCES rating of the device. (These test should not be done by using a curve tracer or its equivalent.) P, (U,V,W) IN Fo VCIN P, (U,V,W) Ic V IN Fo VCIN –Ic V (15V) (0V) U,V,W, (N) VD (all) U,V,W, (N) VD (all) Fig. 1 VCE(sat) Test Fig. 2 VEC Test a) Lower Arm Switching P VCIN (15V) Fo Signal input (Upper Arm) trr CS Ic Vcc Fo Signal input (Lower Arm) VCIN VCE Irr U,V,W 90% 90% N VD (all) b) Upper Arm Switching Ic 10% 10% 10% 10% P Fo Signal input (Upper Arm) VCIN tc(on) VCIN U,V,W CS VCIN (15V) tc(off) Vcc td(on) tr td(off) tf Fo Signal input (Lower Arm) (ton= td(on) + tr) (toff= td(off) + tf) N Ic VD (all) Fig. 3 Switching time and SC test circuit Fig. 4 Switching time test waveform VCIN Short Circuit Current P, (U,V,W) A VCIN (15V) Constant Current IN Fo SC Pulse VCE Ic VD (all) U,V,W, (N) Fo toff(SC) Fig. 5 ICES Test Fig. 6 SC test waveform IPM’ input signal VCIN (Upper Arm) 1.5V 0V IPM’ input signal VCIN (Lower Arm) 0V 2V tdead 2V 1.5V 1.5V 2V tdead t t tdead 1.5V: Input on threshold voltage Vth(on) typical value, 2V: Input off threshold voltage Vth(off) typical value Fig. 7 Dead time measurement point example May 2005 MITSUBISHI <INTELLIGENT POWER MODULES> PM100CLA060 FLAT-BASE TYPE INSULATED PACKAGE P ≥10µ 20k VUP1 → VD UFo IF 1.5k Vcc Fo UP OT OUT VUPC + – Si In U GND GND ≥0.1µ VVP1 VFo VD 1.5k Fo VP 1.5k Vcc Fo WP Vcc ≥10µ Fo UN OT OUT Si W OT OUT Si In GND GND ≥0.1µ N OT 20k → M GND GND 20k IF V In VWPC → Si GND GND VWP1 VD OT OUT In VVPC WFo Vcc Vcc ≥10µ IF Fo VN OUT Si In GND GND ≥0.1µ 20k → VD VN1 Vcc ≥10µ IF Fo WN ≥0.1µ In OT OUT Si GND GND VNC NC NC 5V 1k Fo 1.5k : Interface which is the same as the U-phase Fig. 8 Application Example Circuit NOTES FOR STABLE AND SAFE OPERATION ; Design the PCB pattern to minimize wiring length between opto-coupler and IPM’s input terminal, and also to minimize the stray capacity between the input and output wirings of opto-coupler. Connect low impedance capacitor between the Vcc and GND terminal of each fast switching opto-coupler. Fast switching opto-couplers: tPLH, tPHL ≤ 0.8µs, Use High CMR type. Slow switching opto-coupler: CTR > 100% Use 4 isolated control power supplies (VD). Also, care should be taken to minimize the instantaneous voltage charge of the power supply. Make inductance of DC bus line as small as possible, and minimize surge voltage using snubber capacitor between P and N terminal. Use line noise filter capacitor (ex. 4.7nF) between each input AC line and ground to reject common-mode noise from AC line and improve noise immunity of the system. • • • • • • • May 2005 MITSUBISHI <INTELLIGENT POWER MODULES> PM100CLA060 FLAT-BASE TYPE INSULATED PACKAGE PERFORMANCE CURVES COLLECTOR-EMITTER SATURATION VOLTAGE (VS. Ic) CHARACTERISTICS (INVERTER PART · TYPICAL) OUTPUT CHARACTERISTICS (INVERTER PART · TYPICAL) 100 VD = 17V 60 40 20 0 0.5 1 1.5 2 2 VD = 15V 1.5 1 0.5 Tj = 25°C Tj = 125°C 0 0 20 40 60 80 100 COLLECTOR-EMITTER VOLTAGE VCE (V) COLLECTOR CURRENT IC (A) COLLECTOR-EMITTER SATURATION VOLTAGE (VS. VD) CHARACTERISTICS (INVERTER PART · TYPICAL) 2 SWITCHING TIME CHARACTERISTICS (TYPICAL) 1.5 1 0.5 IC = 100A Tj = 25°C Tj = 125°C 0 12 101 7 5 4 3 2 13 14 15 16 17 7 VCC = 300V 5 VD = 15V Tj = 25°C 4 Tj = 125°C 3 2 Inductive load 100 7 5 4 3 tc(off) tc(on) tc(off) 2 10–1 18 4 5 7 101 2 3 4 5 7 102 2 3 CONTROL SUPPLY VOLTAGE VD (V) COLLECTOR CURRENT IC (A) SWITCHING TIME CHARACTERISTICS (TYPICAL) SWITCHING LOSS CHARACTERISTICS (TYPICAL) VCC = 300V VD = 15V Tj = 25°C Tj = 125°C Inductive load ton 100 toff 7 5 4 3 toff 2 10–1 101 SWITCHING TIME tc(on), tc(off) (µs) COLLECTOR-EMITTER SATURATION VOLTAGE VCE (sat) (V) 13V 80 0 SWITCHING TIME ton, toff (µs) 15V 4 5 7 101 2 3 4 5 7 102 2 COLLECTOR CURRENT IC (A) 3 SWITCHING LOSS ESW(on), ESW(off) (mJ/pulse) COLLECTOR CURRENT IC (A) Tj = 25°C COLLECTOR-EMITTER SATURATION VOLTAGE VCE (sat) (V) 120 101 ESW(on) 7 5 4 3 2 ESW(off) 100 7 5 4 3 2 VCC = 300V VD = 15V Tj = 25°C Tj = 125°C Inductive load 10–1 7 5 4 2 3 4 5 7 101 2 3 4 5 7 102 2 COLLECTOR CURRENT IC (A) May 2005 MITSUBISHI <INTELLIGENT POWER MODULES> PM100CLA060 102 VD = 15V 7 5 4 3 2 101 7 5 4 3 2 100 Tj = 25°C Tj = 125°C 0 0.5 1 1.5 2 7 5 4 3 Irr 2 7 5 4 3 2 10–1 trr 7 5 4 3 101 7 5 4 3 2 10–2 2.5 2 3 4 5 7 101 VCC = 300V VD = 15V Tj = 25°C 2 Tj = 125°C Inductive load 100 2 3 4 5 7 102 2 3 EMITTER-COLLECTOR VOLTAGE VEC (V) COLLECTOR RECOVERY CURRENT –IC (A) ID VS. fc CHARACTERISTICS (TYPICAL) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (INVERTER PART) 100 VD = 15V Tj = 25°C 40 N-side 30 20 P-side 10 0 0 5 10 15 fc (kHz) 20 25 NORMALIZED TRANSIENT THERMAL IMPEDANCE Zth (j – c) 50 ID (mA) DIODE REVERSE RECOVERY CHARACTERISTICS (TYPICAL) 100 102 REVERSE RECOVERY CURRENT lrr (A) DIODE FORWARD CHARACTERISTICS (INVERTER PART · TYPICAL) REVERSE RECOVERY TIME trr (µs) COLLECTOR RECOVERY CURRENT –IC (A) FLAT-BASE TYPE INSULATED PACKAGE 7 5 3 2 10–1 7 5 3 2 10–2 Single Pulse 7 5 IGBT Part; Per unit base = Rth(j – c)Q = 0.27°C/ W 3 FWDi Part; 2 Per unit base = Rth(j – c)F = 0.43°C/ W 10–3 –5 10 2 3 5 710–4 2 3 5 710–3 2 3 5 710–2 2 3 5 710–1 2 3 5 7100 2 3 5 7101 TIME (s) May 2005