bq24020,, bq24022,, bq24023 bq24024, bq24025, bq24026 bq24027 www.ti.com SLUS549D – DECEMBER 2002 – REVISED MARCH 2006 SINGLE-CHIP, LI-ION AND LI-POL CHARGER IC WITH AUTONOMOUS USB-PORT AND AC-ADAPTER SUPPLY MANAGEMENT (bqTINY™-II) FEATURES • • • • • • • • • DESCRIPTION Small 3 mm x 3 mm MLP Package Charges and powers Systems from Either AC Adapter or USB With Autonomous power-Source Selection Integrated USB Control With Selectable 100 mA and 500 mA Charge Rates Ideal for Low-Dropout Charger Designs for Single-Cell Li-Ion or Li-pol Packs in Space Limited portable applications Integrated power FET and Current Sensor for Up to 1-A Charge applications From AC Adapter Precharge Conditioning With Safety Timer power Good (AC Adapter Present) Status Output Optional Battery Temperature Monitoring Before and During Charge Automatic Sleep Mode for Low-power Consumption APPLICATIONS • • • • The bqTINY-II series are highly-integrated, flexible Li-Ion linear charge and system power management devices for space-limited charger applications. In a single monolithic device, the bqTINY-II offers integrated USB-port and ac-adapter supply management with autonomous power-source selection, power-FET and current-sensor interfaces, high-accuracy current and voltage regulation, charge status, and charge termination. The bqTINY-II automatically selects the USB-port or the ac-adapter as the power source for the system. In the USB configuration, the host can select from two preset charge rates of 100 mA or 500 mA. In the ac-adapter configuration, an external resistor sets the system or charge current. The bqTINY-II charges the battery in three phases: conditioning, constant current, and constant voltage. Charge is terminated based on minimum current. An internal charge timer provides a backup safety for charge termination. The bqTINY-II automatically restarts the charge if the battery voltage falls below an internal threshold. The bqTINY-II automatically enters sleep mode when both supplies are removed. PDAs, MP3 Players Digital Cameras Internet appliances Smartphones VDC AC ADAPTER PACK+ bq24020DRC 1 AC OUT + 10 GND VBUS USB PORT GND BATTERY PACK SYSTEM PACK− 2 USB TS 9 3 STAT1 CE 8 4 STAT2 ISET2 7 5 VSS 6 SYSTEM INTERFACE RSET ISET1 D+ D− UDG−02184 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. bqTINY is a trademark of Texas Instruments. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2002–2006, Texas Instruments Incorporated bq24020,, bq24022,, bq24023 bq24024, bq24025, bq24026 bq24027 www.ti.com SLUS549D – DECEMBER 2002 – REVISED MARCH 2006 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Different versions of the bqTINY-II offer many additional features. These include a temperature-sensor input for detecting hot or cold battery packs, a power-good output (PG) indicating the presence of input power, a TTL-level charge-enable input (CE) used to disable or enable the charge process, and a TTL-level timer and taper-detect enable input (TTE) used to disable or enable the fast-charge timer and charge termination. ORDERING INFORMATION CHARGE REGULATION VOLTAGE (V)(1) TJ – 40°C to 125°C (1) OPTIONAL FUNCTIONS (1) FAST-CHARGE TIMER (Hours) TAPER TIMER USB TAPER THRESHOLD PART NUMBER(2) 4.2 CE and TS 5 Yes 10% of ISET1 Level bq24020DRCR AZS 4.2 PG and CE 5 Yes 10% of ISET1 Level bq24022DRCR AZU 4.2 CE and TTE 5 Yes 10% of ISET1 Level bq24023DRCR AZV 4.2 TTE and TS 5 Yes 10% of ISET1 Level bq24024DRCR AZW 4.2 CE and TS 7 Yes 10% of ISET1 Level bq24025DRCR AZX 4.2 TE and TS 7 No 10% of selected USB charge rate bq24026DRCR ANR 4.2 PG and CE 7 No 10% of selected USB charge rate bq24027DRCR ANS MARKINGS The DRC package is available taped and reeled only in quantities of 3,000 devices per reel. Dissipation Ratings (1) PACKAGE θJA TA < 40°C POWER RATING DERATING FACTOR ABOVE TA = 25°C DRC (1) 46.87 °C/W 1.5 W 0.021 W/°C This data is based on using the JEDEC High-K board and the exposed die pad is connected to a copper pad on the board. This is connected to the ground plane by a 2x3 via matrix. ABSOLUTE MAXIMUM RATINGS (1) over operating free-air temperature range (unless otherwise noted) bq24020, bq24022, bq24023, bq24024 bq24025, bq24026 bq24027 Input voltage (2) AC, CE, ISET1, ISET2, OUT, PG, STAT1, STAT2, TE, TS, TTE, USB –0.3 to 7.0 V Output sink/source current STAT1, STAT2, PG 15 mA Output current TS 200 µA Output current OUT 1.5 A Operating free-air temperature range, TA –40 to 125 Junction temperature range, TJ Storage temperature, Tstg –65 to 150 Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds (1) (2) 2 UNIT °C 300 Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltages are with respect to VSS. Submit Documentation Feedback bq24020,, bq24022,, bq24023 bq24024, bq24025, bq24026 bq24027 www.ti.com SLUS549D – DECEMBER 2002 – REVISED MARCH 2006 RECOMMENDED OPERATING CONDITIONS over operating free-air temperature range (unless otherwise noted) MIN Supply voltage (from AC input), VCC NOM MAX UNIT 4.5 6.5 V Supply voltage (from USB input), VCC 4.35 6.5 V Operating junction temperature range, TJ –40 125 °C ELECTRICAL CHARACTERISTICS over 0°C ≤ TJ ≤ 125°C and recommended supply voltage, unless otherwise noted PARAMETER TEST CONDITIONS MIN TYP MAX 1.2 2.0 UNIT INPUT CURRENT ICC(VCC) VCC current VCC > VCC(min) ICC(SLP) Sleep current Sum of currents into OUT pin, VCC < V(SLP) ICC(STBY) Standby current CE = High 0°C ≤TJ ≤ 85°C IIB(OUT) Input current on OUT pin Charge DONE VCC > VCC(MIN) IIB(CE) Input current on CE pin 1 IIB(TTE) Input bias current on TTE pin 1 IIB(TE) Input bias current on TE pin 1 2 5 1 150 5 mA µA VOLTAGE REGULATION VO(REG) + V(DO-MAX) ≤ VCC , I(TERM) < IO(OUT) ≤ 1 A VO(REG) Output voltage, 4.20 Voltage regulation accuracy V(DO) AC dropout voltage (V(AC)–V(OUT)) V(DO) USB dropout voltage (V(USB) – V(OUT)) TA = 25°C V –0.35% 0.35% –1% 1% VO(OUT) = VO(REG) VO(REG) + V(DO-MAX)) ≤ VCC IO(OUT) = 1A 350 500 VO(OUT) = VO(REG) VO(REG) + V(DO-MAX)) ≤ VCC ISET2 = High 350 500 VO(OUT) = VO(REG) VO(REG) + V(DO-MAX)) ≤ VCC ISET2 = Low 60 100 VI(OUT) > V(LOWV) VI(AC)– VI(OUT) > V(DO-MAX) VCC ≥ 4.5 V 50 1000 VCC(MIN) ≥ 4.5 V VUSB– VI(OUT) > V(DO-MAX) VI(OUT) > V(LOWV) ISET2 = Low 80 100 VCC(MIN) ≥ 4.5 V VUSB– VI(OUT) > V(DO-MAX) VI(OUT) > V(LOWV) ISET2 = High 400 500 mV CURRENT REGULATION IO(OUT) AC output current range (1) IO(OUT) USB output current range V(SET) Output current set voltage K(SET) Output current set factor (1) IO(OUT) + ǒK(SET) Voltage on ISET1 pin, VCC ≥ 4.5 V, VIN ≥ 4.5 V, VI(OUT) > V(LOWV), VIN– VI(OUT) > V(DO-MAX) 2.463 2.500 2.538 50 mA ≤ IO(OUT) ≤ 1 A 307 322 337 10 mA ≤ IO(OUT) < 50 mA 296 320 346 1 mA ≤ IO(OUT) < 10 mA 246 320 416 mA V Ǔ V(SET) RSET Submit Documentation Feedback 3 bq24020,, bq24022,, bq24023 bq24024, bq24025, bq24026 bq24027 www.ti.com SLUS549D – DECEMBER 2002 – REVISED MARCH 2006 ELECTRICAL CHARACTERISTICS (continued) over 0°C ≤ TJ ≤ 125°C and recommended supply voltage, unless otherwise noted PARAMETER TEST CONDITIONS MIN TYP MAX UNIT PRECHARGE AND SHORT-CIRCUIT CURRENT REGULATION V(LOWV) IO(PRECHG) V(PRECHG) Precharge to fast-charge transition threshold Voltage on OUT pin 2.8 3.0 3.2 Deglitch time for fast-charge to precharge transition VCC(MIN) ≥ 4.5 V, tFALL = 100 ns, 10 mV overdrive, VI(OUT) decreasing below threshold 250 375 500 Precharge range (2) 0 V < VI(OUT) < V(LOWV), t < t(PRECHG) Precharge set voltage Voltage on ISET1 pin 0 V < VI(OUT) > V(LOWV), VO(REG) = 4.2 V t < t(PRECHG) 5 240 100 255 270 V ms mA mV CHARGE TAPER AND TERMINATION DETECTION I(TAPER) Charge taper detection range (3) VI(OUT) > V(RCH), t < t(TAPER) USB-100 charge taper detection level bq24026 VI(OUT) > V(RCH), ISET2 = Low 6.5 9 11 bq24026 VI(OUT) > V(RCH), ISET2 = High 32 44 55 USB-500 charge taper detection level 5 100 mA V(TAPER) Charge taper detection set voltage Voltage on ISET1 pin, VO(REG) = 4.2 V, VI(OUT) > V(RCH), t < t(TAPER) 235 250 265 V(TERM) Charge termination detection set voltage (4) Voltage on ISET1 pin, VO(REG) = 4.2 V, VI(OUT) > V(RCH) 11 18 25 375 500 Deglitch time for TAPER detection VCC(MIN) ≥ 4.5 V, tFALL = 100 ns charging current increasing or decreasing above and below, 10 mV overdrive 250 t(TPRDET) t(TRMDET) Deglitch time for termination detection VCC(MIN) ≥ 4.5 V, tFALL = 100 ns charging current decreasing below, 10 mV overdrive 250 375 500 mV ms TEMPERATURE SENSE COMPARATOR V(HTF) High-voltage threshold PTC thermistor 2.475 2.500 2.525 V(LTF) Low-voltage threshold PTC thermistor 0.485 0.500 0.515 I(TS) Current source 96 102 108 µA t(DEGL) Deglitch time for temperature fault 250 375 500 ms (2) (3) (4) 4 IO(PRECHG) + IO(TAPER) + IO(TERM) + Ǔ ǒK(SET) V(PRECHG) RSET ǒK(SET) Ǔ V(TAPER) R SET ǒK(SET) Ǔ V(TERM) RSET Submit Documentation Feedback V bq24020,, bq24022,, bq24023 bq24024, bq24025, bq24026 bq24027 www.ti.com SLUS549D – DECEMBER 2002 – REVISED MARCH 2006 ELECTRICAL CHARACTERISTICS (continued) over 0°C ≤ TJ ≤ 125°C and recommended supply voltage, unless otherwise noted PARAMETER TEST CONDITIONS MIN TYP MAX VO(REG) – 0.115 VO(REG) – 0.10 VO(REG) – 0.085 250 375 500 UNIT BATTERY RECHARGE THRESHOLD VRCH Recharge threshold t(DEGL) Deglitch time for recharge detect VCC(MIN) ≥ 4.5 V, tFALL = 100 ns decreasing below or increasing above threshold, 10 mV overdrive V ms STAT1, STAT2, and PG OUTPUTS VOL Low-level output saturation voltage IO = 5 mA 0.25 V ISET2, CHARGE ENABLE (CE), TIMER AND TERMINATION ENABLE (TTE), AND TIMER ENABLE (TE) INPUTS VIL Low-level input voltage IIL = 10 µA 0 VIH High-level input voltage IIL = 20 µA 1.4 IIL CE, TE or TTE low-level input current IIH CE, TE or TTE high-level input current IIL ISET2 low-level input current IISET2 = 0 IIH ISET2 high-level input current IISET2 = VCC IIH ISET2 high-Z input current 0.4 V –1 1 µA –20 40 1 V TIMERS t(PRECHG) t(TAPER) t(CHG) I(FAULT) Precharge time Taper time Charge time 1,620 1,800 1,930 bq24020 bq24022 bq24023 bq24024 bq24025 1,620 1,800 1,930 bq24020 bq24022 bq24023 bq24024 16,200 18,000 19,300 bq24025 bq24026 bq24027 22,680 25,200 27,720 Timer fault recovery current s µA 200 SLEEP COMPARATOR V(SLP) Sleep-mode entry threshold voltage V(SLPEXIT) Sleep mode exit threshold voltage 2.3 V ≤ VI(OUT) ≤ VO(REG) Sleep mode deglitch time AC and USB decreasing below threshold, tFALL = 100 ns, 10 mV overdrive VCC ≤ VI(OUT) +80 mV 2.3 V ≤ VI(OUT) ≤ VO(REG) VCC ≥ VI(OUT) +190mV 250 375 500 V ms THERMAL SHUTDOWN THRESHOLDS T(SHTDWN) Thermal trip threshold 165 Thermal hysteresis °C 15 UNDERVOLTAGE LOCKOUT V(UVLO) Undervoltage lockout Decreasing VCC Hysteresis 2.4 2.5 27 Submit Documentation Feedback 2.6 V mV 5 bq24020,, bq24022,, bq24023 bq24024, bq24025, bq24026 bq24027 www.ti.com SLUS549D – DECEMBER 2002 – REVISED MARCH 2006 DRC PACKAGE (TOP VIEW) VSS STAT2 STAT1 USB 5 4 3 2 AC DRC PACKAGE (TOP VIEW) VSS STAT2 STAT1 USB 1 5 bq24020DRC bq24025DRC 6 7 ISET1 ISET2 CE 10 TS OUT DRC PACKAGE (TOP VIEW) VSS STAT2 STAT1 USB 5 4 3 3 2 1 bq24022DRC 9 8 4 AC 2 6 7 8 ISET1 ISET2 PG 9 10 CE OUT DRC PACKAGE (TOP VIEW) AC VSS STAT2 STAT1 USB 1 5 4 3 2 AC 1 bq24023DRC bq24024DRC 6 7 8 ISET1 ISET2 CE 9 10 TTE OUT 6 5 4 3 2 6 7 8 6 9 10 TS OUT DRC PACKAGE (TOP VIEW) AC VSS STAT2 STAT1 USB 1 5 bq24026DRC ISET1 ISET2 TE 8 ISET1 ISET2 TTE DRC PACKAGE (TOP VIEW) VSS STAT2 STAT1 USB 7 4 3 AC 2 1 9 10 CE OUT bq24027DRC 9 TS 10 OUT 6 7 8 ISET1 ISET2 PG Submit Documentation Feedback bq24020,, bq24022,, bq24023 bq24024, bq24025, bq24026 bq24027 www.ti.com SLUS549D – DECEMBER 2002 – REVISED MARCH 2006 Terminal Functions TERMINAL NAME I/O bq24020 bq24022 bq24023 bq24024 bq24026 bq24025 bq24027 DESCRIPTION AC 1 1 1 1 1 I AC charge input voltage CE 8 9 8 - - I Charge enable input (active low) ISET1 6 6 6 6 6 I Charge current set point for AC input and precharge and taper set point for both AC and USB ISET2 7 7 7 7 7 I Charge current set point for USB port (high=500 mA, low=100 mA, hi-z = disable USB charge) OUT 10 10 10 10 10 O Charge current output PG - 8 - - - O powergood status output (active low) STAT1 3 3 3 3 3 O Charge status output 1 (open-drain) STAT2 4 4 4 4 4 O Charge status output 2 (open-drain) TE - - - - 8 I Timer enable input (active low) TS 9 - - 9 9 I Temperature sense input TTE - - 9 8 - I Timer and termination enable input (active low) USB 2 2 2 2 2 I USB charge input voltage VSS 5 5 5 5 5 - Ground input - There is an internal electrical connection between the exposed thermal pad and VSS pin of the device. The exposed thermal pad must be connected to the same potential as the VSS pin on the printed circuit board. Do not use the thermal pad as the primary ground input for the device. VSS pin must be connected to ground at all times Exposed Thermal Pad pad pad pad pad pad Submit Documentation Feedback 7 bq24020,, bq24022,, bq24023 bq24024, bq24025, bq24026 bq24027 www.ti.com SLUS549D – DECEMBER 2002 – REVISED MARCH 2006 FUNCTIONAL BLOCK DIAGRAM AC USB VI(AC) AC VI(OUT) VI(REG) VI(USB) VI(OUT) + VI(ISET) sensefet VI(SET) REF BIAS AND UVLO OUT ISET1 + USB AC/USB V(SET) VI(ISET-USB) CHG ENABLE AC/USB sensefet VO(REG) sensefet UVLO V(HTF) VI(ISET-USB) 100 mA/500 mA * I(TS) SUSPEND THERMAL SHUTDOWN TS AC/USB CHG ENABLE * V(LTF) 500 mA/ 100 mA CE TTE OR TE VI(OUT) VI(AC) * SLEEP (AC) VI(OUT) * SLEEP (USB) VI(USB) VO(REG) VI(OUT) RECHARGE * VI(OUT) VBAT CHARGE CONTROL, TIMER, AND DISPLAY LOGIC PRECHARGE * ISET1 PRECHARGE (C/10) 500 mA/ 100 mA ISET2 USB CHARGE PG VI(SET) VI(SET) VI(SET) * t(TAPER) TIMER TAPER STAT1 TERM * STAT2 VSS * SIGNAL DEGLITCHED 8 Submit Documentation Feedback UDG−02185 bq24020,, bq24022,, bq24023 bq24024, bq24025, bq24026 bq24027 www.ti.com SLUS549D – DECEMBER 2002 – REVISED MARCH 2006 TYPICAL CHARACTERISTICS AC DROPOUT VOLTAGE vs JUNCTION TEMPERATURE 450 IO(OUT) = 1000 mA 400 Dropout Voltage − mV 350 IO(OUT) = 750 mA 300 250 IO(OUT) = 500 mA 200 150 IO(OUT) = 250 mA 100 50 0 0 50 100 TJ − Junction Temperature − _C 150 Figure 1. The bqTINY-II supports a precision Li-Ion, Li-pol charging system suitable for single-cell packs. Figure 3 shows a typical charge profile, application circuit and Figure 4 shows an operational flow chart. Regulation Voltage Pre-Conditioning Phase Voltage Regulation and Charge Termination Phase Current Regulation Phase Regulation Current Charge Voltage Minimum Charge Voltage Charge Complete Charge Current Pre-Conditioning and Taper Detect t(PRECHG) t(CHG) Figure 2. Typical Charging Profile Submit Documentation Feedback 9 bq24020,, bq24022,, bq24023 bq24024, bq24025, bq24026 bq24027 www.ti.com SLUS549D – DECEMBER 2002 – REVISED MARCH 2006 FUNCTIONAL DESCRIPTION AC ADAPTER VDC bq24023DRC 1 AC 0.1 µF GND D+ D− VBUS PACK+ OUT 10 SYSTEM + PACK− 2 USB TTE 9 3 STAT1 CE 8 4 STAT2 ISET2 7 5 VSS SYSTEM INTERFACE GND USB PORT ISET1 6 RSET UDG−02184 Figure 3. Typical Application Circuit 10 Submit Documentation Feedback bq24020,, bq24022,, bq24023 bq24024, bq24025, bq24026 bq24027 www.ti.com SLUS549D – DECEMBER 2002 – REVISED MARCH 2006 FUNCTIONAL DESCRIPTION (continued) POR SLEEP MODE Vcc > VI(OUT) checked at all times No Indicate SLEEP MODE Yes VI(OUT)<V(LOWV) Regulate IO(PRECHG) Reset and Start t (PRECHG) timer Yes Indicate ChargeIn-Progress No Reset all timers, Start t (CHG) timer Regulate Current or Voltage Indicate ChargeIn-Progress No VI(OUT)<V(LOWV) Yes Yes t(PRECHG) Expired? No t (CHG) Expired? Yes No Yes Yes Fault Condition VI(OUT) <V(LOWV) Indicate Fault No I(TERM) detection? Yes No t(TAPER) Expired? VI(OUT)> V(RCH)? No No (1) I(TAPER) detection? Enable I (FAULT) current Yes No No Yes Yes VI(OUT) > V(RCH)? Turn off charge Yes Yes Indicate DONE No Disable I(FAULT) current VI(OUT) < V(RCH) ? (1) Submit Documentation Feedback t(TAPER) does not apply to bq24026/7 11 bq24020,, bq24022,, bq24023 bq24024, bq24025, bq24026 bq24027 www.ti.com SLUS549D – DECEMBER 2002 – REVISED MARCH 2006 FUNCTIONAL DESCRIPTION (continued) Figure 4. Operational Flow Chart AUTONOMOUS POWER SOURCE SELECTION As default, the bqTINY-II attempts to charge from the AC input. If AC input is not present, the USB is selected. If both inputs are available, the AC adapter has the priority. See for details. AC > BATTERY AC MODE USB MODE AC < BATTERY USB > BATTERY UDG−02187 Figure 5. Typical Charging Profile TEMPERATURE QUALIFICATION (bq24020, bq24024, bq24025, and bq24026 only) The bqTINY-II continuously monitors battery temperature by measuring the voltage between the TS and VSS pins. An internal current source provides the bias for common 10-kΩ negative-temperature coefficient thermistors (NTC) (see Figure 6). The device compares the voltage on the TS pin with the internal V(LTF) and V(HTF) thresholds to determine if charging is allowed. If a temperature outside the V(LTF) and V(HTF) thresholds is detected, the device immediately suspends the charge by turning off the power FET and holding the timer value (i.e. timers are NOT reset). Charge is resumed when the temperature returns within the normal range. The allowed temperature range for a 103AT-type thermistor is 0°C to 45°C. However the user may modify these thresholds by adding two external resistors. See Figure 7. BATTERY PRE-CONDITIONING If the battery voltage falls below the V(LOWV) threshold during a charge cycle, the bqTINY-II applies a precharge current, IO(PRECHG), to the battery. This feature revives deeply discharged cells. The resistor connected between the ISET1 and VSS, RSET, determines the precharge rate. The V(PRECHG) and K(SET) parameters are specified in the specifications table. Note that this applies to both AC and USB charging. V (PRECGH) K (SET) I O (PRECHG) RSET (1) The bqTINY-II activates a safety timer, t(PRECHG), during the conditioning phase. If V(LOWV) threshold is not reached within the timer period, the bqTINY-II turns off the charger and asserts a FAULT code on the STATx pins. Please refer to the TIMER FAULT RECOVERY section for additional details. PACK+ bqTINYII TS LTF HTF 9 VLTF TEMP BATTERY PACK VHTF RT1 9 LTF VLTF RT2 TEMP NTC BATTERY PACK VHTF HTF Figure 6. Temperature Sensing Configuration PACK− TS NTC UDG−02188 UDG−02186 12 + ITS PACK− ITS PACK+ bqTINYII + Figure 7. Temperature Sensing Thresholds Submit Documentation Feedback bq24020,, bq24022,, bq24023 bq24024, bq24025, bq24026 bq24027 www.ti.com SLUS549D – DECEMBER 2002 – REVISED MARCH 2006 FUNCTIONAL DESCRIPTION (continued) BATTERY CHARGE CURRENT The bqTINY-II offers on-chip current regulation with a programmable set point. The resistor connected between the ISET1 and VSS, RSET, determines the AC charge rate. The V(SET) and K(SET) parameters are specified in the specifications table. IO(OUT) + ǒK(SET) Ǔ V(SET) RSET (2) When charging from a USB port, the host controller has the option of selecting either a 100-mA or a 500-mA charge rate using the ISET2 pin. A low-level signal sets the current at 100 mA, and a high-level signal sets the current at 500 mA. A high-Z input disables USB charging BATTERY VOLTAGE REGULATION The voltage regulation feedback is through the OUT pin. This input is tied directly to the positive side of the battery pack. The bqTINY-II monitors the battery-pack voltage between the OUT and VSS pins. When the battery voltage rises to the VO(REG) threshold, the voltage-regulation phase begins and the charging current begins to taper down. As a safety backup, the bqTINY-II also monitors the charge time. If the charge is not terminated within the time period specified by t(CHG), the bqTINY-II turns off the charger and asserts a FAULT code on the STATx pins. Please refer to the TIMER FAULT RECOVERY section for additional details. CHARGE TAPER DETECTION, TERMINATION AND RECHARGE The bqTINY-II monitors the charging current during the voltage-regulation phase. When the taper threshold, I(TAPER), is detected, the bqTINY-II initiates the taper timer, t(TAPER). Charge is terminated after the timer expires. The resistor connected between the ISET1 and VSS, RSET, determines the taper detection level. The V(TAPER) and K(SET) parameters are specified in the specifications table. Note that this applies to both AC and USB charging. V(TAPER) K(SET) I (TAPER) + RSET (3) The bqTINY-II resets the taper timer if the charge current rises above the taper threshold, I(TAPER). In addition to taper-current detection, the bqTINY-II terminates charge if the charge current falls below the I(TERM) threshold. This feature allows quick recognition of a battery-removal condition, or insertion of a fully charged battery. Note that the charge timer and taper timer are bypassed for this feature. The resistor connected between the ISET1 and VSS, RSET, determines the taper detection level. The V(TERM) and K(SET) parameters are specified in the specifications table. Note that this applies to both AC and USB charging. V(TERM) K(SET) I (TERM) + R SET (4) After charge termination, the bqTINY-II re-starts the charge when the voltage on the OUT pin falls below the V(RCH) threshold. This feature keeps the battery at full capacity at all times. Note ON bq24026 AND bq24027 The bq24026 and bq24027 monitor the charging current during the voltage-regulation phase. Once the taper threshold, I(TAPER), is detected, the bq24026/27 terminates the charge. There is no taper timer (t(TAPER)) for this version. The resistor connected between the ISET1 and VSS, RSET, determines the taper-detect level for AC input. For USB charge, taper level is fixed at 10% of the 100- or 500-mA charge rate. Also note that there is I(TERM) detection in the bq24026 and the bq24027. SLEEP MODE The bqTINY-II enters low-power sleep mode if both AC and USB are removed from the circuit. This feature prevents draining the battery in the absence of input supply. Submit Documentation Feedback 13 bq24020,, bq24022,, bq24023 bq24024, bq24025, bq24026 bq24027 www.ti.com SLUS549D – DECEMBER 2002 – REVISED MARCH 2006 FUNCTIONAL DESCRIPTION (continued) CHARGE STATUS OUTPUTS The open-drain STAT1 and STAT2 outputs indicate various charger operations as shown in the following table. These status pins can be used to drive LEDs or communicate to the host processor. Note that OFF indicates the open-drain transistor is turned off. Table 1. Status Pins Summary (1) CHARGE STATE STAT1 STAT2 Precharge in progress ON ON Fast charge in progress ON OFF Charge done OFF ON Charge suspend (temperature) OFF OFF Timer fault OFF OFF Sleep mode OFF OFF (1) OFF means the open-drain output transistor on the STAT1 and STAT2 pins is in an off state. PG OUTPUT The open-drain PG (power Good) indicates when the AC adapter is present. The output turns ON when a valid voltage is detected. This output is turned off in the sleep mode. The PG pin can be used to drive an LED or to communicate to the host processor. CE INPUT (CHARGE ENABLE) The CE digital input is used to disable or enable the charge process. A low-level signal on this pin enables the charge. A high-level signal disables the charge, and places the device in a low-power mode. A high-to-low transition on this pin also resets all timers and timer fault conditions. Note that this applies to both AC and USB charging. TTE INPUT (TIMER AND TERMINATION ENABLE) The TTE digital input is used to disable or enable the fast-charge timer and charge-taper detection. A low-level signal on this pin enables the fast-charge timer and taper timer, and a high-level signal disables this feature. Note that this applies to both AC and USB charging. THERMAL SHUTDOWN AND PROTECTION The bqTINY-II monitors the junction temperature, TJ, and suspends charging if TJ exceeds T(SHTDWN). Charging resumes when TJ falls approximately 15°C below T(SHTDWN). TE INPUT (TIMER ENABLED) The TE digital input is used to disable or enable the fast-charge timer. A low-level signal on this pin enables the fast-charge timer and a high-level signal disables this feature. Note that this applies to both AC and USB charging. 14 Submit Documentation Feedback bq24020,, bq24022,, bq24023 bq24024, bq24025, bq24026 bq24027 www.ti.com SLUS549D – DECEMBER 2002 – REVISED MARCH 2006 TIMER FAULT RECOVERY As shown in Figure 4, the bqTINY-II provides a recovery method to deal with timer-fault conditions. The following discussion summarizes this method: Condition #1: The charge voltage is above the recharge threshold (V(RCH)), and a timeout fault occurs Recovery method: bqTINY-II waits for the battery voltage to fall below the recharge threshold. This could happen as a result of a load on the battery, self-discharge or battery removal. When the battery voltage falls below the recharge threshold, the bqTINY-II clears the fault and starts a new charge cycle. Toggling POR, CE, or TTE also clears the fault. Condition #2: The charge voltage is below the recharge threshold (V(RCH)), and a timeout fault occurs Recovery method: In this scenario, the bqTINY-II applies the I(FAULT) current. This small current is used to detect a battery-removal condition and remains on as long as the battery voltage stays below the recharge threshold. If the battery voltage goes above the recharge threshold, then the bqTINY-II disables the I(FAULT) current and executes the recovery method described for condition #1. When the battery voltage falls below the recharge threshold, the bqTINY-II clears the fault and starts a new charge cycle. Toggling POR, CE, or TTE also clears the fault. APPLICATION INFORMATION THERMAL CONSIDERATIONS The bqTINY-II is packaged in a thermally enhanced MLP package. The package includes a thermal pad to provide an effective thermal contact between the device and the printed circuit board (PCB). Full PCB design guidelines for this package are provided in the application note entitled, QFN/SON PCB Attachment Application Note (TI Literature Number SLUA271). The most common measure of package thermal performance is thermal impedance (θJA) measured (or modeled) from the device junction to the air surrounding the package surface (ambient). The mathematical expression for θJA is: T * TA q JA + J P (5) Where: • • • TJ = device junction temperature TA = ambient temperature P = device power dissipation Factors that can greatly influence the measurement and calculation of θJA include: • whether or not the device is board mounted • trace size, composition, thickness, and geometry • orientation of the device (horizontal or vertical) • volume of the ambient air surrounding the device under test and airflow_lus549 • whether other surfaces are in close proximity to the device being tested The device power dissipation, P, is a function of the charge rate and the voltage drop across the internal power FET. It can be calculated from the following equation: ǒ Ǔ P + V IN * V I(BAT) I O(OUT) (6) Due to the charge profile of Li-xx batteries, the maximum power dissipation is typically seen at the beginning of the charge cycle when the battery voltage is at its lowest. See Figure 2. PCB LAYOUT CONSIDERATIONS It is important to pay special attention to the PCB layout. The following provides some guidelines: Submit Documentation Feedback 15 bq24020,, bq24022,, bq24023 bq24024, bq24025, bq24026 bq24027 www.ti.com SLUS549D – DECEMBER 2002 – REVISED MARCH 2006 APPLICATION INFORMATION (continued) • • • • • 16 To obtain optimal performance, the decoupling capacitor from VCC to VSS and the output filter capacitors from OUT to VSS should be placed as close as possible to the bqTINY, with short trace runs to both signal and VSS pins. All low-current VSS connections should be kept separate from the high-current charge or discharge paths from the battery. Use a single-point ground technique incorporating both the small-signal ground path and the power-ground path. The BAT pin is the voltage feedback to the device. It should be connected with its trace as close to the battery pack as possible. The high-current charge paths into IN and from the OUT pins must be sized appropriately for the maximum charge current in order to avoid voltage drops in these traces. The bqTINY-II is packaged in a thermally-enhanced MLP package. The package includes a thermal pad to provide an effective thermal contact between the device and the printed circuit board (PCB). Full PCB design guidelines for this package are provided in the application note entitled: QFN/SON PCB Attachment Application Note (TI Literature No. SLUA271). Submit Documentation Feedback PACKAGE OPTION ADDENDUM www.ti.com 6-Dec-2006 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty BQ24020DRCR ACTIVE SON DRC 10 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR BQ24020DRCRG4 ACTIVE SON DRC 10 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR BQ24022DRCR ACTIVE SON DRC 10 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR BQ24022DRCRG4 ACTIVE SON DRC 10 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR BQ24023DRCR ACTIVE SON DRC 10 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR BQ24023DRCRG4 ACTIVE SON DRC 10 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR BQ24024DRCR ACTIVE SON DRC 10 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR BQ24024DRCRG4 ACTIVE SON DRC 10 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR BQ24025DRCR ACTIVE SON DRC 10 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR BQ24025DRCRG4 ACTIVE SON DRC 10 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR BQ24026DRCR ACTIVE SON DRC 10 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR BQ24026DRCRG4 ACTIVE SON DRC 10 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR BQ24027DRCR ACTIVE SON DRC 10 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR BQ24027DRCRG4 ACTIVE SON DRC 10 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR BQ24027DRCT ACTIVE SON DRC 10 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR BQ24027DRCTG4 ACTIVE SON DRC 10 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 6-Dec-2006 (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Low Power Wireless www.ti.com/lpw Telephony www.ti.com/telephony Mailing Address: Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright © 2007, Texas Instruments Incorporated