STMICROELECTRONICS L6563H

L6563H
High voltage start-up transition-mode PFC
Features
■
On-board 700 V start-up source
■
Tracking boost function
■
Fast “bidirectional” input voltage feedforward
(1/V2 correction)
■
Interface for cascaded converter's PWM
controller
■
Remote ON/OFF control
■
Accurate adjustable output overvoltage
protection
■
Protection against feedback loop
disconnection (latched shutdown)
■
Inductor saturation protection
■
Low (≤ 100 µA) start-up current
■
6 mA max. operating bias current
■
1% (@ TJ = 25 °C) internal reference voltage
■
-600/+800 mA totem pole gate driver with
active pull-down during UVLO
SO-16
Applications
PFC pre-regulators for:
■
Hi-end AC-DC adapter/charger
■
IEC61000-3-2 or JEITA-MITI compliant SMPS,
in excess of 400 W
Block diagram
3:0B6723
581
9
9
9
9
212))&RQWURO
=&'
'LVDEOH
293
9
9
9ROWDJH
UHIHUHQFHV
75$&.,1*
%2267
&855(17
0,5525
%8))(5
9
08/7
67$57(5
6WDUWHU
2))
',6$%/(
IURP
9))
4
4
293
212))&RQWURO
/(%
6
/B293
5
89/2
9ELDV
(UURU$PSOLILHU
/B293
,GHDOUHFWLILHU
*1'
*'
'LVDEOH
9
4
5
89/2
6
P9
,19
89/2
/B293
&203
92/7$*(
5(*8/$725
,QWHUQDO6XSSO\%XV
7%2
,FKDUJH
9
9
9FF
=HUR&XUUHQW
'HWHFWRU
3)&B2.
+96
«
Figure 1.
SO16
9
08/7,3/,(5
0$,16'523
'(7(&725
9
3:0B
/$7&+
&6
'LVDEOH
9))
February 2010
!-V
Doc ID 16047 Rev 2
1/48
www.st.com
48
Contents
L6563H
Contents
1
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2
Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3
Pin connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5
Typical electrical performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6
Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6.1
Overvoltage protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6.2
Feedback failure protection (FFP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
6.3
Voltage feedforward . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
6.4
THD optimizer circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
6.5
Tracking boost function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.6
Inductor saturation detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
6.7
Power management/housekeeping functions . . . . . . . . . . . . . . . . . . . . . . 32
6.8
High-voltage start-up generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
7
Application examples and ideas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
8
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
9
Ordering codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
10
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
2/48
Doc ID 16047 Rev 2
L6563H
List of table
List of table
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Thermal data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Summary of L6563H idle states . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
SO16 mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Doc ID 16047 Rev 2
3/48
List of figure
L6563H
List of figure
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
Figure 14.
Figure 15.
Figure 16.
Figure 17.
Figure 18.
Figure 19.
Figure 20.
Figure 21.
Figure 22.
Figure 23.
Figure 24.
Figure 25.
Figure 26.
Figure 27.
Figure 28.
Figure 29.
Figure 30.
Figure 31.
Figure 32.
Figure 33.
Figure 34.
Figure 35.
Figure 36.
Figure 37.
Figure 38.
Figure 39.
Figure 40.
Figure 41.
Figure 42.
Figure 43.
Figure 44.
Figure 45.
Figure 46.
Figure 47.
Figure 48.
4/48
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Pin connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Typical system block diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
IC consumption vs VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
IC consumption vs TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Vcc Zener voltage vs TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Start-up and UVLO vs TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Feedback reference vs TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
E/A output clamp levels vs TJ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
UVLO saturation vs TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
OVP levels vs TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Inductor saturation threshold vs TJ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Vcs clamp vs TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
ZCD sink/source capability vs TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
ZCD clamp level vs TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
TBO clamp vs TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
VVFF - VTBO dropout vs TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
IINV - ITBO current mismatch vs TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
IINV - ITBO mismatch vs ITBO current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
R discharge vs TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Line drop detection threshold vs TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
VMULTpk - VVFF dropout vs TJ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
PFC_OK threshold vs TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
PFC_OK FFD threshold vs TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
PWM_LATCH high saturation vs TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
RUN threshold vs TJ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
PWM_STOP low saturation vs TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Multiplier characteristics @ VFF = 1 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Multiplier characteristics @ VFF = 3 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Multiplier gain vs TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Gate drive clamp vs TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Gate drive output saturation vs TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Delay to output vs TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Start-up timer period vs TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
HV start voltage vs TJ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
VCC restart voltage vs TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
HV breakdown voltage vs TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Output voltage setting, OVP and FFP functions: internal block diagram . . . . . . . . . . . . . . 24
Voltage feedforward: squarer-divider (1/V2) block diagram and transfer characteristic . . 26
RFF·CFF as a function of 3rd harmonic distortion introduced in the input current . . . . . . . 27
THD optimizer circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
THD optimization: standard TM PFC controller (left side) and L6563H (right side) . . . . . . 28
Tracking boost block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Tracking output voltage vs Input voltage characteristic with TBO . . . . . . . . . . . . . . . . . . . 31
Effect of boost inductor saturation on the MOSFET current and detection method . . . . . . 31
Interface circuits that let dc-dc converter's controller IC drive L6563H in burst mode . . . . 32
Interface circuits that let the L6563H switch on or off a PWM controller. . . . . . . . . . . . . . . 33
Interface circuits for power up sequencing when dc-dc has the SS function . . . . . . . . . . . 33
Doc ID 16047 Rev 2
L6563H
Figure 49.
Figure 50.
Figure 51.
Figure 52.
Figure 53.
Figure 54.
Figure 55.
Figure 56.
Figure 57.
Figure 58.
Figure 59.
Figure 60.
Figure 61.
Figure 62.
Figure 63.
List of figure
Interface circuits for actual power-up sequencing (master PFC) . . . . . . . . . . . . . . . . . . . . 34
Brownout protection (master PFC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
High-voltage start-up generator: internal schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Timing diagram: normal power-up and power-down sequences . . . . . . . . . . . . . . . . . . . . 36
High-voltage start-up behaviour during latch-off protection . . . . . . . . . . . . . . . . . . . . . . . . 37
High-voltage start-up managing the dc-dc output short-circuit . . . . . . . . . . . . . . . . . . . . . . 37
Demonstration board EVL6563H-100W, wide-range mains: electrical schematic . . . . . . . 39
L6563H 100 W TM PFC evaluation board: compliance to EN61000-3-2 standard . . . . . . 40
L6563H 100 W TM PFC evaluation board: compliance to JEITA-MITI standard . . . . . . . . 40
L6563H 100 W TM PFC evaluation board: input current waveform @230-50 Hz - 100 W 40
L6563H 100W TM PFC evaluation board: input current waveform @100-50 Hz - 100 W 40
Application board 90W-19V adapter with L6563H, L6599A, SRK2000 . . . . . . . . . . . . . . . 41
Application board 130 W-12 V adapter with L6563H, L6599A, SRK2000 . . . . . . . . . . . . . 42
Demonstration board EVL6563H-650W wide-range mains: electrical schematics. . . . . . . 43
SO16 mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Doc ID 16047 Rev 2
5/48
Description
1
L6563H
Description
The L6563H is a current-mode PFC controller operating in transition mode (TM) which
embeds the same features existing in the L6563S with the addition of a high voltage start-up
source. These functions make the IC especially suitable for applications that have to be
compliant with energy saving regulations and where the PFC pre-regulator works as the
master stage.
The highly linear multiplier, along with a special correction circuit that reduces crossover
distortion of the mains current, allows wide-range-mains operation with an extremely low
THD even over a large load range.
The output voltage is controlled by means of a voltage-mode error amplifier and an accurate
(1% @Tj = 25 °C) internal voltage reference. Loop's stability is optimized by the voltage
feedforward function (1/V2 correction), which in this IC uses a proprietary technique that
considerably improves line transient response as well in case of mains both drops and
surges (“bidirectional”).
Additionally, the IC provides the option for tracking boost operation, i.e. the output voltage is
changed tracking the mains voltage.
The device includes disable functions suitable for remote ON/OFF control too.
In addition to an over voltage protection able to keep the output voltage under control during
transient conditions, the IC is provided also with a protection against feedback loop failures
or erroneous settings. Other on-board protection functions allow that brownout conditions
and boost inductor saturation can be safely handled.
An interface with the PWM controller of the DC-DC converter supplied by the PFC preregulator is provided: the purpose is to stop the operation of the converter in case of
anomalous conditions for the PFC stage (feedback loop failure, boost inductor's core
saturation, etc.) and to handle the PFC stage in case of light load for the DC-DC converter,
to make it easier to comply with energy saving regulations (Blue Angel, EnergyStar,
Energy2000, etc.).
The totem-pole output stage, capable of 600 mA source and 800 mA sink current, is suitable
for big MOSFET or IGBT drive. This, combined with the other features and the possibility to
operate with ST's proprietary fixed-off-time control, makes the device an excellent solution
for SMPS up to 400 W that need to be compliant with EN61000-3-2 and JEITA-MITI
standards.
6/48
Doc ID 16047 Rev 2
L6563H
Maximum ratings
2
Maximum ratings
2.1
Absolute maximum ratings
Table 1.
Symbol
Pin
VHVS
9
IHVS
Vcc
-----
2.2
Absolute maximum ratings
Value
Unit
Voltage range (referred to ground)
-0.3 to 700
V
9
Output current
Self-limited IHVS
16
IC supply voltage (Icc = 20 mA)
self-limited
V
Max. pin voltage (Ipin =1 mA)
Self-limited
V
-0.3 to 8
V
3
mA
1, 3, 7
Parameter
2, 4 to 6, 8, 11, 12 Analog inputs and outputs
IPWM_STOP
11
Max. sink current
IZCD
13
Zero current detector max. current
-10 (source)
mA
10 (sink)
Thermal data
Table 2.
Thermal data
Symbol
Parameter
Value
Unit
RthJA
Max. thermal resistance, junction-to-ambient
120
°C/W
Ptot
Power dissipation @TA = 50 °C
0.75
W
Junction temperature operating range
-40 to 150
°C
Storage temperature
-55 to 150
°C
TJ
Tstg
Doc ID 16047 Rev 2
7/48
Pin connection
3
L6563H
Pin connection
Figure 2.
Pin connection
6CC
#/-0 '$
).6
-5,4
'.$
#3
:#$
6&&
25.
4"/
07-?34/0
0&#?/+
.#
07-?,!4#(
(63
!-V
Table 3.
n°
Pin description
Name
Function
INV
Inverting input of the error amplifier. The information on the output voltage of the PFC preregulator is fed into the pin through a resistor divider.
The pin normally features high impedance but, if the tracking boost function is used, an internal
current generator programmed by TBO (pin 6) is activated. It sinks current from the pin to
change the output voltage so that it tracks the mains voltage.
2
COMP
Output of the error amplifier. A compensation network is placed between this pin and INV (pin
1) to achieve stability of the voltage control loop and ensure high power factor and low THD.
To avoid uncontrolled rise of the output voltage at zero load, when the voltage on the pin falls
below 2.4 V the gate driver output is inhibited (burst-mode operation).
3
MULT
Mains input to the multiplier. This pin is connected to the rectified mains voltage via a resistor
divider and provides the sinusoidal reference to the current loop. The voltage on this pin is used
also to derive the information on the RMS mains voltage.
CS
Input to the PWM comparator. The current flowing in the MOSFET is sensed through a resistor,
the resulting voltage is applied to this pin and compared with an internal reference to determine
MOSFET’s turn-off.
A second comparison level at 1.7 V detects abnormal currents (e.g. due to boost inductor
saturation) and, on this occurrence, activates a safety procedure that temporarily stops the
converter and limits the stress of the power components.
VFF
Second input to the multiplier for 1/V2 function. A capacitor and a parallel resistor must be
connected from the pin to GND. They complete the internal peak-holding circuit that derives the
information on the RMS mains voltage. The voltage at this pin, a dc level equal to the peak
voltage on pin MULT (3), compensates the control loop gain dependence on the mains voltage.
Never connect the pin directly to GND but with a resistor ranging from 100 kΩ (minimum) to 2 M
Ω (maximum).
TBO
Tracking boost function. This pin provides a buffered VFF voltage. A resistor connected
between this pin and GND defines a current that is sunk from pin INV (1). In this way, the output
voltage is changed proportionally to the mains voltage (tracking boost). If this function is not
used leave this pin open.
1
4
5
6
8/48
Doc ID 16047 Rev 2
L6563H
Pin connection
Table 3.
n°
7
Pin description (continued)
Name
Function
PFC_OK
PFC pre-regulator output voltage monitoring/disable function. This pin senses the output
voltage of the PFC pre-regulator through a resistor divider and is used for protection purposes.
If the voltage on the pin exceeds 2.5 V the IC stops switching and restarts as the voltage on the
pin falls below 2.4 V. However, if the voltage of the pin INV falls 40 mV below that one of the pin
PFC_OK, a feedback failure is assumed. In this case the device is latched off and the
PWM_LATCH (8) pin is asserted high. Normal operation can be resumed only by cycling Vcc
bringing its value lower than 6V before to move up to Turn on threshold.
If the voltage on this pin is brought below 0.23 V the IC is shut down. To restart the IC the
voltage on the pin must go above 0.27 V. This can be used as a remote on/off control input.
Output pin for fault signaling. During normal operation this pin features high impedance. If a
feedback failure is detected (PFC_OK > 2.5 V and INV+40 mV < PFC_OK) the pin is asserted
8 PWM_LATCH high. Normally, this pin is used to stop the operation of the dc-dc converter supplied by the PFC
pre-regulator by invoking a latched disable of its PWM controller. If not used, the pin is left
floating.
9
HVS
High-voltage start-up. The pin, able to withstand 700 V, is to be tied directly to the rectified
mains voltage. A 1 mA internal current source charges the capacitor connected between pin
Vcc (16) and pin GND (14) until the voltage on the pin Vcc reaches the start-up threshold, then
it is shut down. Normally, the generator is re-enabled when the Vcc voltage falls below 6 V to
ensure a low power throughput during short circuit. Otherwise, when a latched protection is
tripped the generator is re-enabled as Vcc reaches the UVLO threshold to keep the latch
supplied.
10
N.C.
Not internally connected. Provision for clearance on the PCB to meet safety requirements.
Output pin for fault signaling. During normal operation this pin features high impedance. If the
IC is disabled by a voltage below 0.8 V on pin RUN (12) the voltage on the pin is pulled to
ground. Normally, this pin is used to temporarily stop the operation of the dc-dc converter
11 PWM_STOP
supplied by the PFC pre-regulator by disabling its PWM controller. A typical usage of this
function is brownout protection in systems where the PFC pre-regulator is the master stage. If
not used, the pin is left floating.
12
RUN
Remote ON/OFF control. A voltage below 0.8 V shuts down (not latched) the IC and brings its
consumption to a considerably lower level. PWM_STOP is asserted low. The IC restarts as the
voltage at the pin goes above 0.88V. Connect this pin to pin VFF (5) either directly or through a
resistor divider to use this function as brownout (AC mains undervoltage) protection.
13
ZCD
Boost inductor’s demagnetization sensing input for transition-mode operation. A negative-going
edge triggers MOSFET’s turn-on.
14
GND
Ground. Current return for both the signal part of the IC and the gate driver.
15
GD
Gate driver output. The totem pole output stage is able to drive power MOSFET’s and IGBT’s
with a peak current of 600 mA source and 800 mA sink. The high-level voltage of this pin is
clamped at about 12 V to avoid excessive gate voltages.
16
Vcc
Supply voltage of both the signal part of the IC and the gate driver. Sometimes a small bypass
capacitor (0.1 µF typ.) to GND might be useful to get a clean bias voltage for the signal part of
the IC.
Doc ID 16047 Rev 2
9/48
Pin connection
L6563H
Figure 3.
Typical system block diagram
0&#02%2%'5,!4/2
$#$##/.6%24%2
6OUTDC
6INAC
07-ISTURNEDOFFINCASEOF0&#gS
ANOMALOUSOPERATIONFORSAFETY
,(
07-OR
2ESONANT
#/.42/,,%2
0&#CANBETURNEDOFFATLIGHT
LOADTOEASECOMPLIANCEWITH
ENERGYSAVINGREGULATIONS
!-V
10/48
Doc ID 16047 Rev 2
L6563H
4
Electrical characteristics
Electrical characteristics
TJ = -25 to 125 °C, VCC = 12 V, CO = 1 nF between pin GD and GND, CFF = 1 µF and
RFF = 1 MΩ between pin VFF and GND; unless otherwise specified
Table 4.
Electrical characteristics
Symbol
Parameter
Test condition
Min. Typ. Max. Unit
Supply voltage
Vcc
Operating range
After turn-on
VccOn
Turn-on threshold
(1)
11
VccOff
Turn-off threshold
(1)
Vcc for resuming from latch
OVP latched
Vccrestart
Hys
Hysteresis
VZ
Zener voltage
10.3
22.5
V
12
13
V
8.7
9.5
10.3
V
5
6
7
V
2.7
V
25
28
V
2.3
Icc = 20 mA
22.5
Supply current
Istart-up
Iq
ICC
Iqdis
Iq
Start-up current
Before turn-on, Vcc = 10 V
90
150
µA
Quiescent current
After turn-on, VMULT = 1 V
4
5
mA
Operating supply current
@ 70 kHz
5
6.0
mA
VPFC_OK > VPFC_OK_S AND
VINV < VPFC_OK – VFFD
180
280
µA
VPFC_OK < VPFC_OK_D OR
VRUN < VDIS
1.5
2.2
mA
VPFC_OK > VPFC_OK_S OR
VCOMP < 2.3 V
2.2
3
mA
Idle state quiescent current
Quiescent current
High-voltage start-up generator
Breakdown voltage
IHV < 100 µA
700
Start voltage
IVcc < 100 µA
65
Icharge
Vcc charge current
VHV > VHvstart, Vcc > 3 V
IHV, ON
ON-state current
IHV, OFF
OFF-state leakage current
VHV
VHVstart
Vcc restart voltage
80
0.55 0.85
100
V
1
mA
VHV > VHvstart, Vcc > 3 V
1.6
VHV > VHvstart, Vcc = 0
0.8
VHV = 400 V
40
Vcc falling
VCCrestart
V
IC latched off (1)
mA
5
6
7
8.7
9.5
10.3
-0.2
-1
µA
V
Multiplier input
IMULT
Input bias current
VMULT
Linear operation range
VCLAMP
Internal clamp level
VMULT = 0 to 3 V
0 to 3
IMULT = 1 mA
Doc ID 16047 Rev 2
9
µA
V
9.5
V
11/48
Electrical characteristics
Table 4.
Electrical characteristics (continued)
Symbol
ΔVcs
ΔVMULT
KM
L6563H
Parameter
Test condition
Min. Typ. Max. Unit
Output max. slope
VMULT =0 to 0.4 V, VVFF = 0.8 V
VCOMP = Upper clamp
Gain (2)
VMULT = 1 V, VCOMP = 4 V
0.375 0.45 0.525 1/V
TJ = 25 °C
2.475
2.5 2.525
2.455
2.545
2.2
2.34
V/V
Error amplifier
VINV
IINV
Voltage feedback input threshold
10.3 V < Vcc < 22.5 V
Line regulation
Vcc = 10.3 V to 22.5 V
Input bias current
TBO open, VINV = 0 to 4 V
VINVCLAMP Internal clamp level
Gv
Voltage gain
GB
Gain-bandwidth product
ICOMP
VCOMP
(3)
V
2
5
mV
-0.2
-1
µA
IINV = 1 mA
8
9
V
Open loop
60
80
dB
1
MHz
Source current
VCOMP = 4 V, VINV = 2.4 V
2
4
mA
Sink current
VCOMP = 4 V, VINV = 2.6 V
2.5
4.5
mA
Upper clamp voltage
ISOURCE = 0.5 mA
5.7
6.2
6.7
Burst-mode voltage
(3)
2.3
2.4
2.5
Lower clamp voltage
ISINK = 0.5 mA (3)
2.1
2.25
2.4
V
Current sense comparator
ICS
Input bias current
tLEB
Leading edge blanking
100
Delay to output
td(H-L)
VCSclamp
Vcsofst
Current sense reference clamp
Current sense offset
VCS = 0
1
µA
150
250
ns
100
200
300
ns
1.0
1.08
1.16
V
VMULT = 0, VVFF = 3 V
40
70
VMULT = 3 V, VVFF = 3 V
20
VCOMP = Upper clamp,
VMULT =1 V VVFF = 1 V
mV
Boost inductor saturation detector
VCS_th
IINV
Threshold on current sense
(3)
E/A input pull-up current
After VCS > VCS_th, before restarting
1.6
1.7
1.8
V
7
10
13
µA
-0.1
-1
µA
PFC_OK functions
IPFC_OK
Input bias current
VPFC_OK = 0 to 2.6 V
VPFC_OK_C Clamp voltage
IPFC_OK = 1 mA
VPFC_OK_S OVP threshold
(1)
voltage rising
VPFC_OK_R Restart threshold after OVP
(1)
VPFC_OK_D Disable threshold
(1)
VPFC_OK_D Disable threshold
(1)
12/48
9.5
V
2.435
2.5 2.565
V
voltage falling
2.34
2.4
2.46
V
voltage falling
0.12
0.35
V
voltage falling TJ = 25 °C
0.17 0.23
0.29
V
Doc ID 16047 Rev 2
9
L6563H
Electrical characteristics
Electrical characteristics (continued)
Table 4.
Symbol
Parameter
Test condition
Min. Typ. Max. Unit
VPFC_OK_E Enable threshold
(1)
voltage rising
0.15
0.38
V
VPFC_OK_E Enable threshold
(1)
voltage rising Tj = 25 °C
0.21 0.27
0.32
V
VFFD
Feedback failure detection
threshold (VPFC_OK -VINV)
VPFC_OK = VPFC_OK_S
15
40
65
mV
VFFD
Feedback failure detection
threshold (VPFC_OK -VINV)
VPFC_OK = VPFC_OK_S
Tj = 25 °C
25
40
55
mV
Zero current detector
VZCDH
Upper clamp voltage
IZCD = 2.5 mA
5.0
5.7
VZCDL
Lower clamp voltage
IZCD = - 2.5 mA
-0.3
0
0.3
V
VZCDA
Arming voltage
(positive-going edge)
1.1
1.4
1.9
V
VZCDT
Triggering voltage
(negative-going edge)
0.5
0.7
0.9
V
IZCDb
Input bias current
1
µA
VZCD = 1 to 4.5 V
V
IZCDsrc
Source current capability
-2.5
-4
mA
IZCDsnk
Sink current capability
2.5
5
mA
Tracking boost function
ΔV
ITBO
Dropout voltage VVFF-VTBO
Linear operation
-20
20
mV
0
0.2
mA
IINV-ITBO current mismatch
ITBO = 25 µA to 0.2mA
-5.5
1.0
%
IINV-ITBO current mismatch
ITBO = 25 µA to 0.2mA
TJ = 25 °C
-4.0
+0
%
(3) V
VFF
2.9
3.1
V
VTBO = 1 V
VFF = VMULT = 0 V
2
μA
VTBOclamp Clamp voltage
ITBO_Pull
ITBO = 0.2 mA
Pull-up current
=4V
3
PWM_STOP
Ileak
High level leakage current
VPWM_STOP = Vcc
1
µA
VL
Low level
IPWM_STOP = 0.5 mA
1
V
Input bias current
VRUN = 0 to 3 V
-1
µA
VDIS
Disable threshold
(3)
voltage falling
0.745
0.8 0.855
V
VEN
Enable threshold
(3)
voltage rising
0.845 0.88 0.915
V
RUN function
IRUN
Start-up timer
tSTART_DEL Start-up delay
First cycle after wake-up
Doc ID 16047 Rev 2
25
50
75
µs
13/48
Electrical characteristics
Table 4.
Electrical characteristics (continued)
Symbol
tSTART
L6563H
Parameter
Test condition
Min. Typ. Max. Unit
75
150
300
150
300
600
Timer period
µs
Restart after VCS > VCS_th
Voltage feedforward
VVFF
Linear operation range
ΔV
Dropout VMULTpk-VVFF
0.8
3
Vcc < VccOn
800
Vcc > or = to VccOn
20
V
mV
ΔVVFF
Line drop detection threshold
Below peak value
40
70
100
mV
ΔVVFF
Line drop detection threshold
Below peak value
TJ = 25 °C
50
70
90
mV
10
12.5
Internal discharge resistor
TJ = 25 °C
7.5
RDISCH
VVFF
Linear operation range
kΩ
5
20
0.8
3
V
-1
µA
PWM_LATCH
Ileak
Low level leakage current
VPWM_LATCH = 0
VH
High level
IPWM_LATCH = -0.5 mA
4.5
V
VH
High level
IPWM_LATCH = -0.25 mA
Vcc = VccOff
2.5
V
VH
High level
IPWM_LATCH = -0.25 mA
Vcc = VccOff TJ = 25 °C
2.8
V
VOL
Output low voltage
Isink = 100 mA
VOH
Output high voltage
Isource = 5 mA
Isrcpk
Peak source current
-0.6
A
Isnkpk
Peak sink current
0.8
A
Gate driver
9.8
1.2
10.3
V
V
tf
Voltage fall time
30
60
ns
tr
Voltage rise time
45
110
ns
12
15
V
1.1
V
VOclamp
Output clamp voltage
Isource = 5 mA; Vcc = 20 V
UVLO saturation
Vcc= 0 to VCCon, Isink = 2 mA
1. Parameters tracking each other
2. The multiplier output is given by:
Vcs = VCS_Ofst + K M ⋅
(
VMULT ⋅ VCOMP − 2.5
2
V
VFF
)
3. Parameters tracking each other
14/48
0.6
Doc ID 16047 Rev 2
10
L6563H
Typical electrical performance
5
Typical electrical performance
Figure 4.
IC consumption vs VCC
Figure 5.
100
IC consumption vs TJ
10
Operating
10
Quiescent
Disabled or
during OV P
1
Co=1nF
f =70kHz
Tj = 25°C
I cc [m A]
VCC=12V
Co = 1nF
f =70kHz
I c current (m A)
1
0.1
Latched off
0.1
Before Start up
0.01
VccOFF
VccON
0.01
0. 001
0
5
10
15
20
25
-50
30
-25
0
25
50
Figure 6.
75
100
125
150
175
Tj (C)
Vcc [V ]
Vcc Zener voltage vs TJ
Figure 7.
Start-up and UVLO vs TJ
28
13
V CC-ON
12
27
11
26
VCC-OFF
V
V
10
25
9
24
8
23
7
6
22
-50
-25
0
25
50
75
100
125
150
175
-50
Tj (C)
-25
0
25
50
75
100
125
150
175
Tj (C)
Doc ID 16047 Rev 2
15/48
Typical electrical performance
Figure 8.
L6563H
Feedback reference vs TJ
Figure 9.
E/A output clamp levels vs TJ
2. 6
7
Uper Clam p
6
VCC = 12V
2.55
5
V COM P (V )
pi n INV (V )
V CC = 12V
2. 5
4
3
Lower Clamp
2
2.45
1
0
2. 4
-50
-25
0
25
50
75
Tj (C)
100
125
150
-25
0
25
50
75
100
150
175
Figure 11. OVP levels vs TJ
1
2. 5
0.9
2. 48
VCC = 0V
0.8
OV P T h
2. 46
P FC_OK l evels (V )
0.7
0.6
V
125
Tj (C)
Figure 10. UVLO saturation vs TJ
-50
175
0.5
0.4
2. 44
2. 42
2. 4
0.3
Resta rt Th
0.2
2. 38
0.1
2. 36
0
-50
-50
-25
0
25
50
75
100
125
150
175
Tj (C)
16/48
Doc ID 16047 Rev 2
-25
0
25
50
75
Tj (C)
100
125
150
175
L6563H
Typical electrical performance
Figure 12. Inductor saturation threshold vs TJ Figure 13. Vcs clamp vs TJ
1.9
1. 4
1.8
1.7
1. 3
VCSx (V )
CS pi n (V )
1.6
1.5
VCC = 12V
VCOMP =Upper clamp
1. 2
1.4
1.3
1. 1
1.2
1.1
1
-50
-25
0
25
50
75
100
125
150
175
-50
-25
0
25
50
Figure 14. ZCD sink/source capability vs TJ
100
125
150
175
Figure 15. ZCD clamp level vs TJ
8
7
Si nk curren t
6
Upper Clamp
6
4
5
2
V ZCD pin (V )
IZCDsrc (mA)
75
Tj (C)
Tj (C)
V CC = 12V
0
-2
4
VCC = 12V
Izcd =± 2.5mV
3
2
Source current
-4
1
-6
0
-8
-50
Lower Cl am p
-1
-25
0
25
50
75
100
125
150
175
-50
-25
0
25
50
75
100
125
150
175
Tj (C)
Tj (C)
Doc ID 16047 Rev 2
17/48
Typical electrical performance
L6563H
Figure 16. TBO clamp vs TJ
Figure 17. VVFF - VTBO dropout vs TJ
5
3.5
4
3
3.25
2
mV
1
V
3
0
-1
-2
2.75
-3
-4
-5
2.5
-50
-25
0
25
50
Tj (C)
75
100
125
150
Figure 18. IINV - ITBO current mismatch vs TJ
-50
175
-25
0
25
50
75
100
125
150
175
T j (C)
Figure 19. IINV - ITBO mismatch vs ITBO current
0
-1.6
VCC = 12V
-1.8
-1
100*{I(I NV )-I(TBO)}/I (TBO) [ % ]
100*{I(INV)-I(TBO)}/I(TBO) [ % ]
-0.5
I TBO = 200uA
-1.5
-2
ITBO = 25uA
-2.5
-3
-2
-2.2
-2.4
VCC = 12V
Tj = 25°C
-2.6
-2.8
-3.5
-4
-3
-50
-25
0
25
50
75
100
125
150
175
0
Tj (C)
18/48
Doc ID 16047 Rev 2
100
200
300
I(TBO)
400
500
600
L6563H
Typical electrical performance
Figure 20. R discharge vs TJ
Figure 21. Line drop detection threshold vs TJ
20
90
18
80
16
70
14
60
50
mV
kOhm
12
10
40
8
30
6
20
4
10
2
0
0
-50
-25
0
25
50
75
100
125
150
-50
175
-25
0
25
50
Figure 22. VMULTpk - VVFF dropout vs TJ
100
125
150
175
150
175
Figure 23. PFC_OK threshold vs TJ
2
0.4
1. 5
0.35
1
0.3
0. 5
0.25
Th (V )
⎯ (m V)
75
Tj (C)
Tj (C)
0
ON
0.2
-0. 5
0.15
-1
0.1
-1. 5
0.05
-2
OFF
0
-50
-25
0
25
50
75
Tj (C)
100
125
150
175
-50
Doc ID 16047 Rev 2
-25
0
25
50
Tj (C)
75
100
125
19/48
Typical electrical performance
L6563H
Figure 24. PFC_OK FFD threshold vs TJ
Figure 25. PWM_LATCH high saturation vs TJ
60
10
VCC = 12V
50
9
Isource =500uA
8
30
7
V
VFFD Th (V)
40
20
6
10
5
0
Isource =250uA
4
-50
-25
0
25
50
75
100
125
150
175
-50
-25
0
25
T j (C)
Figure 26. RUN threshold vs TJ
50
75
T j (C)
100
125
150
175
Figure 27. PWM_STOP low saturation vs TJ
0. 25
1
ON
0.2
VCC = 12V
Isink = 0. 5m A
0.8
OFF
V
V
0. 15
VCC = 12V
0.1
0.6
0. 05
0.4
0
-50
-25
0
25
50
75
100
125
150
175
-50
20/48
-25
0
25
50
75
Tj (C)
T j (C)
Doc ID 16047 Rev 2
100
125
150
175
L6563H
Typical electrical performance
Figure 28. Multiplier characteristics
@ VFF = 1 V
Figure 29. Multiplier characteristics
@ VFF = 3 V
1. 2
700
VCOMP
1. 1
V COM P
Upper voltage cl amp
1
600
Upper vo ltage
5 .5
5 .0V
0. 9
4.5 V
500
4. 0V
400
0. 8
V CS (V )
V CS (m V)
5. 5V
0. 7
0. 6
0. 5
5. 0V
4. 5V
300
3.5 V
4. 0V
0. 4
200
0. 3
3. 5V
0. 2
3.0
100
3. 0V
0. 1
2. 6V
2.6 V
0
0
0
0. 1
0.2
0. 3
0. 4
0.5
0.6
0.7
0. 8
0.9
1
1.1
0
0. 5
1
1. 5
2
V MULT (V )
VM UL T (V )
Figure 30. Multiplier gain vs TJ
2. 5
3
3. 5
Figure 31. Gate drive clamp vs TJ
0. 5
12. 9
V CC = 20V
12.85
0. 4
Gai n (1/V )
12. 8
V
VCC = 12V
VCOMP = 4V
VMULT = VFF= 1V
12.75
0. 3
12. 7
0. 2
-50
-25
0
25
50
75
100
125
150
175
12.65
-50
Tj (C)
Doc ID 16047 Rev 2
-25
0
25
50
75
Tj (C)
100
125
150
175
21/48
Typical electrical performance
L6563H
Figure 32. Gate drive output saturation vs TJ
Figure 33. Delay to output vs TJ
12
300
High level
10
250
TD(H-L) (n s)
V
8
6
200
VCC = 12V
150
4
100
Low level
2
50
0
-50
-25
0
25
50
75
100
125
150
-50
175
-25
0
25
Figure 34. Start-up timer period vs TJ
50
75
100
125
150
175
Tj (C)
Tj (C)
Figure 35. HV start voltage vs TJ
450
100
After OCP
400
80
350
300
V
Ti m e (us)
60
250
Timer
200
40
150
100
20
First Cicle
50
0
0
-50
-50
-25
0
25
50
75
100
125
150
175
Tj (C)
22/48
Doc ID 16047 Rev 2
-25
0
25
50
75
Tj (C)
100
125
150
175
L6563H
Typical electrical performance
Figure 36. VCC restart voltage vs TJ
Figure 37. HV breakdown voltage vs TJ
800
14
750
12
ICC
700
10
V
V
8
fa ll i ng
650
6
600
4
550
2
500
0
-50
-25
0
25
50
75
100
125
150
175
-50
-25
0
25
50
75
100
125
150
175
Tj (C)
T j (C)
Doc ID 16047 Rev 2
23/48
Application information
L6563H
6
Application information
6.1
Overvoltage protection
Normally, the voltage control loop keeps the output voltage Vo of the PFC pre-regulator
close to its nominal value, set by the ratio of the resistors R1 and R2 of the output divider. A
pin of the device (PFC_OK) has been dedicated to monitor the output voltage with a
separate resistor divider (R3 high, R4 low, see Figure 38). This divider is selected so that
the voltage at the pin reaches 2.5 V if the output voltage exceeds a preset value, usually
larger than the maximum Vo that can be expected.
Example: VO = 400 V, VOX = 434 V. Select: R3 = 8.8 MΩ; then: R4 = 8.8 MΩ ·2.5/(434-2.5) =
51 kΩ.
When this function is triggered, the gate drive activity is immediately stopped until the
voltage on the pin PFC_OK drops below 2.4 V. Notice that R1, R2, R3 and R4 can be
selected without any constraints. The unique criterion is that both dividers have to sink a
current from the output bus which needs to be significantly higher than the bias current of
both INV and PFC_OK pins.
Figure 38. Output voltage setting, OVP and FFP functions: internal block diagram
6OUT
2A
2
2B
$ISABLE
/60
,?/60
2
2B
&REQUENCY #/-0
COMPENSATION
M6
).6
2
6
6
0&#?/+
2A
6
6
6
%RROR!MPLIFIER
2
!-V
24/48
Doc ID 16047 Rev 2
L6563H
6.2
Application information
Feedback failure protection (FFP)
The OVP function above described handles “normal” over voltage conditions, i.e. those
resulting from an abrupt load/line change or occurring at start-up. In case the overvoltage is
generated by a feedback disconnection, for instance when the upper resistor of the output
divider (R1) fails open, an additional circuitry behind the pin PFC_OK detects the voltage
gap with respect to pin INV. If the voltage gap is greater than 40 mV and the OVP is active,
the FFP is triggered, the gate drive activity is immediately stopped, the device is shut down,
its quiescent consumption is reduced below 180 µA and the condition is latched as long as
the supply voltage of the IC is above the UVLO threshold. At the same time the pin
PWM_LATCH is asserted high. PWM_LATCH is an open source output able to deliver 2.8 V
minimum with 0.25 mA load, intended for tripping a latched shutdown function of the PWM
controller IC in the cascaded dc-dc converter, so that the entire unit is latched off. To restart
the system it is necessary to recycle the input power, so that the Vcc voltage of both the
L6563H goes below 6V and that one of the PWM controller goes below its UVLO threshold.
The pin PFC_OK doubles its function as a not-latched IC disable: a voltage below 0.23V
shutdown the IC, reducing its consumption below 2 mA. In this case both PWM_STOP and
PWM_LATCH keep their high impedance status. To restart the IC simply let the voltage at
the pin go above 0.27 V.
Note that these functions offer a complete protection against not only feedback loop failures
or erroneous settings, but also against a failure of the protection itself. Either resistor of the
PFC_OK divider failing short or open or a PFC_OK pin floating results in shutting down the
IC and stopping the pre-regulator.
6.3
Voltage feedforward
The power stage gain of PFC pre-regulators varies with the square of the RMS input
voltage. So does the crossover frequency fc of the overall open-loop gain because the gain
has a single pole characteristic. This leads to large trade-offs in the design.
For example, setting the gain of the error amplifier to get fc = 20 Hz @ 264 Vac means
having fc 4 Hz @ 88 Vac, resulting in a sluggish control dynamics. Additionally, the slow
control loop causes large transient current flow during rapid line or load changes that are
limited by the dynamics of the multiplier output. This limit is considered when selecting the
sense resistor to let the full load power pass under minimum line voltage conditions, with
some margin. But a fixed current limit allows excessive power input at high line, whereas a
fixed power limit requires the current limit to vary inversely with the line voltage.
Voltage Feedforward can compensate for the gain variation with the line voltage and allow
minimizing all of the above-mentioned issues. It consists of deriving a voltage proportional to
the input RMS voltage, feeding this voltage into a squarer/divider circuit (1/V2 corrector) and
providing the resulting signal to the multiplier that generates the current reference for the
inner current control loop (see Figure 39).
Doc ID 16047 Rev 2
25/48
Application information
L6563H
Figure 39. Voltage feedforward: squarer-divider (1/V2) block diagram and transfer characteristic
5HFWLILHGPDLQV
FXUUHQW
UHIHUHQFH
9FV[
($RXWSXW
9 &203 9FV[
/+
08/7,3/,(5
9 &203 9
LGHDOGLRGH
9
$FWXDO
,GHDO
9
08/7
0$,16'523
'(7(&725
9))
& ))
5 ))
9)) 908/7
!-V
In this way a change of the line voltage causes an inversely proportional change of the half
sine amplitude at the output of the multiplier (if the line voltage doubles the amplitude of the
multiplier output is halved and vice versa) so that the current reference is adapted to the new
operating conditions with (ideally) no need for invoking the slow dynamics of the error
amplifier. Additionally, the loop gain is constant throughout the input voltage range, which
improves significantly dynamic behavior at low line and simplifies loop design.
Actually, deriving a voltage proportional to the RMS line voltage implies a form of integration,
which has its own time constant. If it is too small the voltage generated is affected by a
considerable amount of ripple at twice the mains frequency that causes distortion of the
current reference (resulting in high THD and poor PF); if it is too large there is a
considerable delay in setting the right amount of feedforward, resulting in excessive
overshoot and undershoot of the pre-regulator's output voltage in response to large line
voltage changes. Clearly a trade-off was required.
The L6563H realizes a NEW voltage feed forward that, with a technique that makes use of
just two external parts, strongly minimizes this time constant trade-off issue whichever
voltage change occurs on the mains, both surges and drops. A capacitor CFF and a resistor
RFF, both connected from the pin VFF (#5) to ground, complete an internal peak-holding
circuit that provides a DC voltage equal to the peak of the rectified sine wave applied on pin
MULT (#3). In this way, in case of sudden line voltage rise, CFF is rapidly charged through
the low impedance of the internal diode; in case of line voltage drop, an internal “mains
drop” detector enables a low impedance switch which suddenly discharges CFF avoiding
long settling time before reaching the new voltage level. Consequently, an acceptably low
steady-state ripple and low current distortion can be achieved without any considerable
undershoot or overshoot on the pre-regulator's output, like in systems with no feedforward
compensation.
The twice-mains-frequency (2•fL) ripple appearing across CFF is triangular with a peak-topeak amplitude that, with good approximation, is given by:
ΔVFF =
26/48
2 VMULTpk
1 + 4fLRFF CFF
Doc ID 16047 Rev 2
L6563H
Application information
where fL is the line frequency. The amount of 3rd harmonic distortion introduced by this
ripple, related to the amplitude of its 2•fL component, is:
D3 % =
100
2π fLRFF CFF
Figure 40 shows a diagram that helps choose the time constant RFF·CFF based on the
amount of maximum desired 3rd harmonic distortion. Always connect RFF and CFF to the
pin, the IC does not work properly if the pin is either left floating or connected directly to
ground.
Figure 40. RFF·CFF as a function of 3rd harmonic distortion introduced in the input
current
10
1
f L= 50 Hz
R FF · C FF [s]
0.1
f L= 60 Hz
0.01
0.1
1
10
D3 %
The dynamics of the voltage feedforward input, that is the output of the multiplier, is limited
downwards at 0.8 V (see Figure 39), so that cannot increase any more if the voltage on the
VFF pin is below 0.8 V. This helps to prevent excessive power flow when the line voltage is
lower than the minimum specified value.
6.4
THD optimizer circuit
The L6563H is provided with a special circuit that reduces the conduction dead-angle
occurring to the AC input current near the zero-crossings of the line voltage (crossover
distortion). In this way the THD (total harmonic distortion) of the current is considerably
reduced.
A major cause of this distortion is the inability of the system to transfer energy effectively
when the instantaneous line voltage is very low. This effect is magnified by the highfrequency filter capacitor placed after the bridge rectifier, which retains some residual
voltage that causes the diodes of the bridge rectifier to be reverse-biased and the input
current flow to temporarily stop.
To overcome this issue the device forces the PFC pre-regulator to process more energy
near the line voltage zero-crossings as compared to that commanded by the control loop.
This results in both minimizing the time interval where energy transfer is lacking and fully
discharging the high-frequency filter capacitor after the bridge.
Figure 41 shows the internal block diagram of the THD optimizer circuit.
Doc ID 16047 Rev 2
27/48
Application information
L6563H
Figure 41. THD optimizer circuit
W
W
9
W
&203
9))
08/7,3/,(5
08/7
W
WR3:0
FRPSDUDWRU
2))6(7
*(1(5$725
W
#9DF
#9DF!9DF
W
!-V
Figure 42. THD optimization: standard TM PFC controller (left side) and L6563H (right side)
Input current
Input current
Rectified mains voltage
Rectified mains voltage
Imains
Input
current
Imains
Input
current
Vdrain
MOSFET's drain
voltage
28/48
Doc ID 16047 Rev 2
Vdrain
MOSFET's drain
voltage
L6563H
Application information
Essentially, the circuit artificially increases the ON-time of the power switch with a positive
offset added to the output of the multiplier in the proximity of the line voltage zero-crossings.
This offset is reduced as the instantaneous line voltage increases, so that it becomes
negligible as the line voltage moves toward the top of the sinusoid. Furthermore the offset is
modulated by the voltage on the VFF pin (see “Voltage Feedforward” section) so as to have
little offset at low line, where energy transfer at zero crossings is typically quite good, and a
larger offset at high line where the energy transfer gets worse.
The effect of the circuit is shown in Figure 42, where the key waveforms of a standard TM
PFC controller are compared to those of this chip.
To take maximum benefit from the THD optimizer circuit, the high-frequency filter capacitor
after the bridge rectifier should be minimized, compatibly with EMI filtering needs. A large
capacitance, in fact, introduces a conduction dead-angle of the AC input current in itself even with an ideal energy transfer by the PFC pre-regulator - thus reducing the effectiveness
of the optimizer circuit.
6.5
Tracking boost function
In some applications it may be advantageous to regulate the output voltage of the PFC preregulator so that it tracks the RMS input voltage rather than at a fixed value like in
conventional boost pre-regulators. This is commonly referred to as “tracking boost” or
“follower boost” approach.
With the L6563H this can be realized by connecting a resistor (RT) between the TBO pin
and ground. The TBO pin presents a DC level equal to the peak of the MULT pin voltage and
is then representative of the mains RMS voltage. The resistor defines a current, equal to
V(TBO)/RT, that is internally 1:1 mirrored and sunk from pin INV (#1) input of the L6563H's
error amplifier. In this way, when the mains voltage increases the voltage at TBO pin
increases as well and so does the current flowing through the resistor connected between
TBO and GND. Then a larger current is sunk by INV pin and the output voltage of the PFC
pre-regulator is forced to get higher. Obviously, the output voltage moves in the opposite
direction if the input voltage decreases.
To avoid undesired output voltage rise should the mains voltage exceed the maximum
specified value, the voltage at the TBO pin is clamped at 3V. By properly selecting the
multiplier bias it is possible to set the maximum input voltage above which input-to-output
tracking ends and the output voltage becomes constant. If this function is not used, leave
the pin open: the device regulates a fixed output voltage.
Starting from the following data:
●
Vin1 = minimum specified input RMS voltage;
●
Vin2 = maximum specified input RMS voltage;
●
Vo1 = regulated output voltage @ Vin = Vin1;
●
Vo2 = regulated output voltage @ Vin = Vin2;
●
Vox = absolute maximum limit for the regulated output voltage;
to set the output voltage at the desired values use the following design procedure:
Doc ID 16047 Rev 2
29/48
Application information
1.
L6563H
Determine the input RMS voltage Vinclamp that produces Vo = Vox:
Vin clamp =
Vox − Vo1
Vox − Vo 2
⋅ Vin 2 −
⋅ Vin1
Vo 2 − Vo1
Vo 2 − Vo1
and choose a value Vinx such that Vin2 ≤ Vinx < Vinclamp. This results in a limitation of
the output voltage range below Vox (it is equal Vox if one chooses Vinx = Vinclamp)
2.
Determine the divider ratio of the MULT pin (#3) bias:
3
k=
3.
4.
2 ⋅ Vin x
and check that at minimum mains voltage Vin1 the peak voltage on pin 3 is greater than
0.65 V.
Determine R1, the upper resistor of the output divider, for instance 3 MΩ.
Calculate the lower resistor R2 of the output divider and the adjustment resistor RT:
Vin 2 − Vin1
⎧
⎪⎪R2 = 2.5 ⋅ R1⋅ (Vo − 2.5 ) ⋅ Vin − (Vo − 2.5 ) ⋅ Vin
1
2
2
1
⎨
Vin 2 − Vin1
⎪R T = 2 ⋅ k ⋅ R1⋅
⎪⎩
Vo 2 − Vo1
5.
Check that the maximum current sourced by the TBO pin (#6) does not exceed the
maximum specified (0.2 mA):
ITBO max =
3
≤ 0.2 ⋅ 10 − 3
RT
Figure 43 shows the internal block diagram of the tracking boost function.
Figure 43. Tracking boost block
42!#+).'
"//34
#522%.4
-)22/2
4"/
)4"/
#/-0
"5&&%2
FROM
6&&
6
24
).6
)4"/
TO-ULTIPLIER
6
%RROR!MPLIFIER
6/54
2
2
!-V
30/48
Doc ID 16047 Rev 2
L6563H
Application information
Figure 44. Tracking output voltage vs Input voltage characteristic with TBO
9R 9R [
9R 9LQ 9R 9LQ 9LQ
9LQ 9LQ [
!-V
6.6
Inductor saturation detection
Boost inductor's hard saturation may be a fatal event for a PFC pre-regulator: the current upslope becomes so large (50-100 times steeper, see Figure 45) that during the current sense
propagation delay the current may reach abnormally high values. The voltage drop caused
by this abnormal current on the sense resistor reduces the gate-to-source voltage, so that
the MOSFET may work in the active region and dissipate a huge amount of power, which
leads to a catastrophic failure after few switching cycles.
However, in some applications such as ac-dc adapters, where the PFC pre-regulator is
turned off at light load for energy saving reasons, even a well-designed boost inductor may
occasionally slightly saturate when the PFC stage is restarted because of a larger load
demand. This happens when the restart occurs at an unfavorable line voltage phase, i.e.
when the output voltage is significantly below the rectified peak voltage. As a result, in the
boost inductor the inrush current coming from the bridge rectifier adds up to the switched
current and, furthermore, there is little or no voltage available for demagnetization.
To cope with a saturated inductor, the L6563H is provided with a second comparator on the
current sense pin (CS, pin 4) that stops the IC if the voltage, normally limited within 1.1 V,
exceeds 1.7 V. After that, the IC attempts to restart by the internal starter circuitry; the
starter repetition time is twice the nominal value to guarantee lower stress for the inductor
and boost diode. Hence, the system safety is considerably increased.
Figure 45. Effect of boost inductor saturation on the MOSFET current and detection method
Doc ID 16047 Rev 2
31/48
Application information
6.7
L6563H
Power management/housekeeping functions
A special feature of this IC is that it facilitates the implementation of the “housekeeping”
circuitry needed to co-ordinate the operation of the PFC stage to that of the cascaded DCDC converter. The functions realized by the housekeeping circuitry ensure that transient
conditions like power-up or power down sequencing or failures of either power stage be
properly handled.
This device provides some pins to do that. One communication line between the IC and the
PWM controller of the cascaded dc-dc converter is the pin PWM_LATCH (Figure 47b),
which is normally open (high impedance) when the PFC works properly, and goes high if it
loses control of the output voltage (because of a feedback loop disconnection) with the aim
of latching off the PWM controller of the cascaded dc-dc converter as well (see “Feedback
failure protection” section for more details).
A second communication line can be established via the disable function included in the
PFC_OK pin (see “Feedback failure protection” section for more details). Typically this line is
used to allow the PWM controller of the cascaded dc-dc converter to drive in burst mode
operation the L6563H in case of light load and to minimize the no-load input consumption.
Interface circuits like those are shown in Figure 46.
Figure 46. Interface circuits that let dc-dc converter's controller IC drive L6563H in
burst mode
3)&B2.
/$
/+
3)&B6723
581
3)&B2.
/
/+
3)&B6723
581
!-V
The third communication line is the pin PWM_STOP (#11), which works in conjunction with
the pin RUN (#12). The purpose of the PWM_STOP pin is to inhibit the PWM activity of both
the PFC stage and the cascaded dc-dc converter. The pin is an open collector, normally
open, that goes low if the device is disabled by a voltage lower than 0.8 V on the RUN pin. It
is important to point out that this function works correctly in systems where the PFC stage is
the master and the cascaded dc-dc converter is the slave or, in other words, where the PFC
stage starts first, powers both controllers and enables/disables the operation of the dc-dc
stage. The pin RUN can be used to start and stop the main converter. In the simplest case,
to enable/disable the PWM controller the pin PWM_STOP can be connected to the output of
the error amplifier (Figure 47a).
32/48
Doc ID 16047 Rev 2
L6563H
Application information
Figure 47. Interface circuits that let the L6563H switch on or off a PWM controller
21
581
/+
3:0B6723
/+
3:0B/$7&+
2))
8&[;
8&[;
/$;
/;
/$;
RU
;
;
/$; /; /$; 3:05(6
FRQWUROOHU
DQRWODWFKHG
3:05(6
FRQWUROOHU
EODWFKHG
!-V
If the chip is provided with a soft-start pin, it is possible to delay the start-up of the dc-dc
stage with respect to that of the PFC stage, which is often desired, as described in
Figure 48. An underlying assumption in order for that to work properly is that the UVLO
thresholds of the PWM controller are certainly higher than those of the L6563H.
Figure 48. Interface circuits for power up sequencing when dc-dc has the SS
function
21
581
/+
3:0B6723
2))
/$; /; /$; ;
66
3:05(6
FRQWUROOHU
&66
!-V
If this is not the case or it is not possible to achieve a start-up delay long enough (because
this prevents the dc-dc stage from starting up correctly) or, simply, the PWM controller is
devoid of soft start, the arrangement of Figure 49 lets the dc-dc converter start-up when the
voltage generated by the PFC stage reaches a preset value. The technique relies on the
UVLO thresholds of the PWM controller.
Doc ID 16047 Rev 2
33/48
Application information
L6563H
Figure 49. Interface circuits for actual power-up sequencing (master PFC)
+9EXV
6XSSO\UDLO
%&
/$ ;
8&[;
8&[;
/ ;
/;
N7
9FF
21
581
2))
3:0B6723
%&&
9=
;
3:0
FRQWUROOHU
/+
3)&B2.
9FFB2II 9=9FFPD[
!-V
Another possible use of the RUN and PWM_STOP pins (again, in systems where the PFC
stage is the master) is the brownout protection, thanks to the hysteresis provided.
The brownout protection is basically a not-latched device shutdown function that is activated
when a condition of mains undervoltage is detected. This condition may cause overheating
of the primary power section due to an excess of RMS current. Brownout can also cause the
PFC pre-regulator to work open loop and this could be dangerous to the PFC stage itself
and the downstream converter, should the input voltage return abruptly to its rated value.
Another problem is the spurious restarts that may occur during converter power down and
that cause the output voltage of the converter not to decay to zero monotonically. For these
reasons it is usually preferable to shutdown the unit in case of brownout.
IC shutdown upon brownout can be easily realized as shown in Figure 50. The scheme on
the left is of general use, that one on the right can be used if the bias levels of the multiplier
and the RFF·CFF time constant are compatible with the specified brownout level and with the
specified holdup time respectively. In this latest case, an additional resistor voltage divider
and one capacitor are not needed.
In table 1 it is possible to find a summary of all of the above mentioned working conditions
that cause the device to stop operating.
Figure 50. Brownout protection (master PFC)
L6563H
12
RUN
RUN
12
L6563H
34/48
Doc ID 16047 Rev 2
L6563H
6.8
Application information
High-voltage start-up generator
Figure 51 shows the internal schematic of the high-voltage start-up generator (HV
generator). It is made up of a high-voltage N-channel FET, whose gate is biased by a 15 MΩ
resistor, with a temperature-compensated current generator connected to its source.
Figure 51. High-voltage start-up generator: internal schematic
+96
/+
9FFB2.
07
+9B(1
,+9
9FF
&21752/
,FKDUJH
*1'
!-V
The HV generator is physically located on a separate chip, made with BCD off-line
technology able to withstand 700 V, controlled by a low-voltage chip, where all of the control
functions reside.
With reference to the timing diagram of Figure 52, when power is first applied to the
converter the voltage on the bulk capacitor (Vin) builds up and, at about 80 V, the HV
generator is enabled to operate (HV_EN is pulled high) so that it draws about 1 mA. This
current, minus the device's consumption, charges the bypass capacitor connected from pin
Vcc (16) to ground and makes its voltage rise almost linearly.
Doc ID 16047 Rev 2
35/48
Application information
L6563H
Figure 52. Timing diagram: normal power-up and power-down sequences
9+9
5HFWLILHGLQSXWYROWDJH
,QSXWVRXUFHLVUHPRYHGKHUH
%XONFDSYROWDJH
9+9VWDUW
9FF
SLQ
'FGFORVHVUHJXODWLRQKHUH
W
9FF21
9FF2))
9FFUHVWDUW
W
*'
SLQ
+9FRQQHFWHGWREXONFDS
+9B(1
W
+9FRQQHFWHGWR
UHFWLILHGLQSXWYROWDJH
W
9FFB2.
,FKDUJH
W
P$
1RUPDO
RSHUDWLRQ
3RZHURQ
3RZHURII
W
!-V
As the Vcc voltage reaches the start-up threshold (12 V typ.) the low-voltage chip starts
operating and the HV generator is cut off by the Vcc_OK signal asserted high. The device is
powered by the energy stored in the Vcc capacitor until the self-supply circuit (we assume
that it is made with an auxiliary winding in the transformer of the cascaded dc-dc converter
and a steering diode) develops a voltage high enough to sustain the operation. The residual
consumption of this circuit is just the one on the 15 MΩ resistor (10 mW at 400 Vdc),
typically 50-70 times lower, under the same conditions, as compared to a standard start-up
circuit made with external dropping resistors.
At converter power-down the dc-dc converter loses regulation as soon as the input voltage
is so low that either peak current or maximum duty cycle limitation is tripped. Vcc then drops
and stops IC activity as it falls below the UVLO threshold (9.5 V typ.). The Vcc_OK signal is
de-asserted as the Vcc voltage goes below a threshold VCCrestart located at about 6 V.
The HV generator can now restart. However, if Vin < VHVstart, HV_EN is de-asserted too
and the HV generator is disabled. This prevents converter's restart attempts and ensures
monotonic output voltage decay at power-down in systems where brownout protection (see
the relevant section) is not used.
If the device detects a fault due to feedback failure the pin PWM_LATCH is asserted high
(see “Feedback failure protection” section for more details) and, in order to maintain alive
this signal to be provided to the DC-DC converter, the internal VCCrestart is brought up to
over the VccOff (Turn-off threshold). As a result, shown in Figure 53, the voltage at pin Vcc,
oscillates between its turn-on and turn-off thresholds until the HV bus is recycled and drops
below the start up threshold of the HV generator.
The High Voltage Start-up circuitry is capable to guarantee a safe behavior in case of short
circuit present on the dc-dc output when the Vcc of both controllers are generated by the
same auxiliary winding. The Figure 54 shows how the PFC manages the Vcc cycling and
the associated power transfer. At short circuit the auxiliary circuit is no longer able to sustain
the Vcc which start dropping; reaching its VccOFF threshold the IC stops switching, reduces
36/48
Doc ID 16047 Rev 2
L6563H
Application information
consumption and drops more until the Vccrestart threshold is tripped. Now, the high voltage
start-up generator restarts and when the Vcc crosses again its turn on threshold the IC
starts switching. In this manner the power is transferred from mains to PFC output only
during a short time for each Trep cycle.
Figure 53. High-voltage start-up behaviour during latch-off protection
9FF
SLQ
9FF21
)DXOWRFFXUVKHUH
9FF2))
9FFUHVWDUW
+9JHQHUDWRULVWXUQHGRQ
'LVDEOHODWFKLVUHVHWKHUH
*'
SLQ
+9JHQHUDWRUWXUQRQLVGLVDEOHGKHUH
W
,QSXWVRXUFHLVUHPRYHGKHUH
W
+9B(1
W
9LQ
9+9VWDUW
W
3:0B/$7&+
SLQ
W
!-V
Figure 54. High-voltage start-up managing the dc-dc output short-circuit
9FF
SLQ
6KRUWFLUFXLWRFFXUVKHUH
9FF21
9FF2))
9FFUHVWDUW
7UHS
*'
SLQ
9FFB2.
W
W
,FKDUJH
W
P$
W
!-V
Doc ID 16047 Rev 2
37/48
Application information
Table 5.
L6563H
Summary of L6563H idle states
Typical IC
PWM_LATCH PWM_STOP
Condition
Caused or revealed
bey
IC
behavior
Restart
condition
consumption
Status
Status
UVLO
Vcc < VccOff
Disabled
Vcc > VccOn
90 µA
Off
High
Feedback
disconnected
PFC_OK > VPFC_OK_S
AND
INV < PFC_OK - 40mV
Latched
Vcc < Vccrestart
then
Vcc > VccOn
180 µA
High
High
Standby
PFC_OK < VPFC_OK_D
PFC_OK >
VPFC_OK_E
1.5 mA
Off
High
AC brownout
RUN < VDIS
RUN > VEN
1.5 mA
Off
Low
OVP
PFC_OK > VPFC_OK_S
PFC_OK <
VPFC_OK_R
2.2 mA
Off
High
Low
consumption
COMP < 2.4V
Burst
mode
COMP > 2.4V
2.2 mA
Off
High
Saturated
boost
inductor
Vcs > VCS_th
Doubled
Tstart
Auto restart
2.2 mA
Off
High
38/48
Stop
switching
Doc ID 16047 Rev 2
&
1
9DF
5
0
5
0
5
0
&
X)
Doc ID 16047 Rev 2
5
.
5
.
5
0
&
1
&
1
&
S
&
1
5
.
&
1
58 1
=& '
*1'
+96
1&
3:06723
3:0/$7&+
3)& 2.
7%2
9))
&6
08/7
*'
9&&
5
.
/+
&203
,1 9
8
5
.
&
1
/
+) < 57
'
*%8-
a
a
)
)8 6($
B
&
1
-
0.'6 5
.
&
1
&
X)9
-3
&
1 9
5
.
5
.
5
.
&
1
5
5
5
5
9&&
*1'
3:0B6723
3:0B/$7&+
212))
5
5
5
0
+6
+($76,1 .
4
67)101
5
5
5
.
'
677+/
5
17& 56
-
&21
5
5
'
//
'
1
'
%=;&
5
5
/
65: 34;;;9
:,5 (-80 3(5 ,1 68/$7('
&
X) 9
5
0
5
0
5
0
5
.
5
0
5
0
-
0.'6 7
L6563H
Application examples and ideas
Application examples and ideas
Figure 55. Demonstration board EVL6563H-100W, wide-range mains: electrical
schematic
!-V
39/48
Application examples and ideas
L6563H
Figure 56. L6563H 100 W TM PFC evaluation
board: compliance to EN61000-3-2
standard
Me as ur e d v alue
Figure 57. L6563H 100 W TM PFC evaluation
board: compliance to JEITA-MITI
standard
EN61 000 -3- 2 clas s -D lim it s
Measured value
JEITA-MITI Class-D limits
10
Harmonic Current [A]
Harmonic Current [A]
1
0 .1
0.01
0.001
1
0.1
0.01
0.001
0.0001
0 .0 001
1
3
5
7
9 11 13 1 5 17 19 2 1 2 3 25 2 7 2 9 31 3 3 3 5 37 3 9
1
3
5
7
9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39
Harmonic Order [n]
Harmonic Order [n]
Vin = 230 Vac - 50 Hz, Pout = 100 W
Vin = 100 Vac - 50 Hz, Pout = 100 W
THD = 7.58%, PF = 0.979
THD = 2.5%, PF = 0.997
Figure 58. L6563H 100 W TM PFC evaluation
board: input current waveform
@230-50 Hz - 100 W load
Figure 59. L6563H 100W TM PFC evaluation
board: input current waveform
@100 V-50 Hz - 100 W load
40/48
Doc ID 16047 Rev 2
9DF
&
X)
5
.
5
.
5
0
5
.
5
5
&
1
&
1<
5
10
5
0
5
0
&
1;
&
1<
&
1
&
1
&
1
5
.
5
.
5
.
5
10
4
10
+96
5
.
&
5
5
3:0/ $7&+
1&
3:06723
7% 2
3)&2 .
581
9))
*'
=&'
&6
*1'
9&&
8
/ +
5
.
a
08/7
'
*%8-
&203
,19
5
10
'
%=9%
10
&
&
3)
/
$ &
1;
B
5
.
&
19
5
.
5
.
5
0
&
X ) 9
&
1
&
1
&
1
&
1
5
.
&
1
5
5
'
// &
1)
'
// &
1
5
5
&
3)
5
0
5
.
5
5
',6
/,1(
,6(1
67%<
5)0,1
&)
'(/$<
.
5
&
X ) 9
*1'
/9*
9&&
1&
287
+9*
9%22 7
-3
5
5
5
.
3)&6723
5
10
'
%=9%
8
/ $
&66
5
5
'
1
'
// 4
%&&
'
// &
1
'
10
/
65: 34 ;;;9
)
)86(7 $
X) 9
5
5
'
// '
677+/
&
&
1 X ) 9
+6
+($76,1 .
4
67)10 1
&
1
-
0.'6 5
17& 5 6
5
0
5
0
5
0
-3
5
.
5
.
5
0
5
0
5
0
-3;
5
5
'
// &
1
5
5
5
.
+6
'
// 5
5
5
.
'
// 5
.
X 9
&
4
67310)3
&
X) 9
'
6736/$
'
// &
3)
5
5
5
5
4
67310)3
&
1<
&
1<
&
1
+6
+($76,1 .
8
6)+ $
-3
7
$ $
8
7/ $,=
5
.
5
.
&
10
5
.
5
.
'
// 5
5
'
// '
// 5
5
5
.
5
.
&
1
4
6731) /
5
.
4
6731) /
'
// 5
.
&
X)9
5
5
&
X) 9< ;)
5
.
5
.
5
.
5
.
&
10
5
10
-3;
'96
'96
(1
6*1'
&
1)
5
5
&
X) 9< ;)
*'
3*1'
*'
9&&
8
65.
5
10
&
X) 9< ;)
/
X
'
1
&
5
.
5
.
%=9&
-
&
1)
4
%&&
&
X ) 9
5
5
4
%&&
5
.
0.'6 5
.
a
Doc ID 16047 Rev 2
L6563H
Application examples and ideas
Figure 60. Application board 90W-19V adapter with L6563H, L6599A, SRK2000
!-V
41/48
&
X)
5
.
5
.
9DF
5
0
5
.
5
5
&
1
5
10
5
0
5
0
&
1
&
1
&
1
&
1;
5
.
5
.
581
3:06723
9))
7%2
5
10
5
.
&
+96
3:0/$7&+
4
10
1&
3)&2.
5
5
=&'
*1'
08/7
&6
*'
9&&
8
/+
5
.
&
1;
&203
,19
5
.
/
$
5
10
'
%=9%
10
&
&
3)
&
1<
&
1<
B
5
.
5
.
5
0
&
X)9
a
5
.
&
1
&
1
&
1
&
1
5
.
&
1
5
5
'
//
&
1)
'
//
19
&
&
1
5
5
&
3)
5
0
5
.
5
5
'(/$<
',6
/,1(
,6(1
67%<
5)0,1
&)
'
1
.
5
&
X)9
'
//
*1'
/9*
9&&
1&
287
+9*
9%227
-3
5
5
5
.
3)&6723
5
10
'
%=9%
8
/$
&66
5
5
4
%&&
'
//
&
1
'
10
/
X)9
5
5
'
//
'
677+/
&
&
1 X)9
+6
+($76,1.
4
67)101
&
1
'
*%8-
5
17&56
5
0
5
0
5
0
-3
5
.
5
.
5
0
5
0
5
0
-3;
5
5
'
//
&
1
5
5
5
.
+6
'
//
5
5
5
.
'
//
5
.
&
X)9
9(5,&$5(6(5,(0$5&
$
67310 )3
&
X)9
'
6736/$
'
//
5
5
5
5
4
67310)3
4
&
3)
)
)86(7$
-
0.'6
&
1
7
7%$
9(5,),&$5(3,12876(&21'$5,
2
&
1<
&
1<
8
6)+$
-3
8
7/$,=
&
1
5
.
&
10
5
.
5
.
26&21
5
.
&
X)9
5
5
'
%$6
5
.
5
.
5
.
5
.
5
.
'
%$6
5
5
5
.
&
10
5
10
'
%$6
4
67.1//+
5
.
4
67.1//+
9287
5
.
5
.
%=9%
'
1
&
-
4
%&&
5
.
'
%$6
5
5
&
1
-3;
'96
'96
(1
6*1'
&
1
&
X)
5
5
'$8*+7(5%2$5'
*'
3*1'
*'
9&&
8
65.
9287
4
%&&
5
.
0.'6
$''('&5(029('&5
5
.
5
10
&
X)9<;)
/
X
&
&
&
X)96$X)96$ X)96$
-;
PP GHJ3,1 675,3
&
X)96$
-;$
3&%+2/(675,3
a
Doc ID 16047 Rev 2
42/48
Application examples and ideas
L6563H
Figure 61. Application board 130 W-12 V adapter with L6563H, L6599A, SRK2000
!-V
1
.
&
1
&
5
5
0
5
0
5
0
9DF
&21,1
-
3: 0B6723
5
0
5
0
5
0
5
.
5
5
&
X)
&
X)
5
.
&
1
5
0
5
.
3)
&
9&&
&
Q);9 DF
17& 5 6
5
.
*& 386
9
7 $ 9
)
4
5 %& &
.
/
.
5
5
0
&
3:0 /$7& +
5(6
/
5
.
&
5
.
5
.
Q)9
&
&
9&&
a
a
'
';% '
';% 5
5
5
0
X)9
&
1
Q);9 DF
3: 0B6723
-3
10
+96
1&
3:0 6723
58 1
=&'
*1'
*'
9&&
/6
8
Q);9 DF
3)& 2.
7% 2
9))
&6
08/7
&203
,19
.
5
5
0
&0 P+ $
a
a
-
&21
212))
3:0B/ $7&+
3:0B6723
*1'
9&&
-3
10
4
%& &
5
.
&
3)
+6
+($7 6,1.
5
.
&
3)
&
Q)9
&
Q)9
/
"" X+$
/
72 52,'( X +
5
.
'
// 5;
5
5
.
'
// '
6736/ $
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5 :
'
// '
// '
// &
X) 9
'
6736&'
'
1 &
&
9
5
5 :
5
5 :
5
5
4
67) 101
X)9
X)9
5
.
&
+6
+($7 6,1.
5
5 :
5
5 :
5
5
4
67) 101
4
67) 101
-
9GF
9GF
1&
571
571
5
5 :
9RXW
X)9
X)9
&
Doc ID 16047 Rev 2
L6563H
Application examples and ideas
Figure 62. Demonstration board EVL6563H-650W wide-range mains: electrical schematics
!-V
43/48
Package mechanical data
8
L6563H
Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK is an ST trademark.
Table 6.
SO16 mechanical data
mm
Dim.
Min.
Typ.
A
1.75
A1
0.1
A2
1.25
b
0.31
0.51
c
0.17
0.25
D
9.8
9.9
10
E
5.8
6
6.2
E1
3.8
3.9
4
e
0.25
1.27
h
0.25
0.5
L
0.4
1.27
k
0
8
ccc
44/48
Max.
0.1
Doc ID 16047 Rev 2
L6563H
Package mechanical data
Figure 63. SO16 mechanical data
Doc ID 16047 Rev 2
45/48
Ordering codes
9
L6563H
Ordering codes
Table 7.
Ordering information
Order codes
Package
L6563H
Packing
Tube
SO16
L6563HTR
46/48
Tape and reel
Doc ID 16047 Rev 2
L6563H
10
Revision history
Revision history
Table 8.
Document revision history
Date
Revision
Changes
22-Jul-2009
1
Initial release.
01-Feb-2010
2
Updated Table 4 on page 11
Doc ID 16047 Rev 2
47/48
L6563H
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2010 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
48/48
Doc ID 16047 Rev 2