Series/Type: E375 The following products presented in this data sheet are being withdrawn. Ordering Code B69812N1847E375 Substitute Product Date of Withdrawal 06.07.2007 Deadline Last Orders 31.01.2008 Last Shipments 30.04.2008 For further information please contact your nearest EPCOS sales office, which will also support you in selecting a suitable substitute. The addresses of our worldwide sales network are presented at www.epcos.com/sales. Microwave Ceramics and Modules 2-Pole Filter for PCN RX Filter B69812N1847E375 Data Sheet Features z SMD filter consisting of coupled resonators with stepped impedances z (NdBa)TiO3 (εr = 88 / TCf =0±10 ppm/K) with a coating of copper (10µm) and tin (>5µm) z Excellent reflow solderability, no migration effect due to copper/tin metallization Index Page 2 z Component drawing z Recommended footprint Page 3 z Characteristics z Maximum ratings z Typical passband characteristic Page 4 z Processing information z Soldering requirements z Delivery mode ISSUE DATE 09.03.04 ISSUE B PUBLISHER SAW MWC PD PAGE 1/4 Microwave Ceramics and Modules 2-Pole Filter for PCN RX Filter B69812N1847E375 Data Sheet Component drawing View from below onto the solder terminals and view from beside Recommended footprint ISSUE DATE 09.03.04 ISSUE B PUBLISHER SAW MWC PD PAGE 2/4 Microwave Ceramics and Modules 2-Pole Filter for PCN RX Filter B69812N1847E375 Data Sheet Characteristics min. typ. max. 1842.5 - MHz 1.1 1.5 dB Passband αIL B 75 Amplitude ripple (peak - peak) ∆α 0.3 0.5 SWR 1.5 2.0 Impedance Z 50 Power P Center frequency fc - Insertion loss Standing wave ratio Attenuation α at DC to 1500 MHz at 1500 to 1705 MHz at 1705 to 1785 MHz at 1980 to 3500 MHz MHz dB Ω 1.0 32 15 2.5 10 W 35 17 3 15 dB dB dB dB Maximum ratings IEC climatic category (IEC 68-1) - 40/+ 90/56 Operating temperature Top - 20 / + 80 °C Typical passband characteristic 1.4 1.5 1.6 1.7 1.8 1.9 2 2.1 2.2 0 attenuation [dB] -10 -20 DB[S11] DB[S21] -30 -40 -50 -60 frequency [GHz] ISSUE DATE 09.03.04 ISSUE B PUBLISHER SAW MWC PD PAGE 3/4 Microwave Ceramics and Modules 2-Pole Filter for PCN RX Filter B69812N1847E375 Data Sheet Processing information z Wettability acc. to IEC 68-2-58: ≥ 75% (after aging) Soldering Requirements Profile for eutectic SnPb solder paste Profile for leadfree solder paste Soldering type reflow Maximum soldering temperature 235 (max. 2 sec.) (measuring point on top surface of the component) 225 (max. 10 sec.) reflow 260 (max. 2 sec.) °C 250 (max. 10 sec.) °C Recommended soldering conditions (infrared): within 10 sec. Temp. [°C] within 10 sec. Temp. [°C] 245°C±5°C 215°C±10°C 20-40 sec. 30 sec. Time [sec.] 2.5 °C/s 40-80 sec. 2-3 min. Time [sec.] > - 5 °C/s Delivery mode z Blister tape acc. to IEC 286-3, PS, grey z Pieces/tape: 3000 Reel: diameter - 330 mm Profile B-B: Profile A-A: A B B A direction of unreeling EPCOS AG 2001. All Rights Reserved. Reproduction, publication and dissemination of this data sheet, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. The information contained in this data sheet describes the type of component and shall not be considered as guaranteed characteristics. Purchase orders are subject to the General Conditions for the Supply of Products and Services of the Electrical and Electronics Industry recommended by the ZVEI (German Electrical and Electronic Manufacturers' Association), unless otherwise agreed. ISSUE DATE 09.03.04 ISSUE B PUBLISHER SAW MWC PD PAGE 4/4