EPCOS B69812N2457D101

Microwave Ceramics and Modules
2 – Pole Filter for W - LAN
Filter
B69812N2457D101
Datas Sheet
Features
• Low Profile (maximum height 1.4 mm)
• SMD filter consisting of coupled resonators with stepped impedances
• Low losses
• High attenuations at GSM (900, 1800) and UMTS bands
• High attenuation at 2 times center frequency
• (NdBa)TiO3 (εr = 88 / TCf =0±10 ppm/K) with a coating of copper (10µm) and tin (>5µm)
• Excellent reflow solderability, no migration effect due to copper/tin metallization
Index
Page 2
• Component drawing, Marking
• Recommended footprint
Page 3
• Characteristics
• Maximum ratings
• Typical passband characteristic
Page 4
• Processing information
• Soldering requirements
• Delivery mode
ISSUE DATE
31.10.03
ISSUE
B
PUBLISHER
SAW MWC PD
PAGE
1/4
Microwave Ceramics and Modules
2 – Pole Filter for W - LAN
Filter
B69812N2457D101
Datas Sheet
Component drawing, Marking
Recommended footprint
I/O
G
G
ISSUE DATE
Solder Pads:
I/O Pads must be
connected to lines with
50 Ω impedance.
In the application a
termination of 50 Ω
must be realized.
I/O
Ground, covered with
solder resist, connected
to lower ground plane
by vias with maximum
diameter of 0.3mm and
max. distance of 1mm
G
31.10.03
ISSUE
B
PUBLISHER
SAW MWC PD
PAGE
2/4
Microwave Ceramics and Modules
2 – Pole Filter for W - LAN
Filter
B69812N2457D101
Datas Sheet
Characteristics
min.
Center frequency
Insertion loss
fc αIL
B 100
Passband (2400- 2500)
max.
2.450
1.4
1.8
GHz
dB
MHz
∆α
SWR
Z
α
Amplitude ripple (peak - peak)
Standing wave ratio
Impedance
Attenuation
at DC to 827 MHz
at 880 to 960 MHz
at 1500 to 1910 MHz
at 1930 to 1990 MHz
at 1990 to 2100 MHz
at 2100 to 2170 MHz
at 3200 to 3500 MHz
at 4000 to 4600 MHz
at 4800 to 5000 MHz
at 5600 to 5789 MHz
at 6400 to 6615 MHz
Maximum ratings
IEC climatic category (IEC 68-1)
typ.
0.4
1.5
50
0.8
2.0
dB
Ω
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
60
55
47
49
34
27
30
30
30
20
10
56
48
45
48
30
23
28
27
25
15
5
- 40 /+ 90/56
Operating temperature
Top - 40 / + 85
°C
Typical passband characteristics
0
-5
-10
attenuation [dB]
-15
-20
S21 [dB]
S11 [dB]
-25
-30
-35
-40
-45
-50
2,1
2,15
2,2
2,25
2,3
2,35
2,4
2,45
2,5
2,55
2,6
frequency [GHz]
ISSUE DATE
31.10.03
ISSUE
B
PUBLISHER
SAW MWC PD
PAGE
3/4
Microwave Ceramics and Modules
2 – Pole Filter for W - LAN
Filter
B69812N2457D101
Datas Sheet
Processing information
z Wettability acc.to IEC 68-2-58: ≥ 75% (after aging)
Soldering Requirements
Profile for eutectic
SnPb solder paste
Profile for leadfree
solder paste
Soldering type
reflow
Maximum soldering temperature
235 (max. 2 sec.)
(measuring point on top surface of the component) 225 (max. 10 sec.)
reflow
260 (max. 2 sec.) °C
250 (max. 10 sec.) °C
Recommended soldering conditions (infrared):
within 10 sec.
Temp. [°C]
within 10 sec.
Temp. [°C]
245°C±5°C
215°C±10°C
20-40 sec.
30 sec.
Time [sec.]
2.5 °C/s
40-80 sec.
2-3 min.
Time [sec.]
> - 5 °C/s
Delivery mode
• Blister tape acc. to IEC 286-3, grey
• Pieces/tape: 4000
 EPCOS AG 2001. All Rights Reserved. Reproduction, publication and dissemination of this data sheet, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
The information contained in this data sheet describes the type of component and shall not be considered as guaranteed characteristics.
Purchase orders are subject to the General Conditions for the Supply of Products and Services of the Electrical and Electronics Industry
recommended by the ZVEI (German Electrical and Electronic Manufacturers' Association), unless otherwise agreed.
ISSUE DATE
31.10.03
ISSUE
B
PUBLISHER
SAW MWC PD
PAGE
4/4