FUJITSU SEMICONDUCTOR DATA SHEET DS04-29122-1E Spread Spectrum Clock Generator MB88162 ■ DESCRIPTION MB88162 is a clock generator for EMI (Electro Magnetic Interference) reduction. The peak of unnecessary radiation noise (EMI) can be attenuated by making the oscillation frequency slightly modulate periodically with the internal modulator. ■ FEATURES • • • • • • • • • • • • Input frequency : 12 MHz to 28 MHz (Multiplied by 1), 20 MHz to 42 MHz (Multiplied by 4) Multiplication rate : 1, 4 Output frequency : 12 MHz to 28 MHz (Multiplied by 1), 80 MHz to 168 MHz (Multiplied by 4) Modulation rate : no modulation, ± 0.5%, ± 1.0%, ± 2.0%, − 1.0%, − 2.0%, − 4.0% (The terminal can be selected.) Equipped with oscillation circuit : Range of oscillation 12 MHz to 42 MHz Built-in oscillation stabilization capacitance : 4 pF (Typ) Modulation clock output Duty : 40% to 60% Modulation clock Cycle-Cycle Jitter : Less than 100 ps Low power consumption by CMOS process : 7.0 mA (24 MHz : no load, Typ-sample, Typ-condition) Power supply voltage : 2.7 V to 3.6 V (Multiplied by 1), 3.0 V to 3.6 V (Multiplied by 4) Operating temperature : − 40 °C to + 85 °C Package : BCC 18-pin ■ PACKAGE 18-pin plastic BCC (LCC-18P-M05) MB88162 ■ PIN ASSIGNMENT NC NC NC NC (TOP VIEW) S0 15 14 13 12 11 10 OE VSS 16 9 XOUT SPRD 17 8 XIN 2 3 4 5 NC NC 1 7 NC S1 18 NC OUT MB88162 6 VDD MLTP ■ PIN DESCRIPTION 2 Pin no. Pin name I/O Description 1 S1 I 2 NC ⎯ Non-connection pin (do not connect anything) 3 NC ⎯ Non-connection pin (do not connect anything) 4 NC ⎯ Non-connection pin (do not connect anything) 5 NC ⎯ Non-connection pin (do not connect anything) 6 MLTP I 7 VDD ⎯ 8 XIN I Resonator connection pin/clock input pin 9 XOUT O Resonator connection pin 10 OE I Clock output enable pin (with pull-up resistance) 11 NC ⎯ Non-connection pin (do not connect anything) 12 NC ⎯ Non-connection pin (do not connect anything) 13 NC ⎯ Non-connection pin (do not connect anything) 14 NC ⎯ Non-connection pin (do not connect anything) 15 S0 I 16 VSS ⎯ 17 SPRD I Modulation type setting pin (with pull-up resistance) 18 OUT O Modulation clock output pin (OE= “L” Hi-Z output) Modulation rate setting pin (with pull-up resistance) Multiplication rate setting pin (with pull-down resistance) Power supply voltage pin Modulation rate setting pin (with pull-up resistance) GND pin MB88162 ■ I/O CIRCUIT TYPE Pin Circuit type 22 kΩ OE signal OE 800 kΩ Remarks • With pull-up resistor The value of pull-up resistor is switched by the input level of OE signal. 800 kΩ at OE= “L” (Typ) 22 kΩ at OE= “H” (Typ) • CMOS hysteresis input Note : At OE=“L” 22kΩ Pull Up cut 50 kΩ OE signal S0, S1, SPRD • With pull-up resistor 50 kΩ (Typ) • CMOS hysteresis input • Pull-up resistor is disconnected at OE= “L”, and internal signal is fixed to “L”. Note : At OE=“L” Pull Up cut • With pull-down resistor 50 kΩ (Typ) • CMOS hysteresis input • Pull-down resistor is disconnected at OE= “L”, and internal signal is fixed to “L”. MLTP OE signal 50 kΩ Note : At OE=“L” Pull Down cut OE signal • CMOS output • IOL = 8.0 mA • Hi-Z output at OE = “L” OUT Note : At OE=“L” Hi-Z output (Continued) 3 MB88162 (Continued) Pin Circuit type • Oscillation circuit • Built-in feedback resistance : 500 kΩ (Typ) • Built-in oscillation stabilization capacitance : 4 pF (Typ) XIN 4 pF XIN, XOUT XOUT 500 kΩ 4 pF 4 Remarks MB88162 ■ HANDLING DEVICES Preventing Latch-up A latch-up can occur if, on this device, (a) a voltage higher than power supply voltage or a voltage lower than GND is applied to an input or output pin or (b) a voltage higher than the rating is applied between power supply and GND. The latch-up, if it occurs, significantly increases the power supply current and may cause thermal destruction of an element. When you use this device, be very careful not to exceed the maximum rating. Handling unused pins Do not leave an unused input pin open, since it may cause a malfunction. Handle by, using a pull-up or pull-down resistor. Power supply pins Please design connecting the power supply pin of this device by as low impedance as possible from the current supply source. We recommend connecting electrolytic capacitor (about 10 µF) and the ceramic capacitor (about 0.01 µF) in parallel between power supply and GND near the device, as a bypass capacitor. Oscillation circuit Noise near the XIN pin and XOUT pin may cause the device to malfunction. Design printed circuit boards so that electric wiring of XIN pin or XOUT pin and the resonator do not intersect other wiring. Design the printed circuit board that surrounds the XIN pin and XOUT pin with ground. 5 MB88162 ■ BLOCK DIAGRAM VDD OE Output enable Power Down Multiplication rate setting MLTP Hi-Z control Modulation type setting SPRD PLL block Modulation rate setting Modulation clock output S0 Modulation rate setting S1 XOUT OUT Reference clock 4 pF Power Down XIN Rf = 500 kΩ 4 pF VSS 1 − M Phase compare Reference clock 1 − N Charge pump V/I conversion IDAC Modulation clock output Loop filter 1 − L ICO Modulation logic MB88162 PLL block A glitchless IDAC (current output D/A converter) provides precise modulation, thereby dramatically reducing EMI. 6 Modulation rate setting S0, S1 MB88162 ■ PIN SETTING After the pin setting is changed, the stabilization wait time of the modulation clock is required. The stabilization wait time of the modulation clock takes the maximum value of Lock-Up time in “• AC Characteristics” in ■ ELECTRICAL CHARACTERISTICS. Each setting pin contains the pull-up resistor or pull-down resistor. Therefore, these pins is set to default state for input opened. MLTP multiplication setting MLTP Multiplication rate Input Frequency Output Frequency Remarks L Multiplied by 1 12 MHz to 28 MHz 12 MHz to 28 MHz Default H Multiplied by 4 20 MHz to 42 MHz 80 MHz to 168 MHz ⎯ Note : Set MLTP pin to “L” for input opened because MLTP pin has the pull-down resistor. OE clock output enable OE Status Remarks L Modulation clock output (OUT pin) Hi-Z/Power down status ⎯ H Operation status Default Note : When OE pin is set to “L”, all oscillation circuits/PLL stop and enter power down mode, low-power consumption mode. Modulation clock output (OUT pin) becomes Hi-Z state during the power down. Set OE pin to “H” for input opened because OE pin has the pull-up resistor. SPRD modulation type setting SPRD Modulation type Remarks L Center spread ⎯ H Down spread Default Note : Set SPRD pin to “H” for input opened because SPRD pin has the pull-up resistor. S0/S1 modulation rate setting S1 S0 L Modulation rate Remarks At down spread At center spread L No modulation No modulation ⎯ L H − 1.0% ± 0.5% ⎯ H L − 2.0% ± 1.0% ⎯ H H − 4.0% ± 2.0% Default Note : Set S1 and S0 pins to “H” for input opened because the pins have the pull-up resistor. 7 MB88162 • Center spread Spectrum is spread (modulated) by centering on the non-spread frequency. Modulation width 2.0% Radiation level −1.0% +1.0% Frequency Non-spread frequency Example of center spread modulation rate ± 1.0% • Down spread Spectrum is spread (modulated) below the non-spread frequency. Radiation level Modulation width 2.0% −2.0% Frequency Non-spread frequency Example of down spread modulation rate − 2.0% 8 MB88162 ■ ABSOLUTE MAXIMUM RATINGS Parameter Rating Symbol Unit Min Max VDD − 0.5 + 4.0 V Input voltage* VI VSS − 0.5 VDD + 0.5 V Output voltage* VO VSS − 0.5 VDD + 0.5 V Storage temperature TST − 55 + 125 °C Operation junction temperature TJ − 40 + 125 °C Output current IO − 14 + 14 mA Overshoot VIOVER ⎯ VDD + 1.0 (tOVER ≤ 50 ns) V Undershoot VIUNDER VSS−1.0 (tUNDER ≤ 50 ns) ⎯ V Power supply voltage* * : The parameter is based on VSS = 0.0 V. WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings. Overshoot/Undershoot tUNDER ≤ 50 ns VIOVER ≤ VDD + 1.0 V VDD Input pin VSS tOVER ≤ 50 ns VIUNDER ≤ VSS − 1.0 V 9 MB88162 ■ RECOMMENDED OPERATING CONDITIONS (VSS = 0.0 V) Parameter Symbol Pin Power supply voltage VDD VDD “H” level input voltage VIH “L” level input voltage VIL XIN, MLTP, OE, SPRD, S1, S0 Input clock duty cycle tDCI Operating temperature Ta Conditions Value Unit Min Typ Max At MLTP = “L” 2.7 3.3 3.6 At MLTP = “H” 3.0 3.3 3.6 ⎯ VDD × 0.80 ⎯ VDD + 0.3 V ⎯ VSS ⎯ VDD × 0.20 V XIN Input frequency 12 MHz to 42 MHz 40 50 60 % ⎯ ⎯ − 40 ⎯ + 85 °C V WARNING: The recommended operating conditions are required in order to ensure the normal operation of the semiconductor device. All of the device’s electrical characteristics are warranted when the device is operated within these ranges. Always use semiconductor devices within their recommended operating condition ranges. Operation outside these ranges may adversely affect reliability and could result in device failure. No warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet. Users considering application outside the listed conditions are advised to contact their FUJITSU representatives beforehand. Input clock duty cycle (tDCI = tb/ta) ta tb VDD × 0.8V VDD × 0.5V XIN VDD × 0.2V 10 MB88162 ■ ELECTRICAL CHARACTERISTICS • DC Characteristics (Ta = − 40 °C to + 85 °C, VDD = 2.7 V to 3.6 V, VSS = 0.0 V) Parameter Symbol Pin Conditions Power supply current ICC VDD Power down current IPD VDD VOH OUT Output voltage VOL Output impedance Load capacitance Built-in oscillation stabilization capacitance Input pull-up resistance Input pull-down resistance ZOC CL OUT OUT Value Unit Min Typ Max 24 MHz output no load capacitance ⎯ 7.0 11.0 mA At power down (At OE=”L”) ⎯ 5 20 µA “H” level output, IOH= − 8 mA 0.8 × VDD ⎯ VDD V “L” level output, IOL = 8 mA VSS ⎯ 0.2 × VDD V MLTP = L, 12 MHz to 28 MHz output, VDD = 2.7 V to 3.6 V ⎯ 30 ⎯ Ω MLTP = H, 80 MHz to 168 MHz output, VDD = 3.0 V to 3.6 V ⎯ 20 ⎯ Ω MLTP = L, 12 MHz to 28 MHz output, VDD = 2.7 V to 3.6 V ⎯ ⎯ 15 pF MLTP = H, 80 MHz to 168 MHz output, VDD = 3.0 V to 3.6 V ⎯ ⎯ 15 pF COSC XIN, XOUT ⎯ ⎯ 4 ⎯ pF RPUOEH OE VIH = 0.8 × VDD 10 25 100 kΩ RPUOEL OE VIL = 0.0 V 500 800 1200 kΩ RPU SPRD, S1, S0 VIL = 0.0 V 25 50 200 kΩ RPD MLTP VIH = VDD 25 50 200 kΩ Note : When OE pin is set to “L”, the pull-up resistor connected to SPRD pin, S1 pin, and S0 pin and the pull-down resistor connected to MLTP pin are disconnected, and internal signal is fixed to “L”. See “■ I/O CIRCUIT TYPE” for details. 11 MB88162 • AC Characteristics Parameter Input frequency Crystal oscillation frequency Output frequency (Ta = − 40 °C to + 85 °C, VDD = 2.7 V to 3.6 V, VSS = 0.0 V) Symbol fin fx fOUT Pin XIN XIN, XOUT OUT Conditions Value Min Typ Max MLTP= “L”, VDD = 2.7 V to 3.6 V, Crystal oscillation input 12 ⎯ 28 MLTP= “H”, VDD = 3.0 V to 3.6 V, Crystal oscillation input 20 ⎯ 42 Fundamental oscillation, MLTP= “L”, VDD = 2.7 V to 3.6 V 12 ⎯ 28 Fundamental oscillation, MLTP= “H”, VDD = 3.0 V to 3.6 V 20 ⎯ 42 MLTP= “L”, VDD = 2.7 V to 3.6 V 12 ⎯ 28 MLTP= “H”, VDD = 3.0 V to 3.6 V 80 ⎯ 168 Unit MHz MHz MHz Output clock rise time tr OUT 0.2 × VDD to 0.8 × VDD Load capacitance 15 pF 0.4 ⎯ 4.0 ns Output clock fall time tf OUT 0.2 × VDD to 0.8 × VDD Load capacitance 15 pF 0.4 ⎯ 4.0 ns tDCC OUT 0.5 × VDD 40 ⎯ 60 % Input frequency at 24MHz, MLTP = “L” ⎯ 32.0 ⎯ Input frequency at 24MHz, MLTP = “H” ⎯ 21.3 ⎯ Output clock duty cycle Modulation frequency fMOD OUT kHz Lock-Up time tLK OUT ⎯ ⎯ 4 10 ms Cycle-Cycle jitter tJC OUT Ta= + 25°C, VDD=3.3V, No load capacitance, Standard deviation σ ⎯ ⎯ 100 ps Output enable “L” width tOELW OE ⎯ 1 ⎯ ⎯ µs Power supply rise time tVDR VDD MLTP= L, 0.0 V to 2.7 V 100 ⎯ ⎯ MLTP= H, 0.0 V to 3.0 V 100 ⎯ ⎯ Output Hi-Z start time after power down entry tPEZ OUT Rise time or fall time of “OE” at 5 ns ⎯ ⎯ 10 ns Output Hi-Z release time after power down exit tPIZ OUT Rise time or fall time of “OE” at 5 ns 0 ⎯ ⎯ ns Output start time after power down exit tPIO OUT Rise time or fall time of “OE” at 5 ns Load capacitance 15 pF ⎯ ⎯ 10 ns µs Note : The stabilization wait time of the modulation clock is required after the power is turned on or when the clock output enable setting (OE pin), multiplication setting (MLTP pin) or modulation rate setting (S1 pin and S0 pin) is changed. The stabilization wait time of the modulation clock takes the maximum value of Lock-Up time. 12 MB88162 ■ OUTPUT CLOCK DUTY CYCLE (tDCC = tb/ta) ta tb VDD × 0.8V VDD × 0.5V VDD × 0.2V OUT ■ INPUT FREQUENCY (fin = 1/tin) tin VDD × 0.8V VDD × 0.2V XIN ■ OUTPUT CLOCK RISE TIME/OUTPUT CLOCK FALL TIME (tr/tf) VDD × 0.8V VDD × 0.2V OUT tf tr ■ CYCLE-CYCLE JITTER (tJC = | tn − tn+1 |) OUT tn tn+1 Note : Cycle-cycle jitter indicates the difference between a certain cycle and the immediately succeeding (or preceding) cycle. 13 MB88162 ■ OUTPUT ENABLE “L” WIDTH (tOELW) tOELW OE VDD × 0.8V VDD × 0.2V ■ POWER SUPPLY RISE TIME (tVDR) tVDR 2.7/3.0V VDD 0.0V ■ OUTPUT Hi-Z START TIME AFTER POWER DOWN ENTRY (tPEZ) OE VDD × 0.2V tPEZ OUT Hi-Z ■ OUTPUT Hi-Z RELEASE TIME • OUTPUT START TIME AFTER POWER DOWN EXIT (tPIZ • tPIO) VDD × 0.8V OE tPIO tPIZ OUT 14 Hi-Z VDD × 0.2V MB88162 ■ MODULATION WAVEFORM • Modulation rate ±1.0%, example of center spread OUT output frequency + 1.0 % Frequency at modulation OFF Time − 1.0 % fMOD = 32 kHz (Typ) • Modulation rate −2.0%, example of down spread OUT output frequency Frequency at modulation OFF Time − 2.0 % fMOD = 32 kHz (Typ) 15 MB88162 ■ LOCK-UP TIME 2.7/3.0 V VDD Oscillation stabilization wait time XIN VIH OE Setting pin S1, S0, MLTP SPRD VIH tLK (lock-up time ) OUT The clock oscillation stabilization wait time is required when the power is turned on. If the OE pin is fixed at “H” level, the maximum time after the power is turned on until the required clock is obtained is (the oscillation stabilization wait time of input clock to XIN pin) + (the lock-up time “tLK”) . For the stabilization wait time of input clock to the XIN pin, check the characteristics of the resonator or oscillator used. VDD 2.7/3.0 V Oscillation stabilization wait time XIN VIH OE Setting pin S1, S0, MLTP SPRD VIH tLK (lock-up time ) OUT If the OE pin is used for power down control, the required clock is obtained at most the lock-up time “tLK” after the OE pin goes “H” level. 16 MB88162 XIN OE VIH Setting pin S1, S0, MLTP SPRD VIH VIL tLK (lock-up time ) tLK (lock-up time ) OUT If the setting pin (S1, S0, MLTP, or SPRD) is used for control during normal operation, the required clock is obtained at most the lock-up time “tLK” after the level at the pin is determined. Note : The wait time for the clock signal output from the OUT pin to become stable is required after the IC is released from power-down mode by the OE pin or after another pin’s setting is changed. During the period until the output clock signal becomes stable, the output frequency, output clock duty cycle, modulation period, and Cycle-Cycle jitter characteristic cannot be guaranteed. It is therefore advisable to perform processing such as cancelling a reset of the device at the succeeding stage after the lock-up time. 17 MB88162 ■ CRYSTAL OSCILLATION CIRCUIT The figure below shows the connection example about general crystal resonator. The oscillation circuit has the built-in feedback resistor (500kΩ) and oscillation stabilization capacitance (4 pF) . Because the value of oscillation stabilization capacitance must be adjusted to the most suitable value of the individual oscillator, add the capacitance (C1 and C2) to LSI external if necessary. 4 pF LSI Internal 4 pF Rf (500kΩ) XIN Pin XOUT Pin LSI External C2 C1 ■ INTERCONNECTION CIRCUIT EXAMPLE OE S0 15 14 13 12 11 10 VSS SPRD OUT 16 9 17 8 MB88162 18 XOUT XIN VDD 7 MLTP S1 1 2 3 4 5 6 R1 + C1 C1, C2 C3 C4 R1 18 C2 C4 C3 : Oscillation stabilization capacitance (see “■ CRYSTAL OSCILLATION CIRCUIT”.) : Capacitor of 10 µF or higher : Capacitor of about 0.01 µF (connect a capacitor of good high frequency property (ex. laminated ceramic capacitor) to close to this device) : Impedance matching resistor for board pattern MB88162 ■ ORDERING INFORMATION Part no. Package Emboss taping MB88162PVB-G-EFE1 18-pin plastic BCC (LCC-18P-M05) EF type MB88162PVB-G-ERE1 ER type 19 MB88162 ■ PACKAGE DIMENSION 18-pin plastic BCC (LCC-18P-M05) 15 2.70±0.10 (.106±.004) INDEX AREA 0.45±0.05 (.018±.002) (Mount height) 10 10 2.01(.079) TYP 2.40±0.10 (.094±.004) 0.45(.018) TYP. 1 0.075±0.025 (.003±.001) (Stand off) 6 2.31(.090) TYP 0.45(.018) TYP. 0.90(.035) REF 1.90(.075) REF "A" "B" "C" 6 15 1.35(.053) REF 1 2.28(.090) REF Details of "A" part 0.05(.002) 0.14(.006) MIN. Details of "B" part 0.25±0.06 (.010±.002) 0.25±0.06 (.010±.002) C C0.10(.004) Details of "C" part 0.36±0.06 (.014±.002) 0.28±0.06 (.011±.002) 0.36±0.06 (.014±.002) 0.28±0.06 (.011±.002) 2003 FUJITSU LIMITED C18058S-c-1-1 Dimensions in mm (inches) Note: The values in parentheses are reference values. 20 MB88162 FUJITSU LIMITED All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with FUJITSU sales representatives before ordering. The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose of reference to show examples of operations and uses of Fujitsu semiconductor device; Fujitsu does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating the device based on such information, you must assume any responsibility arising out of such use of the information. Fujitsu assumes no liability for any damages whatsoever arising out of the use of the information. Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of Fujitsu or any third party or does Fujitsu warrant non-infringement of any third-party’s intellectual property right or other right by using such information. Fujitsu assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would result from the use of information contained herein. The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite). Please note that Fujitsu will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Law of Japan, the prior authorization by Japanese government will be required for export of those products from Japan. F0602 © 2006 FUJITSU LIMITED Printed in Japan