FUJITSU MB89144AP-SH

FUJITSU SEMICONDUCTOR
DATA SHEET
DS07-12528-3E
8-bit Proprietary Microcontroller
CMOS
F2MC-8L MB89143A/144A Series
MB89143A/144A
■ DESCRIPTION
The MB89143A/144A has been developed as a general-purpose version of the F2MC-8L* family consisting of
proprietary 8-bit, single-chip microcontrollers.
In addition to a compact instruction set, the microcontrollers contain peripheral functions such as dual-clock
control system, five operating speed control stages, timers, a serial interface, an A/D converter, buzzer output,
high voltage driver, watch prescaler, and an external interrupt. The MB89143A/144A is applicable to a wide range
of applications from welfare products to industrial equipment.
*: F2MC stands for FUJITSU Flexible Microcontroller.
■ FEATURES
• Minimum execution time: 0.50 µs/8.0-MHz oscillation
• Interrupt servicing time: 4.50 µs/8.0-MHz oscillation
• F2MC-8L family CPU core
Multiplication and division instructions
Instruction set optimized for controllers
16-bit arithmetic operations
Test and branch instructions
Bit manipulation instructions, etc.
• Dual-clock control system
• High-voltage ports: 24 channel
(Continued)
■ PACKAGE
64-pin Plastic SH-DIP
(DIP-64P-M01)
MB89143A/144A
(Continued)
• Two types of timers
8/16-bit timer/counter (also usable as two 8-bit timers)
21-bit time-base timer
• One 8-bit serial interface
Switchable transfer direction allows communication with various equipment.
• 8-bit A/D converter: 8 channels
Successive approximation type
• External interrupt: 2 channels
Two channels are independent and capable of wake-up from low-power consumption modes. (Rising edge/
falling edge/both edges selectability)
–0.3 V to +7.0 V can be applied to INT1 (N-ch open-drain)
• Low-power consumption modes
Subclock mode (The main clock stops, and the device operates at the subclock.)
Watch mode (Only the watch prescaler is operating.)
Stop mode (Oscillation stops to minimize the current consumption.)
Sleep mode (The CPU stops to reduce the current consumption to approx. 1/3 of normal.)
• Watch prescaler
• Buzzer output
• Watchdog reset, reset output, and power-on reset functions
2
MB89143A/144A
■ PRODUCT LINEUP
Part number
Parameter
Classification
ROM size
RAM size
MB89143A
MB89144A
Mass production products
(mask ROM products)
8 K × 8 bits
12 K × 12 bits
256 × 8 bits
MB89P147
MB89PV140
One-time PROM
product
Piggyback/evaluation product
(for evaluation and development)
32 K × 8 bits
Internal PROM
32 K × 8 bits
External ROM
(Piggyback)
1 K × 8 bits
Internal
CPU functions
Number of instructions:
136
Instruction bit length:
8 bits
Instruction length:
1 to 3 bytes
Data bit length:
1, 8, 16 bits
Minimum execution time:
0.5 µs/8 MHz to 8.0 µs/8 MHz, 61 µs/32.768 kHz
Interrupt processing time:
4.5 µs/8 MHz to 72.0 µs/8 MHz, 562.5 µs/32.768 kHz
Note: The above times change according to the gear function.
Ports
High-voltage output ports (P-ch open-drain):
24 (P40 to P47, P50 to P57, and P60 to P67)
Buzzer output (P-ch open-drain, high-voltage):1
Output ports (CMOS):
4 (P20 to P23)
Input ports (CMOS):
2 (P70 and P71, function as X0A and X1A pins when
dual-clock system is used.)
I/O ports (CMOS):
23 (P00 to P07, P10 to P17, P30, and P32 to P37)
I/O port (N-channel open-drain): 1 (P31)
Total:
55
Time-base timer
Capable of generating four different intervals (at 8.0-MHz oscillation):
0.26 ms, 0.51 ms, 1.02 ms, and 0.524 s
8/16-bit timer
counter
8/16-bit timer operation (Operating clock, internal clock, external trigger)
8/16-bit event counter operation (Rising edge/falling edge/both edges selectability)
8-bit Serial I/O
8 bits
LSB first/MSB first selectability
One clock selectable from four transfer clocks
(one external shift clock, three internal shift clocks: 4, 8, 16 system clock cycles)
A/D converter
External interrupt
8-bit resolution × 8 channels
A/D conversion mode (with
conversion time of 22 µs/8 MHz, and
highest gear speed)
Continuous activation by external
activation capable
10-bit resolution × 12 channels
A/D conversion mode (with conversion time of 16.5 µs/
8 MHz, and highest gear speed)
Sense mode (with conversion time of 9.0 µs/8 MHz,
and highest gear speed)
Continuous activation enabled by external activation
capable
2 independent channels (edge selection, interrupt vector, source flag)
Rising edge/falling edge/both edges selectability
Built-in analog noise canceller
Used also for wake-up from stop/sleep mode. (Edge detection is also permitted in stop mode.)
Buzzer output
1.95 or 3.91 kHz selectable (at 8-MHz oscillation)
Output to a high-voltage pin
(Continued)
3
MB89143A/144A
(Continued)
Part number
Parameter
Watchdog reset
MB89143A
MB89144A
MB89P147
MB89PV140
Internal reset in 524 ms to 1049 ms (at 8 MHz oscillation) when the program runway occurs
8-bit PWM timer
None
12-bit MPG timer
8-bit timer operation/8-bit resolution PWM operation
12-bit resolution PWM operation/reload timer
operation/PPG operation
None
Standby mode
Sleep mode, stop mode, and watch mode
Process
CMOS
Package
DIP-64P-M01
MDP-64C-P02
EPROM for use
MBM27C256A-20
Operating voltage*
4.0 V to 6.0 V
2.7 V to 6.0 V
* : Varies with conditions such as the operating frequency. (See section “■ ELECTRICAL CHARACTERISTICS”.)
■ PACKAGE AND CORRESPONDING PRODUCTS
Package
MB89143A
MB89144A
MB89P147
×
DIP-64P-M01
MDP-64C-P02
: Available
MB89PV140
×
×
×: Not available
Note: For more information about each package, see section “■ PACKAGE DIMENSION”.
4
MB89143A/144A
■ DIFFERENCES AMONG PRODUCTS
1. Memory Size
Before evaluating using the piggyback product, verify its differences from the product that will actually be used.
Take particular care on the following points:
• On the MB89143A/144A, the upper half of the register bank cannot be used.
• The stack area etc. are set at the upper limit of the RAM.
2. Functions
Before evaluating using the piggyback product, verify its differences from the product that will actually be used.
Take particular care on the following point:
• The A/D converter in the MB89143A/144A is an 8-bit resolution type. The MB89143A/144A contains neither
the 8-bit PWM timer nor the 12-bit MPG timer.
3. Current Consumption
• In the case of the MB89PV140, add the current consumed by the EPROM which is connected to the top socket.
• When operated at low speed, the product with an OTPROM (one-time PROM) or an EPROM will consume
more current than the product with a mask ROM.
However, the current consumption in sleep/stop modes is the same. (For more information, see section
“■ ELECTRICAL CHARACTERISTICS”.)
4. Mask Options
Functions that can be selected as options and how to designate these options vary by the product. Before using
options check section “■ MASK OPTIONS”.
Take particular care on the following point:
• A pull-up resistor option is not provided for the MB89PV140.
5
MB89143A/144A
■ PIN ASSIGNMENT (MB89143A/4A only)
(Top view)
BZ
P67
P66
P65
P64
P63
P62
P61
P60
N.C.
P57
P56
P55
P54
P53
P52
P51
P50
P47
P46
P45
P44
P43
P42
P41
P40
P23
RST
MODA
X0
X1
VSS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
VCC
AVR
AVSS
P00/AN0
P01/AN1
P02/AN2
P03/AN3
P04/AN4
P05/AN5
P06/AN6
P07/AN7
P10
P11
P12
P13
P14
P15
P16
P17/ADST
P30/INT0
P31/INT1
P32/SCK
P33/SO
P34/SI
P35/EC
P36
P37
P20
P21
P22
P70/X0A
P71/X1A
Note: When used as general-purpose ports, the P70/X0A and P71/X1A function as input-only ports.
(DIP-64P-M01)
6
MB89143A/144A
■ PIN DESCRIPTION (MB89143A/4A only)
Pin no.
Pin name
SDIP*
30
X0
31
X1
29
28
Circuit type
Function
A
Main clock oscillator pins
Use a crystal oscillator.
MODA
B
Operating mode selection pin
Connect directly to VSS in normal operation.
RST
C
Reset I/O pin
This pin is an N-ch open-drain output type with a pull-up
resistor, and a hysteresis input type. “L” is output from
this pin by an internal reset source.
The internal circuit is initialized by the input of “L”.
This pin is with a noise canceller.
54 to 61
P07/AN7 to
P00/AN0
F
General-purpose I/O ports
These ports are a hysteresis input type. Also serve as an
analog input.
46
P17/ADST
H
General-purpose I/O port
This port is a hysteresis input type. Also serves as an
A/D converter external activation.
47 to 53
P16 to P10
H
General-purpose I/O ports
These ports are a hysteresis input type.
P70/X0A,
P71/X1A
J
Selectable either general-purpose input ports or the
subclock oscillator pins by the mask option. These ports
are a hysteresis input type when used as general-purpose
input ports.
P23 to P20
D
General-purpose output ports
38,
39
P37,
P36
H
General-purpose I/O ports
These ports are a hysteresis input type.
40
P35/EC
General-purpose I/O port
This port is a hysteresis input type. Also serves as the
external clock input for the 8/16-bit timer/counter.
41
P34/SI
General-purpose I/O port
This port is a hysteresis input type. Also serves as the
serial data input for the 8-bit serial interface.
42
P33/SO
General-purpose I/O port
This port is a hysteresis input type. Also serves as the
serial data output for the 8-bit serial interface.
43
P32/SCK
General-purpose I/O port
This port is a hysteresis input type. Also serves as the
serial transfer clock for the 8-bit serial interface.
34, 33
27,
35 to 37
* : DIP-64P-M01
(Continued)
7
MB89143A/144A
(Continued)
Pin no.
SDIP*
Circuit type
Function
44
P31/INT1
E
General-purpose I/O port
This port is an N-ch open-drain output and hysteresis
input type. Also serves as an external interrupt. The
interrupt input is a hysteresis input type and with a built-in
noise canceller.
45
P30/INT0
I
General-purpose I/O port
This port is a hysteresis input type. Also serves as an
external interrupt. The interrupt input is a hysteresis input
type and with a built-in noise canceller.
1
BZ
G
Buzzer output-only pin
P-ch high-voltage open-drain output port
P47 to P40,
P57 to P50,
P67 to P60
G
P-ch high-voltage open-drain output port
10
N.C.
—
Be sure to leave them open.
64
VCC
—
Power supply pin
Also serves as an A/D converter power supply.
32
VSS
—
Power supply (GND) pin
63
AVR
—
A/D converter reference voltage input pin
62
AVSS
—
A/D converter power supply pin
Use this pin at the same voltage as VSS.
19 to 26,
11 to 18,
2 to 9
* : DIP-64P-M01
8
Pin name
MB89143A/144A
■ I/O CIRCUIT TYPE
Type
Circuit
Remarks
A
• At an oscillation feedback resistor of approximately
1 MΩ/5.0 V
X1
X0
Standby control signal
B
• CMOS input
Hysteresis input
C
• At an output pull-up resistor (P-ch) of approximately
50 kΩ/5.0 V
• CMOS hysteresis input
R
P-ch
N-ch
Hysteresis input
D
• CMOS output
P-ch
N-ch
E
• N-ch open-drain output
• CMOS hysteresis input
• The interrupt input is with a noise canceller.
N-ch
Port
Hysteresis input
Interrupt input
With noise canceller
F
• CMOS output
• CMOS hysteresis input
P-ch
N-ch
Port
Hysteresis input
Analog input
(Continued)
9
MB89143A/144A
(Continued)
Type
Circuit
Remarks
G
• P-ch high-voltage open-drain output
P-ch
H
• CMOS output
• CMOS hysteresis input
• Pull-up resistor optional
(Only for P14 to P17 and P32 to P37)
P-ch
P-ch
N-ch
Port
Hysteresis input
I
• CMOS output
• CMOS hysteresis input
• The interrupt input is with a noise canceller.
P-ch
N-ch
Port
Interrupt input
Hysteresis input with noise canceller
J
X1A
Port
Hysteresis input
X0A
Standby control signal
Port
Hysteresis input
10
• The oscillation feedback resistor is not provided.
• CMOS hysteresis input when subclock is not used
MB89143A/144A
■ HANDLING DEVICES
1. Preventing Latchup
Latchup may occur on CMOS ICs if voltage higher than VCC or lower than VSS is applied to input and output pins
other than medium- to high-voltage pins or if higher than the voltage which shows on “1. Absolute Maximum
Ratings” in section “■ ELECTRICAL CHARACTERISTICS” is applied between VCC and VSS. (However, up to
7.0 V can be applied to P31/INT1 pin, regardless of VCC.)
When latchup occurs, power supply current increases rapidly and might thermally damage elements. When
using, take great care not to exceed the absolute maximum ratings.
Also, take care to prevent the analog power supply (AVR) and analog input from exceeding the digital power
supply (VCC) when the analog system power supply is turned on and off.
2. Treatment of Unused Input Pins
Leaving unused input pins open could cause malfunctions. They should be connected to a pull-up or pull-down
resistor.
3. Treatment of Power Supply Pins on Microcontrollers with A/D and D/A Converters
Connect to be AVSS = AVR = VSS even if the A/D and D/A converters are not in use.
4. Treatment of N.C. Pins
Be sure to leave (internally connected) N.C. pins open.
5. Power Supply Voltage Fluctuations
Although VCC power supply voltage is assured to operate within the rated range, a rapid fluctuation of the voltage
could cause malfunctions, even if it occurs within the rated range. Stabilizing voltage supplied to the IC is therefore
important. As stabilization guidelines, it is recommended to control power so that VCC ripple fluctuations (P-P
value) will be less than 10% of the standard VCC value at the commercial frequency(50 to 60 Hz) and the transient
fluctuation rate will be less than 0.1 V/ms at the time of a momentary fluctuation such as when power is switched.
6. Precautions when Using an External Clock
Even when an external clock is used, oscillation stabilization time is required for power-on reset and wake-up
from stop mode.
11
MB89143A/144A
■ BLOCK DIAGRAM (MB89143A/4A only)
Main clock oscillator
(Max. 8 MHz)
X0
X1
BZ
Buzzer output
Clock controller
High-voltage port 6
P60 to P67
Subclock oscillator
(32.768 kHz)
Port 7
P70/X0A
P71/X1A
8
High-voltage port 5
8
P50 to P57
P20 to P23
4
Port 2
CMOS output port
Internal bus
CMOS input port
High-voltage port 4
8
P40 to P47
Time-base timer
CMOS I/O port
8
8-bit serial interface
AVR
7
CMOS I/O port 1
RAM
(256 × 8 bits)
F2MC-8L
CPU
ROM
Note: The A/D converter is an 8-bit, 8-channel type.
8/16-bit timer/
counter
P35/EC
P30/INT0
External interrupt
Port 3
P17/ADST
12
P32/SCK
P33/SO
P34/SI
8-bit A/D converter
AVSS
P10 to P16
Port 3
CMOS I/O port 0
P07/AN7
to P00/AN0
N-ch open-drain port
Other pins
V CC , V SS , M O D A , R S T
P31/INT1
MB89143A/144A
■ CPU CORE
1. Memory Space
The microcontrollers of the MB89143A/144A series offer a memory space of 64 Kbytes for storing all of I/O,
data, and program areas. The I/O area is located at the lowest address. The data area is provided immediately
above the I/O area. The data area can be divided into register, stack, and direct areas according to the application.
The program area is located at exactly the opposite end, that is, near the highest address. Provide the tables
of interrupt reset vectors and vector call instructions toward the highest address within the program area. The
memory space of the MB89143A/144A series is structured as illustrated below.
MB89143A
0000 H
MB89144A
0000 H
I/O
0080 H
I/O
0080 H
RAM
256
0100 H
RAM
256
0100 H
Register
0180H
Register
0180H
Not available
Not available
D000 H
E000 H
ROM
12 KB
ROM
8 KB
FFFF H
FFFF H
13
MB89143A/144A
2. Registers
The F2MC-8L family has two types of registers; dedicated registers in the CPU and general-purpose registers
in the memory. The following dedicated registers are provided:
Program counter (PC):
A 16-bit register for indicating instruction storage positions
Accumulator (A):
A 16-bit temporary register for storing arithmetic operations, etc. When the
instruction is an 8-bit data processing instruction, the lower byte is used.
Temporary accumulator (T):
A 16-bit register which performs arithmetic operations with the accumulator
When the instruction is an 8-bit data processing instruction, the lower byte is used.
Index register (IX):
A 16-bit register for index modification
Extra pointer (EP):
A 16-bit pointer for indicating a memory address
Stack pointer (SP):
A 16-bit register for indicating a stack area
Program status (PS):
A 16-bit register for storing a register pointer, a condition code
Initial value
16 bits
FFFDH
: Program counter
PC
A
: Accumulator
Undefined
T
: Temporary accumulator
Undefined
IX
: Index register
Undefined
EP
: Extra pointer
Undefined
SP
: Stack pointer
Undefined
PS
: Program status
I-flag = 0, IL1, 0 = 1, 1
Other bits are undefined.
The PS can further be divided into higher 8 bits for use as a register bank pointer (RP) and the lower 8 bits for
use as a condition code register (CCR). (See the diagram below.)
Structure of the Program Status Register
15
PS
14
13
12
10
9
8
Vacancy Vacancy Vacancy
RP
RP
14
11
7
6
H
I
5
4
IL1, 0
3
2
1
0
N
Z
V
C
CCR
MB89143A/144A
The RP indicates the address of the register bank currently in use. The relationship between the pointer contents
and the actual address is based on the conversion rule illustrated below.
Rule for Conversion of Actual Addresses of the General-purpose Register Area
RP
Lower OP codes
“0” “0” “0” “0” “0” “0” “0” “1” R4 R3 R2 R1 R0 b2
↓
↓
↓
↓
↓
↓
↓
↓
↓
↓
↓
↓
↓
↓
b1
b0
↓
↓
Generated addresses A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0
The CCR consists of bits indicating the results of arithmetic operations and the contents of transfer data and
bits for control of CPU operations at the time of an interrupt.
H-flag: Set when a carry or a borrow from bit 3 to bit 4 occurs as a result of an arithmetic operation. Cleared
otherwise. This flag is for decimal adjustment instructions.
I-flag:
Interrupt is allowed when this flag is set to 1. Interrupt is prohibited when the flag is set to 0. Set to 0
when reset.
IL1, 0:
Indicates the level of the interrupt currently allowed. Processes an interrupt only if its request level is
higher than the value indicated by this bit.
IL1
IL0
Interrupt level
0
0
0
1
1
0
2
1
1
3
1
High-low
High
Low = no interrupt
N-flag: Set if the MSB is set to 1 as the result of an arithmetic operation. Cleared when the bit is set to 0.
Z-flag:
Set to 1 when an arithmetic operation results in 0. Cleared otherwise.
V-flag:
Set to 1 if the complement on 2 overflows as a result of an arithmetic operation. Reset if the overflow does
not occur.
C-flag: Set to 1 when a carry or a borrow from bit 7 occurs as a result of an arithmetic operation.
Cleared otherwise.
Set to the shift-out value in the case of a shift instruction.
15
MB89143A/144A
The following general-purpose registers are provided:
General-purpose registers: An 8-bit register for storing data
The general-purpose registers are 8 bits and located in the register banks of the memory. One bank contains
eight registers and up to a total of 16 banks can be used on the MB89143A/144A. The bank currently in use is
indicated by the register bank pointer (RP).
Register Bank Configuration
This address = 0100H + 8 × (RP)
R0
R1
R2
R3
R4
R5
R6
R7
16 banks
Memory area
16
MB89143A/144A
■ I/O MAP
Address
Read/write
Register name
00H
(R/W)
PDR0
Port 0 data register
01H
(W)
DDR0
Port 0 data direction register
02H
(R/W)
PDR1
Port 1 data register
03H
(W)
DDR1
Port 1 data direction register
04H
(R/W)
PDR2
Port 2 data register
05H, 06H
Register description
Vacancy
07H
(R/W)
SYCC
System clock control register
08H
(R/W)
STBC
Standby control register
09H
(R/W)
WDTE
Watchdog timer control register
0AH
(R/W)
TBCR
Time-base timer control register
0BH
(R/W)
WPCR
Watch prescaler control register
0CH
(R/W)
PDR3
Port 3 data register
0DH
(W)
DDR3
Port 3 data direction register
0EH
(R/W)
BUZR
Buzzer register
0FH
(R/W)
EIC
10H
(R/W)
PDR4
Port 4 data register
11H
(R/W)
PDR5
Port 5 data register
12H
(R/W)
PDR6
Port 6 data register
13H
(R)
PDR7
Port 7 data register
14H to 17H
External interrupt control register
Vacancy
18H
(R/W)
T3CR
Timer 3 control register
19H
(R/W)
T2CR
Timer 2 control register
1AH
(R/W)
T3DR
Timer 3 data register
1BH
(R/W)
T2DR
Timer 2 data register
1CH
(R/W)
SMR
Serial mode register
1DH
(R/W)
SDR
Serial data register
1EH
(R/W)
ADC1
A/D converter control register 1
1FH
(R/W)
ADC2
A/D converter control register 2
20H
(R/W)
ADDH
A/D data register (H)
21H
(R/W)
ADDL
A/D data register (L)
22H
(W)
PCR0
Port input control register 0
23H
(W)
PCR1
Port input control register 1
24H to 7BH
Vacancy
7CH
(W)
ILR1
Interrupt level setting register 1
7DH
(W)
ILR2
Interrupt level setting register 2
7EH
(W)
ILR3
Interrupt level setting register 3
7FH
Vacancy
Note: Do not use vacancies.
17
MB89143A/144A
■ ELECTRICAL CHARACTERISTICS (MB89143A/4A only)
1. Absolute Maximum Ratings
(AVSS = VSS = 0.0 V)
Parameter
Symbol
Rating
Unit
Remarks
Min.
Max.
VCC
AVR
VSS – 0.3
VSS + 7.0
V
AVR ≤ VCC +0.3*1
VI1
VSS – 0.3
VCC + 0.3
V
P00 to P07, P10 to P17, P30,
P32 to P37, P70, P71
VI2
VSS – 0.3
7
V
P31
VI3
VCC – 40
VCC + 0.3
V
P40 to P47, P50 to P57,
P60 to P67, BZ*2
VO1
VSS – 0.3
VCC + 0.3
V
P00 to P07, P10 to P17,
P20 to P23, P30 to P37
VO2
—
VCC + 0.3
V
P40 to P47, P50 to P57,
P60 to P67, BZ*2
“H” level total maximum
output current
ΣIOH
—
–100
mA
“H” level total average
output current
ΣIOHAV
—
–75
mA
“H” level maximum output
current
IOH
—
–12
“H” level average output
current
IOHAV
—
–6
“H” level maximum output
current
IOH
—
–20
“H” level average output
current
IOHAV
—
–10
“L” level total maximum
output current
ΣIOL
—
50
mA
“L” level total average
output current
ΣIOLAV
—
30
mA
Average value (operating
current × operation rate)
“L” level maximum output
current
IOL
—
12
“L” level average output
current
mA
IOLAV
—
6
P00 to P07, P10 to P17,
P20 to P23, P30 to P37
Power consumption
PD
—
470
mW
SH-DIP64: DIP-64P-M01
Operating temperature
TA
–40
+85
°C
Storage temperature
Tstg
–55
+150
°C
Power supply voltage
Input voltage
Output voltage
mA
mA
Average value (operating
current × operation rate)
P00 to P07, P30, P32 to P37,
P10 to P17, P20 to P23
Average value (operating
current × operation rate)
P40 to P47, P50 to P57,
P60 to P67, BZ
Average value (operating
current × operation rate)
*1: Take care so that AVR does not exceed VCC + 0.3 V, and does not exceed VCC when power is turned on.
*2: VI and VO must not exceed VCC + 0.3 V.
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
18
MB89143A/144A
2. Recommended Operating Conditions
(AVSS = VSS = 0.0 V)
Parameter
Value
Unit
Remarks
6.0*
V
Normal operation assurance range*
at highest gear speed
3.5*
6.0*
V
Normal operation assurance range*
at highest gear speed
2.5
6.0
V
When in watch mode or subclock
operation mode
1.5
6.0
V
Retains the RAM state in stop mode
AVR
0.0
VCC
V
TA
–40
+85
°C
Symbol
Power supply voltage
VCC
A/D converter reference input voltage
Operating temperature
Min.
Max.
4.0*
* : These values vary with the operating frequency, instruction cycle, and analog assurance range. See Figure 1
and “5. A/D Converter Electrical Characteristics.”
6
Operating voltage (V)
5
Operation assurance range
4
3
2
1
2
3
4
5
6
7
9
8
10
Main clock operating frequency (at an instruction cycle of 4/FCH) (MHz)
2.0
1.3
1.0
0.8
0.66 0.57
Minimum execution time (instruction cycle)
Figure 1
0.5
0.44
0.4
(µs)
Operating Voltage vs. Main Clock Operating Frequency
Figure 1 indicates the operating frequency of the external oscillator at an instruction cycle of 4/FCH.
Since the operating voltage range is dependent on the instruction cycle, see minimum execution time if the
operating speed is switched using a gear.
WARNING: The recommended operating conditions are required in order to ensure the normal operation of the
semiconductor device. All of the device’s electrical characteristics are warranted when the device is
operated within these ranges.
Always use semiconductor devices within their recommended operating condition ranges. Operation
outside these ranges may adversely affect reliability and could result in device failure.
No warranty is made with respect to uses, operating conditions, or combinations not represented on
the data sheet. Users considering application outside the listed conditions are advised to contact their
FUJITSU representatives beforehand.
19
MB89143A/144A
3. DC Characteristics
Parameter
Symbol
Pin
(AVR = VCC = 5.0 V, AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Value
Condition
Unit Remarks
Min.
Typ.
Max.
“H” level input
VIHS
voltage
P00 to P07,
P10 to P17,
P30 to P37,
P70, P71,
X0, RST,
X1, MODA
—
0.8 VCC
—
VCC + 0.3
V
“L” level input
voltage
VILS
P00 to P07,
P10 to P17,
P30 to P37,
P70, P71,
X0, RST,
X1, MODA
—
VSS – 0.3
—
0.2 VCC
V
Open-drain
output pin
application
voltage
VD1
P31
—
VSS – 0.3
—
7.0
V
VOH1
P00 to P07,
P10 to P17,
P20 to P23,
P30 to P37
IOH = –2.0 mA
2.4
—
—
V
VOH2
P40 to P47,
P50 to P57,
P60 to P67
IOH = –10 mA
3.0
—
—
V
P00 to P07,
P10 to P17,
P20 to P23,
P30 to P37
IOL = 1.8 mA
—
—
0.4
V
VOL2
RST
IOL = 4.0 mA
—
—
0.6
V
ILI1
P00 to P07,
P10 to P17,
P30 to P37,
P70, P71
0 V < V1 < VCC
—
—
±5
µA
Except pins
with pull-up
resistor
ILI2
P14 to P17,
P32 to P37
VI = 0.0 V
–200
–100
–50
µA
Only for pins
with pull-up
resistor
Output leakage
current
ILO1
P40 to P47,
P50 to P57,
P60 to P67
VI = VCC – 35 V
—
—
–10
µA
Pull-up
resistance
RPULL
RST,
P14 to P17,
P32 to P37
VI = 0.0 V
25
50
100
kΩ
VCC
FCH = 8 MHz,
VCC = 5.0 V,
tinst = 0.5 µs,
when A/D conversion is
stopped
—
9
15
mA
“H” level
output voltage
VOL1
“L” level
output voltage
Input leakage
current
Power supply
current
ICC1
Except P31
Note: The power supply current is measured at the external clock.
(Continued)
20
MB89143A/144A
(Continued)
Parameter
Symbol
Pin
FCH = 8 MHz,
VCC = 3.5 V,
tinst = 8.0 µs,
when A/D conversion is
stopped
—
1.5
2
mA
FCH = 8 MHz
VCC = 5.0 V
tinst = 0.5 µs
—
3
7
mA
FCH = 8 MHz
VCC = 3.5 V
tinst = 8.0 µs
—
1
1.5
mA
ICCL
FCL = 32.768 kHz
VCC = 3.0 V
Subclock mode
—
50
150
µA
ICCLS
FCL = 32.768 kHz
VCC = 3.0 V
Subclock mode
—
25
50
µA
ICCT
FCL = 32.768 kHz
VCC = 3.0 V
• Watch mode
• Main clock stop mode
at dual-clock system
—
3
15
µA
ICCH
FCL = 32.768 kHz
TA = +25°C
• Subclock stop mode
• Main clock stop mode
at single-clock system
—
—
10
µA
ICCA
FCH = 8 MHz,
VCC = 5.0 V,
TA = +25°C,
tinst = 0.5 µs,
when A/D conversion is
activated
—
11.5
19.5
mA
IR
FCH = 8 MHz,
TA = +25°C,
when A/D conversion is
activated
—
200
—
µA
FCH = 8 MHz,
TA = +25°C,
when A/D conversion is
stopped
—
—
10
µA
f = 1 MHz
—
10
—
pF
Sleep mode
ICC2
ICCS1
ICCS2
VCC
Power supply
current
AVR
IRH
Input
capacitance
(AVR = VCC = 5.0 V, AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Value
Condition
Unit Remarks
Min.
Typ.
Max.
CIN
Other than
AVSS, AVR,
VCC, and VSS
When the gear
function is
used, the power
supply current
varies with the
measurement
point.
Note: The power supply current is measured at the external clock.
21
MB89143A/144A
4. AC Characteristics
(1) Reset Timing
Parameter
Symbol
(AVR = VCC = 5.0 V±10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Value
Condition
Unit
Remarks
Min.
Typ.
Max.
RST “L” pulse width
tZLZH
—
48 tXCYL
—
—
ns
RST noise limit width
tZLNC
—
20
40
60
ns
Note: tXCYL is the oscillation cycle (1/FCH) to input to the X0 pin.
tZLZH
tZLNC
RST
0.2 VCC
0.2 VCC
(2) Power-on Reset
(AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Parameter
Symbol
Condition
Value
Min.
Max.
Unit
Remarks
Power supply rising
time
tR
—
—
50
ms
Power-on reset function
only
Power supply cut-off
time
tOFF
—
1
—
ms
Due to repeated
operations
Note: Make sure that power supply rises within the selected oscillation stabilization time.
If power supply voltage needs to be varied in the course of operation, a smooth voltage rise is
recommended.
tR
tOFF
2.0 V
0.2 V
VCC
22
0.2 V
0.2 V
MB89143A/144A
(3) Clock Timing
Parameter
Symbol
Clock frequency
Clock cycle time
Input clock pulse
width
Input clock rising/
falling time
Pin
(AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Value
Unit
Remarks
Typ.
Max.
Condition
Min.
FCH
X0, X1
—
2
—
8
MHz
FCL
X0A, X1A
—
—
32.768
—
kHz
tXCYL
X0, X1
—
125
—
500
ns
tLXCYL
X0A, X1A
—
—
30.5
—
µs
PWH
PWL
X0
—
30
—
—
ns
PWHL
PWLL
X0A
—
—
15.2
—
ns
tCR
tCF
X0, X0A
—
—
—
10
ns
External clock
External clock
X0 and X1 Timings and Conditions
tXCYL
PWH
PWL
tCR
tCF
0.8 VCC
0.8 VCC
X0
0.2 VCC
0.2 VCC
0.2 VCC
Main Clock Conditions
When a crystal
or
ceramic resonator is used
X0
X1
When an external clock is used
X0
X1
Open
C0
C1
23
MB89143A/144A
X0A and X1A Timings and Conditions
tLXCYL
PWHL
PWLL
tCF
tCR
0.8 VCC
0.8 VCC
X0A
0.2 VCC
0.2 VCC
0.2 VCC
Subclock Conditions
When a crystal
or
ceramic resonator is used
X0A
When an external clock is used
X0A
X1A
X1A
Open
RF
C0
RD
C1
Note: The subclock oscillator feedback resistor is connected externally in dual-clock products.
(4) Instruction Cycle
Parameter
Symbol
Value (typical)
Unit
Remarks
4/FCH, 8/FCH, 16/FCH, 32/FCH
µs
(4/FCH) tinst = 0.5 µs when operating at FCH =
8 MHz
2/FCL
µs
tinst = 61.036 µs when operating at FCL =
32.768 kHz
Instruction cycle time tinst
Note: When operating at 8 MHz, the cycle varies with the set execution time.
24
MB89143A/144A
(5) Serial I/O timing
Parameter
Symbol
Pin
(AVR = VCC = 5.0 V±10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Value
Condition
Unit Remarks
Min.
Max.
2 tinst*
—
µs
–200
200
ns
1/2 tinst*
—
µs
1/2 tinst*
—
µs
1 tinst*
—
µs
1 tinst*
—
µs
0
200
ns
SI, SCK
1/2 tinst*
—
µs
SCK, SI
1/2 tinst*
—
µs
Serial clock cycle time
tSCYC
SCK
SCK ↓ → SO time
tSLOV
SCK, SO
Valid SI → SCK ↑
tIVSH
SI, SCK
SCK ↑ → valid SI hold time tSHIX
SCK, SI
Serial clock “H” pulse
width
tSHSL
SCK
Serial clock “L” pulse
width
tSLSH
SCK
SCK ↓ → SO time
tSLOV
SCK, SO
Valid SI → SCK ↑
tIVSH
SCK ↑ → valid SI hold time tSHIX
Internal shift
clock mode
External shift
clock mode
* : For information on tinst, see “(4) Instruction Cycle.”
Internal Shift Clock Mode
tSCYC
SCK
2.4 V
0.8 V
0.8 V
tSLOV
2.4 V
SO
0.8 V
tIVSH
SI
tSHIX
0.8 VCC
0.8 VCC
0.2 VCC
0.2 VCC
External Shift Clock Mode
tSLSH
SCK
SO
tSHSL
0.8 VCC
0.2 VCC
tSLOV
2.4 V
0.8 V
tIVSH
SI
0.8 VCC
0.2 VCC
tSHIX
0.8 VCC
0.8 VCC
0.2 VCC
0.2 VCC
25
MB89143A/144A
(6) Peripheral Input Timing
(AVR = VCC = 5.0 V±10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Parameter
Symbol
Pin
Value
Condition
Min.
Max.
Unit
Peripheral input “H”
pulse width 1
tILIH1
EC, ADST,
INT0 to INT1
—
2 tinst
—
µs
Peripheral input “L”
pulse width 1
tIHIL1
EC, ADST,
INT0 to INT1
—
2 tinst
—
µs
tIHIL1
INT0 to INT1,
EC,
ADST
Remarks
tILIH1
0.8 VCC
0.8 VCC
0.2 VCC
0.2 VCC
(7) Peripheral Input Noise Limit Width
(AVR = VCC = 5.0 V±10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Parameter
Symbol
Value
Pin
Min.
Typ.
Max.
Unit
Peripheral input “H”
level noise limit width 1
tIHNC1
INT1, INT0
50
100
250
ns
Peripheral input “L”
level noise limit width 1
tILNC1
INT1, INT0
50
100
250
ns
Remarks
Note: The minimum values is always canceled, while values over the maximum value are not canceled.
tILNC1
tIHNC1
INT0, INT1
0.8 VCC
0.2 VCC
26
0.2 VCC
0.8 VCC
MB89143A/144A
5. A/D Converter Electrical Characteristics
Parameter
Symbol
(VCC = 5.0 V±10%, AVSS = VSS = 0.0 V, FCH = 8 MHz, TA = –40°C to +85°C)
Value
Condition
Unit Remarks
Pin
Min.
Typ.
Max.
Resolution
—
—
—
—
—
8
bit
Total error
—
—
—
—
—
±3.0
LSB
Linearity error
—
—
—
—
—
±1.0
LSB
Differential linearity
error
—
—
—
—
—
±0.9
LSB
Zero transition
voltage
VOT
AN0 to AN7
—
AVSS – 1.5 LSB
AVSS + 0.5 LSB
AVSS + 2.5 LSB
mV
Full-scale transition
voltage
VFST
AN0 to AN7
—
AVR – 3.5 LSB
AVR – 1.5 LSB
AVR + 0.5 LSB
mV
Interchannel
disparity
—
—
—
—
—
1.0
LSB
A/D conversion time
—
—
—
—
44 tinst
—
µs
Sense mode
conversion time
—
—
—
—
12 tinst
—
µs
—
—
10
µA
Analog port input
current
IAIN
=
AN0 to AN7 AVR
VCC = 5.0 V
Analog input voltage
—
AN0 to AN7
—
0
—
AVR
V
Reference voltage
—
AVR
—
4.5
—
VCC
V
AVR
AVR = 5.0 V
—
200
—
µA
Reference-voltage
supply current
IR
Notes: • The smaller the | AVR – AVSS |, the greater the error would become relatively.
• The output impedance of the external circuit for the analog input must satisfy the following conditions:
Output impedance of the external circuit < Approx. 10 kΩ
If the output impedance of the external circuit is too high, an analog voltage sampling time might be
insufficient (sampling time = 22 µs at 8 MHz oscillation).
Analog Input Equivalent Circuit
Sample hold circuit
.
C =. 33 pF
Analog input pin
Comparator
If the analog input
impedance is 10 kΩ
or more, it is
recommended to
connect an external
capacitor of approx.
0.1 µF.
.
R =. 6 kΩ
Close for 8 instruction cycles after
activating A/D conversion.
Analog channel selector
27
MB89143A/144A
6. A/D Glossary
• Resolution
Analog changes that are identifiable with the A/D converter
• Linearity error
The deviation of the straight line connecting the zero transition point (“0000 0000” ↔ “0000 0001”) with the
full-scale transition point (“1111 1111” ↔ “1111 1110”) from actual conversion characteristics
• Differential linearity error
The deviation of input voltage needed to change the output code by 1 LSB from the theoretical value
• Total error
The difference between actual and theoretical value
This error is caused by the zero transition error, full-scale transition error, linearity error, quantization error,
and noise.
Theoretical I/O characteristics
1111 1111
1111 1110
Theoretical conversion
value
1 LSB =
Digital output
Actual conversion
value
AVR
256
Linearity error =
(1 LSB
× N + VOT)
Differential linearity error =
Linearity error
0000 0010
Total error =
VNT − (1 LSB × N + VOT)
1 LSB
V(N+1)T − VNT
1 LSB
VNT − (1 LSB × N + 0.5 LSB)
1 LSB
0000 0001
0000 0000
VOT
VNT V(N+1)T
Analog input
28
VFST
−1
MB89143A/144A
■ MASK OPTIONS
No.
Part number
Parameter
MB89143A/144A
Specification method
Specify when
ordering masking
MB89PV140
101
102
MB89P147V1
Set in EPROM
1
Clock mode selection
Single-clock mode
Dual-clock mode
Can be set
Single clock Dual clock
2
Pull-up resistors
P14 to P17,
P32 to P37
Specify by pin
Without pull- Without pullCan be set per pin
up resistor
up resistor
3
Power-on reset
With
Without
With power-on rest
With power- With powerCan be set
on reset
on reset
4
Reset output
With
Without
Can be set
With reset
output
5
Pull-down resistors
P40 to P47
P50 to P57
P60 to P67
Without pull-down
resistor
Without pull- Without pullWithout pull-down
down
down
resistor
resistor
resistor
With reset
output
Can be set
Can be set
■ ORDERING INFORMATION
Part number
MB89143AP-SH
MB89144AP-SH
MB89P147V1P-SH
Package
Remarks
64-pin Plastic SH-DIP
(DIP-64P-M01)
29
MB89143A/144A
■ PACKAGE DIMENSION
Note: Pins width and pins thickness include plating thickness.
64-pin Plastic SH-DIP
(DIP-64P-M01)
+0.22
+.009
58.00 –0.55 2.283 –.022
INDEX-1
17.00±0.25
(.669±.010)
INDEX-2
+0.70
4.95 –0.20
+.028
.195 –.008
+0.50
0.70 –0.19
+.020
.028 –.007
0.27±0.10
(.011±.004)
+0.20
3.30 –0.30
.130
+.008
–.012
+0.40
1.378 –0.20
.0543
C
30
+.016
–.008
2001 FUJITSU LIMITED D64001S-c-4-5
1.778(.0700)
0.47±0.10
(.019±.004)
19.05(.750)
+0.50
0.25(.010)
M
1.00 –0
.039
+.020
–.0
0~15°
Dimensions in mm (inches)
MB89143A/144A
FUJITSU LIMITED
All Rights Reserved.
The contents of this document are subject to change without notice.
Customers are advised to consult with FUJITSU sales
representatives before ordering.
The information and circuit diagrams in this document are
presented as examples of semiconductor device applications, and
are not intended to be incorporated in devices for actual use. Also,
FUJITSU is unable to assume responsibility for infringement of
any patent rights or other rights of third parties arising from the use
of this information or circuit diagrams.
The products described in this document are designed, developed
and manufactured as contemplated for general use, including
without limitation, ordinary industrial use, general office use,
personal use, and household use, but are not designed, developed
and manufactured as contemplated (1) for use accompanying fatal
risks or dangers that, unless extremely high safety is secured, could
have a serious effect to the public, and could lead directly to death,
personal injury, severe physical damage or other loss (i.e., nuclear
reaction control in nuclear facility, aircraft flight control, air traffic
control, mass transport control, medical life support system, missile
launch control in weapon system), or (2) for use requiring
extremely high reliability (i.e., submersible repeater and artificial
satellite).
Please note that Fujitsu will not be liable against you and/or any
third party for any claims or damages arising in connection with
above-mentioned uses of the products.
Any semiconductor devices have an inherent chance of failure. You
must protect against injury, damage or loss from such failures by
incorporating safety design measures into your facility and
equipment such as redundancy, fire protection, and prevention of
over-current levels and other abnormal operating conditions.
If any products described in this document represent goods or
technologies subject to certain restrictions on export under the
Foreign Exchange and Foreign Trade Law of Japan, the prior
authorization by Japanese government will be required for export
of those products from Japan.
F0107
 FUJITSU LIMITED Printed in Japan