CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CG Chip Type, Higher Capacitance series Higher Capacitance, Low ESR, High ripple current. Load life of 2000 hours at 105°C. SMD type : Lead free reflow soldering condition at 260°C peak correspondence. Adapted to the RoHS directive (2002/95/EC). CG Higher Capacitance CF Specifications Item Performance Characteristics Category Temperature Range –55 to +105°C Rated Voltage Range 2.5 to 16V Rated Capacitance Range 47 to 3300µF Capacitance Tolerance ± 20% at 120Hz, 20°C tan δ Not more than value of Standard ratings at 120Hz, 20°C ESR ( 1) Not more than value of Standard ratings at 100kHz, 20°C Leakage Current ( 2) Not more than value of Standard ratings. After 2 minute's application of rated voltage. Characteristics of Temperature Z+105°C / Z+20°C 1.25 Impedance Ratio 1.25 Z - 55°C / Z + 20°C 20°C (100kHz) Capacitance change Within ± 20% of initial value ( 3) tan δ 150% or less of the initial specified value ESR ( 1) 150% or less of the initial specified value Leakage current ( 2) Initial specified value or less Capacitance change Within ± 20% of initial value ( 3) tan δ 150% or less of the initial specified value ESR ( 1) 150% or less of the initial specified value Leakage current ( 2) Initial specified value or less In the case of peak temp, less than 250°C, Capacitance change Within ± 10% of initial value ( 3) Resistance to reflow soldering shall be within two times. tan δ 130% or less of the initial specified value Soldering Heat In the case of peak temp, less than 260°C, ESR ( 1) 130% or less of the initial specified value reflow soldering shall be once. Leakage current ( 2) Initial specified value or less After 2000 hours' application of rated voltage Endurance at 105°C, capacitors meet the specified value for life characteristics listed at right. After 1000 hours' application of rated voltage Damp Heat at 60°C 90%RH, capacitors meet the specified value for life characteristics listed at right. To comply with recommended conditions for reflow soldering. Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec. Measurement for solder temperature profile shall be made at the capacitor top and the terminal. Marking Navy blue print on the case top. 1 ESR measurements should be made at a point on the terminal nearest where the ternimals protrude through the plastic platform. 2 Conditioning : If there is doubt about the measured result, measurement should be made again after the rated voltage is applied for 120 minutes at the temperature of 105°C. 3 Initial value : The value before test of examination of resistance to soldering. CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS series Dimensions L Lot No. C± 0.2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PCG 0 J 4 7 1 MC L 1 GS E B±0.2 CG 470 j 741 Series φD+0.5 MAX. Voltage ( j:6.3V ) Capacitance Type numbering system (Example : 6.3V 470µF) 0.5 MAX. Positive Plastic platform 0.3 MAX. A±0.2 CG Taping code Configuration +0.1 - 0.4 Capacitance tolerance (±20%) Negative Rated Capacitance (470µF) H (mm) Rated voltage (6.3V) Size φ5 × 6L φ6.3 × 6L φ8 × 7L φ10 × 8L φ10 × 10L φ10 × 12.7L φD 5.0 6.3 8.0 10.0 10.0 10.0 Series name L 5.9 5.9 6.9 7.9 9.9 12.6 Type A 6.0 7.3 9.0 11.0 11.0 11.0 B 5.3 6.6 8.3 10.3 10.3 10.3 C 5.3 6.6 8.3 10.3 10.3 10.3 E 1.2 2.1 3.2 4.6 4.6 4.6 H 0.5 ~ 0.8 0.5 ~ 0.8 0.8 ~ 1.1 0.8 ~ 1.1 0.8 ~ 1.1 0.8 ~ 1.1 Voltage V Code 2.5 e 4 g 6.3 j 10 A 16 C Standard ratings Rated Voltage (V) Code 2.5 (0E) 4 (0G) 6.3 (0J) 10 (1A) Surge Voltage (V) 2.8 4.6 7.2 11.5 Rated Capacitance (µF) 18.4 tan δ Leakage Current (µA) ESR (mΩ) (20˚C / 100kHz) Rated ripple (mArms) (105˚C / 100kHz) Code 220 5×6 0.12 110 30 2100 PCG0E221MCL1GS 470 6.3 × 6 0.12 235 20 2900 PCG0E471MCL1GS 560 6.3 × 6 0.12 280 20 3000 PCG0E561MCL1GS 820 8×7 0.12 410 20 3300 PCG0E821MCL1GS 1500 10 × 8 0.12 750 17 4100 PCG0E152MCL1GS 2700 10 × 10 0.12 1350 12 4700 PCG0E272MCL1GS 3300 10 × 12.7 0.12 1650 10 5500 PCG0E332MCL1GS 180 5×6 0.12 144 32 1900 PCG0G181MCL1GS 390 6.3 × 6 0.12 312 22 2700 PCG0G391MCL1GS 680 8×7 0.12 544 21 3200 PCG0G681MCL1GS 1200 10 × 8 0.12 960 17 4000 PCG0G122MCL1GS 2200 10 × 10 0.12 1760 13 4600 PCG0G222MCL1GS 2700 10 × 12.7 0.12 2160 11 5300 PCG0G272MCL1GS 150 5×6 0.12 189 33 1800 PCG0J151MCL1GS 270 6.3 × 6 0.12 340 23 2600 PCG0J271MCL1GS 330 6.3 × 6 0.12 416 23 2700 PCG0J331MCL1GS 470 8×7 0.12 592 22 3100 PCG0J471MCL1GS 1000 10 × 8 0.12 1260 18 3800 PCG0J102MCL1GS 1800 10 × 10 0.12 2268 14 4400 PCG0J182MCL1GS 2200 10 × 12.7 0.12 2772 12 5000 PCG0J222MCL1GS 82 5×6 0.12 164 35 1700 PCG1A820MCL1GS 150 6.3 × 6 0.12 300 25 2500 PCG1A151MCL1GS 330 8×7 0.12 660 23 3100 PCG1A331MCL1GS 560 10 × 8 0.12 1120 20 3600 PCG1A561MCL1GS 820 10 × 10 0.12 1640 15 4300 PCG1A821MCL1GS 10 × 12.7 0.12 2000 13 4800 PCG1A102MCL1GS 1000 16 (1C) Case Size φD × L (mm) 47 5×6 0.12 150 40 1500 PCG1C470MCL1GS 82 6.3 × 6 0.12 262 30 2300 PCG1C820MCL1GS 150 8×7 0.12 480 28 2800 PCG1C151MCL1GS 270 10 × 8 0.12 864 25 3300 PCG1C271MCL1GS 470 10 × 10 0.12 1504 20 3700 PCG1C471MCL1GS 680 10 × 12.7 0.12 2176 18 4100 PCG1C681MCL1GS Design, Specifications are subject to change without notice. Printed in Japan T.2007.B.3C