CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS LE Ultra Low ESR series Ultra Low ESR, High ripple current. Load life of 2000 hours at 105°C. Radial lead type : Lead free flow soldering condition correspondence Adapted to the RoHS directive (2002/95/EC). LE Low ESR LF Specifications Item Performance Characteristics Category Temperature Range –55 ~ +105°C Rated Voltage Range 2.5 ~ 6.3V Rated Capacitance Range 470 ~ 1500µF Capacitance Tolerance ± 20% at 120Hz, 20°C tan δ Not more than value of Standard ratings at 120Hz, 20°C ESR ( 1) Not more than value of Standard ratings at 100kHz, 20°C Leakage Current ( 2) Not more than value of Standard ratings. After 2 minute's application of rated voltage. Characteristics of Temperature Z+105°C / Z+20°C 1.25 Impedance Ratio 1.25 Z - 55°C / Z + 20°C (100kHz) After 2000 hours' application of rated voltage Endurance at 105°C, capacitors meet the specified value for life characteristics listed at right. After 1000 hours' application of rated voltage Damp Heat at 60°C 90%RH, capacitors meet the specified value for life characteristics listed at right. Resistance to Soldering Heat Marking 20°C To comply with recommended conditions for reflow soldering. Pre-heating shall be done at 150 ~ 200°C and for 60 ~ 180 sec. Peak temp. is 265°C, within 10 sec. Measurement for solder temperature profile shall be made at a point on the terminal nearest where the terminals protrude through the soldering side of PC board. Capacitance change Within ± 20% of initial value ( 3) tan δ 150% or less of the initial specified value ESR ( 1) 150% or less of the initial specified value Leakage current ( 2) Initial specified value or less Capacitance change Within ± 20% of initial value ( 3) tan δ 150% or less of the initial specified value ESR ( 1) 150% or less of the initial specified value Leakage current ( 2) Initial specified value or less Capacitance change Within ± 10% of initial value ( 3) tan δ 130% or less of the initial specified value ESR ( 1) 130% or less of the initial specified value Leakage current ( 2) Initial specified value or less Navy blue print on the case top. ( 1) ESR measurements should be made at a point on the terminal nearest the end seal of the capacitor. ( 2) Conditioning : If there is doubt about the measured result, measurement should be made again after the rated voltage is applied for 120 minutes at the temperature of 105°C. ( 3) Initial value : The value before test of examination of resistance to soldering. CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS LE series Type numbering system (Example : 4V 680µF) Dimensions Capacitance Lot. No. Laminated Case 1 Silvered lead Wire 2 3 4 5 6 7 8 9 10 11 12 13 14 P ±0.5 LE 680 g 681 φ D+0.5 MAX P L E 0 G 6 8 1 MDO 1 T D Secondary code Size code Configuration φd Voltage (g:4V) Series L+0.5MAX Capacitance tolerance (± 20%) 15MIN Rated Capacitance (680µF) 4MIN Rated voltage (4V) Series name Voltage V Code 2.5 e 4 g 6.3 j Type Configuration φD × L (mm) φ8 × 9L Size φ 8 × 12L φ 10 × 13L φD 8.0 8.0 10.0 L 8.5 3.5 11.5 3.5 12.5 5.0 0.6 0.6 0.6 P φd Code 8×9 CO 8 × 12 DO 10 × 13 DO Standard ratings Rated Voltage (V) 2.5 4 6.3 Rated Capacitance (µF) Case Size φD × L (mm) tan δ Leakage Current (µA) ESR (mΩ) (20˚C / 100kHz) Rated ripple (mArms) (105˚C / 100kHz) Code 560 8×9 0.08 280 5 6000 PLE0E561MCO1 820 8×9 0.08 410 5 6300 PLE0E821MCO6 820 8 × 12 0.08 410 5 6600 PLE0E821MDO1 1000 10 × 13 0.08 500 5 7100 PLE0E102MDO1 1500 10 × 13 0.08 750 5 7300 PLE0E152MDO1 560 8×9 0.08 448 5 6000 PLE0G561MCO1 680 8 × 12 0.08 544 5 6500 PLE0G681MDO1 820 10 × 13 0.08 656 5 7000 PLE0G821MDO1 1200 10 × 13 0.08 960 5 7200 PLE0G122MDO1 470 8 × 12 0.08 592 5 6400 PLE0J471MDO1 680 10 × 13 0.08 857 5 6700 PLE0J681MDO1 820 10 × 13 0.08 1033 5 6800 PLE0J821MDO1 : In this case, 6 will be put at 12th digit of type numbering system. Design, Specifications are subject to change without notice. Printed in Japan T.2006.I.1C