CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CK Chip Type, Ultra-low ESR series Ultra-low ESR, Higher Capacitance, High ripple current. Load life of 2000 hours at 105°C. SMD type : Lead free reflow soldering condition at 260°C peak correspondence. Compliant to the RoHS directive (2011/65/EU). CJ CK Low ESR Specifications Item Performance Characteristics Category Temperature Range – 55 to +105°C Rated Voltage Range 2.5 to 6.3V Rated Capacitance Range 220 to 2200µF Capacitance Tolerance ± 20% at 120Hz, 20°C Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C ESR ( Less than or equal to the specified value at 100kHz, 20°C 1) Leakage Current ( 2) Less than or equal to the specified value . 1.25 1.25 After 2 minutes' application of rated voltage at 20°C Temperature Characteristics (Max.Impedance Ratio) Z+105°C / Z+20°C Z– 55°C / Z+20°C (100kHz) Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at 105°C. Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Damp Heat (Steady State) The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 60°C, 90% RH. Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value Less than or equal to the initial specified value After soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at right, provided that it's temperature profile is measured at the capacitor top and the terminal. Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec. The duration for over +230°C temperature at capacitor surface shall not exceed 60 seconds. In the case of peak temp, less than 250°C, reflow soldering shall be two times maximum. In the case of peak temp, less than 260°C, reflow soldering shall be once. Measurement for solder temperature profile shall be made at the capacitor top and the terminal. Navy blue print on the case top Resistance to Soldering Heat Marking 1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C. 3 Initial value : The value before test of examination of resistance to soldering. Dimensions 1 0.5 MAX. 2 3 4 5 6 7 8 9 10 11 12 13 14 PCK 0 J 2 2 1 MCO 1 GS Taping code A±0.2 C±0.2 B±0.2 φD±0.5 CK 220 j 941 Lot No. E Capacitance Type numbering system (Example : 6.3V 220µF) Positive Plastic platform 0.3 MAX. Configuration Capacitance tolerance (±20%) Series L +0.1 -0.4 Voltage ( j:6.3v) Negative Rated capacitance (220µF) Rated voltage (6.3V) H Series name Size φD L A B C E H Type (mm) φ10 × 8L φ10 × 10L 10.0 10.0 φ6.3 × 6L 6.3 φ8 × 7L 8.0 5.9 6.9 7.9 9.9 7.3 6.6 9.0 8.3 11.0 10.3 11.0 10.3 6.6 8.3 10.3 10.3 2.1 3.2 4.6 4.6 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 Dimension table in next page. Voltage V 2.5 4 6.3 Code e g j CAT.8100D CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CK series Standard Ratings Rated Voltage (V)(code) 2.5 (0E) 4 (0G) 6.3 (0J) Surge Voltage (V) 2.8 4.6 7.2 Rated Capacitance (µF) Case Size φD × L (mm) tan δ Leakage Current (µA) ESR (mΩ) (at 100kHz 20°C) Rated Ripple (mArms) Part Number 390 6.3 × 6 0.12 293 10 3900 PCK0E391MCO1GS 560 8×7 0.12 420 9 4500 PCK0E561MCO1GS 680 8×7 0.12 510 9 4500 PCK0E681MCO1GS 1200 10 × 8 0.12 900 9 5000 PCK0E122MCO1GS 2200 10 × 10 0.12 1650 8 6000 PCK0E222MCO1GS 330 6.3 × 6 0.12 396 10 3900 PCK0G331MCO1GS 470 8×7 0.12 564 9 4500 PCK0G471MCO1GS 560 8×7 0.12 672 9 4500 PCK0G561MCO1GS 1000 10 × 8 0.12 1200 9 5000 PCK0G102MCO1GS 1800 10 × 10 0.12 2160 8 6000 PCK0G182MCO1GS 220 6.3 × 6 0.12 416 10 3900 PCK0J221MCO1GS 330 8×7 0.12 624 9 4500 PCK0J331MCO1GS 390 8×7 0.12 737 9 4500 PCK0J391MCO1GS 820 10 × 8 0.12 1550 9 5000 PCK0J821MCO1GS 10 × 10 0.12 2835 8 6000 PCK0J152MCO1GS 1500 Rated ripple current (mArms) at 105°C 100kHz Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. CAT.8100D