CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CF Chip Type, Standard series Low ESR, High ripple current. Load life of 2000 hours at 105°C. SMD type : Lead free reflow soldering condition at 260°C peak correspondence. Compliant to the RoHS directive (2011/65/EU). CS CG Higher Capacitance, CF Long Life Low ESR Higher Capacitance CJ Specifications Item Performance Characteristics Category Temperature Range – 55 to +105°C Rated Voltage Range 2.5 to 25V Rated Capacitance Range 3.3 to 1500µF ± 20% Capacitance Tolerance at 120Hz, 20°C Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C ESR ( Less than or equal to the specified value at 100kHz, 20°C 1) Leakage Current ( 2) Less than or equal to the specified value. After 2 minutes' application of rated voltage at 20°C Temperature Characteristics (Max.Impedance Ratio) Z+105°C / Z+20°C Z– 55°C / Z+20°C Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at 105°C Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Damp Heat (Steady State) The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 60°C, 90% RH. Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value Less than or equal to the initial specified value 1.25 1.25 (100kHz) After soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at right, provided that it's temperature profile is measured at the capacitor top and the terminal. Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec. The duration for over +230°C temperature at capacitor surface shall not exceed 60 seconds. In the case of peak temp, less than 250°C, reflow soldering shall be two times maximum. In the case of peak temp, less than 260°C, reflow soldering shall be once. Measurement for solder temperature profile shall be made at the capacitor top and the terminal. Navy blue print on the case top Resistance to Soldering Heat Marking 1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C. 3 Initial value : The value before test of examination of resistance to soldering. Type numbering system (Example : 6.3V 150µF) Dimensions Positive Lot No. C±0.2 1 2 3 4 5 6 7 8 Taping code 9 10 11 12 13 14 φD PC F 0 J 1 5 1 MC L 1 GS 0.5 MAX. Capacitance Plastic platform 0.3 MAX. Code 4 to 6.3 （5.5L） GB 5 to 10（L GS 6） A±0.2 E B±0.2 φD±0.5 CF 150 j 841 Size code Configuration Capacitance tolerance (±20%) Rated capacitance (150µF) Series Voltage ( j:6.3v) L +0.1 - 0.4 Negative Rated voltage (6.3V) H Series name Type (mm) Size φD L A B C E H φ4 × 5.5L φ5 × 6L φ6.3 × 5.5L φ6.3 × 6L φ8 × 7L φ8 × 12L φ10 × 8L φ10 × 10L φ10 × 12.7L 6.3 10.0 4.0 5.0 6.3 8.0 8.0 10.0 10.0 5.4 12.6 5.4 5.9 5.9 6.9 11.9 7.9 9.9 7.3 11.0 5.0 6.0 7.3 9.0 9.0 11.0 11.0 6.6 10.3 4.3 5.3 6.6 8.3 8.3 10.3 10.3 6.6 10.3 4.3 5.3 6.6 8.3 8.3 10.3 10.3 2.1 4.6 1.0 1.6 2.1 3.2 3.2 4.6 4.6 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 Dimension table in next page. Voltage V 2.5 4 6.3 10 16 20 25 Code e g j A C D E CAT.8100C CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CF series Standard Ratings Rated Voltage (V)(code) 2.5 （0E） Surge Voltage (V) 2.8 Rated Capacitance (µF) Case Size φD × L (mm) tan δ 100 6.3 × 6 0.12 220 6.3 × 5.5 0.12 220 6.3 × 6 470 820 ESR (mΩ) (at 100kHz 20°C) Rated Ripple (mArms) Part Number 100 22 2600 PCF0E101MCL1GS 110 20 2800 PCF0E221MCL4GB 0.12 110 20 2800 PCF0E221MCL1GS 8×7 0.12 235 20 3300 PCF0E471MCL1GS 10 × 8 0.12 410 17 4400 PCF0E821MCL1GS 1500 10 × 10 0.12 750 13 4700 PCF0E152MCL1GS 1500 10 × 12.7 0.12 750 12 5440 PCF0E152MCL9GS 4 × 5.5 0.12 100 200 700 PCF0G330MCL1GB 100 6.3 × 5.5 0.12 100 22 2600 PCF0G101MCL4GB 100 6.3 × 6 0.12 80 22 2600 PCF0G101MCL1GS 150 6.3 × 5.5 0.12 120 22 2800 PCF0G151MCL4GB 150 5×6 0.12 300 30 2000 PCF0G151MCL6GS 150 6.3 × 6 0.12 120 22 2800 PCF0G151MCL1GS 220 8×7 0.12 176 21 3200 PCF0G221MCL1GS 330 8×7 0.12 264 21 3400 PCF0G331MCL1GS 470 10 × 8 0.12 376 17 4200 PCF0G471MCL1GS 0.12 448 13 4520 PCF0G561MCL4GS 33 4 （0G） 4.6 560 680 10 × 8 0.12 544 17 4400 PCF0G681MCL1GS 820 10 × 10 0.12 656 13 4800 PCF0G821MCL1GS 10 × 12.7 0.12 960 10 5500 PCF0G122MCL1GS 22 4 × 5.5 0.12 100 200 700 PCF0J220MCL1GB 47 5×6 0.12 148 35 1600 PCF0J470MCL1GS 82 6.3 × 5.5 0.12 103 23 2600 PCF0J820MCL4GB 82 6.3 × 6 0.12 103 23 2600 PCF0J820MCL1GS 100 6.3 × 5.5 0.12 126 23 2800 PCF0J101MCL4GB 100 5×6 0.12 315 25 2200 PCF0J101MCL6GS 100 6.3 × 6 0.12 126 23 2800 PCF0J101MCL1GS 120 6.3 × 6 0.12 151 23 3000 PCF0J121MCL1GS 150 8×7 0.12 189 22 3200 PCF0J151MCL1GS 220 8×7 0.12 277 22 3400 PCF0J221MCL1GS 330 10 × 8 0.12 416 18 4200 PCF0J331MCL1GS 0.12 592 12 5300 PCF0J471MCL4GS 1200 6.3 （0J） 7.2 470 10 （1A） 11.5 8 × 12 Leakage Current (µA) 8 × 12 470 10 × 8 0.12 592 18 4300 PCF0J471MCL6GS 470 10 × 10 0.12 592 16 4600 PCF0J471MCL1GS 680 10 × 10 0.12 857 14 5000 PCF0J681MCL1GS 680 10 × 12.7 0.12 857 10 5500 PCF0J681MCL9GS 820 10 × 12.7 0.12 1033 10 5800 PCF0J821MCL1GS 4.7 4 × 5.5 0.12 100 240 670 PCF1A4R7MCL1GB 6.8 4 × 5.5 0.12 100 240 670 PCF1A6R8MCL1GB 10 4 × 5.5 0.12 100 220 700 PCF1A100MCL1GB 15 4 × 5.5 0.12 100 200 700 PCF1A150MCL1GB 33 5×6 0.12 165 35 1500 PCF1A330MCL1GS 47 5×6 0.12 235 26 2600 PCF1A470MCL6GS 47 6.3 × 6 0.12 94 26 2600 PCF1A470MCL1GS 56 6.3 × 5.5 0.12 112 25 2500 PCF1A560MCL4GB 56 6.3 × 6 0.12 112 25 2500 PCF1A560MCL1GS 120 8×7 0.12 240 23 3000 PCF1A121MCL1GS 150 8×7 0.12 300 23 3200 PCF1A151MCL6GS 150 10 × 8 0.12 300 21 3300 PCF1A151MCL1GS 0.12 540 13 4500 PCF1A271MCL4GS 0.12 540 20 3600 PCF1A271MCL1GS 0.12 660 14 4000 PCF1A331MCL4GS 270 270 330 8 × 12 10 × 8 8 × 12 330 10 × 8 0.12 660 20 3700 PCF1A331MCL1GS 470 10 × 10 0.12 940 16 4600 PCF1A471MCL1GS 470 10 × 12.7 0.12 940 12 5300 PCF1A471MCL9GS 560 10 × 10 0.12 1120 15 4800 PCF1A561MCL1GS 560 10 × 12.7 0.12 1120 13 5230 PCF1A561MCL9GS CAT.8100C CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CF series Standard Ratings Rated Voltage (V)(code) Surge Voltage (V) Rated Capacitance (µF) 18.4 23 28.7 ESR (mΩ) (at 100kHz 20°C) Rated Ripple (mArms) Part Number 0.12 100 260 660 PCF1C3R3MCL1GB 5×6 0.12 176 45 1210 PCF1C220MCL1GS 33 6.3 × 6 0.12 106 31 2400 PCF1C330MCL1GS 39 6.3 × 5.5 0.12 125 31 2400 PCF1C390MCL4GB 39 6.3 × 6 0.12 125 31 2400 PCF1C390MCL1GS 56 8×7 0.12 179 30 2900 PCF1C560MCL1GS 82 8×7 0.12 262 28 3200 PCF1C820MCL1GS 100 10 × 8 0.12 320 27 3300 PCF1C101MCL1GS 150 10 × 8 0.12 480 25 3500 PCF1C151MCL1GS 0.12 576 16 4400 PCF1C181MCL4GS 8 × 12 180 10 × 8 0.12 576 25 3600 PCF1C181MCL1GS 220 10 × 10 0.12 704 20 3900 PCF1C221MCL1GS 220 10 × 12.7 0.12 704 14 5050 PCF1C221MCL9GS 330 10 × 12.7 0.12 1056 14 5000 PCF1C331MCL1GS 10 5×6 0.12 100 120 900 PCF1D100MCL1GS 22 6.3 × 5.5 0.12 100 50 1700 PCF1D220MCL4GB 22 6.3 × 6 0.12 88 50 1700 PCF1D220MCL1GS 39 8×7 0.12 156 45 2000 PCF1D390MCL1GS 47 8×7 0.12 188 45 2000 PCF1D470MCL1GS 56 10 × 8 0.12 224 40 2400 PCF1D560MCL1GS 68 10 × 8 0.12 272 40 2600 PCF1D680MCL1GS 82 10 × 8 0.12 328 40 2600 PCF1D820MCL1GS 100 8 × 12 0.12 400 22 3200 PCF1D101MCL1GS 120 10 × 10 0.12 480 35 2800 PCF1D121MCL1GS 150 10 × 12.7 0.12 600 20 4320 PCF1D151MCL1GS 6.3 × 6 0.12 85 80 1200 PCF1E6R8MCL1GS 10 8×7 0.12 125 60 1600 PCF1E100MCL1GS 22 10 × 8 0.12 275 50 2200 PCF1E220MCL1GS 6.8 25 （1E） Leakage Current (µA) 4 × 5.5 180 20 （1D） tan δ 22 3.3 16 （1C） Case Size φD × L (mm) 33 8 × 12 0.12 413 30 2800 PCF1E330MCL1GS 47 8 × 12 0.12 588 30 3000 PCF1E470MCL4GS 47 10 × 10 0.12 588 45 2400 PCF1E470MCL1GS 56 10 × 12.7 0.12 700 28 3800 PCF1E560MCL1GS Rated ripple current (mArms) at 105°C 100kHz Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. No marked, 1 will be put at 12th digit of type numbering system. : In this case, 4 will be put at 12th digit of type numbering system. : In this case, 6 will be put at 12th digit of type numbering system. : In this case, 9 will be put at 12th digit of type numbering system. CAT.8100C