ALUMINUM ELECTROLYTIC CAPACITORS UN Chip Type, Bi-Polarized, Higher Capacitance Range series Chip Type ,higher capacitance in larger case sizes (φ12.5, φ16, φ18, φ20) Designed for surface mounting on high density PC board. Bi-polarized series for operations over wide temperature range of – 55 ~ +105°C. Applicable to automatic mounting machine using carrier tape and tray. Adapted to the RoHS directive (2002/95/EC). UN UJ Bi-polarized Specifications Item Performance Characteristics Category Temperature Range – 55 ~ +105°C Rated Voltage Range 6.3 ~ 100V Rated Capacitance Range 22 ~ 3300µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 1 minutes' application of rated voltage, leakage current is not more than 0.03CV or 4 (µA), whichever is greater. Rated voltage (V) 6.3 10 16 25 35 50 63 100 tan δ (MAX) 0.26 0.22 0.18 0.16 0.14 0.12 0.10 0.09 tan δ 120Hz 20°C For capacitance of more than 1000µF, add 0.02 for every increase of 1000µF. Rated voltage (V) Stability at Low Temperature Impedance ratio Z–25°C / Z+20°C ZT / Z20 (MAX.) Z–40°C / Z+20°C 6.3 10 16 25 35 50 63 100 5 4 3 2 2 2 2 2 10 8 6 4 3 3 3 120Hz 3 Endurance After 2000 hours' application of rated voltage at 105°C with the polarity inverted every 250 hours, capacitors meet the characteristic requirements listed at right. Shelf Life After storing the capacitors under no load at 105°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above. Marking Black print on the case top. Type numbering system (Example : 50V 330µF) Chip Type A±0.2 B±0.2 Voltage Trade mark Within ±20% of initial value 200% or less of initial specified value Initial specified value or less Capacitance change tan δ Leakage current Plastic platform Lot No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 C±0.2 E B±0.2 f D±0.5 50V H0536 330 µF UN Package code BP nichicon UUN 1 H 3 3 1 M N L 1 MS Taping MS Tray ZD Size code Capacitance Pressure relief vent L±0.5 V (µF) Code Cap. fD 12.5 16. 18. 20. A 4.0 4.5 5.0 5.0 Capacitance Tolerance(±20%) H±0.1 (mm) Dimensions Configuration A±0.2 Series Rated Capacitance(330µF) Rated voltage(50V) φD Code 12.5 ~ 18 NL 20 RL The lead terminal structure : The same bent Series name lead type (refer to p.60) that is currently B 13.6 17.1 19.1 21.1 C 16.0 19.5 21.5 23.5 also available upon request. E 8.0 10.5 11.5 13.5 In this case of the bent lead type, Q H 2.5 3.75 3.75 3.75 used on 10mm diameter and smaller parts, is Type will be put at the 11th digit of type numbering system. Please ask for details. 6.3 10 16 25 35 50 63 0J 1A 1C 1E 1V 1H 1J 100 2A 22 220 12.5 × 13.5 100 33 330 12.5 × 16 150 47 470 100 101 220 221 330 331 470 471 12.5 × 13.5 270 12.5 × 13.5 1000 102 12.5 × 16 500 2200 222 3300 332 740 740 920 18 × 16.5 16 × 21.5 18 × 21.5 270 16 × 16.5 330 18 × 16.5 16 × 21.5 18 × 21.5 450 450 590 12.5 × 13.5 310 16 × 16.5 370 340 16 × 16.5 420 16 × 16.5 490 16 × 16.5 600 18 × 16.5 16 × 21.5 670 670 18 × 21.5 780 18 × 21.5 830 00 ~ 470 100 ~ 470 1000 ~ 3300 50 Hz 0.75 0.80 0.85 120 Hz 1.00 1.00 1.00 300 Hz 1.35 1.23 1.10 1 kHz 1.57 1.34 1.13 130 12.5 × 13.5 140 16 × 16.5 180 12.5 × 16 230 16 × 16.5 270 18 × 21.5 310 18 × 16.5 16 × 21.5 18 × 21.5 400 400 540 18 × 21.5 440 20 × 21.5 590 20 × 21.5 640 Case size φ D × L (mm) Rated Ripple Rated Ripple (mArms) at 105°C 120Hz Frequency coefficient of rated ripple current Frequency 180 12.5 × 13.5 In this case, 6 will be put at 12th digit of type numbering system, " " Cap.(µF) 12.5 × 13.5 12.5 × 13.5 10 kHz~ 2.00 1.50 1.15 Taping specifications are given in page 24. Recommended land size, soldering by reflow are given in page 25, 26. Please refer to page 3 for the minimum order quantity. CAT.8100V