Ordering number : ENN7330 SPM5001 RF Mixer MMIC SPM5001 RF Double Balanced Mixer Features • [SPM5001] 0.3 4 0.25 2.1 • unit : mm 2211 5 6 3 2 0.65 1 0.15 0.07 • Wide band double balanced mixer. Low distortion. The chip surface is covered with highly reliable protection film. Automatic surface mounting is available. MCPH6 package. 0.25 • Package Dimensions 1.6 • 2.0 6 5 4 1 2 3 1 : Gate1 2 : Drain1 3 : Drain2 4 : Source2 5 : Source1 6 : Gate2 0.85 (Bottom view) Specifications SANYO : MCPH6 (Top view) Absolute Maximum Ratings at Ta=25°C Parameter Symbol Conditions Ratings Unit Drain-to-Source Voltage VDS 6 Gate-to-Source Voltage VGS --4 V V Drain Current ID 60 mA Allowable Power Dissipation PD 200 mW Junction Temperature Tj 150 °C Storage Temperature Tstg --55 to +150 °C Electrical Characteristics at Ta=25°C Parameter Symbol Gate-to-Source Leakage Current Zero-Gate Voltage Drain Current Conditions Ratings min typ max Unit µA IG1S1O VG1S1=--5V --10 IG2S1O VG2S1=--5V --10 µA IG2S2O VG2S2=--5V --10 µA IG1S2O VG1S2=--5V ID1S1S VD1=3V, VG1S1=0, VG2=--4V VD2=3V, VG2S1=0, VG1=--4V 20 20 40 60 mA VD1=3V, VG2S2=0, VG1=--4V VD2=3V, VG1S2=0, VG2=--4V 20 40 60 mA 20 40 60 mA ID2S1S ID1S2S ID2S2S 40 --10 µA 60 mA Continued on next page. Any and all SANYO products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO representative nearest you before using any SANYO products described or contained herein in such applications. SANYO assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO products described or contained herein. SANYO Electric Co.,Ltd. Semiconductor Company TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN 32603 TS IM TA-100360 No.7330-1/3 SPM5001 Continued from preceding page. Parameter Symbol VG1S1(off) Gate-to-Source Cutoff Voltage Ratings Conditions min typ Unit max VD1=3V, ID=100µA VD2=3V, ID=100µA --0.5 --1.0 --1.5 V VG2S1(off) --0.5 --1.0 --1.5 V VG2S2(off) VD1=3V, ID=100µA --0.5 --1.0 --1.5 V VG1S2(off) VD2=3V, ID=100µA --0.5 --1.0 --1.5 V Equivalent Circuit [Reference Data] Mixer Characteristics Measured by the Evaluation Board for SPM5001 Drain1 Drain2 Gate1 Source2 Source1 Gate2 Chip capacitor Balun transformer --40 --60 --80 --100 --100 --80 --60 --40 --20 0 20 --20 Bm dBm --3 = LO 0d --40 = LO --60 --80 --120 --100 40 --80 --60 --40 --20 Total Current vs. RF Power 40 IT04676 VD=3V, ID=4mA(LO off) f(RF)=488MHz f(LO)=443.15MHz f(IF)=44.85MHz Power(RF)= --20dBm 9 11 8 9 20 Conversion Loss* 10 VD=3V, ID=6mA(LO off) f(RF)=1960MHz f(LO)=1750MHz 10 0 RF Power@1 Tone -- dBm IT04675 LC -- dB Total Current -- mA 12 0 3rd Order Intermodulation Distortion VD=3V, ID=6mA(LO off) IIP3(LO=0dBm)=21.2dBm f(RF1)=1960MHz IIP3(LO= --3dBm)=21.0dBm f(RF2)=1961MHz f(LO)=1750MHz --100 RF Power@1 Tone -- dBm 13 20 LO LO= =0dBm --3d Bm --20 LO= -LO= 3dBm 0dB m Output Power -- dBm 0 3rd Order Intermodulation Distortion VD=3V, ID=6mA(LO off) IIP3(LO=0dBm)=16.7dBm f(RF1)=880MHz IIP3(LO= --3dBm)=13.6dBm f(RF2)=881MHz f(LO)=965MHz m m dB dB =0 --3 LO O= L Output Power -- dBm 20 7 6 Lo=0dBm 8 5 Lo= --3dBm 7 --100 --80 --60 --40 --20 RF Power -- dBm 0 20 IT04677 4 --15 --10 --5 0 5 10 15 IT05339 LO Power -- dBm * This Conversion Loss characteristic includes the loss of the test board and the Balun Transformer. No.7330-2/3 SPM5001 Measurement System • IF output power vs. RF input power RF Signal Generator IF Bias Tee Spectrum Analyzer Bias Tee Vd Signal Generator LO Bias Tee Vg • IM3, IM2 vs. RF input power Signal Generator1 RF IF Bias Tee Bias Tee Spectrum Analyzer Signal Generator2 Vd Signal Generator LO Bias Tee Vg Specifications of any and all SANYO products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO products(including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be expor ted without obtaining the expor t license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Electric Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of March, 2003. Specifications and information herein are subject to change without notice. PS No.7330-3/3