LM124-LM224-LM324 Low Power Quad Operational Amplifiers ■ Wide gain bandwidth: 1.3MHz ■ Input common-mode voltage range includes ground ■ Large voltage gain: 100dB ■ Very low supply current/ampli: 375µA ■ Low input bias current: 20nA ■ Low input offset voltage: 5mV max. (for more accurate applications, use the equivalent parts LM124A-LM224A-LM324A which feature 3mV max.) ■ Low input offset current: 2nA ■ Wide power supply range: Single supply: +3V to +30V Dual supplies: ±1.5V to ±15V N DIP14 (Plastic Package) D SO-14 (Plastic Micropackage) Description These circuits consist of four independent, high gain, internally frequency compensated operational amplifiers. They operate from a single power supply over a wide range of voltages. Operation from split power supplies is also possible and the low power supply current drain is independent of the magnitude of the power supply voltage. P TSSOP-14 (Thin Shrink Small Outline Package) Order Codes Part Number LM124N LM124D/DT LM224N LM224D/DT Temperature Range -55°C, +125°C -40°C, +105°C LM224PT LM324N LM324D/DT LM324PT June 2005 0°C, +70°C Package Packaging DIP SO DIP SO TSSOP (Thin Shrink Outline Package) DIP SO TSSOP (Thin Shrink Outline Package) Tube Tube or Tape & Reel Tube Tube or Tape & Reel Tape & Reel Tube Tube or Tape & Reel Tape & Reel Rev 3 1/16 www.st.com 16 Absolute Maximum Ratings 1 LM124-LM224-LM324 Absolute Maximum Ratings Table 1. 15Key parameters and their absolute maximum ratings Symbol VCC Parameter LM124 Supply voltage LM224 LM324 Unit ±16 or 32 V Vi Input Voltage -0.3 to Vcc + 0.3 V Vid Differential Input Voltage (1) -0.3 to Vcc + 0.3 V Ptot Power Dissipation N Suffix D Suffix 500 500 400 Output Short-circuit Duration (2) Iin Input Current (3) Toper Operating Free-air Temperature Range Tstg Storage Temperature Range Rthja ESD 500 400 mW 50 mA Infinite 50 50 -55 to +125 -40 to +105 0 to +70 °C -65 to +150 °C Thermal Resistance Junction to Ambient SO14 TSSOP14 DIP14 103 100 66 °C/W HBM: Human Body Model(4) 250 MM: Machine Model(5) 150 CDM: Charged Device Model V 1500 + 1. Either or both input voltages must not exceed the magnitude of VCC or VCC-. 2. Short-circuits from the output to VCC can cause excessive heating if VCC > 15V. The maximum output current is approximately 40mA independent of the magnitude of VCC. Destructive dissipation can result from simultaneous short-circuit on all amplifiers. 3. This input current only exists when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of the input PNP transistor becoming forward biased and thereby acting as input diodes clamps. In addition to this diode action, there is also NPN parasitic action on the IC chip. this transistor action can cause the output voltages of the op-amps to go to the VCC voltage level (or to ground for a large overdrive) for the time duration than an input is driven negative. This is not destructive and normal output will set up again for input voltage higher than -0.3V. 4. Human body model, 100pF discharged through a 1.5kΩ resistor into pin of device. 5. Machine model ESD, a 200pF cap is charged to the specified voltage, then discharged directly into the IC with no external series resistor (internal resistor < 5Ω), into pin to pin of device. 2/16 LM124-LM224-LM324 2 Pin & Schematic Diagram Pin & Schematic Diagram Figure 1. Pin connections (top view) 14 Output 4 Output 1 1 Inverting Input 1 2 - - 13 Inverting Input 4 Non-inverting Input 1 3 + + 12 Non-inverting Input 4 11 VCC - VCC + 4 Non-inverting Input 2 5 + + 10 Non-inverting Input 3 Inverting Input 2 6 - - 9 Inverting Input 3 Output 2 7 Figure 2. 8 Output 3 Schematic diagram (1/4 LM124) 3/16 Electrical Characteristics 3 LM124-LM224-LM324 Electrical Characteristics Table 2. VCC+ = +5V, VCC-= Ground, Vo = 1.4V, Tamb = +25°C (unless otherwise specified) Symbol Vio Parameter Input Offset Voltage - note Tamb = +25°C Min. Typ. Max. 2 5 7 7 9 Unit (1) Tmin ≤ T amb ≤ T max LM324 LM324 mV Iio Input Offset Current Tamb = +25°C Tmin ≤ T amb ≤ T max 2 30 100 nA Iib Input Bias Current - note (2) Tamb = +25°C Tmin ≤ T amb ≤ T max 20 150 300 nA Avd Large Signal Voltage Gain VCC+ = +15V, RL = 2kΩ, Vo = 1.4V to 11.4V Tamb = +25°C Tmin ≤ T amb ≤ T max 50 25 100 65 65 110 V/mV Supply Voltage Rejection Ratio (Rs ≤ 10kΩ) SVR 4/16 VCC+ = 5V to 30V Tamb = +25°C Tmin ≤ T amb ≤ T max ICC Supply Current, all Amp, no load Tamb = +25°C V CC = +5V VCC = +30V Tmin ≤ T amb ≤ T max V CC = +5V V CC = +30V Vicm Input Common Mode Voltage Range VCC = +30V - note (3) Tamb = +25°C Tmin ≤ T amb ≤ T max 0 0 CMR Common Mode Rejection Ratio (Rs ≤ 10kΩ) Tamb = +25°C Tmin ≤ Tamb ≤ Tmax 70 60 80 Isource Output Current Source (V id = +1V) VCC = +15V, Vo = +2V 20 40 Isink Output Sink Current (Vid = -1V) VCC = +15V, Vo = +2V VCC = +15V, Vo = +0.2V 10 12 20 50 VOH High Level Output Voltage VCC = +30V Tamb = +25°C Tmin ≤ T amb ≤ T max Tamb = +25°C Tmin ≤ T amb ≤ T max VCC = +5V, R L = 2kΩ Tamb = +25°C Tmin ≤ T amb ≤ T max 0.7 1.5 0.8 1.5 dB 1.2 3 1.2 3 VCC -1.5 VCC -2 mA V dB 70 mA mA µA V RL = 2kΩ R L = 10kΩ 26 26 27 27 3.5 3 27 28 LM124-LM224-LM324 Table 2. Electrical Characteristics VCC+ = +5V, VCC-= Ground, Vo = 1.4V, Tamb = +25°C (unless otherwise specified) Symbol VOL SR GBP THD Parameter Low Level Output Voltage (RL = 10kΩ) Tamb = +25°C Tmin ≤ T amb ≤ T max Slew Rate VCC = 15V, V i = 0.5 to 3V, RL = 2kΩ, CL = 100pF, unity Gain Gain Bandwidth Product VCC = 30V, f =100kHz,V in = 10mV, R L = 2kΩ, CL = 100pF Total Harmonic Distortion f = 1kHz, Av = 20dB, RL = 2kΩ, Vo = 2V pp, CL = 100pF, VCC = 30V Min. Typ. Max. Unit 5 20 20 mV V/µs 0.4 MHz 1.3 % 0.015 Equivalent Input Noise Voltage f = 1kHz, Rs = 100Ω, VCC = 30V 40 DVio Input Offset Voltage Drift 7 30 DIIio Input Offset Current Drift 10 200 Channel Separation - note (4) 1kHz ≤ f ≤ 20kHZ 120 en Vo1/Vo2 nV -----------Hz µV/ °C pA/ °C dB 1. Vo = 1.4V, Rs = 0Ω, 5V < VCC + < 30V, 0 < Vic < VCC+ - 1.5V 2. The direction of the input current is out of the IC. This current is essentially constant, independent of the state of the output so no loading change exists on the input lines. 3. The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end of the common-mode voltage range is VCC+ - 1.5V, but either or both inputs can go to +32V without damage. 4. Due to the proximity of external components insure that coupling is not originating via stray capacitance between these external parts. This typically can be detected as this type of capacitance increases at higher frequencies. Table 3. Vcc+ = +15V, Vcc- = 0V, Tamb = 25°C (unless otherwise specified) Symbol Conditions Vio Avd RL = 2kΩ Icc No load, per amplifier Vicm VOH RL = 2kΩ (VCC VOL RL = 10kΩ +=15V) Value Unit 0 mV 100 V/mV 350 µA -15 to +13.5 V +13.5 V 5 mV Ios Vo = +2V, VCC = +15V +40 mA GBP RL = 2kΩ, CL = 100pF 1.3 MHz SR RL = 2kΩ, CL = 100pF 0.4 V/µs 5/16 Electrical Characteristics Figure 3. Input bias current vs. ambient temperature LM124-LM224-LM324 Figure 4. Current limiting INPUT BIAS CURRENT versus AMBIENT TEMPERATURE IB (nA) 24 21 18 15 12 9 6 3 0 -55-35-15 5 25 45 65 85 105 125 AMBIENT TEMPERATURE (°C) Figure 5. Input voltage range Figure 6. Supply current Figure 7. Gain bandwidth product Figure 8. Common mode rejection ratio 6/16 LM124-LM224-LM324 Figure 9. Electrical Characteristics Electrical curves 7/16 Electrical Characteristics LM124-LM224-LM324 Figure 10. Input current Figure 11. Large signal voltage gain Figure 12. Power supply & common mode rejection ratio Figure 13. Voltage gain 8/16 LM124-LM224-LM324 4 Typical Single - Supply Applications Typical Single - Supply Applications Figure 14. AC coupled inverting amplifier Figure 15. High input Z adjustable gaind DC instrumentation amplifier if R1 = R5 and R3 = R4 = R6 = R7 2R e0 = 1 + ----------1- (e2 -e1) R 2 As shown e0 = 101 (e2 - e1). Figure 16. AC coupled non inverting amplifier Figure 17. DC summing amplifier e0 = e1 +e2 -e3 -e4 Where (e1 +e2) ≥ (e3 +e4) to keep e0 ≥ 0V Figure 18. Non-inverting DC gain Figure 19. Low drift peak detector 9/16 Typical Single - Supply Applications Figure 20. Activer bandpass filter LM124-LM224-LM324 Figure 21. High input Z, DC differential amplifier R R 1 = ------4For ------R R 2 3 (CMRR depends on this resistor ratio match) Fo = 1kHz Q = 50 Av = 100 (40dB) Figure 22. Using symmetrical amplifiers to reduce input current (general concept) 10/16 e0 ⎛ 1 + R-------4⎞ ⎝ R 3⎠ (e2 - e1) As shown e0 = (e2 - e1) LM124-LM224-LM324 5 Macromodels Note: Note: Please consider following remarks before using this macromodel: Macromodels All models are a trade-off between accuracy and complexity (i.e. simulation time). Macromodels are not a substitute to breadboarding; rather, they confirm the validity of a design approach and help to select surrounding component values. A macromodel emulates the NOMINAL performance of a TYPICAL device within SPECIFIED OPERATING CONDITIONS (i.e. temperature, supply voltage, etc.). Thus the macromodel is often not as exhaustive as the datasheet, its goal is to illustrate the main parameters of the product. Data issued from macromodels used outside of its specified conditions (Vcc, Temperature, etc.) or even worse: outside of the device operating conditions (Vcc, Vicm, etc.) are not reliable in any way. ** Standard Linear Ics Macromodels, 1993. ** CONNECTIONS : * 1 INVERTING INPUT * 2 NON-INVERTING INPUT * 3 OUTPUT * 4 POSITIVE POWER SUPPLY * 5 NEGATIVE POWER SUPPLY .SUBCKT LM124 1 3 2 4 5 (analog) ******************************************************* .MODEL MDTH D IS=1E-8 KF=3.104131E-15 CJO=10F * INPUT STAGE CIP 2 5 1.000000E-12 CIN 1 5 1.000000E-12 EIP 10 5 2 5 1 EIN 16 5 1 5 1 RIP 10 11 2.600000E+01 RIN 15 16 2.600000E+01 RIS 11 15 2.003862E+02 DIP 11 12 MDTH 400E-12 DIN 15 14 MDTH 400E-12 VOFP 12 13 DC 0 VOFN 13 14 DC 0 IPOL 13 5 1.000000E-05 CPS 11 15 3.783376E-09 DINN 17 13 MDTH 400E-12 VIN 17 5 0.000000e+00 DINR 15 18 MDTH 400E-12 VIP 4 18 2.000000E+00 FCP 4 5 VOFP 3.400000E+01 FCN 5 4 VOFN 3.400000E+01 FIBP 2 5 VOFN 2.000000E-03 FIBN 5 1 VOFP 2.000000E-03 * AMPLIFYING STAGE FIP 5 19 VOFP 3.600000E+02 11/16 Macromodels FIN 5 19 VOFN 3.600000E+02 RG1 19 5 3.652997E+06 RG2 19 4 3.652997E+06 CC 19 5 6.000000E-09 DOPM 19 22 MDTH 400E-12 DONM 21 19 MDTH 400E-12 HOPM 22 28 VOUT 7.500000E+03 VIPM 28 4 1.500000E+02 HONM 21 27 VOUT 7.500000E+03 VINM 5 27 1.500000E+02 EOUT 26 23 19 5 1 VOUT 23 5 0 ROUT 26 3 20 COUT 3 5 1.000000E-12 DOP 19 25 MDTH 400E-12 VOP 4 25 2.242230E+00 DON 24 19 MDTH 400E-12 VON 24 5 7.922301E-01 .ENDS 12/16 LM124-LM224-LM324 LM124-LM224-LM324 6 Package Mechanical Data Package Mechanical Data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a Lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com. 6.1 DIP14 Package Plastic DIP-14 MECHANICAL DATA mm. inch DIM. MIN. a1 0.51 B 1.39 TYP MAX. MIN. TYP. MAX. 0.020 1.65 0.055 0.065 b 0.5 0.020 b1 0.25 0.010 D 20 0.787 E 8.5 0.335 e 2.54 0.100 e3 15.24 0.600 F 7.1 0.280 I 5.1 0.201 L Z 3.3 1.27 0.130 2.54 0.050 0.100 P001A 13/16 Package Mechanical Data 6.2 LM124-LM224-LM324 SO-14 Package SO-14 MECHANICAL DATA DIM. mm. MIN. TYP A a1 inch MAX. MIN. TYP. 1.75 0.1 0.068 0.2 a2 MAX. 0.003 0.007 1.65 0.064 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.019 c1 45˚ (typ.) D 8.55 8.75 0.336 E 5.8 6.2 0.228 e 1.27 e3 3.8 G L M S 0.244 0.050 7.62 F 0.344 0.300 4.0 0.149 4.6 5.3 0.181 0.208 0.5 1.27 0.019 0.050 0.68 0.157 0.026 8 ˚ (max.) PO13G 14/16 LM124-LM224-LM324 6.3 Package Mechanical Data TSSOP14 Package TSSOP14 MECHANICAL DATA mm. inch DIM. MIN. TYP A MAX. MIN. TYP. MAX. 1.2 A1 0.05 A2 0.8 b 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 D 4.9 5 5.1 0.193 0.197 0.201 E 6.2 6.4 6.6 0.244 0.252 0.260 E1 4.3 4.4 4.48 0.169 0.173 0.176 1 e 0.65 BSC K 0˚ L 0.45 A 0.60 0.0256 BSC 8˚ 0˚ 0.75 0.018 8˚ 0.024 0.030 A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 0080337D 15/16 Revision History 7 LM124-LM224-LM324 Revision History Date Revision Changes Oct. 2003 1 First Release Jan. 2005 2 Modifications on AMR Table 1 on page 2 (explanation of Vid and Vi limits) June 2005 3 ESD protection inserted in Table 1 on page 2 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners © 2005 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 16/16