STMICROELECTRONICS LM258WDT

LM158W-LM258W-LM358W
Low power dual operational amplifiers
Features
■
Internally frequency compensated
■
Large DC voltage gain: 100 dB
■
Wide bandwidth (unity gain): 1.1 MHz
(temperature compensated)
■
Very low supply current per operator
essentially independent of supply voltage
■
Low input bias current: 20 nA
(temperature compensated)
■
Low input offset voltage: 2 mV
■
Low input offset current: 2 nA
■
Input common-mode voltage range includes
ground
■
Differential input voltage range equal to the
power supply voltage
■
Large output voltage swing 0 V to (VCC - 1.5 V)
■
ESD internal protection: 2 kV
N
DIP-8
(Plastic package)
D&S
SO-8 & miniSO-8
(Plastic micropackage)
P
TSSOP8
(Thin shrink small outline package)
Pin connections
(top view)
Description
1
These circuits consist of two independent, highgain, internally frequency-compensated which
were designed specifically to operate from a
single power supply over a wide range of
voltages. The low power supply drain is
independent of the magnitude of the power supply
voltage.
April 2007
2
-
3
+
4
Application areas include transducer amplifiers,
DC gain blocks and all the conventional op-amp
circuits which now can be more easily
implemented in single power supply systems. For
example, these circuits can be directly supplied
with the standard +5 V which is used in logic
systems and will easily provide the required
interface electronics without requiring any
additional power supply.
In the linear mode the input common-mode
voltage range includes ground and the output
8
7
-
6
+
5
1 - Output 1
2 - Inverting input
3 - Non-inverting input
4 - VCC5 - Non-inverting input 2
6 - Inverting input 2
7 - Output 2
8 - VCC+
voltage can also swing to ground, even though
operated from only a single power supply voltage.
Rev 6
1/20
www.st.com
20
Contents
LM158W-LM258W-LM358W
Contents
1
Schematic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2
Absolute maximum ratings and operating conditions . . . . . . . . . . . . . 4
3
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4
Typical applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.1
DIP8 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.2
SO-8 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.3
MiniSO-8 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.4
TSSOP8 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6
Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
7
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2/20
LM158W-LM258W-LM358W
1
Schematic diagram
Schematic diagram
Figure 1.
Schematic diagram (1/2 LM158W)
3/20
Absolute maximum ratings and operating conditions
2
LM158W-LM258W-LM358W
Absolute maximum ratings and operating conditions
Table 1.
Absolute maximum ratings
Symbol
VCC
Parameter
LM158W/AW LM258W/AW LM358W/AW
Unit
+32
V
Supply voltage
Vi
Input voltage
-0.3 to VCC +0.3
V
Vid
Differential input voltage
-0.3 to VCC +0.3
V
Ptot
Power dissipation (1)
500
mW
Output short-circuit duration
Iin
Input current
(2)
Infinite
(3)
50
Toper
Operating free-air temperature range
Tstg
Storage temperature range
-55 to +125
-40 to +105
mA
0 to +70
°C
-65 to +150
°C
Thermal resistance junction to
ambient(4) (5)
Rthja
SO-8
125
MiniSO-8
190
TSSOP8
120
DIP-8
85
°C/W
Thermal resistance junction to case
Rthjc
SO-8
40
MiniSO-8
39
TSSOP8
37
DIP-8
HBM: human body
ESD
°C/W
41
model(6)
2
kV
MM: machine model
200
V
CDM: charged device model(8)
1.5
kV
(7)
1. Power dissipation must be considered to ensure maximum junction temperature (Tj) is not exceeded.
2. Short-circuits from the output to VCC can cause excessive heating if VCC > 15V. The maximum output
current is approximately 40 mA independent of the magnitude of VCC. Destructive dissipation can result
from simultaneous short-circuits on all amplifiers.
3. This input current only exists when the voltage at any of the input leads is driven negative. It is due to the
collector-base junction of the input PNP transistor becoming forward biased and thereby acting as input
diode clamps. In addition to this diode action, there is also NPN parasitic action on the IC chip. This
transistor action can cause the output voltages of the Op-amps to go to the VCC voltage level (or to ground
for a large overdrive) for the time during which an input is driven negative. This is not destructive and
normal output will be restored for input voltage higher than -0.3 V.
4. Short-circuits can cause excessive heating and destructive dissipation.
5. Rth are typical values.
6. Human body model: 100 pF discharged through a 1.5 kΩ resistor between two pins of the device, done for
all couples of pin combinations with other pins floating.
7. Machine model: a 200 pF cap is charged to the specified voltage, then discharged directly between two
pins of the device with no external series resistor (internal resistor < 5 Ω), done for all couples of pin
combinations with other pins floating.
8. Charged device model: all pins plus package are charged together to the specified voltage and then
discharged directly to the ground.
4/20
LM158W-LM258W-LM358W
Table 2.
Absolute maximum ratings and operating conditions
Operating conditions
Symbol
Parameter
VCC
Supply voltage
Vicm
Common mode input voltage range
Tamb = +25° C
Toper
Operating free air temperature range
LM158W
LM258W
LM358W
LM258WY-LM358WY
Value
Unit
3 to 32
V
VDD -0.3 to VCC -1.5
-55 - +125
-40 - +105
0 - +70
-40 - +125
V
°C
5/20
Electrical characteristics
LM158W-LM258W-LM358W
3
Electrical characteristics
Table 3.
VCC+ = +5 V, VCC-= Ground, Vo = 1.4 V, Tamb = +25°C (unless otherwise specified)
Symbol
Parameter
LM158AW-LM258AW
LM358AW
Min. Typ.
Vio
Input offset voltage (1)
Tamb = +25° C - except LM158AW/358W
Tamb = +25° C - LM158AW/358W
1
1
Tmin ≤ Tamb ≤ Tmax - except LM358W
Tmin ≤ Tamb ≤ Tmax - LM358W
Max.
LM158W-LM258W
LM358W
Min. Typ.
3
2
2
2
4
Unit
Max.
5
7
7
9
mV
mV
Iio
Input offset current
Tamb = +25° C
Tmin ≤ Tamb ≤ Tmax
2
10
30
2
30
40
nA
Iib
Input bias current (2)
Tamb = +25 °C
Tmin ≤ Tamb ≤ Tmax
20
50
100
20
150
200
nA
Avd
Large signal voltage gain:
VCC = +15 V, RL = 2 kΩ, Vo = 1.4 V to 11.4 V
Tamb = +25 °C
Tmin ≤ Tamb ≤ Tmax
50
25
100
50
25
100
SVR
Supply voltage rejection ratio (Rs ≤10 kΩ)
VCC+ = 5 V to 30 V
Tamb = +25° C
Tmin ≤ Tamb ≤ Tmax
65
65
100
65
65
100
ICC
Supply current, all amp, no load
Tmin ≤ Tamb ≤ Tmax, VCC = +5 V
Tmin ≤ Tamb ≤ Tmax, VCC = +30 V
Vicm
Input common mode voltage range
VCC = +30 V (3)
Tamb = +25° C
Tmin ≤ Tamb ≤ Tmax
0
0
CMR
Common mode rejection ratio (Rs ≤10kΩ)
Tamb = +25° C
Tmin ≤ Tamb ≤ Tmax
70
60
85
Isource
Output current source
VCC = +15 V, Vo = +2 V, Vid = +1 V
20
40
Output sink current (Vid = -1 V)
VCC = +15V, Vo = +2V
VCC = +15V, Vo = +0.2V
10
12
20
50
Isink
6/20
0.7
1.2
2
VCC+ -1.5
VCC+ -2
60
0.7
0
0
70
60
85
20
40
10
12
20
50
V/mV
dB
1.2
2
mA
VCC+ -1.5
VCC+ -2
V
dB
60
mA
mA
µA
LM158W-LM258W-LM358W
Table 3.
Symbol
Electrical characteristics
VCC+ = +5 V, VCC-= Ground, Vo = 1.4 V, Tamb = +25°C (unless otherwise specified)
Parameter
LM158AW-LM258AW
LM358AW
Min. Typ.
VOPP
Output voltage swing (RL = 2kΩ)
Tamb = +25° C
Tmin ≤ Tamb ≤ Tmax
0
0
VOH
High level output voltage (VCC+ = 30 V)
Tamb = +25°C, RL = 2 kΩ
Tmin ≤ Tamb ≤ Tmax
Tamb = +25° C, RL = 10 kΩ
Tmin ≤ Tamb ≤ Tmax
26
26
27
27
Max.
VCC+ -1.5
VCC+ -2
27
LM158W-LM258W
LM358W
Min. Typ.
28
V
28
Low level output voltage (RL = 10 kΩ)
Tamb = +25° C
Tmin ≤ Tamb ≤ Tmax
SR
Slew rate
VCC = 15 V, Vi = 0.5 to 3 V, RL = 2 kΩ,
CL = 100 pF, unity Gain
0.3
0.6
0.3
0.6
Gain bandwidth product
VCC = 30 V, f =100 kHz, Vin =10 mV, RL=2 kΩ,
CL = 100 pF
0.7
1.1
0.7
1.1
GBP
THD
Total harmonic distortion
f = 1 kHz, Av = 20 dB, RL = 2 kΩ, Vo = 2 Vpp,
CL = 100 pF, VO = 2 Vpp
20
20
V
27
VOL
5
Max.
VCC+ -1.5
VCC+ -2
0
0
26
26
27
27
Unit
5
20
20
mV
V/µs
MHz
%
0.02
0.02
Equivalent input noise voltage
f = 1 kHz, Rs = 100 Ω, VCC = 30 V
55
55
DVio
Input offset voltage drift
7
15
7
30
µV/°C
DIio
Input offset current drift
10
200
10
300
pA/°C
en
Vo1/Vo2
Channel separation
1 kHz ≤ f ≤ 20 kHz
nV
-----------Hz
(4)
120
120
dB
1. Vo = 1.4 V, Rs = 0 Ω, 5 V < VCC+ < 30 V, 0 < Vic < VCC+ - 1.5 V
2. The direction of the input current is out of the IC. This current is essentially constant, independent of the state of the output
so there is no load change on the input lines.
3. The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3 V.
The upper end of the common-mode voltage range is VCC+ - 1.5 V, but either or both inputs can go to +32 V without
damage.
4. Due to the proximity of external components ensure that there is no coupling originating via stray capacitance between
these external parts. Typically, this can be detected at higher frequencies because then this type of capacitance increases.
7/20
Electrical characteristics
Figure 2.
LM158W-LM258W-LM358W
Open loop frequency response
OPEN LOOP FREQUENCY RESPONSE (NOTE 3)
140
Large signal frequency response
LARGE SIGNAL FREQUENCY RESPONSE
20
0.1mF
100
VCC
-
VI
VCC/2
80
VO
+
VCC = 30V &
-55°C Tamb
60
100k W
10M W
OUTPUT SWING (Vpp)
120
VOLTAGE GAIN (dB)
Figure 3.
+125°C
40
20
VCC = +10 to + 15V &
-55°C Tamb +125°C
0
1k W
15
+7V
10
100
1k
10k
100k
1M
5
10M
1k
10k
Voltage follower pulse response
Figure 5.
OUTPUT VOLTAGE (mV)
OUTPUT
VOLTAGE (V)
2
1
0
INPUT
VOLTAGE (V)
Voltage follower pulse response
500
RL 2 k W
VCC = +15V
3
2
+
450
eO
el
-
400
Input
350
Output
300
Tamb = +25°C
VCC = 30 V
10
20
30
250
40
0
1
2
TIME (ms)
Input current
Figure 7.
OUTPUT VOLTAGE (V)
VI = 0 V
VCC = +30 V
60
50
VCC = +15 V
40
30
VCC = +5 V
20
-55 -35
5
25
45
65
7
8
1
v cc /2
85 105
TEMPERATURE (°C)
125
v cc
-
0.1
IO
VO
+
Tamb = +25°C
0.01
-15
6
VCC = +5V
VCC = +15V
VCC = +30V
10
0
5
OUTPUT CHARACTERISTICS
10
70
4
Output characteristics
INPUT CURRENT (Note 1)
80
3
TIME (ms)
90
INPUT CURRENT (mA)
50pF
1
0
1M
VOLTAGE FOLLOWER PULSSE RESPONSE
(SMALL SIGNAL)
4
3
100k
FREQUENCY (Hz)
VOLAGE FOLLOWER PULSE RESPONSE
8/20
2k W
+
10
FREQUENCY (Hz)
Figure 6.
VO
0
1.0
Figure 4.
+15V
-
VI
0,001
0,01
0,1
1
10
100
OUTPUT SINK CURRENT (mA)
LM158W-LM258W-LM358W
Output characteristics
Figure 9.
Current limiting
CURRENT LIMITING (Note 1)
OUTPUT CHARACTERISTICS
8
90
OUTPUT CURRENT (mA)
V CC
7
6
TO VCC+ (V)
OUTPUT VOLTAGE REFERENCED
Figure 8.
Electrical characteristics
+
V CC /2
5
VO
IO
-
4
3
2
Independent of V CC
T amb = +25°C
-
80
60
+
50
40
30
20
10
1
0
0,001 0,01
0,1
IO
70
1
10
-55 -35
100
OUTPUT SOURCE CURRENT (mA)
Figure 10. Input voltage range
-15
5
25
45
160
VOLTAGE GAIN (dB)
INPUT VOLTAGE (V)
Négative
Positive
0
5
10
R L = 20k W
120
R L = 2k W
80
40
0
15
10
20
30
40
POSITIVE SUPPLY VOLTAGE (V)
POWER SUPPLY VOLTAGE (±V)
Figure 12. Input voltage range
Figure 13. Supply current
160
SUPPLY CURRENT
4
R L = 20k W
VCC
120
SUPPLY CURRENT (mA)
VOLTAGE GAIN (dB)
125
Figure 11. Positive supply voltage
INPUT VOLTAGE RANGE
5
85 105
TEMPERATURE (°C)
15
10
65
R L = 2k W
80
40
0
10
20
30
POSITIVE SUPPLY VOLTAGE (V)
ID
mA
3
-
2
+
Tamb = 0°C to +125°C
1
Tamb = -55°C
0
10
20
30
POSITIVE SUPPLY VOLTAGE (V)
9/20
Electrical characteristics
LM158W-LM258W-LM358W
INPUT CURRENT (nA)
100
75
50
25
Tamb= +25°C
0
10
20
30
POSITIVE SUPPLY VOLTAGE (V)
POWER SUPPLY REJECTION RATIO (dB)
Figure 16. Power supply rejection ratio
115
110
SVR
105
100
95
90
85
80
75
70
65
60-55-35-15 5 25 45 65 85 105 125
TEMPERATURE (°C)
Figure 18. Phase margin vs capacitive load
Phase Margin at Vcc=15V and Vicm=7.5V
Vs. Iout and Capacitive load value
10/20
GAIN BANDWIDTH PRODUCT (MHz)
Figure 15. Gain bandwidth product
1.5
1.35
1.2
1.05
0.9
0.75
0.6
VCC =
15V
0.45
0.3
0.15
0
-55-35-15 5 25 45 65 85 105 125
TEMPERATURE (°C)
Figure 17. Common mode rejection ratio
COMMON MODE REJECTION RATIO (dB)
Figure 14. Input current
115
110
105
100
95
90
85
80
75
70
65
60-55-35-15 5 25 45 65 85 105 125
TEMPERATURE (°C)
LM158W-LM258W-LM358W
4
Typical applications
Typical applications
Single supply voltage VCC = +5 VDC
Figure 19. AC coupled inverting amplifier
Rf
100k W
R1
10kW
10k W
2VPP
0
eo
RB
6.2kW
R3
100kW
eO
1/2
LM158
Co
1/2
LM158
eI ~
R2
VCC 100k W
A V = 1 + R2
R1
(As shown A V = 101)
Rf
R1
(as shown A V = -10)
+5V
RL
10k W
R2
1M W
e
O
R1
10k W
(V)
CI
AV= -
Figure 20. Non-inverting DC amplifier
C1
10mF
0
Figure 21. AC coupled non-inverting amplifier
R1
100kW
Co
1/2
LM158
100kW
eI ~
2VPP
0
eo
RB
6.2kW
R3
1M W
RL
10k W
e2
100k W
e3
100kW
1/2
LM158
eO
100kW
R4
100kW
e4
VCC
C2
10mF
100kW
A = 1 + R2
V
R1
(as shown A V = 11)
C1
0.1mF
CI
Figure 22. DC summing amplifier
e1
R2
1MW
e I (mV)
R5
100kW
100kW
eo = e1 + e2 - e3 - e4
where (e1 + e2) ≥ (e3 + e4)
to keep eo ≥ 0V
Figure 23. High input Z, DC differential amplifier Figure 24. High input Z adjustable gain DC
instrumentation amplifier
R1
100k W
R4
100kW
R2
100kW
1/2
LM158
e1
R1
100kW
1/2
LM158
R3
100kW
+V1
+V2
R2
2k W
1/2
LM158
R3
100k W
R4
100k W
1/2
LM158
Gain adjust
eO
R5
100k W
Vo
1/2
LM158
R6
100k W
R7
100k W
e2
if R1 = R5 and R3 = R4 = R6 = R7
eo = [1 + 2R1
----------- ] ((e2 + e1)
R2
if R1 = R5 and
R3 = R4 = R6 = R7
eo = [1 + 2R1
-----------] ((e2 + e1)
R2
As shown eo = 101 (e2 + e1)
As shown eo = 101 (e2 + e1)
11/20
Typical applications
LM158W-LM258W-LM358W
Figure 25. Using symmetrical amplifiers to
reduce input current
I
eI
IB
I
IB
1/2
LM158
Figure 26. Low drift peak detector
IB
eo
2N 929
IB
Input current compensation
R1
100kW
C1
330pF
1/2
LM158
R5
470kW
R4
10MW
1/2
LM158
C2
R3
100kW
330 pF
R6
470kW
Vo
1/2
LM158
R7
100kW
VCC
R8
100kW
12/20
C3
10mF
eo
Zo
0.001mF
IB
3R
3MW
IB
Figure 27. Active band-pass filter
+V1
R
1MW
1/2
LM158
2I B
2N 929
2IB
1/2
LM158
1.5MW
R2
100kW
1mF
ZI
IB
3MW
C
eI
0.001mF
IB
IB
1/2
LM158
1/2
LM158
Input current
compensation
LM158W-LM258W-LM358W
5
Package mechanical data
Package mechanical data
In order to meet environmental requirements, STMicroelectronics offers these devices in
ECOPACK® packages. These packages have a lead-free second level interconnect. The
category of second level interconnect is marked on the package and on the inner box label,
in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering
conditions are also marked on the inner box label. ECOPACK is an STMicroelectronics
trademark. ECOPACK specifications are available at: www.st.com.
13/20
Package mechanical data
5.1
LM158W-LM258W-LM358W
DIP8 package
Dimensions
Ref.
Millimeters
Min.
A
Typ.
Max.
Min.
3.3
Typ.
Max.
0.130
a1
0.7
B
1.39
1.65
0.055
0.065
B1
0.91
1.04
0.036
0.041
b
b1
0.028
0.5
0.38
0.020
0.5
D
0.015
0.020
9.8
0.386
E
8.8
0.346
e
2.54
0.100
e3
7.62
0.300
e4
7.62
0.300
F
7.1
0.280
I
4.8
0.189
L
Z
14/20
Inches
3.3
0.44
0.130
1.6
0.017
0.063
LM158W-LM258W-LM358W
5.2
Package mechanical data
SO-8 package
Dimensions
Ref.
Millimeters
Min.
Typ.
Inches
Max.
Min.
Typ.
Max.
A
1.35
1.75
0.053
0.069
A1
0.10
0.25
0.04
0.010
A2
1.10
1.65
0.043
0.065
B
0.33
0.51
0.013
0.020
C
0.19
0.25
0.007
0.010
D
4.80
5.00
0.189
0.197
E
3.80
4.00
0.150
0.157
e
1.27
0.050
H
5.80
6.20
0.228
0.244
h
0.25
0.50
0.010
0.020
L
0.40
1.27
0.016
0.050
k
ddd
8° (max.)
0.1
0.04
15/20
Package mechanical data
5.3
LM158W-LM258W-LM358W
MiniSO-8 package
Dimensions
Ref.
Millimeters
Min.
Typ.
A
Max.
Min.
Typ.
1.1
Max.
0.043
A1
0.05
0.10
0.15
0.002
0.004
0.006
A2
0.78
0.86
0.94
0.031
0.034
0.037
b
0.25
0.33
0.40
0.010
0.13
0.016
c
0.13
0.18
0.23
0.005
0.007
0.009
D
2.90
3.00
3.10
0.114
0.118
0.122
E
4.75
4.90
5.05
0.187
0.193
0.199
E1
2.90
3.00
3.10
0.114
0.118
0.122
e
0.65
K
0°
L
0.40
L1
16/20
Inches
0.55
0.026
6°
0°
0.70
0.016
0.10
6°
0.022
0.028
0.004
LM158W-LM258W-LM358W
5.4
Package mechanical data
TSSOP8 package
Dimensions
Ref.
Millimeters
Min.
Typ.
A
Inches
Max.
Min.
Typ.
1.2
A1
0.05
A2
0.80
b
Max.
0.047
0.15
0.002
1.05
0.031
0.19
0.30
0.007
0.012
c
0.09
0.20
0.004
0.008
D
2.90
3.00
3.10
0.114
0.118
0.122
E
6.20
6.40
6.60
0.244
0.252
0.260
E1
4.30
4.40
4.50
0.169
0.173
0.177
e
0.65
K
0°
L
0.45
L1
1.00
0.60
1
0.006
0.039
0.041
0.0256
8°
0°
0.75
0.018
8°
0.024
0.030
0.039
17/20
Ordering information
6
LM158W-LM258W-LM358W
Ordering information
Temperature
range
Part number
Package
Packaging
Marking
DIP-8
Tube
LM158WN
SO-8
Tube or tape & reel
158W
DIP-8
Tube
LM258WA
SO-8
Tube or tape & reel
258WA
LM258WN
DIP-8
Tube
LM258WN
LM258WD
LM258WDT
SO-8
Tube or tape & reel
258W
LM358WN
DIP-8
Tube
LM358WN
LM158WN
-55°C, +125°C
LM158WD
LM158WDT
LM258WAN
LM258WAD
LM258WADT
-40°C, +105°C
LM358WD
LM358WDT
358W
0°C, +70°C
SO-8
Tube or tape & reel
LM358AWD
LM358AWDT
358AW
LM258WYPT
(automotive grade)(1)
LM258AWYPT
(automotive grade)(1)
LM258WYD
LM258WYDT
(automotive grade)
Tape & reel
K411
TSSOP-8
Tape & reel
K410
SO-8
Tube or tape & reel
258WY
SO-8
Tube or tape & reel
258AWY
SO-8
Tube or tape & reel
358WY
SO-8
Tube or tape & reel
358AWY
TSSOP-8
Tape & reel
K412
TSSOP-8
Tape & reel
K413
(1)
LM258AWYD
LM258AWYDT
(automotive
TSSOP-8
grade)(1)
40°C, +125°C
LM358WYD
LM358WYDT
(automotive grade)(1)
LM358AWYD
LM358AWYDT
(automotive grade)(1)
LM358WYPT
(automotive grade)(1)
LM358AWYPT
(automotive grade)(1)
1. Qualified and characterized according to AEC Q100 and Q003 or equivalent, advanced screening
according to AEC Q001 & Q 002 or equivalent.
18/20
LM158W-LM258W-LM358W
7
Revision history
Revision history
Date
Revision
Changes
1-Nov-2002
1
First release.
1-Jul-2005
2
ESD protection inserted in Table 1: Absolute maximum ratings on
page 4.
6-Oct-2006
3
ESD tolerance for model HBM improved to 2kV (Table 1: Absolute
maximum ratings on page 4).
Rthja and Rthjc typical values added in Table 1: Absolute maximum
ratings on page 4.
Added Figure 18: Phase margin vs capacitive load on page 10.
2-Jan-2007
4
Order codes added (automotive grade level) to Section 6: Ordering
information.
15-Mar-2007
5
Previously called revision 4.
Footnote for automotive grade order codes added to Section 6:
Ordering information.
25-Apr-2007
6
Added missing Revision 4 of January 2007 in revision history.
Corrected revision number of March 2007 to Revision 5.
19/20
LM158W-LM258W-LM358W
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2007 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
20/20