STB13NK60Z - STB13NK60Z-1 STP13NK60Z/FP - STW13NK60Z N-CHANNEL 600V - 0.48Ω - 13A - TO-220/FP - D²/I²PAK - TO-247 Zener-Protected SuperMESH™ MOSFET General features VDSS RDS(on) ID Pw 600 600 600 600 600 <0.55 Ω <0.55 Ω <0.55 Ω <0.55 Ω <0.55 Ω 13 A 13 A 13 A 13 A 13 A 150 W 150 W 35 W 150 W 150 W Type STB13NK60Z-1 STB13NK60Z STP13NK60ZFP STP13NK60Z STW13NK60Z Package V V V V V ■ GATE CHARGE MINIMIZED ■ VERY LOW INTRINSIC CAPACITANCES ■ VERY GOOD MANUFACTURING REPEABILITY 3 1 2 3 12 TO-220 3 1 I²PAK 2 TO-220FP 3 3 1 2 1 TO-247 D²PAK Internal schematic diagram Description The SuperMESH™ series is obtained through an extreme optimization of ST’s well established strip-based PowerMESH™ layout. In addition to pushing on-resistance significantly down, special care is taken to ensure a very good dv/dt capability for the most demanding applications. Applications ■ HIGH CURRENT, HIGH SPEED SWITCHING ■ SWITCH MODE POWER SUPPLIES ■ DC-AC CONVERTERS FOR WELDING, UPS AND MOTOR DRIVE Order codes Sales Type Marking Package Packaging STB13NK60Z-1 B13NK60Z-1 I²PAK TUBE STB13NK60ZT4 B13NK60Z D²PAK TAPE & REEL STP13NK60ZFP P13NK60ZFP TO-220FP TUBE STP13NK60Z P13NK60Z TO-220 TUBE STW13NK60Z W13NK60Z TO-247 TUBE September 2005 Rev 2 1/17 www.st.com 17 1 Electrical ratings 1 STB13NK60Z - STB13NK60Z-1 - STP13NK60Z/FP - STW13NK60Z Electrical ratings Table 1. Absolute maximum ratings Symbol Parameter Value TO-220 / TO-247 TO-220FP I²PAK / D²PAK VDS VDGR VGS Unit Drain-Source Voltage (VGS = 0) 600 V Drain-gate Voltage (RGS = 20kΩ) 600 V Gate-Source Voltage ± 30 V ID Drain Current (continuous) at TC = 25°C 13 13 (Note 1) A ID Drain Current (continuous) at TC = 100°C 8.2 8.2 (Note 1) A Drain Current (pulsed) 52 52 (Note 1) A Total Dissipation at TC = 25°C 150 35 W Derating Factor 1.20 0.27 W/°C IDM Note 2 PTOT Vesd(G-S) G-S ESD (HBM C=100pF, R=1.5kΩ) dv/dt Note 3 Peak Diode Recovery voltage slope VISO Tj Tstg Table 2. Insulation Withstand Volatge (DC) 4000 V 4.5 V/ns -- 2500 Operating Junction Temperature Storage Temperature V -55 to 150 °C Thermal data TO-220 D²PAK I²PAK / TO-247 Unit 3.6 °C/W -- °C/W Rthj-case Thermal Resistance Junction-case Max Rthj-pcb Note 7 Thermal Resistance Junction-pcb Max Rthj-amb Thermal Resistance Junction-amb Max 62.5 °C/W Maximum Lead Temperature For Soldering Purpose 300 °C Tl Table 3. 0.83 TO-220FP -- 60 Avalanche characteristics Symbol Parameter Max Value Unit IAR Avalanche Current, repetitive or Not-Repetitive (pulse width limited by Tj max) 10 A EAS Single Pulse Avalanche Energy (starting Tj=25°C, ID=IAR, VDD = 50V) 400 mJ 2/17 STB13NK60Z - STB13NK60Z-1 - STP13NK60Z/FP - STW13NK60Z 2 2 Electrical characteristics Electrical characteristics (TCASE = 25 °C unless otherwise specified) Table 4. On/off states Symbol Parameter V(BR)DSS Drain-Source Breakdown Voltage IDSS Zero Gate Voltage Drain Current (VGS = 0) IGSS Test Conditions ID = 1 mA, VGS= 0 Min. Typ. Max. 600 Unit V VDS = Max Rating, VDS = Max Rating,Tc=125°C 1 50 µA µA Gate Body Leakage Current (VDS = 0) VGS = ±20 V ±10 µA VGS(th) Gate Threshold Voltage VDS= VGS, ID = 100 µA 3.75 4.5 V RDS(on) Static Drain-Source On Resistance VGS= 10 V, ID= 4.5 A 0.48 0.55 Ω Typ. Max. Unit Table 5. Symbol gfs Note 4 Ciss Coss Crss Coss eq. Note 5 Qg Qgs Qgd Table 6. Symbol td(on) tr td(off) tf tr(Voff) tf tc 3 Dynamic Parameter Forward Transconductance Test Conditions Min. VDS =8V, ID = 5 A 11 S Input Capacitance VDS =25V, f=1 MHz, V GS=0 Output Capacitance Reverse Transfer Capacitance 2030 210 48 pF pF pF Equivalent Ouput Capacitance VGS=0, VDS =0V to 480V 125 pF Total Gate Charge Gate-Source Charge Gate-Drain Charge VDD=480V, ID = 10A VGS =10V (see Figure 19) 66 11 33 92 nC nC nC Typ. Max. Unit Switching times Parameter Turn-on Delay Time Rise Time Turn-off Delay Time Fall Time Off-voltage Rise Time Fall Time Cross-over Time Test Conditions VDD=300 V, ID= 5A, RG=4.7Ω, VGS=10V (see Figure 20) VDD=300 V, ID= 5A, RG=4.7Ω, VGS=10V (see Figure 20) VDD=480 V, ID= 10A, RG=4.7Ω, VGS=10V (see Figure 20) Min. 22 14 ns ns 61 12 ns ns 10 9 20 ns ns ns 3/17 2 Electrical characteristics Table 7. Symbol BVGSO Note 6 Table 8. STB13NK60Z - STB13NK60Z-1 - STP13NK60Z/FP - STW13NK60Z Gate-source zener diode Parameter Gate-Source Breakdown Voltage Test Conditions Igs=±1mA (Open Drain) Parameter ISD ISDMNote 2 Source-drain Current Source-drain Current (pulsed) VSDNote 4 Forward on Voltage ISD = 10 A, VGS=0 Reverse Recovery Time Reverse Recovery Charge Reverse Recovery Current ISD= 10A, di/dt = 100A/µs, VDD=35 V, Tj=150°C Qrr IRRM Typ. Max. Unit 30 V Source drain diode Symbol trr Min. Test Conditions Min. Typ. 570 4.5 16 Max. Unit 10 40 A A 1.6 V ns µC A (1) Limited only by maximum temperature allowed (2) Pulse width limited by safe operating area (3) ISD ≤13A, di/dt ≤200A/µs, VDD ≤ V(BR)DSS , Tj ≤ TJMAX (4) Pulsed: pulse duration = 300µs, duty cycle 1.5% (5) Coss eq. is defined as a constant equivalent capacitance giving the same charging time as Coss when VDS increases from 0 to 80% (6) The built-in back-to-back Zener diodes have specifically been designed to enhance not only the device’s ESD capability, but also to make them safely absorb possible voltage transients that may occasionally be applied from gate to source. In this respect the Zener voltage is appropriate to achieve an efficient and cost-effective intervention to protect the device’s integrity. These integrated Zener diodes thus avoid the usage of external components. (7) When mounted on minimum Footprint 4/17 STB13NK60Z - STB13NK60Z-1 - STP13NK60Z/FP - STW13NK60Z 2.1 2 Electrical characteristics Electrical characteristics (curves) Figure 1. Safe Operating Area for TO-220/ D²PAK/ I²PAK Figure 2. Thermal Impedanc for TO-220/ D²PAK/ I²PAK Figure 3. Safe Operating Area for TO-220FP Figure 4. Thermal Impedance for TO-220FP Figure 5. Safe Operating Area for TO-247 Figure 6. Thermal Impedance for TO-247 5/17 2 Electrical characteristics STB13NK60Z - STB13NK60Z-1 - STP13NK60Z/FP - STW13NK60Z Figure 7. Output Characteristics Figure 8. Figure 9. Transconductance Figure 10. Static Drain-Source on Resistance Figure 11. Gate Charge vs Gate -Source Voltage 6/17 Transfer Characteristics Figure 12. Capacitance Variations STB13NK60Z - STB13NK60Z-1 - STP13NK60Z/FP - STW13NK60Z 2 Electrical characteristics Figure 13. Normalized Gate Threshold Voltage Figure 14. Normalized on Resistance vs vs Temperatute Temperature Figure 15. Source-drain Diode Forward Characteristics Figure 16. Normalized BVDSS vs Temperature Figure 17. Maximum Avalanche Energy vs Temperature 7/17 3 Test circuits 3 STB13NK60Z - STB13NK60Z-1 - STP13NK60Z/FP - STW13NK60Z Test circuits Figure 18. Switching Times Test Circuit For Resistive Load Figure 20. Test Circuit For Inductive Load Switching and Diode Recovery Times 8/17 Figure 19. Gate Charge Test Circuit STB13NK60Z - STB13NK60Z-1 - STP13NK60Z/FP - STW13NK60Z 4 4 Package mechanical data Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a Lead-free second level interconnect . The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com 9/17 4 Package mechanical data STB13NK60Z - STB13NK60Z-1 - STP13NK60Z/FP - STW13NK60Z TO-220 MECHANICAL DATA DIM. mm. MIN. inch MAX. MIN. TYP. MAX. A 4.40 4.60 0.173 0.181 b 0.61 0.88 0.024 0.034 b1 1.15 1.70 0.045 0.066 c 0.49 0.70 0.019 0.027 D 15.25 15.75 0.60 0.620 E 10 10.40 0.393 0.409 e 2.40 2.70 0.094 0.106 e1 4.95 5.15 0.194 0.202 F 1.23 1.32 0.048 0.052 H1 6.20 6.60 0.244 0.256 J1 2.40 2.72 0.094 0.107 0.551 L 13 14 0.511 L1 3.50 3.93 0.137 L20 16.40 L30 10/17 TYP 0.154 0.645 28.90 1.137 øP 3.75 3.85 0.147 0.151 Q 2.65 2.95 0.104 0.116 STB13NK60Z - STB13NK60Z-1 - STP13NK60Z/FP - STW13NK60Z 4 Package mechanical data TO-220FP MECHANICAL DATA mm. DIM. MIN. A 4.4 inch TYP MAX. MIN. TYP. 4.6 0.173 0.181 MAX. 0.106 B 2.5 2.7 0.098 D 2.5 2.75 0.098 0.108 E 0.45 0.7 0.017 0.027 F 0.75 1 0.030 0.039 F1 1.15 1.7 0.045 0.067 F2 1.15 1.7 0.045 0.067 G 4.95 5.2 0.195 0.204 G1 2.4 2.7 0.094 0.106 H 10 10.4 0.393 0.409 L2 16 0.630 L3 28.6 30.6 1.126 1.204 L4 9.8 10.6 .0385 0.417 L5 2.9 3.6 0.114 0.141 L6 15.9 16.4 0.626 0.645 9 9.3 0.354 0.366 Ø 3 3.2 0.118 0.126 B D A E L7 L3 L6 F2 H G G1 F F1 L7 L2 L5 1 2 3 L4 11/17 4 Package mechanical data STB13NK60Z - STB13NK60Z-1 - STP13NK60Z/FP - STW13NK60Z TO-262 (I2PAK) MECHANICAL DATA mm. inch DIM. MIN. 12/17 TYP MAX. MIN. TYP. MAX. A 4.40 4.60 0.173 0.181 A1 2.40 2.72 0.094 0.107 b 0.61 0.88 0.024 0.034 b1 1.14 1.70 0.044 0.066 c 0.49 0.70 0.019 0.027 c2 1.23 1.32 0.048 0.052 D 8.95 9.35 0.352 0.368 e 2.40 2.70 0.094 0.106 e1 4.95 5.15 0.194 0.202 E 10 10.40 0.393 0.410 L 13 14 0.511 0.551 L1 3.50 3.93 0.137 0.154 L2 1.27 1.40 0.050 0.055 STB13NK60Z - STB13NK60Z-1 - STP13NK60Z/FP - STW13NK60Z 4 Package mechanical data D2PAK MECHANICAL DATA TO-247 MECHANICAL DATA mm. inch DIM. MAX. MIN. A MIN. 4.4 TYP 4.6 0.173 TYP. 0.181 MAX. A1 2.49 2.69 0.098 0.106 A2 0.03 0.23 0.001 0.009 B 0.7 0.93 0.027 0.036 B2 1.14 1.7 0.044 0.067 C 0.45 0.6 0.017 0.023 C2 1.23 1.36 0.048 0.053 D 8.95 9.35 0.352 D1 E 8 10 E1 G 0.368 0.315 10.4 0.393 8.5 0.334 4.88 5.28 0.192 0.208 L 15 15.85 0.590 0.625 L2 1.27 1.4 0.050 0.055 L3 1.4 1.75 0.055 0.068 M 2.4 3.2 0.094 0.126 R 0.4 0º 0.015 4º 3 V2 1 13/17 4 Package mechanical data STB13NK60Z - STB13NK60Z-1 - STP13NK60Z/FP - STW13NK60Z TO-247 MECHANICAL DATA DIM. mm. MIN. inch MAX. MIN. TYP. MAX. A 4.85 5.15 0.19 0.20 A1 2.20 2.60 0.086 0.102 b 1.0 1.40 0.039 0.055 b1 2.0 2.40 0.079 0.094 0.134 b2 3.0 3.40 0.118 c 0.40 0.80 0.015 0.03 D 19.85 20.15 0.781 0.793 E 15.45 15.75 0.608 e 5.45 0.620 0.214 L 14.20 14.80 0.560 L1 3.70 4.30 0.14 L2 18.50 0.582 0.17 0.728 øP 3.55 3.65 0.140 0.143 øR 4.50 5.50 0.177 0.216 S 14/17 TYP 5.50 0.216 STB13NK60Z - STB13NK60Z-1 - STP13NK60Z/FP - STW13NK60Z 5 5 Packing mechanical data Packing mechanical data D2PAK FOOTPRINT TAPE AND REEL SHIPMENT REEL MECHANICAL DATA DIM. mm MIN. A B 1.5 C 12.8 D 20.2 G 24.4 N 100 T TAPE MECHANICAL DATA DIM. mm inch MIN. MAX. MIN. A0 10.5 10.7 0.413 0.421 B0 15.7 15.9 0.618 0.626 D 1.5 1.6 0.059 0.063 D1 1.59 1.61 0.062 0.063 E 1.65 1.85 0.065 0.073 F 11.4 11.6 0.449 0.456 inch MAX. MIN. MAX. 330 12.992 13.2 0.504 0.520 26.4 0.960 1.039 0.059 0795 3.937 30.4 1.197 BASE QTY BULK QTY 1000 1000 MAX. K0 4.8 5.0 0.189 0.197 P0 3.9 4.1 0.153 0.161 P1 11.9 12.1 0.468 0.476 P2 1.9 2.1 0.075 0.082 R 50 1.574 T 0.25 0.35 0.0098 0.0137 W 23.7 24.3 0.933 0.956 * on sales type 15/17 6 Revision History 6 16/17 STB13NK60Z - STB13NK60Z-1 - STP13NK60Z/FP - STW13NK60Z Revision History Date Revision 12-Sep-2005 2 Changes Inserted ecopack indication STB13NK60Z - STB13NK60Z-1 - STP13NK60Z/FP - STW13NK60Z 6 Revision History Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners © 2005 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 17/17