STP14NK60Z - STP14NK60ZFP STB14NK60Z/-1 - STW14NK60Z N-channel 600V - 0.45Ω - 13.5A TO-220/FP-D2/I2PAK-TO-247 Zener-protected SuperMESHTM Power MOSFET General features Type VDSS RDS(on) ID Pw STP14NK60Z 600V <0.5Ω 13.5A 160W 3 1 STP14NK60ZFP 600V <0.5Ω 13.5A 40W STB14NK60Z 600V <0.5Ω 13.5A 160W STB14NK60Z-1 600V <0.5Ω 13.5A 160W STW14NK60Z 600V <0.5Ω 13.5A 160W ■ Extremely high dv/dt capability ■ 100% avalanche tested ■ Gate charge minimized ■ Very low intrinsic capacitances ■ Very good manufacturing repeatibility 3 2 1 TO-220 2 TO-220FP TO-247 3 3 12 1 I2PAK D2PAK Internal schematic diagram Description The SuperMESH™ series is obtained through an extreme optimization of ST’s well established strip-based PowerMESH™ layout. In addition to pushing on-resistance significantly down, special care is taken to ensure a very good dv/dt capability for the most demanding applications. Such series complements ST full range of high voltage MOSFETs including revolutionary MDmesh™ products. Applications ■ Switching application Order codes Part number Marking Package Packaging STP14NK60Z P14NK60Z TO-220 Tube STP14NK60ZFP P14NK60ZFP TO-220FP Tube STB14NK60ZT4 2 D PAK B14NK60Z 2 Tape & reel STB14NK60Z-1 B14NK60Z I PAK Tube STW14NK60Z W14NK60Z TO-247 Tube July 2006 Rev 7 1/19 www.st.com 19 Contents STP14NK60Z-STP14NK60ZFP-STB14NK60Z-STB14NK60Z-1-STW14NK60Z Contents 1 Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.1 Electrical characteristics (curves) ............................. 7 3 Test circuit 4 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 5 Packaging mechanical data 6 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 2/19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 STP14NK60Z-STP14NK60ZFP-STB14NK60Z-STB14NK60Z-1-STW14NK60Z 1 Electrical ratings Electrical ratings Table 1. Absolute maximum ratings Value Symbol Parameter TO-220/D²PAK/I²PAK TO-247 VDS VDGR VGS Unit TO-220FP Drain-source voltage (VGS = 0) 600 V Drain-gate voltage (RGS = 20KΩ) 600 V Gate-source voltage ± 30 V ID Drain current (continuous) at TC = 25°C 13.5 13.5(1) ID Drain current (continuous) at TC=100°C 8.5 8.5(1) A (1) A A IDM(2) Drain current (pulsed) 54 PTOT Total dissipation at TC = 25°C 160 40 W Derating factor 1.28 0.32 W/°C VESD(G-S) 54 Gate source ESD (HBM-C= 100pF, R= 1.5kΩ) dv/dt(3) Peak diode recovery voltage slope VISO Insulation withstand voltage (DC) TJ Tstg Operating junction temperature Storage temperature 4000 V 4.5 V/ns -- 2500 -55 to 150 V °C 1. Limited only by maximum temperature allowed 2. Pulse width limited by safe operating area 3. ISD ≤13.5A, di/dt ≤200A/µs, VDD≤V(BR)DSS, Tj ≤TJMAX. Table 2. Thermal data Value Symbol Parameter TO-220/D²PAK/I²PAK TO-247 Rthj-case Rthj-a Tl Unit TO-220FP Thermal resistance junction-case Max 0.78 3.1 °C/W Thermal resistance junction-ambient Max 62.5 50 °C/W Maximum lead temperature for soldering purpose 300 °C 3/19 Electrical ratings Table 3. STP14NK60Z-STP14NK60ZFP-STB14NK60Z-STB14NK60Z-1-STW14NK60Z Avalanche characteristics Symbol Parameter Value Unit IAS Avalanche current, repetitive or not-repetitive (pulse width limited by Tj Max) 12 A EAS Single pulse avalanche energy (starting Tj=25°C, Id=Iar, Vdd=50V) 300 mJ Table 4. Gate-source zener diode Symbol Parameter BVGSO(1) Gate-source breakdown voltage Test conditions Igs=±1mA (Open Drain) Min. Typ. Max. Unit 30 1. The built-in back-to-back Zener diodes have specifically been designed to enhance not only the device’s ESD capability, but also to make them safely absorb possible voltage transients that may occasionally be applied from gate to source. In this respect the Zener voltage is appropriate to achieve an efficient and cost-effective intervention to protect the device’s integrity. These integrated Zener diodes thus avoid the usage of external components. 4/19 V STP14NK60Z-STP14NK60ZFP-STB14NK60Z-STB14NK60Z-1-STW14NK60Z Electrical characteris- 2 Electrical characteristics (TCASE=25°C unless otherwise specified) Table 5. Symbol V(BR)DSS On/off states Parameter Drain-source breakdown voltage Test conditions ID = 1mA, VGS= 0 Min. Typ. Max. 600 Unit V VDS = Max rating, VDS = Max rating @125°C 1 50 µA µA Gate body leakage current (VDS = 0) VGS = ±30V ±10 nA VGS(th) Gate threshold voltage VDS= VGS, ID = 100µA 3.75 4.5 V RDS(on) Static drain-source on resistance VGS= 10V, ID= 6A 0.45 0.5 Ω IDSS Zero gate voltage drain current (VGS = 0) IGSS Table 6. Symbol gfs (1) Ciss Coss Crss Dynamic Parameter Qg Qgd Test conditions Forward transconductance VDS =15V, ID = 6A Input capacitance Output capacitance Reverse transfer capacitance Coss eq(2). Equivalent output capacitance Qgs 3 Total gate charge Gate-source charge Gate-drain charge Min. Typ. Max. Unit 11 S VDS =25V, f=1 MHz, VGS=0 2220 240 57 pF pF pF VGS=0, VDS =0V to 480V 122 pF 75 13.2 38.6 nC nC nC VDD=480V, ID = 12A VGS =10V 1. Pulsed: pulse duration=300µs, duty cycle 1.5% 2. Coss eq. is defined as a constant equivalent capacitance giving the same charging time as Coss when VDS inceases from 0 to 80% VDSS 5/19 Electrical characteristics Table 7. Symbol td(on) tr td(off) tf tr(Voff) tf tc Table 8. Symbol STP14NK60Z-STP14NK60ZFP-STB14NK60Z-STB14NK60Z-1- Switching times Parameter Turn-on delay time Rise time Turn-off delay time Fall time Off-voltage rise time Fall time Cross-over time Min. VDD=300 V, ID=6A, RG=4.7Ω, VGS=10V (see Figure 18) VDD=300V, ID=6A, RG=4.7Ω, VGS=10V (see Figure 18) VDD=480 V, ID=12A, RG=4.7Ω, VGS=10V (see Figure 20) Typ. Max. Unit 26 18 ns ns 62 13 ns ns 12 9.5 22 ns ns ns Source drain diode Max Unit Source-drain current 12 A ISDM(1) Source-drain current (pulsed) 48 A VSD(2) Forward on voltage ISD=12A, VGS=0 1.6 V Reverse recovery time Reverse recovery charge Reverse recovery current ISD=12A, ISD trr Qrr IRRM trr Qrr IRRM Parameter Reverse recovery time Reverse recovery charge Reverse recovery current 1. Pulse width limited by safe operating area 2. Pulsed: pulse duration=300µs, duty cycle 1.5% 6/19 Test conditions Test conditions di/dt = 100A/µs, VDD=50V ISD=12A, di/dt = 100A/µs, VDD=50V, Tj=150°C Min Typ. 490 4.7 19.3 ns µC A 664 6.8 20.5 ns µC A STP14NK60Z-STP14NK60ZFP-STB14NK60Z-STB14NK60Z-1-STW14NK60Z Electrical characteris- 2.1 Electrical characteristics (curves) Figure 1. Safe operating area for TO220/D2PAK/I2PAK Figure 2. Thermal impedance for TO220/D2PAK/I2PAK Figure 3. Safe operating area for TO-220FP Figure 4. Thermal impedance for TO-220FP Figure 5. Safe operating area for TO-247 Figure 6. Thermal impedance for TO-247 7/19 Electrical characteristics STP14NK60Z-STP14NK60ZFP-STB14NK60Z-STB14NK60Z-1- Figure 7. Output characterisics Figure 8. Transfer characteristics Figure 9. Transconductance Figure 10. Static drain-source on resistance Figure 11. Gate charge vs gate-source voltage Figure 12. Capacitance variations 8/19 STP14NK60Z-STP14NK60ZFP-STB14NK60Z-STB14NK60Z-1-STW14NK60Z Electrical characterisFigure 13. Normalized gate threshold voltage vs temperature Figure 14. Normalized on resistance vs temperature Figure 15. Source-drain diode forward characteristics Figure 16. Normalized BVDSS vs temperature Figure 17. Maximum avalanche energy vs temperature Normalized BVDSS vs temperatu 9/19 Test circuit 3 STP14NK60Z-STP14NK60ZFP-STB14NK60Z-STB14NK60Z-1-STW14NK60Z Test circuit Figure 18. Switching times test circuit for resistive load Figure 19. Gate charge test circuit Figure 20. Test circuit for inductive load Figure 21. Unclamped Inductive load test switching and diode recovery times circuit Figure 22. Unclamped inductive waveform 10/19 Figure 23. Switching time waveform STP14NK60Z-STP14NK60ZFP-STB14NK60Z-STB14NK60Z-1-STW14NK60Z 4 Package mechanical Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a Lead-free second level interconnect . The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com 11/19 Package mechanical data STP14NK60Z-STP14NK60ZFP-STB14NK60Z-STB14NK60Z-1- TO-220 MECHANICAL DATA DIM. mm. MIN. inch MAX. MIN. TYP. MAX. A 4.40 4.60 0.173 0.181 b 0.61 0.88 0.024 0.034 b1 1.15 1.70 0.045 0.066 c 0.49 0.70 0.019 0.027 D 15.25 15.75 0.60 0.620 E 10 10.40 0.393 0.409 e 2.40 2.70 0.094 0.106 e1 4.95 5.15 0.194 0.202 F 1.23 1.32 0.048 0.052 H1 6.20 6.60 0.244 0.256 J1 2.40 2.72 0.094 0.107 0.551 L 13 14 0.511 L1 3.50 3.93 0.137 L20 16.40 L30 12/19 TYP 0.154 0.645 28.90 1.137 øP 3.75 3.85 0.147 0.151 Q 2.65 2.95 0.104 0.116 STP14NK60Z-STP14NK60ZFP-STB14NK60Z-STB14NK60Z-1-STW14NK60Z Package mechanical TO-220FP MECHANICAL DATA mm. DIM. MIN. A 4.4 inch TYP MAX. MIN. TYP. 4.6 0.173 0.181 MAX. 0.106 B 2.5 2.7 0.098 D 2.5 2.75 0.098 0.108 E 0.45 0.7 0.017 0.027 F 0.75 1 0.030 0.039 F1 1.15 1.7 0.045 0.067 F2 1.15 1.7 0.045 0.067 G 4.95 5.2 0.195 0.204 G1 2.4 2.7 0.094 0.106 H 10 10.4 0.393 0.409 L2 16 0.630 L3 28.6 30.6 1.126 1.204 L4 9.8 10.6 .0385 0.417 L5 2.9 3.6 0.114 0.141 L6 15.9 16.4 0.626 0.645 9 9.3 0.354 0.366 Ø 3 3.2 0.118 0.126 B D A E L7 L3 L6 F2 H G G1 F F1 L7 L2 L5 1 2 3 L4 13/19 Package mechanical data STP14NK60Z-STP14NK60ZFP-STB14NK60Z-STB14NK60Z-1- D2PAK MECHANICAL DATA TO-247 MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 4.4 4.6 0.173 0.181 A1 2.49 2.69 0.098 0.106 A2 0.03 0.23 0.001 0.009 B 0.7 0.93 0.027 0.036 B2 1.14 1.7 0.044 0.067 C 0.45 0.6 0.017 0.023 C2 1.23 1.36 0.048 0.053 D 8.95 9.35 0.352 0.368 10.4 0.393 D1 E 8 10 E1 0.315 8.5 0.334 G 4.88 5.28 0.192 0.208 L 15 15.85 0.590 0.625 L2 1.27 1.4 0.050 0.055 L3 1.4 1.75 0.055 0.068 M 2.4 3.2 0.094 R 0º 0.126 0.015 4º 3 V2 0.4 1 14/19 STP14NK60Z-STP14NK60ZFP-STB14NK60Z-STB14NK60Z-1-STW14NK60Z Package mechanical TO-262 (I2PAK) MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 4.40 4.60 0.173 0.181 A1 2.40 2.72 0.094 0.107 b 0.61 0.88 0.024 0.034 b1 1.14 1.70 0.044 0.066 c 0.49 0.70 0.019 0.027 c2 1.23 1.32 0.048 0.052 D 8.95 9.35 0.352 0.368 e 2.40 2.70 0.094 0.106 e1 4.95 5.15 0.194 0.202 E 10 10.40 0.393 0.410 L 13 14 0.511 0.551 L1 3.50 3.93 0.137 0.154 L2 1.27 1.40 0.050 0.055 15/19 Package mechanical data STP14NK60Z-STP14NK60ZFP-STB14NK60Z-STB14NK60Z-1- TO-247 MECHANICAL DATA DIM. mm. MIN. inch MAX. MIN. TYP. MAX. A 4.85 5.15 0.19 0.20 A1 2.20 2.60 0.086 0.102 b 1.0 1.40 0.039 0.055 b1 2.0 2.40 0.079 0.094 0.134 b2 3.0 3.40 0.118 c 0.40 0.80 0.015 0.03 D 19.85 20.15 0.781 0.793 E 15.45 15.75 0.608 e 5.45 0.620 0.214 L 14.20 14.80 0.560 L1 3.70 4.30 0.14 L2 18.50 0.582 0.17 0.728 øP 3.55 3.65 0.140 0.143 øR 4.50 5.50 0.177 0.216 S 16/19 TYP 5.50 0.216 STP14NK60Z-STP14NK60ZFP-STB14NK60Z-STB14NK60Z-1-STW14NK60Z Packaging mechanical 5 Packaging mechanical data D2PAK FOOTPRINT TAPE AND REEL SHIPMENT REEL MECHANICAL DATA DIM. mm MIN. A B 1.5 C 12.8 D 20.2 G 24.4 N 100 T TAPE MECHANICAL DATA DIM. mm inch MIN. MAX. MIN. A0 10.5 10.7 0.413 0.421 B0 15.7 15.9 0.618 0.626 D 1.5 1.6 0.059 0.063 D1 1.59 1.61 0.062 0.063 E 1.65 1.85 0.065 0.073 F 11.4 11.6 0.449 0.456 K0 4.8 5.0 0.189 0.197 P0 3.9 4.1 0.153 0.161 P1 11.9 12.1 0.468 0.476 P2 1.9 2.1 0.075 0.082 inch MAX. MIN. MAX. 330 12.992 13.2 0.504 0.520 26.4 0.960 1.039 0.059 0795 3.937 30.4 1.197 BASE QTY BULK QTY 1000 1000 MAX. R 50 1.574 T 0.25 0.35 0.0098 0.0137 W 23.7 24.3 0.933 0.956 * on sales type 17/19 Revision history 6 STP14NK60Z-STP14NK60ZFP-STB14NK60Z-STB14NK60Z-1-STW14NK60Z Revision history Table 9. 18/19 Revision history Date Revision Changes 30-Aug-2004 3 Preliminary version 17-Aug-2005 4 Complete version with curves 08-Sep-2005 5 Inserted ecopack indication 14-Oct-2005 6 New package inserted: TO-247 26-Jul-2006 7 New template, no content change STP14NK60Z-STP14NK60ZFP-STB14NK60Z-STB14NK60Z-1-STW14NK60Z Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2006 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 19/19