STB4NK60Z, STB4NK60Z-1, STD4NK60Z STD4NK60Z-1, STP4NK60Z,STP4NK60ZFP N-channel 600 V - 1.76 Ω - 4 A SuperMESH™ Power MOSFET DPAK - D2PAK - IPAK - I2PAK - TO-220 - TO-220FP Features Type VDSS STB4NK60Z STB4NK60Z-1 STD4NK60Z STD4NK60Z-1 STP4NK60Z STP4NK60ZFP 600 V 600 V 600 V 600 V 600 V 600 V RDS(on) max PW ID <2Ω <2Ω <2Ω <2Ω <2Ω <2Ω 70 W 70 W 70 W 70 W 70 W 25 W 1 4A 4A 4A 4A 4A 4A TO-220 100% avalanche tested ■ Very low intrinsic capacitances Figure 1. 3 3 1 D²PAK I²PAK Application 3 1 DPAK IPAK 3 12 ■ ■ 3 2 1 3 2 1 2 TO-220FP Internal schematic diagram Switching applications Description The SuperMESH™ series is obtained through an extreme optimization of ST’s well established strip-based PowerMESH™ layout. In addition to pushing on-resistance significantly down, special care is taken to ensure a very good dv/dt capability for the most demanding applications. Such series complements ST full range of high voltage MOSFETs including revolutionary MDmesh™ products. Table 1. Device summary Order codes Marking Package Packaging STB4NK60Z B4NK60Z D²PAK Tape and reel STB4NK60Z-1 B4NK60Z I²PAK Tube STD4NK60Z D4NK60Z DPAK Tape and reel STD4NK60Z-1 D4NK60Z IPAK Tube STP4NK60Z P4NK60Z TO-220 Tube STP4NK60ZFP P4NK60ZFP TO-220FP Tube April 2008 Rev 6 1/20 www.st.com 20 Contents STB4NK60Zx, STD4NK60Zx, STP4NK60Z, STP4NK60ZFP Contents 1 Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.1 Electrical characteristics (curves) ............................ 6 3 Test circuits 4 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 5 Packaging mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 6 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 2/20 .............................................. 9 STB4NK60Zx, STD4NK60Zx, STP4NK60Z, STP4NK60ZFP 1 Electrical ratings Electrical ratings Table 2. Absolute maximum ratings Value Symbol Parameter VDS Drain-source voltage (VGS = 0) 600 VGS Gate- source voltage ± 30 Drain current (continuous) at TC = 25 °C ID IDM (2) PTOT 2.5 (1) A 2.5 (1) A 16 (1) A 16 Total dissipation at TC = 25 °C 70 25 W 0.56 0.2 W/°C Peak diode recovery voltage slope VISO Insulation withstand voltage (RMS) from all three leads to external heat sink (t=1 s; TC = 25 °C) Tstg Storage temperature Tj V 4 VESD(G-S) Gate source ESD(HBM-C=100 pF, R=1.5 kΩ) dv/dt V Drain current (pulsed) Derating factor (3) TO-220FP 4 Drain current (continuous) at TC = 100 °C ID Unit TO-220 - D²PAK DPAK-IPAK-I²PAK 3000 V 4.5 V/ns - 2500 V -55 to 150 °C 150 °C Max operating junction temperature 1. Limited only by maximum temperature allowed 2. Pulse width limited by safe operating area 3. ISD ≤ 4 A, di/dt ≤ 200 A/µs, VDD ≤ V(BR)DSS, TJ ≤ TJMAX. Table 3. Thermal data Value Symbol Parameter Rthj-case Thermal resistance junction-case max Rthj-amb Thermal resistance junction-ambient max Tl Maximum lead temperature for soldering purpose Table 4. Symbol TO-220 D²PAK I²PAK DPAK IPAK Unit TO-220FP 1.78 62.5 100 300 5 °C/W 62.5 °C/W °C Avalanche characteristics Parameter IAR Avalanche current, repetitive or not-repetitive (pulse width limited by Tj Max) EAS Single pulse avalanche energy (starting TJ = 25 °C, ID=IAR, VDD= 50 V) Value Unit 4 A 120 mJ 3/20 Electrical characteristics 2 STB4NK60Zx, STD4NK60Zx, STP4NK60Z, STP4NK60ZFP Electrical characteristics (TCASE = 25 °C unless otherwise specified) Table 5. On/off states Symbol Parameter V(BR)DSS Drain-source breakdown voltage Test conditions ID =1 mA, VGS = 0 Zero gate voltage drain current (VGS = 0) IGSS Gate-body leakage current (VDS = 0) VGS = ± 20 V VGS(th) Gate threshold voltage VDS = VGS, ID = 50 µA RDS(on) Static drain-source on resistance VGS = 10 V, ID = 2 A Symbol gfs (1) Typ. Max. Unit 600 V VDS = Max rating IDSS Table 6. Min. 1 50 µA µA ± 10 µA 3.75 4.5 V 1.76 2 Ω Max. Unit VDS = Max rating, TC = 125 °C 3 Dynamic Parameter VDS = 15 V, ID = 2 A Min. Typ. 3 S Input capacitance VDS = 25 V, f = 1 MHz, Output capacitance V =0 Reverse transfer capacitance GS 510 67 13 pF pF pF Coss eq. (2) Equivalent output capacitance VDS =0, VDS = 0 to 480 V 38.5 pF td(on) tr td(off) tf Turn-on delay time Rise time Turn-off delay time Fall time VDD = 300 V, ID = 2 A, RG = 4.7 Ω, VGS = 10 V (see Figure 17) 12 9.5 29 16.5 ns ns ns ns tr(Voff) tr tc Off-voltage rise time Fall time Cross-over time VDD = 480 V, ID = 4 A, RG = 4.7 Ω, VGS = 10 V (see Figure 19) 12 12 19.5 ns ns ns Qg Qgs Qgd Total gate charge Gate-source charge Gate-drain charge VDD = 480 V, ID = 4 A, VGS = 10 V (see Figure 18) 18.8 3.8 9.8 Ciss Coss Crss Forward transconductance Test conditions 26 nC nC nC 1. Pulsed: pulse duration=300µs, duty cycle 1.5% 2. Coss eq. is defined as a constant equivalent capacitance giving the same charging time as Coss when VDS increases from 0 to 80% VDSS. 4/20 STB4NK60Zx, STD4NK60Zx, STP4NK60Z, STP4NK60ZFP Table 7. Symbol ISD Source drain diode Parameter Test conditions ISDM(1) Source-drain current Source-drain current (pulsed) VSD(2) Forward on voltage ISD = 4 A, VGS = 0 Reverse recovery time Reverse recovery charge Reverse recovery current ISD = 4 A, di/dt = 100 A/µs trr Qrr IRRM Electrical characteristics Min. Typ. Max. Unit 4 16 A A 1.6 V 400 1700 8.5 VDD = 24 V, Tj = 150 °C (see Figure 19) ns nC A 1. Pulsed: pulse duration = 300 µs, duty cycle 1.5% 2. Pulse width limited by safe operating area Table 8. Symbol Gate-source Zener diode Parameter Test conditions BVGSO (1) Gate-source breakdown voltage Igs=± 1 mA (open drain) Min. Typ. Max. Unit 30 V 1. The built-in back-to-back Zener diodes have specifically been designed to enhance not only the device’s ESD capability, but also to make them safely absorb possible voltage transients that may occasionally be applied from gate to source. In this respect the Zener voltage is appropriate to achieve an efficient and cost-effective intervention to protect the device’s integrity. These integrated Zener diodes thus avoid the usage of external components. 5/20 Electrical characteristics STB4NK60Zx, STD4NK60Zx, STP4NK60Z, STP4NK60ZFP 2.1 Electrical characteristics (curves) Figure 2. Safe operating area for TO-220 / DPAK / IPAK / D²PAK / I²PAK Figure 3. Thermal impedance for TO-220 / DPAK / IPAK / D²PAK / I²PAK Figure 4. Safe operating area for TO-220FP Figure 5. Thermal impedance for TO-220FP Figure 6. Output characteristics Figure 7. Transfer characteristics 6/20 STB4NK60Zx, STD4NK60Zx, STP4NK60Z, STP4NK60ZFP Figure 8. Transconductance Figure 9. Electrical characteristics Static drain-source on resistance Figure 10. Gate charge vs gate-source voltage Figure 11. Capacitance variations Figure 12. Normalized gate threshold voltage vs temperature Figure 13. Normalized BVDSS vs temperature 7/20 Electrical characteristics STB4NK60Zx, STD4NK60Zx, STP4NK60Z, STP4NK60ZFP Figure 14. Normalized on resistance vs temperature Figure 16. Avalanche energy vs temperature 8/20 Figure 15. Source-drain diode forward characteristic STB4NK60Zx, STD4NK60Zx, STP4NK60Z, STP4NK60ZFP 3 Test circuits Test circuits Figure 17. Switching times test circuit for resistive load Figure 18. Gate charge test circuit Figure 19. Test circuit for inductive load Figure 20. Unclamped Inductive load test switching and diode recovery times circuit Figure 21. Unclamped inductive waveform Figure 22. Switching time waveform 9/20 Package mechanical data 4 STB4NK60Zx, STD4NK60Zx, STP4NK60Z, STP4NK60ZFP Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a lead-free second level interconnect . The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com 10/20 STB4NK60Zx, STD4NK60Zx, STP4NK60Z, STP4NK60ZFP Package mechanical data TO-220 mechanical data mm inch Dim Min A b b1 c D D1 E e e1 F H1 J1 L L1 L20 L30 ∅P Q Typ 4.40 0.61 1.14 0.48 15.25 Max Min 4.60 0.88 1.70 0.70 15.75 0.173 0.024 0.044 0.019 0.6 10.40 2.70 5.15 1.32 6.60 2.72 14 3.93 0.393 0.094 0.194 0.048 0.244 0.094 0.511 0.137 1.27 10 2.40 4.95 1.23 6.20 2.40 13 3.50 Max 0.181 0.034 0.066 0.027 0.62 0.050 16.40 28.90 3.75 2.65 Typ 0.409 0.106 0.202 0.051 0.256 0.107 0.551 0.154 0.645 1.137 3.85 2.95 0.147 0.104 0.151 0.116 11/20 Package mechanical data STB4NK60Zx, STD4NK60Zx, STP4NK60Z, STP4NK60ZFP TO-220FP mechanical data mm. Dim. Min. A 4.40 inch Typ Max. Min. 4.60 0.173 Typ. 0.181 Max. B 2.5 2.7 0.098 0.106 D 2.5 2.75 0.098 0.108 E 0.45 0.70 0.017 0.027 F 0.75 1.00 0.030 0.039 F1 1.15 1.50 0.045 0.067 F2 1.15 1.50 0.045 0.067 G 4.95 5.20 0.195 0.204 G1 2.40 2.70 0.094 0.106 H 10 10.40 0.393 L2 16 0.409 0.630 28.6 30.6 1.126 L4 9.80 10.60 0.385 1.204 0.417 L5 2.9 3.6 0.114 0.141 L6 15.90 16.40 0.626 0.645 L7 9 9.30 0.354 0.366 Dia 3 3.2 0.118 0.126 B D A E L3 L3 L6 F2 H G G1 Dia F F1 L7 L2 L5 1 2 3 L4 7012510-I 12/20 STB4NK60Zx, STD4NK60Zx, STP4NK60Z, STP4NK60ZFP Package mechanical data I²PAK (TO-262) mechanical data mm inch Dim Min A A1 b b1 c c2 D e e1 E L L1 L2 4.40 2.40 0.61 1.14 0.49 1.23 8.95 2.40 4.95 10 13 3.50 1.27 Typ Max Min 4.60 2.72 0.88 1.70 0.70 1.32 9.35 2.70 5.15 10.40 14 3.93 1.40 0.173 0.094 0.024 0.044 0.019 0.048 0.352 0.094 0.194 0.393 0.511 0.137 0.050 Typ Max 0.181 0.107 0.034 0.066 0.027 0.052 0.368 0.106 0.202 0.410 0.551 0.154 0.055 13/20 Package mechanical data STB4NK60Zx, STD4NK60Zx, STP4NK60Z, STP4NK60ZFP D²PAK (TO-263) mechanical data mm inch Dim Min A A1 b b2 c c2 D D1 E E1 e e1 H J1 L L1 L2 R V2 4.40 0.03 0.70 1.14 0.45 1.23 8.95 7.50 10 8.50 Max Min 4.60 0.23 0.93 1.70 0.60 1.36 9.35 0.173 0.001 0.027 0.045 0.017 0.048 0.352 0.295 0.394 0.334 10.40 2.54 4.88 15 2.49 2.29 1.27 1.30 Typ Max 0.181 0.009 0.037 0.067 0.024 0.053 0.368 0.409 0.1 5.28 15.85 2.69 2.79 1.40 1.75 0.192 0.590 0.099 0.090 0.05 0.051 8° 0° 0.4 0° 0079457_M 14/20 Typ 0.208 0.624 0.106 0.110 0.055 0.069 0.016 8° STB4NK60Zx, STD4NK60Zx, STP4NK60Z, STP4NK60ZFP Package mechanical data TO-251 (IPAK) mechanical data mm. DIM. min. typ max. A 2.20 2.40 A1 0.90 1.10 b 0.64 0.90 b2 0.95 b4 5.20 5.40 c 0.45 0.60 c2 0.48 0.60 D 6.00 6.20 E 6.40 6.60 e e1 2.28 4.40 H 4.60 16.10 L 9.00 9.40 (L1) 0.80 1.20 L2 0.80 V1 10 o 0068771_H 15/20 Package mechanical data STB4NK60Zx, STD4NK60Zx, STP4NK60Z, STP4NK60ZFP TO-252 (DPAK) mechanical data DIM. mm. min. typ max. A 2.20 2.40 A1 0.90 1.10 A2 0.03 0.23 b 0.64 0.90 b4 5.20 5.40 c 0.45 0.60 c2 0.48 0.60 D 6.00 D1 E 6.20 5.10 6.40 E1 6.60 4.70 e 2.28 e1 4.40 4.60 H 9.35 10.10 L 1 L1 2.80 L2 L4 0.80 0.60 R V2 1 0.20 0o 8o 0068772_G 16/20 STB4NK60Zx, STD4NK60Zx, STP4NK60Z, STP4NK60ZFP 5 Packaging mechanical data Packaging mechanical data D2PAK FOOTPRINT TAPE AND REEL SHIPMENT REEL MECHANICAL DATA DIM. mm MIN. A B DIM. mm inch MIN. MAX. MIN. A0 10.5 10.7 0.413 0.421 B0 15.7 15.9 0.618 0.626 D 1.5 1.6 0.059 0.063 D1 1.59 1.61 0.062 0.063 E 1.65 1.85 0.065 0.073 F 11.4 11.6 0.449 0.456 K0 4.8 5.0 0.189 0.197 0.153 0.161 MAX. MIN. 330 1.5 C 12.8 D 20.2 G 24.4 N 100 T TAPE MECHANICAL DATA inch MAX. 12.992 0.059 13.2 0.504 0.520 26.4 0.960 1.039 0795 3.937 30.4 1.197 BASE QTY BULK QTY 1000 1000 MAX. P0 3.9 4.1 P1 11.9 12.1 0.468 0.476 P2 1.9 2.1 0.075 0.082 R 50 T 0.25 0.35 0.0098 0.0137 W 23.7 24.3 1.574 0.933 0.956 * on sales type 17/20 Packaging mechanical data STB4NK60Zx, STD4NK60Zx, STP4NK60Z, STP4NK60ZFP DPAK FOOTPRINT All dimensions are in millimeters TAPE AND REEL SHIPMENT REEL MECHANICAL DATA DIM. mm MIN. A B 1.5 C 12.8 D 20.2 G 16.4 N 50 T TAPE MECHANICAL DATA DIM. mm MIN. MAX. A0 6.8 7 0.267 0.275 B0 10.4 10.6 0.409 0.417 B1 D 18/20 inch 1.5 MIN. MAX. 12.1 0.476 1.6 0.059 0.063 D1 1.5 E 1.65 1.85 0.065 0.073 F 7.4 7.6 0.291 0.299 K0 2.55 2.75 0.100 0.108 P0 3.9 4.1 0.153 0.161 P1 7.9 8.1 0.311 0.319 P2 1.9 2.1 0.075 0.082 R 40 W 15.7 0.059 1.574 16.3 0.618 0.641 inch MAX. MIN. MAX. 330 12.992 13.2 0.504 0.520 18.4 0.645 0.724 0.059 0.795 1.968 22.4 0.881 BASE QTY BULK QTY 2500 2500 STB4NK60Zx, STD4NK60Zx, STP4NK60Z, STP4NK60ZFP 6 Revision history Revision history Table 9. Document revision history Date Revision Changes 25-Oct-2006 4 Document reformatted no content change 04-Mar-2008 5 Modified TO-220 and TO-220FP mechanical data 16-Apr-2008 6 Minor text changes to improve readability 19/20 STB4NK60Zx, STD4NK60Zx, STP4NK60Z, STP4NK60ZFP Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2008 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 20/20