Pressure Freescale Semiconductor + MPXV7002 Rev 2, 1/2009 Integrated Silicon Pressure Sensor On-Chip Signal Conditioned, Temperature Compensated and Calibrated MPXV7002 Series -2 to 2 kPa (-0.3 to 0.3 psi) 0.5 to 4.5 V Output The MPXV7002 series piezoresistive transducers are state-of-the-art monolithic silicon pressure sensors designed for a wide range of applications, but particularly those employing a microcontroller or microprocessor with A/D inputs. This transducer combines advanced micromachining techniques, thinfilm metallization, and bipolar processing to provide an accurate, high level analog output signal that is proportional to the applied pressure. Application Examples • • • • Features • • • • • • • Hospital Beds HVAC Respiratory Systems Process Control 2.5% Typical Error over +10°C to +60°C with Auto Zero 6.25% Maximum Error over +10°C to +60°C without Auto Zero Ideally Suited for Microprocessor or Microcontroller-Based Systems Thermoplastic (PPS) Surface Mount Package Temperature Compensated over +10° to +60°C Patented Silicon Shear Stress Strain Gauge Available in Differential and Gauge Configurations ORDERING INFORMATION Package Case Device Name No. Options Small Outline Package (MPXV7002 Series) MPXV7002GC6U Rails 482A MPXV7002GC6T1 Tape & Reel 482A MPXV7002GP Trays 1369 MPXV7002DP Trays 1351 None # of Ports Single Dual Gauge • • • Pressure Type Differential Absolute MPXV7002G • • • • MPXV7002G MPXV7002G • SMALL OUTLINE PACKAGE MPXV7002GC6U/C6T1 CASE 482A-01 MPXV7002GP CASE 1369-01 © Freescale Semiconductor, Inc., 2005, 2009. All rights reserved. Device Marking MPXV7002DP CASE 1351-01 MPXV7002DP Pressure Operating Characteristics Table 1. Operating Characteristics (VS = 5.0 Vdc, TA = 25°C unless otherwise noted. Decoupling circuit shown in Figure 3 required to meet specification.) Characteristic Pressure Range(1) Supply Voltage (2) Supply Current Symbol Min Typ Max Unit POP –2.0 — 2.0 kPa VS 4.75 5.0 5.25 Vdc Io — — 10 mAdc Pressure Offset(3) @ VS = 5.0 Volts (10 to 60°C) Voff 2.25 2.5 2.75 Vdc Full Scale Output(4) @ VS = 5.0 Volts (10 to 60°C) VFSO 4.25 4.5 4.75 Vdc Full Scale Span(5) @ VS = 5.0 Volts (10 to 60°C) VFSS 3.5 4.0 4.5 V Vdc Accuracy(6) (10 to 60°C) — — ±2.5(7) ±6.25 %VFSS V/P — 1.0 —- V/kPa Response Time(8) tR — 1.0 —- ms Output Source Current at Full Scale Output IO+ — 0.1 —- mAdc — — 20 —- ms Sensitivity Warm-Up Time (9) 1. 1.0 kPa (kiloPascal) equals 0.145 psi. 2. Device is ratiometric within this specified excitation range. 3. Offset (Voff) is defined as the output voltage at the minimum rated pressure. 4. Full Scale Output (VFSO) is defined as the output voltage at the maximum or full rated pressure. 5. Full Scale Span (VFSS) is defined as the algebraic difference between the output voltage at full rated pressure and the output voltage at the minimum rated pressure. 6. Accuracy (error budget) consists of the following: Linearity: Temperature Hysteresis: Pressure Hysteresis: TcSpan: TcOffset: Variation from Nominal: Output deviation from a straight line relationship with pressure over the specified pressure range. Output deviation at any temperature within the operating temperature range, after the temperature is cycled to and from the minimum or maximum operating temperature points, with zero differential pressure applied. Output deviation at any pressure within the specified range, when this pressure is cycled to and from the minimum or maximum rated pressure, at 25°C. Output deviation over the temperature range of 10° to 60°C, relative to 25°C. Output deviation with minimum rated pressure applied, over the temperature range of 10° to 60°C, relative to 25°C. The variation from nominal values, for Offset or Full Scale Span, as a percent of VFSS, at 25°C. 7. Auto Zero at Factory Installation: Due to the sensitivity of the MPXV7002 Series, external mechanical stresses and mounting position can affect the zero pressure output reading. Auto zero is defined as storing the zero pressure output reading and subtracting this from the device's output during normal operations. Reference AN1636 for specific information. The specified accuracy assumes a maximum temperature change of ± 5°C between auto zero and measurement. 8. Response Time is defined as the time for the incremental change in the output to go from 10% to 90% of its final value when subjected to a specified step change in pressure. 9. Warm-up Time is defined as the time required for the product to meet the specified output voltage after the Pressure has been stabilized. MPXV7002 2 Sensors Freescale Semiconductor Pressure Maximum Ratings Table 2. Maximum Ratings(1) Rating Symbol Value Unit Maximum Pressure (P1 > P2) Pmax 75 kPa Storage Temperature Tstg –30 to +100 °C Operating Temperature TA 10 to 60 °C 1. Exposure beyond the specified limits may cause permanent damage or degradation to the device. Figure 1 shows a block diagram of the internal circuitry integrated on a pressure sensor chip. VS 2 Thin Film Temperature Compensation and Gain Stage #1 Sensing Element GND Gain Stage #2 and Ground Reference Shift Circuitry Vout 4 Pins 1, 5, 6, 7, and 8 are NO CONNECTS for Small Outline Package Device 3 Figure 1. Integrated Pressure Sensor Schematic MPXV7002 Sensors Freescale Semiconductor 3 Pressure ON-CHIP TEMPERATURE COMPENSATION, CALIBRATION AND SIGNAL CONDITIONING The performance over temperature is achieved by integrating the shear-stress strain gauge, temperature compensation, calibration and signal conditioning circuitry onto a single monolithic chip. Figure 2 illustrates the Differential or Gauge configuration in the basic chip carrier (Case 482). A gel die coat isolates the die surface and wire bonds from the environment, while allowing the pressure signal to be transmitted to the sensor diaphragm. The MPXV7002 series pressure sensor operating characteristics, and internal reliability and qualification tests are based on use of dry air as the pressure media. Media, other than dry air, may have adverse effects on sensor performance and long-term reliability. Contact the factory for information regarding media compatibility in your application. Figure 3 shows the recommended decoupling circuit for interfacing the integrated sensor to the A/D input of a microprocessor or microcontroller. Proper decoupling of the power supply is recommended. Figure 4 shows the sensor output signal relative to pressure input. Typical, minimum, and maximum output curves are shown for operation over a temperature range of 10° to 60°C using the decoupling circuit shown in Figure 3. The output will saturate outside of the specified pressure range. Fluoro Silicone Gel Die Coat Die Stainless Steel Cap P1 Thermoplastic Case Wire Bond Lead Frame P2 Die Bond Differential Sensing Element Figure 2. Cross-Sectional Diagram SOP (not to scale) +5 V Vout OUTPUT Vs IPS 1.0 µF 0.01 µF GND 470 pF Figure 3. Recommended Power Supply Decoupling and Output Filtering (For additional output filtering, please refer to Application Note AN1646.) MPXV7002 4 Sensors Freescale Semiconductor Pressure 5.0 Transfer Function: Vout = VS × (0.2 × P(kPa)+0.5) ± 6.25% VFSS VS = 5.0 Vdc TA = 10 to 60°C Output Voltage (V) 4.0 3.0 TYPICAL MAX 2.0 MIN 1.0 0 -2 -1 0 1 2 Differential Pressure (kPa) Figure 4. Output versus Pressure Differential PRESSURE (P1)/VACUUM (P2) SIDE IDENTIFICATION TABLE Freescale designates the two sides of the pressure sensor as the Pressure (P1) side and the Vacuum (P2) side. The Pressure (P1) side is the side containing a gel die coat which protects the die from harsh media. Part Number The Pressure (P1) side may be identified by using the following table: Pressure (P1) Side Identifier Case Type MPXV7002GC6U/GC6T1 482A-01 Side with Port Attached MPXV7002GP 1369-01 Side with Port Attached MPXV7002DP 1351-01 Side with Part Marking MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS Surface mount board layout is a critical portion of the total design. The footprint for the surface mount packages must be the correct size to ensure proper solder connection interface between the board and the package. With the correct footprint, the packages will self align when subjected to a solder reflow process. It is always recommended to design boards with a solder mask layer to avoid bridging and shorting between solder pads. 0.100 TYP 8X 2.54 0.660 16.76 0.060 TYP 8X 1.52 0.300 7.62 0.100 TYP 8X 2.54 inch mm SCALE 2:1 Figure 5. Small Outline Package Footprint MPXV7002 Sensors Freescale Semiconductor 5 Pressure PACKAGE DIMENSIONS -A- D 4 0.25 (0.010) 5 N 8 PL M T B S A S NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006). 5. ALL VERTICAL SURFACES 5˚ TYPICAL DRAFT. -BG 8 1 S W V C H J -TK M PIN 1 IDENTIFIER DIM A B C D G H J K M N S V W INCHES MIN MAX 0.415 0.425 0.415 0.425 0.500 0.520 0.038 0.042 0.100 BSC 0.002 0.010 0.009 0.011 0.061 0.071 0˚ 7˚ 0.444 0.448 0.709 0.725 0.245 0.255 0.115 0.125 MILLIMETERS MIN MAX 10.54 10.79 10.54 10.79 12.70 13.21 0.96 1.07 2.54 BSC 0.05 0.25 0.23 0.28 1.55 1.80 0˚ 7˚ 11.28 11.38 18.01 18.41 6.22 6.48 2.92 3.17 SEATING PLANE CASE 482A-01 ISSUE A SMALL OUTLINE PACKAGE MPXV7002 6 Sensors Freescale Semiconductor Pressure PACKAGE DIMENSIONS CASE 1351-01 ISSUE A SMALL OUTLINE PACKAGE MPXV7002 Sensors Freescale Semiconductor 7 Pressure PACKAGE DIMENSIONS MPXV7002 8 Sensors Freescale Semiconductor Pressure PACKAGE DIMENSIONS CASE 1369-01 ISSUE B SMALL OUTLINE PACKAGE MPXV7002 Sensors Freescale Semiconductor 9 Pressure PACKAGE DIMENSIONS CASE 1369-01 ISSUE B SMALL OUTLINE PACKAGE MPXV7002 10 Sensors Freescale Semiconductor How to Reach Us: Home Page: www.freescale.com Web Support: http://www.freescale.com/support USA/Europe or Locations Not Listed: Freescale Semiconductor, Inc. Technical Information Center, EL516 2100 East Elliot Road Tempe, Arizona 85284 1-800-521-6274 or +1-480-768-2130 www.freescale.com/support Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) www.freescale.com/support Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku, Tokyo 153-0064 Japan 0120 191014 or +81 3 5437 9125 [email protected] Asia/Pacific: Freescale Semiconductor China Ltd. Exchange Building 23F No. 118 Jianguo Road Chaoyang District Beijing 100022 China +86 010 5879 8000 [email protected] For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 1-800-441-2447 or +1-303-675-2140 Fax: +1-303-675-2150 [email protected] MPXV7002 Rev. 2 1/2009 Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”, must be validated for each customer application by customer’s technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. © Freescale Semiconductor, Inc. 2009. All rights reserved.