VISHAY GBPC6005

GBPC6005 THRU GBPC610
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
Reverse Voltage - 50 to 1000 Volts
Forward Current - 6.0 Amperes
Case Style GBPC
FEATURES
0.630 (16.00)
0.590 (14.98)
0.445 (11.30)
0.405 (10.29)
HOLE FOR
#6 SCREW
0.158 (4.01)
AC
0.142 (3.61)
DIA.
0.445 (11.30)
0.405 (10.29)
0.630 (16.00)
0.590 (14.98)
AC
0.094 (2.4) x 45 degrees
0.128 (3.25)
0.048 (1.22)
0.040 (1.02) TYP.
0.750
(19.05)
MIN.
0.042(1.07)
0.038(0.96)
DIA.
0.200 (5.08)
0.160 (4.06)
Polarity shown on side of case: Positive lead by beveled corner
♦ Plastic package has carries Underwriters Laboratory
Flammability Classification 94V-0
♦ This series is UL listed under recognized under Component
Index, file number E54214
♦ Glass passivated chip junctions
♦ High case dielectric strength of 1500 VRMS
♦ Typical IR less than 0.5µA
♦ High forward surge current capability
♦ Ideal for printed circuit boards
♦ High temperature soldering guaranteed:
260°C/10 seconds at 5lbs. (2.3 kg) tension
MECHANICAL DATA
Case: Molded plastic body over passivated junction
Terminals: Plated leads solderable per MIL-STD-750,
Method 2026
Mounting Position: Any (NOTE 1)
Mounting Torque: 5.0 in. - lb. max.
Weight: 0.1 ounce, 2.8 grams
Dimensions in inches and (millimeters)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25°C ambient temperature unless otherwise specified.
SYMBOLS
GBPC
6005
GBPC
601
GBPC
602
GBPC
604
GBPC
606
GBPC
608
GBPC
610 UNITS
Maximum repetitive peak reverse voltage
VRRM
50
100
200
400
600
800
1000 Volts
Maximum RMS bridge input voltage
VRMS
35
70
140
280
420
560
700
VDC
50
100
200
400
600
800
1000 Volts
Maximum DC blocking voltage
I(AV)
6.0
3.0
Amps
IFSM
175.0
Amps
Rating for fusing (t<8.3ms)
I2t
127.0
A2sec
Maximum instantaneous forward voltage drop
per leg at 3.0 Amperes
VF
1.0
Volts
Maximum DC reverse current at rated
DC blocking voltage per leg
IR
5.0
500.0
µA
Maximum average forward
rectified output current at
TC=50°C (NOTE1, 2)
TA=40°C (NOTE 3)
Volts
Peak forward surge current single sine-wave
superimposed on rated load (JEDEC Method)
TA=25°C
TA=125°C
Typical junction capacitance per leg (NOTE 4)
Typical thermal resistance per leg (NOTE 3)
(NOTE 2)
Operating junction temperature range
Storage temperature range
CJ
186.0
90.0
RΘJA
RΘJC
22.0
7.3
°C/W
TJ
-55 to +150
°C
TSTG
-55 to +150
°C
NOTES:
(1) Bolt down on heat-sink with silicone thermal compound between bridge and mounting surface for maximum heat transfer with #6 screw
(2) Unit mounted on 5.5 x 6.0 x 0.11" thick (14 x 15 x 0.3cm) Al. Plate
(3) Unit mounted on P.C.B. at 0.375" (9.5mm) lead length with 0.5 x 0.5" (12 x 12mm) copper pads
(4) Measured at 1 MHz and applied reverse voltage of 4.0 Volts
4/98
pF
RATINGS AND CHARACTERISTICS CURVES GBPC6005 THRU GBPC610
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD
SURGE CURRENT PER LEG
8.0
5.5 x 6.0 x 0.11” THK
(14 x 1.5” x 0.3cm)
AL. PLATE
CASE TEMPERATURE, TC
HEAT-SINK MOUNTING,
6.0
60 HZ RESISTIVE OR
INDUCTIVE LOAD
4.0
2.0 AMBIENT TEMPERATURE, TA
P.C.B. MOUNTING,
0.375” (9.5mm) LEAD LENGTH
0
0
50
100
150
200
PEAK FORWARD SURGE CURRENT,
AMPERES
AVERAGE FORWARD OUTPUT CURRENT,
AMPERES
FIG. 1 - DERATING CURVE OUTPUT RECTIFIED
CURRENT
TJ=TJ max.
SINGLE HALF SINE-WAVE
(JEDEC Method)
175
150
125
100
75
1.0 CYCLE
50
1
10
100
NUMBER OF CYCLES AT 60 Hz
TEMPERATURE, °C
FIG. 4 - TYPICAL FORWARD
CHARACTERISTICS PER LEG
FIG. 3 - TYPICAL REVERSE LEAKAGE
CHARACTERISTICS PER LEG
100
500
TJ=25°C
PULSE WIDTH=300µs
1% DUTY CYCLE
10
1
0.1
0.01
0.4
0.6
0.8
1.0
1.2
1.4
1.6
100
INSTANTANEOUS REVERSE CURRENT,
MICROAMPERES
INSTANTANEOUS FORWARD CURRENT,
AMPERES
TA=125°C
TJ=100°C
10
1
TJ=25°C
0.1
1.8
0
INSTANTANEOUS FORWARD VOLTAGE,
VOLTS
TJ=25°C
f=1.0 MHz
Vsig=50mVp-p
100
50 - 400V
600 - 1000V
10
REVERSE VOLTAGE, VOLTS
100
TRANSIENT THERMAL IMPEDANCE,
°C/W
JUNCTION CAPACITANCE, pF
1,000
1
40
60
80
100
PERCENT OF RATED PEAK REVERSE
VOLTAGE, %
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
PER LEG
10
0.1
20
FIG. 6 - TYPICAL TRANSIENT THERMAL
IMPEDANCE
100
10
1
0.1
0.01
0.1
1
t, HEATING TIME, sec.
10
100