MITSUBISHI <INTELLIGENT POWER MODULES> PM200RLA060 FLAT-BASE TYPE INSULATED PACKAGE PM200RLA060 FEATURE a) Adopting new 5th generation IGBT (CSTBT) chip, which performance is improved by 1µm fine rule process. For example, typical Vce(sat)=1.5V @Tj=125°C b) I adopt the over-temperature conservation by Tj detection of CSTBT chip, and error output is possible from all each conservation upper and lower arm of IPM. c) Current rating of brake part increased. 50% for the current rating of inverter part. • 3φ 200A, 600V Current-sense IGBT type inverter • 100A, 600V Current-sense regenerative brake IGBT • Monolithic gate drive & protection logic • Detection, protection & status indication circuits for, shortcircuit, over-temperature & under-voltage (P-Fo available from upper arm devices) • Acoustic noise-less 22kW class inverter application • UL Recognized Yellow Card No.E80276(N) File No.E80271 APPLICATION General purpose inverter, servo drives and other motor controls PACKAGE OUTLINES Dimensions in mm 135 6.05 6.05 110±0.5 6-M5 Nuts 26 26 10.5 10.5 40.5 11.7 10.5 13(Screwing Depth) 13 18.7 U 3-2 10.5 3-2 10 3-2 10 3.25 20 10 19- 5 0.5 1 30.15 6.05 9 11 4 Terminal code L A B E L 34.7 2-φ2.5 13 33.6 4-φ5.5 Mounting Holes 19 24.1 +1 -0.5 11 16.5 10.5 6-2 P 66.5 3.25 78±0.5 20 N 71.5 110 10.5 B V 21.5 18 W 6.05 13 6 6 1. 2. 3. 4. 5. VUPC 6. UFO 7. UP 8. VUP1 9. VVPC 10. VFO VP VVP1 VWPC WFO 11. 12. 13. 14. 15. WP VWP1 VNC VN1 Br 16. 17. 18. 19. UN VN WN Fo May 2005 MITSUBISHI <INTELLIGENT POWER MODULES> PM200RLA060 FLAT-BASE TYPE INSULATED PACKAGE INTERNAL FUNCTIONS BLOCK DIAGRAM Br Fo VNC WN VN1 WP VWP1 VWPC WFO UN VN 1.5k Gnd In Gnd 1.5k Fo Vcc Si Out VP VVPC OT Gnd In Gnd Fo Vcc Si Out OT Gnd In Gnd B Fo Vcc Si Out OT Gnd In Gnd Fo Vcc Si Out OT N Gnd In Gnd UP VUPC VUP1 UFO 1.5k Fo Vcc Si Out VVP1 VFO OT Gnd In Gnd W V 1.5k Fo Vcc Si Out Gnd In OT Gnd Fo Vcc Si Out U OT P MAXIMUM RATINGS (Tj = 25°C, unless otherwise noted) INVERTER PART Symbol VCES ±IC ±ICP PC Tj Parameter Collector-Emitter Voltage Collector Current Collector Current (Peak) Collector Dissipation Junction Temperature Condition VD = 15V, VCIN = 15V TC = 25°C TC = 25°C TC = 25°C (Note-1) Ratings 600 200 400 781 –20 ~ +150 Unit V A A W °C Ratings 600 100 200 446 600 100 –20 ~ +150 Unit V A A W V A °C Ratings Unit 20 V 20 V 20 V 20 mA BRAKE PART Symbol VCES IC ICP PC VR(DC) IF Tj Parameter Collector-Emitter Voltage Collector Current Collector Current (Peak) Collector Dissipation FWDi Rated DC Reverse Voltage FWDi Forward Current Junction Temperature Condition VD = 15V, VCIN = 15V TC = 25°C TC = 25°C TC = 25°C TC = 25°C TC = 25°C (Note-1) CONTROL PART Symbol Parameter VD Supply Voltage VCIN Input Voltage VFO Fault Output Supply Voltage IFO Fault Output Current Condition Applied between : VUP1-VUPC VVP1-VVPC, VWP1-VWPC, VN1-VNC Applied between : UP-VUPC, VP-VVPC WP-VWPC, UN • VN • WN • Br-VNC Applied between : UFO-VUPC, VFO-VVPC, WFO-VWPC FO-VNC Sink current at UFO, VFO, WFO, FO terminals May 2005 MITSUBISHI <INTELLIGENT POWER MODULES> PM200RLA060 FLAT-BASE TYPE INSULATED PACKAGE TOTAL SYSTEM Symbol Parameter Supply Voltage Protected by VCC(PROT) SC VCC(surge) Supply Voltage (Surge) Storage Temperature Tstg Isolation Voltage Viso Ratings Condition VD = 13.5 ~ 16.5V, Inverter Part, Tj = +125°C Start Applied between : P-N, Surge value 60Hz, Sinusoidal, Charged part to Base, AC 1 min. Unit 400 V 500 –40 ~ +125 2500 V °C Vrms THERMAL RESISTANCES Symbol Condition Parameter Rth(j-c)Q Rth(j-c)F Rth(j-c)Q Rth(j-c)F Junction to case Thermal Resistances Rth(c-f) Contact Thermal Resistance Inverter IGBT (per 1 element) Inverter FWDi (per 1 element) Brake IGBT Brake FWDi Case to fin, (per 1 module) Thermal grease applied (Note-1) (Note-1) (Note-1) (Note-1) (Note-1) Min. — — — — Limits Typ. — — — — Max. 0.16* 0.25* 0.28* 0.44* — — 0.023 Unit °C/W * If you use this value, Rth(f-a) should be measured just under the chips. (Note-1) Tc (under the chip) measurement point is below. arm axis X Y UP IGBT FWDi 23.7 23.0 56.7 43.7 VP IGBT FWDi 57.2 56.5 56.7 43.7 Unit : mm WP IGBT FWDi 87.7 86.5 56.7 43.7 UN IGBT FWDi 37.7 38.0 28.7 41.8 VN IGBT FWDi 70.2 71.5 28.7 41.8 WN IGBT FWDi 100.7 101.5 28.7 41.8 Br IGBT 11.0 26.7 FWDi 7.7 60.9 Bottom view Y X ELECTRICAL CHARACTERISTICS (Tj = 25°C, unless otherwise noted) INVERTER PART Symbol VCE(sat) VEC ton trr tc(on) toff tc(off) ICES Parameter Condition Collector-Emitter Saturation Voltage FWDi Forward Voltage VD = 15V, IC = 200A VCIN = 0V (Fig. 1) –IC = 200A, VD = 15V, VCIN = 15V Switching Time VD = 15V, VCIN = 0V↔15V VCC = 300V, IC = 200A Tj = 125°C Inductive Load Collector-Emitter Cutoff Current VCE = VCES, VCIN = 15V Tj = 25°C Tj = 125°C (Fig. 2) (Fig. 3, 4) (Fig. 5) Tj = 25°C Tj = 125°C Min. — — — 0.5 — — — — — — Limits Typ. 1.6 1.5 2.2 1.0 0.2 0.4 1.2 0.5 — — Max. 2.1 2.0 3.3 2.4 0.4 1.0 2.5 1.0 1 10 Unit V V µs mA May 2005 MITSUBISHI <INTELLIGENT POWER MODULES> PM200RLA060 FLAT-BASE TYPE INSULATED PACKAGE BRAKE PART Symbol VCE(sat) VFM ICES Condition Parameter Collector-Emitter Saturation Voltage FWDi Forward Voltage Collector-Emitter Cutoff Current VD = 15V, IC = 100A VCIN = 0V IF = 100A (Fig. 1) VCE = VCES, VCIN = 15V (Fig. 5) Tj = 25°C Tj = 125°C (Fig. 2) Tj = 25°C Tj = 125°C Min. — — — — — Limits Typ. 1.6 1.5 2.2 — — Max. 2.1 2.0 3.3 1 10 Min. — — 1.2 1.7 400 200 Limits Typ. 24 6 1.5 2.0 — — Max. 34 12 1.8 2.3 — — Unit V V mA CONTROL PART Symbol Parameter Condition VN1-VNC V*P1-V*PC ID Circuit Current VD = 15V, VCIN = 15V Vth(ON) Vth(OFF) Input ON Threshold Voltage Input OFF Threshold Voltage SC Short Circuit Trip Level Applied between : UP-VUPC, VP-VVPC, WP-VWPC UN • VN • WN • Br-VNC Inverter part –20 ≤ Tj ≤ 125°C, VD = 15V (Fig. 3,6) Brake part toff(SC) Short Circuit Current Delay Time VD = 15V Over Temperature Protection VD = 15V Detect Tj of IGBT chip Supply Circuit Under-Voltage Protection –20 ≤ Tj ≤ 125°C Fault Output Current VD = 15V, VFO = 15V (Note-2) Minimum Fault Output Pulse Width VD = 15V (Note-2) OT OTr UV UVr IFO(H) IFO(L) tFO (Fig. 3,6) Trip level Reset level Trip level Reset level Unit mA V A — 0.2 — µs 135 — 11.5 — — — 145 125 12.0 12.5 — 10 — — 12.5 — 0.01 15 °C 1.0 1.8 — V mA ms (Note-2) Fault output is given only when the internal SC, OT & UV protections schemes of either upper or lower arm device operate to protect it. MECHANICAL RATINGS AND CHARACTERISTICS Symbol — — — Condition Parameter Mounting torque Mounting torque Weight Main terminal Mounting part screw : M5 screw : M5 — Min. 2.5 2.5 — Limits Typ. 3.0 3.0 800 Max. 3.5 3.5 — Unit N•m N•m g RECOMMENDED CONDITIONS FOR USE Symbol VCC Parameter Supply Voltage VD Control Supply Voltage VCIN(ON) VCIN(OFF) fPWM Input ON Voltage Input OFF Voltage PWM Input Frequency Arm Shoot-through Blocking Time tdead Condition Applied across P-N terminals Applied between : VUP1-VUPC, VVP1-VVPC VWP1-VWPC, VN1-VNC (Note-3) Applied between : UP-VUPC, VP-VVPC, WP-VWPC UN • VN • WN • Br-VNC Using Application Circuit of Fig. 8 For IPM’s each input signals Recommended value ≤ 400 Unit V 15 ± 1.5 V (Fig. 7) ≤ 0.8 ≥ 9.0 ≤ 20 kHz ≥ 2.0 µs V (Note-3) With ripple satisfying the following conditions: dv/dt swing ≤ ±5V/µs, Variation ≤ 2V peak to peak May 2005 MITSUBISHI <INTELLIGENT POWER MODULES> PM200RLA060 FLAT-BASE TYPE INSULATED PACKAGE PRECAUTIONS FOR TESTING 1. Before appling any control supply voltage (VD), the input terminals should be pulled up by resistores, etc. to their corresponding supply voltage and each input signal should be kept off state. After this, the specified ON and OFF level setting for each input signal should be done. 2. When performing “SC” tests, the turn-off surge voltage spike at the corresponding protection operation should not be allowed to rise above VCES rating of the device. (These test should not be done by using a curve tracer or its equivalent.) P, (U,V,W,B) IN Fo VCIN P, (U,V,W) Ic V IN Fo VCIN –Ic V (15V) (0V) U,V,W, (N) VD (all) U,V,W,B, (N) VD (all) Fig. 1 VCE(sat) Test Fig. 2 VEC, (VFM) Test a) Lower Arm Switching P VCIN (15V) Fo Signal input (Upper Arm) trr CS Ic Vcc Fo Signal input (Lower Arm) VCIN VCE Irr U,V,W 90% 90% N VD (all) b) Upper Arm Switching Ic 10% 10% 10% 10% P tc(on) Fo Signal input (Upper Arm) VCIN VCIN U,V,W CS VCIN (15V) tc(off) Vcc td(on) tr tf td(off) Fo Signal input (Lower Arm) (ton= td(on) + tr) (toff= td(off) + tf) N Ic VD (all) Fig. 3 Switching time and SC test circuit Fig. 4 Switching time test waveform VCIN Short Circuit Current P, (U,V,W,B) A VCIN (15V) Constant Current IN Fo SC Pulse VCE Ic VD (all) U,V,W, (N) Fo toff(SC) Fig. 5 ICES Test Fig. 6 SC test waveform IPM’ input signal VCIN (Upper Arm) 1.5V 0V IPM’ input signal VCIN (Lower Arm) 0V 2V tdead 2V 1.5V 1.5V tdead 2V t t tdead 1.5V: Input on threshold voltage Vth(on) typical value, 2V: Input off threshold voltage Vth(off) typical value Fig. 7 Dead time measurement point example May 2005 MITSUBISHI <INTELLIGENT POWER MODULES> PM200RLA060 FLAT-BASE TYPE INSULATED PACKAGE P ≥10µ 20k VUP1 → VD UFo IF 1.5k Vcc Fo UP OT OUT In VUPC + – Si U GND GND ≥0.1µ VVP1 VFo VD 1.5k Fo VP 1.5k Vcc Fo WP M OT OUT Si W GND GND 20k Vcc ≥10µ IF V In VWPC → Si GND GND VWP1 VD OT OUT In VVPC WFo Vcc Fo UN OT OUT Si In GND GND ≥0.1µ N OT 20k → Vcc ≥10µ IF Fo VN OUT Si In GND GND ≥0.1µ 20k → VD Vcc ≥10µ IF Fo WN ≥0.1µ In IF Vcc Fo Br 1k Fo OT OUT Si GND GND VNC 4.7k → 5V VN1 In 1.5k B OT OUT Si GND GND : Interface which is the same as the U-phase Fig. 8 Application Example Circuit NOTES FOR STABLE AND SAFE OPERATION ; Design the PCB pattern to minimize wiring length between opto-coupler and IPM’s input terminal, and also to minimize the stray capacity between the input and output wirings of opto-coupler. Connect low impedance capacitor between the Vcc and GND terminal of each fast switching opto-coupler. Fast switching opto-couplers: tPLH, tPHL ≤ 0.8µs, Use High CMR type. Slow switching opto-coupler: CTR > 100% Use 4 isolated control power supplies (VD). Also, care should be taken to minimize the instantaneous voltage charge of the power supply. Make inductance of DC bus line as small as possible, and minimize surge voltage using snubber capacitor between P and N terminal. Use line noise filter capacitor (ex. 4.7nF) between each input AC line and ground to reject common-mode noise from AC line and improve noise immunity of the system. • • • • • • • May 2005 MITSUBISHI <INTELLIGENT POWER MODULES> PM200RLA060 FLAT-BASE TYPE INSULATED PACKAGE PERFORMANCE CURVES COLLECTOR-EMITTER SATURATION VOLTAGE (VS. Ic) CHARACTERISTICS (INVERTER PART · TYPICAL) OUTPUT CHARACTERISTICS (INVERTER PART · TYPICAL) 13V 160 120 80 40 0 0.5 1 1.5 2 2 VD = 15V 1.5 1 0.5 Tj = 25°C Tj = 125°C 0 40 0 80 120 160 200 240 COLLECTOR-EMITTER VOLTAGE VCE (V) COLLECTOR CURRENT IC (A) COLLECTOR-EMITTER SATURATION VOLTAGE (VS. VD) CHARACTERISTICS (INVERTER PART · TYPICAL) 2 SWITCHING TIME CHARACTERISTICS (TYPICAL) 1.5 1 0.5 IC = 200A Tj = 25°C Tj = 125°C 0 12 101 7 5 4 3 2 13 14 15 16 17 101 SWITCHING TIME tc(on), tc(off) (µs) COLLECTOR-EMITTER SATURATION VOLTAGE VCE (sat) (V) VD = 17V 200 0 SWITCHING TIME ton, toff (µs) 15V 7 VCC = 300V 5 VD = 15V Tj = 25°C 4 Tj = 125°C 3 2 Inductive load 100 7 5 4 tc(on) 3 tc(off) tc(off) tc(on) 2 10–1 1 10 18 2 3 4 5 7 102 2 3 4 5 7 103 CONTROL SUPPLY VOLTAGE VD (V) COLLECTOR CURRENT IC (A) SWITCHING TIME CHARACTERISTICS (TYPICAL) SWITCHING LOSS CHARACTERISTICS (TYPICAL) VCC = 300V VD = 15V Tj = 25°C Tj = 125°C Inductive load toff toff ton 100 7 5 4 3 2 10–1 1 10 2 3 4 5 7 102 2 3 4 5 7 103 COLLECTOR CURRENT IC (A) SWITCHING LOSS ESW(on), ESW(off) (mJ/pulse) COLLECTOR CURRENT IC (A) Tj = 25°C COLLECTOR-EMITTER SATURATION VOLTAGE VCE (sat) (V) 240 102 7 5 4 3 2 ESW(off) ESW(on) 101 7 5 4 ESW(on), 3 ESW(off) 2 100 ESW(on) VCC = 300V VD = 15V Tj = 25°C Tj = 125°C Inductive load 7 5 4 3 ESW(off) 2 10–1 1 10 2 3 4 5 7 102 2 3 4 5 7 103 COLLECTOR CURRENT IC (A) May 2005 MITSUBISHI <INTELLIGENT POWER MODULES> PM200RLA060 103 VD = 15V 7 5 4 3 2 102 7 5 4 3 2 101 Tj = 25°C Tj = 125°C 0 0.5 1 1.5 2 5 4 3 5 4 3 2 2 trr 10–1 2 2 7 5 4 3 VCC = 300V VD = 15V Tj = 25°C 2 Tj = 125°C Inductive load 100 3 4 5 7 102 2 3 4 5 7 103 EMITTER-COLLECTOR VOLTAGE VEC (V) COLLECTOR RECOVERY CURRENT –IC (A) OUTPUT CHARACTERISTICS (BRAKE PART · TYPICAL) COLLECTOR-EMITTER SATURATION VOLTAGE (VS. Ic) CHARACTERISTICS (BRAKE PART · TYPICAL) COLLECTOR-EMITTER SATURATION VOLTAGE VCE (sat) (V) Tj = 25°C 15V VD = 17V 13V 100 50 0 0 0.5 1 1.5 2 2.5 2 VD = 15V 1.5 1 0.5 Tj = 25°C Tj = 125°C 0 0 2 1.5 1 0.5 IC = 100A Tj = 25°C Tj = 125°C 0 12 13 14 15 16 17 18 CONTROL SUPPLY VOLTAGE VD (V) COLLECTOR RECOVERY CURRENT –IC (A) COLLECTOR-EMITTER SATURATION VOLTAGE (VS. VD) CHARACTERISTICS (BRAKE PART · TYPICAL) 2.5 50 100 150 COLLECTOR CURRENT IC (A) COLLECTOR-EMITTER VOLTAGE VCE (V) COLLECTOR-EMITTER SATURATION VOLTAGE VCE (sat) (V) 101 trr 7 5 4 3 10–2 1 10 2.5 150 COLLECTOR CURRENT IC (A) DIODE REVERSE RECOVERY CHARACTERISTICS (INVERTER PART · TYPICAL) 100 102 Irr 7 7 Irr REVERSE RECOVERY CURRENT lrr (A) DIODE FORWARD CHARACTERISTICS (INVERTER PART · TYPICAL) REVERSE RECOVERY TIME trr (µs) COLLECTOR RECOVERY CURRENT –IC (A) FLAT-BASE TYPE INSULATED PACKAGE DIODE FORWARD CHARACTERISTICS (BRAKE PART · TYPICAL) 103 VD = 15V 7 5 4 3 2 102 7 5 4 3 2 101 7 5 4 3 2 100 Tj = 25°C Tj = 125°C 0 0.5 1 1.5 2 2.5 EMITTER-COLLECTOR VOLTAGE VEC (V) May 2005 MITSUBISHI <INTELLIGENT POWER MODULES> PM200RLA060 FLAT-BASE TYPE INSULATED PACKAGE TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (INVERTER PART) ID VS. fc CHARACTERISTICS (TYPICAL) 100 VD = 15V 60 Tj = 25°C N-side ID (mA) 50 40 30 20 P-side 10 0 0 5 10 15 20 25 fc (kHz) NORMALIZED TRANSIENT THERMAL IMPEDANCE Zth (j – c) 70 7 5 3 2 10–1 7 5 3 2 10–2 Single Pulse 7 5 IGBT Part; Per unit base = Rth(j – c)Q = 0.16°C/ W 3 FWDi Part; 2 Per unit base = Rth(j – c)F = 0.25°C/ W 10–3 –5 10 2 3 5 710–4 2 3 5 710–3 2 3 5 710–2 2 3 5 710–1 2 3 5 7100 2 3 5 7101 TIME (s) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (BRAKE PART) NORMALIZED TRANSIENT THERMAL IMPEDANCE Zth (j – c) 100 7 5 3 2 10–1 7 5 3 2 10–2 Single Pulse 7 5 IGBT Part; Per unit base = Rth(j – c)Q = 0.28°C/ W 3 FWDi Part; 2 Per unit base = Rth(j – c)F = 0.44°C/ W 10–3 –5 10 2 3 5 710–4 2 3 5 710–3 2 3 5 710–2 2 3 5 710–1 2 3 5 7100 2 3 5 7101 TIME (s) May 2005