GBPC1005 THRU GBPC110 GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER Reverse Voltage - 50 to 1000 Volts Forward Current - 3.0 Amperes Case Style GBPC1 FEATURES 0.630 (16.00) 0.590 (14.98) 0.445 (11.30) 0.405 (10.29) HOLE FOR #6 SCREW 0.158 (4.01) AC 0.142 (3.61) DIA. 0.445 (11.30) 0.405 (10.29) 0.630 (16.00) 0.590 (14.98) AC 0.094 (2.4) x 45 degrees 0.128 (3.25) 0.048 (1.22) 0.032 (0.81) 0.040 (1.02) TYP. DIA. 0.028 (0.71) ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ This series is UL listed under Recognized Component Index, file number E54214 ♦ Glass passivated chip junctions ♦ High case dielectric with standing voltage of 1500 VRMS ♦ Typical IR less than 0.1µA ♦ High surge current capability ♦ Ideal for printed circuit boards ♦ High temperature soldering guaranteed: 260°C/10 seconds, 0.375" (9.5mm) lead length, 5lbs. (2.3kg) tension 0.750 (19.05) MIN. MECHANICAL DATA 0.200 (5.08) 0.160 (4.06) Polarity shown on side of case: Positive lead by beveled corner Dimensions in inches and (millimeters) Case: Molded plastic body over passivated junctions Terminals: Plated leads solderable per MIL-STD-750, Method 2026 Mounting Position: Any (NOTE 1) Mounting Torque: 5.0 in. - lb. max. Weight: 0.1 ounce, 2.8 grams MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS GBPC 1005 GBPC 101 GBPC 102 GBPC 104 GBPC 106 GBPC 108 GBPC 110 UNITS Maximum repetitive peak reverse voltage VRRM 50 100 200 400 600 800 1000 Volts Maximum RMS bridge input voltage VRMS 35 70 140 280 420 560 700 Volts VDC 50 100 200 400 600 800 1000 Volts Maximum DC blocking voltage I(AV) 3.0 2.0 Amps IFSM 60.0 Amps Rating for fusing (t<8.3ms) I2t 15.0 A2sec Maximum instantaneous forward voltage drop per leg at 1.5 Amperes VF 1.0 Volts Maximum DC reverse current at rated DC blocking voltage per leg IR 5.0 500.0 µA CJ 21.0 pF RΘJA RΘJC 12.0 8.0 °C/W TJ, TSTG -55 to +150 °C Maximum average forward rectified output current at TC=60°C (NOTE 2) TA=25°C (NOTE 3) Peak forward surge current single sine-wave superimposed on rated load (JEDEC Method) TC=60°C TA= 25°C TA=125°C Typical junction capacitance per leg (NOTE 4) Typical thermal resistance per leg (NOTE 2) Operating junction and storage temperature range NOTES: (1) Bolt down on heat-sink with silicone thermal compound between bridge and mounting surface for maximum heat transfer with #6 screw (2) Unit mounted on 4.0 x 4.0 x 0.11" thick (10.5 x 10.5 x 0.3cm) Al. Plate (3) Unit mounted on P.C.B. at 0.375" (9.5mm) lead length with 0.5 x 0.5" (12 x 12mm) copper pads (4) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts 4/98 RATINGS AND CHARACTERISTICS CURVES GBPC1005 THRU GBPC110 FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG FIG. 1 - DERATING CURVE OUTPUT RECTIFIED CURRENT 60 CASE TEMPERATURE, TC HEAT-SINK MOUNTING, 4.0 x 4.0 x 0.11” THK (10.5 x 10.5 x 0.3cm) AL. PLATE 60 HZ RESISTIVE OR INDUCTIVE LOAD 4.0 3.0 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD OUTPUT CURRENT, AMPERES 5.0 2.0 1.0 AMBIENT TEMPERATURE, TA P.C.B. MOUNTING 0.375” (9.5mm) LEAD LENGTH 0 0 50 100 TC=60°C SINGLE SINE-WAVE (JEDEC METHOD) 50 40 30 20 10 150 1.0 CYCLE 0 1 10 100 NUMBER OF CYCLES AT 60 HZ AMBIENT TEMPERATURE, °C FIG. 4 - TYPICAL REVERSE LEAKAGE CHARACTERISTICS PER LEG FIG. 3 - TYPICAL FORWARD CHARACTERISTICS PER LEG 20 50 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES 10 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 1 0.1 10 TJ=125°C 1 0.1 TJ=25°C 0.01 0.4 0.6 0.8 1.0 1.2 1.4 0.01 0 1.6 FIG. 5 - TYPICAL JUNCTION CAPACITANCE PER LEG 60 80 100 FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE PER LEG 100 TJ=25°C f=1.0 MHz Vsig=50mVp-p 10 1.0 10 REVERSE VOLTAGE, VOLTS 100 TRANSIENT THERMAL IMPEDANCE, °C/W 100 JUNCTION CAPACITANCE, pF 40 PERCENT OF RATED PEAK REVERSE VOLTAGE, % INSTANTANEOUS FORWARD VOLTAGE, VOLTS 1 0.1 20 10 1 0.1 0.01 0.1 1 t, HEATING TIME, sec. 10 100