KBP005M THRU KBP10M 3N246 THRU 3N252 GLASS PASSIVATED SINGLE-PHASE RECTIFIER BRIDGE Reverse Voltage - 50 to 1000 Volts Forward Current - 1.5 Amperes Case Style KBPM FEATURES 0.600 (15.24) 0.560 (14.22) 0.125 x 45o (3.2) 0.460 (11.68) 0.420 (10.67) 0.500 (12.70) 0.460 (11.68) 0.50 (12.7) MIN. 60 (15.2) MIN. ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ This series is UL listed under Recognized Component Index, file number E54214 ♦ Glass passivated chip junctions ♦ High surge current capability ♦ Ideal for printed circuit board ♦ High temperature soldering guaranteed: 260°C/10 seconds at 5 lbs. (2.3kg) tension 0.060 (1.52) 0.034 (8.6) 0.028 (7.6) DIA. MECHANICAL DATA 0.160 (4.1) 0.140 (3.6) 0.105 (2.67) 0.085 (2.16) 0.200 (5.08) 0.180 (4.57) Polarity shown on front side of case: positive lead by beveled corner Case: Molded plastic body over passivated junctions Terminals: Plated lead solderable per MIL-STD-750, Method 2026 Polarity: Polarity symbols marked on case Mounting position: Any Weight: 0.06 ounce, 1.7 grams Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. KBP KBP 005M 01M SYMBOLS 3N246 3N247 KBP 02M 3N248 KBP 04M 3N249 KBP 06M 3N250 KBP 08M 3N251 KBP 10M 3N252 UNITS 100 200 400 600 800 1000 Volts * Maximum repetitive peak reverse voltage VRRM 50 * Maximum RMS voltage VRMS 35 70 140 280 420 560 700 Volts VDC 50 100 200 400 600 800 1000 Volts * Maximum DC blocking voltage Maximum average forward output rectified current at TA=40°C I(AV) 1.5 Amps IFSM 50.0 30.0 Amps I2t 10.0 A2sec at 1.0A per leg 1.57A per leg VF 1.0 1.3 Volts TA=25°C TA=125°C IR 5.0 500.0 µA CJ 15.0 pF RΘJA RΘJL 40.0 13.0 °C/W TJ, TSTG -55 to +150 °C * Peak forward surge current single half sine-wave superimposed on rated load (JEDEC Method) TJ=150°C Rating for fusing (t < 8.3ms) * Maximum instantaneous forward voltage drop * Maximum DC reverse current at rated DC blocking voltage per leg Typical junction capacitance per leg (NOTE 1) Typical thermal resistance per leg (NOTE 2) * Operating junction and storage temperature range NOTES: (1) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (2) Thermal resistance from junction to ambient and from junction to lead mounted on P.C.B. with, 0.47 x 0.47" (12 x12mm) copper pads * JEDEC registered values 4/98 RATINGS AND CHARACTERISTICS CURVES KBP005M THRU KBP10M / 3N246 THRU 3N252 FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 1.6 PEAK FORWARD SURGE CURRENT, AMPERES BRIDGE OUTPUT FULL WAVE RECTIFIED CURRENT, AVERAGE AMPERES FIG.1 - DERATING CURVE OUTPUT RECTIFIED CURRENT 60 Hz RESISTIVE OR INDUCTIVE LOAD 1.4 P.C.B. MOUNTED WITH 0.47 x 0.47” (12 x 12mm) COPPER PADS 1.2 1.0 0.8 0.6 CAPACITIVE LOAD Ipk/IAV=5.0 Ipk/IAV=10 Ipk/IAV=20 (PER LEG) 0.4 0.2 0 20 40 60 80 100 120 140 150 60 SINGLE SINE-WAVE (JEDEC Method) 50 40 TA=25°C 30 TJ=150°C 20 10 1.0 CYCLE 0 1 10 FIG. 3 - TYPICAL FORWARD CHARACTERISTICS PER LEG FIG. 4 - TYPICAL REVERSE LEAKAGE CHARACTERISTICS PER LEG 20 10 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES 10 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 1 TJ=125°C 1 TJ=100°C 0.1 TJ=25°C 0.01 0 0.1 20 40 60 80 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG. 5 - TYPICAL JUNCTION CAPACITANCE PER LEG 100 JUNCTION CAPACITANCE, pF 100 NUMBER OF CYCLES AT 60 HZ AMBIENT TEMPERATURE, °C TJ=25°C f=1.0 MHz Vsig=50mVp-p 10 1 0.1 1 10 REVERSE VOLTAGE, VOLTS 100 100