ALUMINUM ELECTROLYTIC CAPACITORS WT Chip Type, Wide Temperature Range series Chip type operating over wide temperature range of to – 55 to +105°C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2002/95/EC). WZ High Temperature Reflow WF Low impeadance UT Long Life WT Smaller ZT Specifications Item Performance Characteristics Category Temperature Range – 55 to +105°C Rated Voltage Range 4 to 50V Rated Capacitance Range 0.1 to 1500µF Capacitance Tolerance ±20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater. Measurement frequency : 120Hz at 20°C Tangent of loss angle (tan δ) Rated voltage (V) tan δ (MAX.) 4 0.40 6.3 0.30 10 0.24 16 0.20 25 0.16 35 0.14 50 0.14 Measurement frequency : 120Hz Stability at Low Temperature Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio Z– 40°C / Z+20°C ZT / Z20 (MAX.) The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 105°C. Endurance Shelf Life Resistance to soldering heat 4 7 15 6.3 4 8 10 3 8 16 2 4 25 2 4 35 2 3 50 2 3 Within ±25% of the initial capacitance value for capacitors of φ3mm unit, and 16V or less. Within ±20% of the initial capacitance value for capacitors of 25V or more. tan δ 200% or less than the initial specified value Leakage current Less than or equal to the initial specified value Capacitance change After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which Capacitance change Within ±10% of the initial capacitance value is maintained at 250°C. The capacitors shall meet the tan δ Less than or equal to the initial specified value characteristic requirements listed at right when they are Leakage current Less than or equal to the initial specified value removed from the plate and restored to 20°C. Black print on the case top. Marking Type numbering system (Example : 16V 10µF) Chip Type (φ3 to φ8 × 5.4 ) Positive L 2 Lot No. 1 0.5 MAX. 2 3 4 5 6 7 8 Package code Size code Configuration A±0.2 Capacitance tolerance (±20%) Rated capacitance (10µF) +0.1 –0.2 (L±0.3) Negative H 3 φD code 3 to 8 (5.4L) GB 6.3 to 10 (L 5.8) GS 9 10 11 12 13 14 UWT 1 C 1 0 0 MC L 1 G B A±0.2 C±0.2 E A2P 10 16V 105°C Marking Plastic platform 0.3 MAX. φD±0.5 1 Voltage B±0.2 Capacitance φD 3 to 8 (L 7.7) 8 to 10 (L = 10) code CL NL φD 3 4 to 10 code 2 1 Rated voltage (16V) 3 Apply to φ6.3 × 5.8, φ6.3 × 7.7 Series name Type (φ8 × 10, φ10 × 10 ) (mm) φD A±0.2 C±0.2 A±0.2 L±0.5 Lot No. Pressure relief vent ×L 3 × 5.4 4 × 5.4 A 1.5 1.8 2.1 2.4 2.4 2.4 3.3 2.9 3.2 B 3.3 4.3 5.3 6.6 6.6 6.6 8.3 8.3 10.3 C 3.3 4.3 5.3 6.6 6.6 6.6 8.3 8.3 10.3 E 0.8 1.0 1.3 2.2 2.2 2.2 2.3 3.1 4.5 5.4 5.4 5.4 5.4 5.8 7.7 5.4 10 10 5 × 5.4 6.3 × 5.4 6.3 × 5.8 6.3 × 7.7 8 × 5.4 8 × 10 10 × 10 E B±0.2 A2P 100 35V φD±0.5 1 Voltage 105°C Marking Trade mark Plastic platform 0.3 MAX. 0.5 MAX. Positive Capacitance Negative H L 1. Voltage mark for 6.3V is 6V . In case of marking for φ3 units, “V” for rated voltage is omitted. 2. In case of marking for φ3 units. Lot No is expressed by a digit (month code). H 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 Dimension table in next page. CAT.8100B ALUMINUM ELECTROLYTIC CAPACITORS WT series Dimensions V Cap. (µF) Code 4 0G 6.3 0J 10 1A 16 1C 25 1E 35 1V 50 1H 0.1 0R1 4 × 5.4 (3) 1.0 0.22 R22 4 × 5.4 (3) 2.6 0.33 R33 4 × 5.4 (3) 3.2 0.47 R47 4 × 5.4 (3) 3.8 1 010 4 × 5.4 (3) 6.3 (5.9) 2.2 2R2 3 × 5.4 7.5 4 × 5.4 (3) 11 (9) 3.3 3R3 3 × 5.4 9 4 × 5.4 14 4.7 4R7 4 × 5.4 (3) 13 (10) 4 × 5.4 15 5 × 5.4 19 5 × 5.4 23 5 × 5.4 25 6.3 × 5.4 30 42 8 × 5.4 4 × 5.4 (3) 18 (14) 10 100 22 220 4 × 5.4 22 4 × 5.4 22 5 × 5.4 27 5 × 5.4 30 6.3 × 5.4 38 6.3 × 5.4 33 330 5 × 5.4 30 5 × 5.4 30 5 × 5.4 35 6.3 × 5.4 40 6.3 × 5.4 48 8 × 5.4 47 470 5 × 5.4 36 5 × 5.4 36 6.3 × 5.4 46 6.3 × 5.4 50 8 × 5.4 100 101 6.3 × 5.4 60 6.3 × 5.4 60 6.3 × 5.4 60 6.3 × 5.4 60 6.3 × 7.7 150 151 6.3 × 5.8 86 6.3 × 5.8 86 220 221 8 × 5.4 330 331 6.3 × 7.7 105 6.3 × 7.7 105 470 471 8 × 10 210 8 × 10 680 681 8 × 10 210 8 × 10 1000 102 8 × 10 230 1500 152 10 × 10 310 102 (91) 59 (52) 6.3 × 7.7 51 (45) 60 66 (59) 6.3 × 5.8 63 6.3 × 7.7 63 91 6.3 × 7.7 84 8 × 10 140 6.3 × 5.8 86 6.3 × 7.7 95 8 × 10 140 8 × 10 155 10 × 10 180 102 (91) 6.3 × 7.7 105 6.3 × 7.7 105 8 × 10 155 8 × 10 190 10 × 10 220 8 × 10 195 8 × 10 195 8 × 10 190 10 × 10 300 210 8 × 10 210 8 × 10 230 10 × 10 300 210 10 × 10 310 10 × 10 310 8 × 10 230 10 × 10 310 10 × 10 310 8 × 5.4 ( ) is also available with φ3mm upon request. In such a case, 2 will be put at 12th digit of type numbering system. Size φ6.3 × 5.8 is available for capacitors marked. " " In such a case, 6 will be put at 12th digit of type numbering system. Case size Rated φ D × L (mm) ripple Rated ripple current (mArms) at 105°C 120Hz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz or more 1.50 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please select UX(p.110), UJ(p.116) series if high C/V products are reqired. Please refer to page 3 for the minimum order quantity. CAT.8100B