TI TPS54910

Typical Size
6,4 mm X 9,7 mm
TPS54910
www.ti.com
SLVS421B – MARCH 2002 – REVISED AUGUST 2002
3-V TO 4-V INPUT, 9-A OUTPUT SYNCHRONOUS BUCK PWM
SWITCHER WITH INTEGRATED FETs (SWIFT)
FEATURES
D 15-mΩ MOSFET Switches for High Efficiency
D
D
D
D
D
D
DESCRIPTION
As a member of the SWIFT family of dc/dc regulators,
the TPS54910 low-input voltage high-output current
synchronous buck PWM converter integrates all
required active components. Included on the substrate
with the listed features are a true, high performance,
voltage error amplifier that enables maximum
performance under transient conditions and flexibility in
choosing the output filter L and C components; an
under-voltage-lockout circuit to prevent start-up until
the input voltage reaches 3 V; an internally and
externally set slow-start circuit to limit in-rush currents;
and a power good output useful for processor/logic
reset, fault signaling, and supply sequencing.
at 9-A Continuous Output
0.9-V to 2.5-V Adjustable Output Voltage
Externally Compensated With 1% Accuracy
Fast Transient Response
Wide PWM Frequency:
Fixed 350 kHz, 550 kHz or
Adjustable 280 kHz to 700 kHz
Load Protected by Peak Current Limit and
Thermal Shutdown
Integrated Solution Reduces Board Area and
Total Cost
APPLICATIONS
D Low-Voltage, High-Density Systems With
The TPS54910 is available in a thermally enhanced
28-pin TSSOP (PWP) PowerPAD package, which
eliminates bulky heatsinks. TI provides evaluation
modules and the SWIFT designer software tool to aid
in quickly achieving high-performance power supply
designs to meet aggressive equipment development
cycles.
Power Distributed at 3.3 V
D Point of Load Regulation for High
D
D
Performance DSPs, FPGAs, ASICs and
Microprocessors
Broadband, Networking and Optical
Communications Infrastructure
Portable Computing/Notebook PCs
SIMPLIFIED SCHEMATIC
EFFICIENCY AT 700 kHz
SIMPLIFIED SCHEMATIC
Input
VIN
PH
100
90
Efficiency – %
TPS54910
BOOT
PGND
VBIAS
95
Output
COMP
85
80
75
70
65
AGND VSENSE
60
Compensation
Network
VI = 3.3 V,
VO = 2.5 V
55
50
0
1
2
3
4
5
6
7
8
9
10 11 12
IO – Output Current – A
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments
semiconductor products and disclaimers thereto appears at the end of this data sheet.
PowerPAD and SWIFT are trademarks of Texas Instruments.
PRODUCTION DATA information is current as of publication date. Products
conform to specifications per the terms of Texas Instruments standard warranty.
Production processing does not necessarily include testing of all parameters.
Copyright  2002, Texas Instruments Incorporated
TPS54910
www.ti.com
SLVS421B – MARCH 2002 – REVISED AUGUST 2002
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during
storage or handling to prevent electrostatic damage to the MOS gates.
ORDERING INFORMATION
TA
– 40°C to 85°C
OUTPUT VOLTAGE
0.9 V to 2.5 V
PACKAGE
Plastic HTSSOP (PWP)(1)
PART NUMBER
TPS54910PWP
(1) The PWP package is also available taped and reeled. Add an R suffix to the device type (i.e., TPS54910PWPR). See the application section of
the data sheet for PowerPAD drawing and layout information.
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range unless otherwise noted(1)
TPS54910
Input
In
ut voltage range, VI
Output voltage range,
range VO
SS/ENA, SYNC
–0.3 to 7
RT
–0.3 to 6
VSENSE
–0.3 to 4
VIN
–0.3 to 4.5
BOOT
–0.3 to 10
VBIAS, COMP, PWRGD
–0.3 to 7
PH
–0.6 to 6
PH
Source current
current, IO
Sink current, IS
UNIT
V
V
Internally Limited
COMP, VBIAS
6
mA
PH
16
A
COMP
6
SS/ENA, PWRGD
10
mA
±0.3
V
Operating virtual junction temperature range, TJ
–40 to 125
°C
Storage temperature, Tstg
–65 to 150
°C
Voltage differential
AGND to PGND
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds
300
°C
(1) Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
MIN
Input voltage, VI
Operating junction temperature, TJ
NOM
MAX
UNIT
3
4
V
–40
125
°C
DISSIPATION RATINGS(1)(2)
PACKAGE
THERMAL IMPEDANCE
JUNCTION-TO-AMBIENT
TA = 25°C
POWER RATING
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
28 Pin PWP with solder
14.4°C/W
6.94 W(3)
3.81 W
2.77 W
28 Pin PWP without solder
27.9°C/W
3.58 W
1.97 W
1.43 W
(1) For more information on the PWP package, refer to TI technical brief, literature number SLMA002.
(2) Test board conditions:
1. 3” x 3”, 4 layers, thickness: 0.062”
2. 1.5 oz. copper traces located on the top of the PCB
3. 1.5 oz. copper ground plane on the bottom of the PCB
4. 0.5 oz. copper ground planes on the 2 internal layers
5. 12 thermal vias (see “Recommended Land Pattern” in applications section of this data sheet)
(3) Maximum power dissipation may be limited by over current protection.
2
TPS54910
www.ti.com
SLVS421B – MARCH 2002 – REVISED AUGUST 2002
ELECTRICAL CHARACTERISTICS
TJ = –40°C to 125°C, VI = 3 V to 4 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
SUPPLY VOLTAGE, VIN
Input voltage range, VIN
I(Q)
Quiescent current
3.0
4.0
fs = 350 kHz, SYNC ≤ 0.8 V, RT open,
PH pin open
9.8
17.0
fs = 550 kHz, SYNC ≥ 2.5 V, RT open,
PH pin open
14.0
23.0
1
1.4
2.95
3.0
Shutdown, SS/ENA = 0 V
V
mA
UNDER VOLTAGE LOCK OUT
Start threshold voltage, UVLO
V
Stop threshold voltage, UVLO
2.70
2.80
Hysteresis voltage, UVLO
0.14
0.16
V
2.5
µs
Rising and falling edge deglitch, UVLO(1)
V
BIAS VOLTAGE
Output voltage, VBIAS
I(VBIAS) = 0
2.70
2.80
Output current, VBIAS (2)
2.90
V
100
µA
CUMULATIVE REFERENCE
Vref
Accuracy
REGULATION
Lineregulation
Line
regulation(1)(3)
Loadregulation
Load
regulation(1)(3)
0.882
0.891
0.900
IL = 4.5 A, fs = 350 kHz, TJ = 85°C
IL = 4.5 A, fs = 550 kHz, TJ = 85°C
IL = 0 A to 9 A, fs = 350 kHz, TJ = 85°C
0.07
IL = 0 A to 9 A, fs = 550 kHz, TJ = 85°C
0.03
0.07
V
%/V
0.03
%/A
OSCILLATOR
Internally set—free
set free running frequency
Externally set
set—free
free running frequency range
High level threshold, SYNC
SYNC ≤ 0.8 V,
RT open
280
350
420
SYNC ≥ 2.5 V,
RT open
440
550
660
RT = 180 kΩ (1% resistor to AGND)
252
280
308
RT = 100 kΩ (1% resistor to AGND)
460
500
540
RT = 68 kΩ (1% resistor to AGND)
663
700
762
2.5
Frequency range, SYNC(1)
Ramp valley(1)
0.8
50
Maximum duty cycle(1)
V
ns
330
700
0.75
Ramp amplitude (peak-to-peak)(1)
Minimum controllable on time(1)
kHz
V
Low level threshold, SYNC
Pulse duration, external synchronization,
SYNC(1)
kHz
kHz
V
1
V
200
ns
90%
(1) Specified by design
(2) Static resistive loads only
(3) Specified by the circuit used in Figure 10
3
TPS54910
www.ti.com
SLVS421B – MARCH 2002 – REVISED AUGUST 2002
ELECTRICAL CHARACTERISTICS (continued)
TJ = –40°C to 125°C, VI = 3 V to 4 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
ERROR AMPLIFIER
Error amplifier open loop voltage gain
1 kΩ COMP to AGND(1)
90
110
Error amplifier unity gain bandwidth
Parallel 10 kΩ, 160 pF COMP to AGND(1)
3
5
Error amplifier common mode input voltage
range
Powered by internal LDO(1)
0
Input bias current, VSENSE
VSENSE = Vref
Output voltage slew rate (symmetric), COMP
VBIAS
60
1.0
dB
MHz
250
1.4
V
nA
V/µs
PWM COMPARATOR
PWM comparator propagation delay time,
PWM comparator input to PH pin
(excluding deadtime)
10-mV overdrive(1)
70
85
ns
1.2
1.4
V
SLOW-START/ENABLE
Enable threshold voltage, SS/ENA
0.82
Enable hysteresis voltage, SS/ENA(1)
Falling edge deglitch, SS/ENA(1)
Internal slow-start time
Charge current, SS/ENA
SS/ENA = 0 V
Discharge current, SS/ENA
SS/ENA = 1.3 V, VI = 1.5 V
0.03
V
2.5
µs
2.6
3.35
4.1
3
5
8
ms
µA
1.5
2.3
4.0
mA
POWER GOOD
Power good threshold voltage
VSENSE falling
90
Power good hysteresis voltage(1)
Power good falling edge deglitch(1)
Output saturation voltage, PWRGD
Leakage current, PWRGD
%Vref
%Vref
3
µs
35
I(sink) = 2.5 mA
VI = 5.5 V
0.18
0.3
V
1
µA
CURRENT LIMIT
Current limit
VI = 3.3 V(1), Output shorted
15
A
Current limit leading edge blanking time
11
100
ns
Current limit total response time
200
ns
THERMAL SHUTDOWN
Thermal shutdown trip point(1)
Thermal shutdown hysteresis(1)
135
150
165
°C
°C
10
OUTPUT POWER MOSFETS
rDS(on)
P
Power
MOSFET switches
it h
VI = 3 V(4)
VI = 3.6 V(4)
(1) Specified by design
(2) Static resistive loads only
(3) Specified by the circuit used in Figure 10
(4) Matched MOSFETs low-side rDS(on) production tested, high-side rDS(on) production tested.
4
15
30
14
28
mΩ
Ω
TPS54910
www.ti.com
SLVS421B – MARCH 2002 – REVISED AUGUST 2002
PWP PACKAGE
(TOP VIEW)
AGND
VSENSE
COMP
PWRGD
BOOT
PH
PH
PH
PH
PH
PH
PH
PH
PH
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
THERMAL 22
PAD
21
20
19
18
17
16
15
RT
SYNC
SS/ENA
VBIAS
VIN
VIN
VIN
VIN
VIN
PGND
PGND
PGND
PGND
PGND
TERMINAL FUNCTIONS
TERMINAL
NAME
NO.
DESCRIPTION
AGND
1
Analog ground. Return for compensation network/output divider, slow-start capacitor, VBIAS capacitor, RT resistor and
SYNC pin. Connect PowerPAD to AGND.
BOOT
5
Bootstrap output. 0.022-µF to 0.1-µF low-ESR capacitor connected from BOOT to PH generates floating drive for the
high-side FET driver.
COMP
3
Error amplifier output. Connect frequency compensation network from COMP to VSENSE
PGND
15–19
Power ground. High current return for the low-side driver and power MOSFET. Connect PGND with large copper areas
to the input and output supply returns, and negative terminals of the input and output capacitors. A single point connection
to AGND is recommended.
PH
6–14
Phase output. Junction of the internal high-side and low-side power MOSFETs, and output inductor.
PWRGD
4
Power good open drain output. High when VSENSE ≥ 90% Vref, otherwise PWRGD is low. Note that output is low when
SS/ENA is low or the internal shutdown signal is active.
RT
28
Frequency setting resistor input. Connect a resistor from RT to AGND to set the switching frequency, fs.
SS/ENA
26
Slow-start/enable input/output. Dual function pin which provides logic input to enable/disable device operation and
capacitor input to externally set the start-up time.
SYNC
27
Synchronization input. Dual function pin which provides logic input to synchronize to an external oscillator or pin select
between two internally set switching frequencies. When used to synchronize to an external signal, a resistor must be
connected to the RT pin.
VBIAS
25
Internal bias regulator output. Supplies regulated voltage to internal circuitry. Bypass VBIAS pin to AGND pin with a
high-quality, low-ESR 0.1-µF to 1.0-µF ceramic capacitor.
20–24
Input supply for the power MOSFET switches and internal bias regulator. Bypass VIN pins to PGND pins close to device
package with a high-quality, low-ESR 10-µF ceramic capacitor.
VIN
VSENSE
2
Error amplifier inverting input. Connect to output voltage compensation network/output divider.
5
TPS54910
www.ti.com
SLVS421B – MARCH 2002 – REVISED AUGUST 2002
INTERNAL BLOCK DIAGRAM
VBIAS
AGND
VIN
Enable
Comparator
SS/ENA
Falling
Edge
Deglitch
1.2 V
Hysteresis: 0.03 V
2.5 µs
VIN UVLO
Comparator
VIN
2.95 V
Hysteresis: 0.16 V
REG
VBIAS
SHUTDOWN
VIN
ILIM
Comparator
Thermal
Shutdown
150°C
3–6V
Leading
Edge
Blanking
Falling
and
Rising
Edge
Deglitch
100 ns
BOOT
15 mΩ
2.5 µs
SS_DIS
SHUTDOWN
Internal/External
Slow-start
(Internal Slow-start Time = 3.35 ms
PH
+
–
R Q
Error
Amplifier
Reference
VREF = 0.891 V
S
PWM
Comparator
LOUT
CO
Adaptive Dead-Time
and
Control Logic
VIN
15 mΩ
OSC
PGND
Powergood
Comparator
PWRGD
VSENSE
Falling
Edge
Deglitch
0.90 Vref
TPS54910
Hysteresis: 0.03 Vref
VSENSE
COMP
RELATED DC/DC PRODUCTS
D TPS40000—dc/dc controller
D TPS56300—dc/dc controller
D PT6600 series—9 A plugin modules
6
RT
SYNC
SHUTDOWN
35 µs
VO
TPS54910
www.ti.com
SLVS421B – MARCH 2002 – REVISED AUGUST 2002
TYPICAL CHARACTERISTICS
DRAIN-SOURCE
ON-STATE RESISTANCE
vs
JUNCTION TEMPERATURE
VIN = 3.0 V
IO = 9 A
20
15
10
5
0
–40
0
25
85
TJ – Junction Temperature – °C
25
VIN = 3.6 V
IO = 9 A
20
15
10
5
0
–40
125
0
85
125
650
SYNC ≥ 2.5 V
550
450
SYNC ≤ 0.8 V
350
250
–40
0
8
VI = 3.3 V
TJ = 125°C
7
600
500
RT = 100 kΩ
400
300
0.893
Device Power Losses – W
V ref – Voltage Reference – V
RT = 68 kΩ
125
DEVICE POWER LOSSES
vs
LOAD CURRENT
0.895
700
85
Figure 3
VOLTAGE REFERENCE
vs
JUNCTION TEMPERATURE
800
25
TJ – Junction Temperature – °C
Figure 2
EXTERNALLY SET
OSCILLATOR FREQUENCY
vs
JUNCTION TEMPERATURE
0.891
0.889
0.887
6
5
4
3
2
1
RT = 180 kΩ
0.885
0
25
85
125
0
–40
TJ – Junction Temperature – °C
0
25
85
TJ – Junction Temperature – °C
Figure 4
RL = 10 kΩ,
CL = 160 pF,
TA = 25°C
120
0.893
100
Gain – dB
0.891
0.889
80
Phase
Gain
20
0.887
–80
–140
–160
0
0.885
–180
–20
3.5
3.6
1
10
100
–200
1 k 10 k 100 k 1 M 10 M
f – Frequency – Hz
Figure 8
12
14
16
3.80
–40
–120
40
10
–20
–100
60
8
INTERNAL SLOW-START TIME
vs
JUNCTION TEMPERATURE
–60
Figure 7
6
Figure 6
0
140
3.2
3.3
3.4
VI – Input Voltage – V
4
IL – Load Current – A
ERROR AMPLIFIER
OPEN LOOP RESPONSE
0.895
3.1
2
Figure 5
OUTPUT VOLTAGE REGULATION
vs
INPUT VOLTAGE
3
0
125
Phase – Degrees
200
–40
Internal Slow-Start Time – ms
f – Externally Set Oscillator Frequency – kHz
25
750
TJ – Junction Temperature – °C
Figure 1
VO – Output Voltage Regulation – V
INTERNALLY SET
OSCILLATOR FREQUENCY
vs
JUNCTION TEMPERATURE
f – Internally Set Oscillator Frequency – kHz
25
Drain Source On-State Reststance – m Ω
Drain Source On-State Reststance – m Ω
DRAIN-SOURCE
ON-STATE RESISTANCE
vs
JUNCTION TEMPERATURE
3.65
3.50
3.35
3.20
3.05
2.90
2.75
–40
0
25
85
125
TJ – Junction Temperature – °C
Figure 9
7
TPS54910
www.ti.com
SLVS421B – MARCH 2002 – REVISED AUGUST 2002
APPLICATION INFORMATION
Figure 10 shows the schematic diagram for a typical
TPS54910 application. The TPS54910 (U1) can provide
up to 9 A of output current at a nominal output voltage of
1.8 V. For proper thermal performance, the exposed
VI
C10
10 µF
C12
10 µF
U1
TPS54910PWP
R6
28
RT
VIN
71.5 kΩ
VIN
27
R7
10 kΩ
C6
26
0.047 µF
25
C3
VIN
SYNC
VIN
VIN
SS/ENA
PH
PH
VBIAS
1 µF
PH
4
C1
1000 pF
R2
R3
301 Ω
10 kΩ
PH
PWRGD
C4
PH
3
PH
COMP
3300 pF
PH
C2
PH
R1
10 Ω
thermal PowerPAD underneath the integrated circuit,
TPS54910, package must be soldered to the
printed-circuit board.
150 pF
2
PH
VSENSE
BOOT
PGND
PGND
R4
9.76 kΩ
1
PGND
AGND
PGND
PGND
POWERPAD
24
23
22
21
20
14
13
12
11
L1
0.65 µH
10
9
VO
8
C8
22 µF
7
C7
22 µF
C5
22 µF
6
5
C9
19
0.047 µF
18
R7
2.4 Ω
17
16
15
C11
3300 pF
Analog and Power Grounds Are Tied at the Pad Under the Package of IC
Figure 10. Application Circuit
COMPONENT SELECTION
FEEDBACK CIRCUIT
The values for the components used in this design
example were selected for best load transient response
and small PCB area. Additional design information is
available at www.ti.com.
The values for these components are selected to provide
fast transient response times.
INPUT FILTER
The input voltage is a nominal 3.3 VDC. The input filter
(C10) is a 10-µF ceramic capacitor (Taiyo Yuden). C12 is
also a 10-µF ceramic capacitor (Taiyo Yuden) that
provides high-frequency decoupling of the TPS54910
from the input supply. C12 must be located as close as
possible to the device. Ripple current is carried in both C10
and C12, and the return path to PGND must avoid the
current circulating in the output capacitors C5, C7, and C8.
The resistor divider network of R1 and R4 sets the output
voltage for the circuit at 1.8 V. R1 along with R2, R3, C1,
C2, and C4 forms the loop compensation network for the
circuit. For this design, a Type-3 topology is used.
OPERATING FREQUENCY
In the application circuit, RT is grounded through a 71.5-kΩ
resistor to select the operating frequency of 700 kHz. To
set a different frequency, place a 68-kΩ to 180-kΩ resistor
between RT (pin 28) and analog ground or leave RT
floating to select the default of 350 kHz. The resistance can
be approximated using the following equation:
R+
8
500 kHz
Switching Frequency
100 [kW]
(1)
TPS54910
www.ti.com
SLVS421B – MARCH 2002 – REVISED AUGUST 2002
OUTPUT FILTER
The output filter is composed of a 0.65-µH inductor and
3 x 22-µF capacitor. The inductor is a low dc-resistance
(.017 Ω) type, Pulse Engineering PA0277. The capacitors
used are 22-µF, 6.3-V ceramic types with X5R dielectric.
The feedback loop is compensated so that the unity gain
frequency is approximately 75 kHz.
GROUNDING AND POWERPAD LAYOUT
The TPS54910 has two internal grounds (analog and
power). Inside the TPS54910, the analog ground ties to all
of the noise sensitive signals, while the power ground ties
to the noisier power signals. The PowerPAD must be tied
directly to AGND. Noise injected between the two grounds
can degrade the performance of the TPS54910,
particularly at higher output currents. However, ground
noise on an analog ground plane can also cause problems
with some of the control and bias signals. For these
reasons, separate analog and power ground planes are
recommended. These two planes must tie together
directly at the IC to reduce noise between the two grounds.
The only components that must tie directly to the power
ground plane are the input capacitor, the output capacitor,
the input voltage decoupling capacitor, and the PGND pins
of the TPS54910. The layout of the TPS54910 evaluation
module is representative of a recommended layout for a
8 PL Ø 0.0130
4 PL
Ø 0.0180
4-layer board. Documentation for the TPS54910
evaluation module can be found on the Texas Instruments
web site under the TPS54910 product folder.
LAYOUT CONSIDERATIONS FOR THERMAL
PERFORMANCE
For operation at full rated load current, the analog ground
plane must provide an adequate heat dissipating area. A
3-inch by 3-inch plane of 1 ounce copper is recommended,
though not mandatory, depending on ambient temperature
and airflow. Most applications have larger areas of internal
ground plane available, and the PowerPAD must be
connected to the largest area available. Additional areas
on the top or bottom layers also help dissipate heat, and
any area available must be used when 6 A or greater
operation is desired. Connection from the exposed area of
the PowerPAD to the analog ground plane layer must be
made using 0.013-inch diameter vias to avoid solder
wicking through the vias.
Eight vias must be in the PowerPAD area with four
additional vias located under the device package. The size
of the vias under the package, but not in the exposed
thermal pad area, can be increased to 0.018. Additional
vias beyond the twelve recommended that enhance
thermal performance must be included in areas not under
the device package.
Minimum Recommended Thermal Vias: 8 x 0.013 Diameter Inside
Powerpad Area 4 x 0.018 Diameter Under Device as Shown.
Additional 0.018 Diameter Vias May Be Used if Top Side Analog Ground
Area Is Extended.
Connect Pin 1 to Analog Ground Plane
in This Area for Optimum Performance
0.06
0.0150
0.0339
0.0650
0.0500
0.3820 0.3478 0.0500
0.0500
0.2090
0.0256
0.0650
0.0339
0.1700
0.1340
Minimum Recommended Top
Side Analog Ground Area
Minimum Recommended Exposed
Copper Area for Powerpad. 5mm
Stencils May Require 10 Percent
Larger Area
0.0630
0.0400
Figure 11. Recommended Land Pattern for 28-Pin PWP PowerPAD
9
TPS54910
www.ti.com
SLVS421B – MARCH 2002 – REVISED AUGUST 2002
PERFORMANCE GRAPHS
EFFICIENCY
vs
OUTPUT CURRENT
LOAD REGULATION
vs
OUTPUT CURRENT
1.003
1.001
fs = 700 kHz,
TA = 25°C,
VI = 3.3 V,
VO = 1.8 V
95
1.002
80
75
70
65
fs = 700 kHz,
VI = 3.3 V,
VO = 2.5 V
60
55
50
0
1
2
3
4
5
6
7
8
9
1.0006
1.001
Line Regulation
85
Load Regulation
Efficiency – %
90
1.0008
0
0.999
10 11 12
0
2
4
6
8
10
55
45
35
8
3
3.2
10
12
14
3.6
t – Time – 5 µs/div
IO – Output Current – A
Figure 15
Figure 16
Figure 17
VI = 3.3 V,
VO = 1.8 V
0.047 µf
slow-start capacitor
t –Time – 5 ms/div
Figure 18
(1) Safe operating area is applicable to the test board conditions in the Dissipation Ratings
VO – Output Voltage – 1 V/div
VI – Input Voltage – 1 V/div
SLOW-START TIMING
10
3.8
4
VI = 3.3 V,
VO = 1.8 V
2 A to 6.5 A
t – Time – 1 µs/div
16
3.4
TRANSIENT RESPONSE
VO – Output Voltage – 10 mV/div
65
6
fs = 700 kHz,
TA = 25°C,
VI = 3.3 V,
VO = 1.8 V
Figure 14
fs = 700 kHz,
IO = 9 A,
VI = 3.3 V,
VO = 1.8 V
Output Ripple Voltage – 10 mV/div
Ambient Temperature – ° C
75
4
0.999
OUTPUT RIPPLE VOLTAGE
85
2
IO = 4.5 A
Figure 13
fs = 700 kHz,
TJ = 125°C,
VI = 3.3 V,
VO = 1.8 V
0
0.9996
VI – Input Voltage – V
125
25
1
0.9998
IO – Output Current – A
AMBIENT TEMPERATURE
vs
LOAD CURRENT(1)
95
IO = 0 A
0.9992
0.997
Figure 12
105
IO = 9 A
1.0002
0.9994
0.998
IO – Output Current – A
115
1.0004
I O – Output Current – 2 A/div
100
LINE REGULATION
vs
INPUT VOLTAGE
TPS54910
www.ti.com
SLVS421B – MARCH 2002 – REVISED AUGUST 2002
DETAILED DESCRIPTION
VBIAS REGULATOR (VBIAS)
UNDERVOLTAGE LOCK OUT (UVLO)
The TPS54910 incorporates an under voltage lockout
circuit to keep the device disabled when the input voltage
(VIN) is insufficient. During power up, internal circuits are
held inactive until VIN exceeds the nominal UVLO
threshold voltage of 2.95 V. Once the UVLO start threshold
is reached, device start-up begins. The device operates
until VIN falls below the nominal UVLO stop threshold of
2.8 V. Hysteresis in the UVLO comparator, and a 2.5-µs
rising and falling edge deglitch circuit reduce the likelihood
of shutting the device down due to noise on VIN.
SLOW-START/ENABLE (SS/ENA)
VOLTAGE REFERENCE
The slow-start/enable pin provides two functions. First, the
pin acts as an enable (shutdown) control by keeping the
device turned off until the voltage exceeds the start
threshold voltage of approximately 1.2 V. When SS/ENA
exceeds the enable threshold, device start-up begins. The
reference voltage fed to the error amplifier is linearly
ramped up from 0 V to 0.891 V in 3.35 ms. Similarly, the
converter output voltage reaches regulation in
approximately 3.35 ms. Voltage hysteresis and a 2.5-µs
falling edge deglitch circuit reduce the likelihood of
triggering the enable due to noise.
The second function of the SS/ENA pin provides an
external means of extending the slow-start time with a
low-value capacitor connected between SS/ENA and
AGND.
Adding a capacitor to the SS/ENA pin has two effects on
start-up. First, a delay occurs between release of the
SS/ENA pin and start-up of the output. The delay is
proportional to the slow-start capacitor value and lasts
until the SS/ENA pin reaches the enable threshold. The
start-up delay is approximately:
t +C
d
(SS)
1.2 V
5 mA
(2)
Second, as the output becomes active, a brief ramp-up at
the internal slow-start rate may be observed before the
externally set slow-start rate takes control and the output
rises at a rate proportional to the slow-start capacitor. The
slow-start time set by the capacitor is approximately:
t
(SS)
+C
(SS)
0.7 V
5 mA
The VBIAS regulator provides internal analog and digital
blocks with a stable supply voltage over variations in
junction temperature and input voltage. A high quality,
low-ESR, ceramic bypass capacitor is required on the
VBIAS pin. X7R or X5R grade dielectrics are
recommended because their values are more stable over
temperature. The bypass capacitor must be placed close
to the VBIAS pin and returned to AGND.
External loading on VBIAS is allowed, with the caution that
internal circuits require a minimum VBIAS of 2.70 V, and
external loads on VBIAS with ac or digital switching noise
may degrade performance. The VBIAS pin may be useful
as a reference voltage for external circuits.
(3)
The actual slow-start time is likely to be less than the above
approximation due to the brief ramp-up at the internal rate.
The voltage reference system produces a precise Vref
signal by scaling the output of a temperature stable
bandgap circuit. During manufacture, the bandgap and
scaling circuits are trimmed to produce 0.891 V at the
output of the error amplifier, with the amplifier connected
as a voltage follower. The trim procedure adds to the high
precision regulation of the TPS54910, since it cancels
offset errors in the scale and error amplifier circuits.
OSCILLATOR AND PWM RAMP
The oscillator frequency can be set to internally fixed
values of 350 kHz or 550 kHz using the SYNC pin as a
static digital input. If a different frequency of operation is
required for the application, the oscillator frequency can be
externally adjusted from 280 to 700 kHz by connecting a
resistor between the RT pin to ground and floating the
SYNC pin. The switching frequency is approximated by
the following equation, where R is the resistance from RT
to AGND:
(4)
Switching Frequency + 100 kW 500 [kHz]
R
External synchronization of the PWM ramp is possible
over the frequency range of 330 kHz to 700 kHz by driving
a synchronization signal into SYNC and connecting a
resistor from RT to AGND. Choose a RT resistor that sets
the free running frequency to 80% of the synchronization
signal. The following table summarizes the frequency
selection configurations:
SWITCHING
FREQUENCY
SYNC PIN
RT PIN
350 kHz, internally set Float or AGND
Float
550 kHz, internally set ≥ 2.5 V
Float
Externally set 280
kHz to 700 kHz
Float
R = 68 kΩ to 180 kΩ
Externally
synchronized
frequency
Synchronization
signal
R = RT value for 80%
of external synchronization frequency
11
TPS54910
www.ti.com
SLVS421B – MARCH 2002 – REVISED AUGUST 2002
ERROR AMPLIFIER
The high performance, wide bandwidth, voltage error
amplifier sets the TPS54910 apart from most dc/dc
converters. The user is given the flexibility to use a wide
range of output L and C filter components to suit the
particular application needs. Type-2 or Type-3
compensation can be employed using external
compensation components.
PWM CONTROL
Signals from the error amplifier output, oscillator, and
current limit circuit are processed by the PWM control
logic. Referring to the internal block diagram, the control
logic includes the PWM comparator, OR gate, PWM latch,
and portions of the adaptive dead-time and control-logic
block. During steady-state operation below the current
limit threshold, the PWM comparator output and oscillator
pulse train alternately reset and set the PWM latch. Once
the PWM latch is set, the low-side FET remains on for a
minimum duration set by the oscillator pulse width. During
this period, the PWM ramp discharges rapidly to its valley
voltage. When the ramp begins to charge back up, the
low-side FET turns off and high-side FET turns on. As the
PWM ramp voltage exceeds the error amplifier output
voltage, the PWM comparator resets the latch, thus
turning off the high-side FET and turning on the low-side
FET. The low-side FET remains on until the next oscillator
pulse discharges the PWM ramp.
During transient conditions, the error amplifier output
could be below the PWM ramp valley voltage or above the
PWM peak voltage. If the error amplifier is high, the PWM
latch is never reset, and the high-side FET remains on until
the oscillator pulse signals the control logic to turn the
high-side FET off and the low-side FET on. The device
operates at its maximum duty cycle until the output voltage
rises to the regulation set-point, setting VSENSE to
approximately the same voltage as VREF. If the error
amplifier output is low, the PWM latch is continually reset
and the high-side FET does not turn on. The low-side FET
remains on until the VSENSE voltage decreases to a
range that allows the PWM comparator to change states.
The TPS54910 is capable of sinking current continuously
until the output reaches the regulation set-point.
If the current limit comparator trips for longer than 100 ns,
the PWM latch resets before the PWM ramp exceeds the
error amplifier output. The high-side FET turns off and
low-side FET turns on to decrease the energy in the output
inductor and consequently the output current. This
process is repeated each cycle in which the current limit
comparator is tripped.
DEAD-TIME CONTROL AND MOSFET
DRIVERS
Adaptive dead-time control prevents shoot-through
current from flowing in both N-channel power MOSFETs
12
during the switching transitions by actively controlling the
turnon times of the MOSFET drivers. The high-side driver
does not turn on until the voltage at the gate of the low-side
FET is below 2 V. While the low-side driver does not turn
on until the voltage at the gate of the high-side MOSFET
is below 2 V.
The high-side and low-side drivers are designed with
300-mA source and sink capability to quickly drive the
power MOSFETs gates. The low-side driver is supplied
from VIN, while the high-side drive is supplied from the
BOOT pin. A bootstrap circuit uses an external BOOT
capacitor and an internal 2.5-Ω bootstrap switch
connected between the VIN and BOOT pins. The
integrated bootstrap switch improves drive efficiency and
reduces external component count.
OVERCURRENT PROTECTION
The cycle-by-cycle current limiting is achieved by sensing
the current flowing through the high-side MOSFET and
comparing this signal to a preset overcurrent threshold.
The high side MOSFET is turned off within 200 ns of
reaching the current limit threshold. A 100-ns leading edge
blanking circuit prevents current limit false tripping.
Current limit detection occurs only when current flows from
VIN to PH when sourcing current to the output filter. Load
protection during current sink operation is provided by
thermal shutdown.
THERMAL SHUTDOWN
The device uses the thermal shutdown to turn off the power
MOSFETs and disable the controller if the junction
temperature exceeds 150°C. The device is released from
shutdown automatically when the junction temperature
decreases to 10°C below the thermal shutdown trip point,
and starts up under control of the slow-start circuit.
Thermal shutdown provides protection when an overload
condition is sustained for several milliseconds. With a
persistent fault condition, the device cycles continuously;
starting up by control of the soft-start circuit, heating up due
to the fault condition, and then shutting down upon
reaching the thermal shutdown trip point. This sequence
repeats until the fault condition is removed.
POWER-GOOD (PWRGD)
The power good circuit monitors for under voltage
conditions on VSENSE. If the voltage on VSENSE is 10%
below the reference voltage, the open-drain PWRGD
output is pulled low. PWRGD is also pulled low if VIN is
less than the UVLO threshold or SS/ENA is low. When VIN
≥ UVLO threshold, SS/ENA ≥ enable threshold, and
VSENSE > 90% of Vref, the open drain output of the
PWRGD pin is high. A hysteresis voltage equal to 3% of
Vref and a 35 µs falling edge deglitch circuit prevent
tripping of the power good comparator due to high
frequency noise.
TPS54910
www.ti.com
SLVS421B – MARCH 2002 – REVISED AUGUST 2002
MECHANICAL DATA
PWP (R-PDSO-G**)
POWERPAD PLASTIC SMALL-OUTLINE
20 PINS SHOWN
0,30
0,19
0,65
20
0,10 M
11
Thermal Pad
(See Note D)
4,50
4,30
0,15 NOM
6,60
6,20
Gage Plane
1
10
0,25
A
0°–ā8°
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
14
16
20
24
28
A MAX
5,10
5,10
6,60
7,90
9,80
A MIN
4,90
4,90
6,40
7,70
9,60
DIM
4073225/F 10/98
NOTES:A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusions.
The package thermal performance may be enhanced by bonding the thermal pad to an external thermal plane.
This pad is electrically and thermally connected to the backside of the die and possibly selected leads.
E. Falls within JEDEC MO-153
PowerPAD is a trademark of Texas Instruments.
13
THERMAL PAD MECHANICAL DATA
PowerPAD™ PLASTIC SMALL-OUTLINE
PWP (R-PDSO-G28)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third–party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Mailing Address:
Texas Instruments
Post Office Box 655303
Dallas, Texas 75265
Copyright  2002, Texas Instruments Incorporated