NTST40120CT, NTSJ40120CTG, NTSB40120CT-1G, NTSB40120CTG, NTSB40120CTT4G http://onsemi.com Very Low Forward Voltage Trench-based Schottky Rectifier VERY LOW FORWARD VOLTAGE, LOW LEAKAGE SCHOTTKY BARRIER RECTIFIERS 40 AMPERES, 120 VOLTS Exceptionally Low VF = 0.43 V at IF = 5 A Features • Fine Lithography Trench−based Schottky Technology for Very Low • • • • • • PIN CONNECTIONS Forward Voltage and Low Leakage Fast Switching with Exceptional Temperature Stability Low Power Loss and Lower Operating Temperature Higher Efficiency for Achieving Regulatory Compliance Low Thermal Resistance High Surge Capability Pb−Free and Halide−Free Packages are Available 1 2, 4 3 4 4 Typical Applications • Switching Power Supplies including Notebook / Netbook Adapters, • • • • ATX and Flat Panel Display High Frequency and DC−DC Converters Freewheeling and OR−ing diodes Reverse Battery Protection Instrumentation 1 2 3 TO−220AB CASE 221A STYLE 6 12 3 I2PAK CASE 418D STYLE 3 4 Mechanical Characteristics • Case: Epoxy, Molded • Epoxy Meets Flammability Rating UL 94−0 @ 0.125 in • Finish: All External Surfaces Corrosion Resistant and Terminal • Leads are Readily Solderable Lead Temperature for Soldering Purposes: 260°C Maximum for 10 sec 1 2 TO−220FP CASE 221AH D2PAK CASE 418B 3 ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 5 of this data sheet. © Semiconductor Components Industries, LLC, 2013 January, 2013 − Rev. 4 1 Publication Order Number: NTST40120CT/D NTST40120CT, NTSJ40120CTG, NTSB40120CT−1G, NTSB40120CTG, NTSB40120CTT4G MAXIMUM RATINGS Rating Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage Average Rectified Forward Current (Rated VR, TC = 120°C) Per device Per diode Peak Repetitive Forward Current (Rated VR, Square Wave, 20 kHz, TC = 125°C) Per device Per diode Nonrepetitive Peak Surge Current (Surge applied at rated load conditions halfwave, single phase, 60 Hz) Symbol Value Unit VRRM VRWM VR 120 V IF(AV) A 40 20 IFRM A 80 40 IFSM 250 A TJ −40 to +150 °C Storage Temperature Tstg −40 to +150 °C Voltage Rate of Change (Rated VR) dv/dt 10,000 V/ms Operating Junction Temperature Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. THERMAL CHARACTERISTICS Rating Symbol NTST40120CTG, NTSB40120CT−1G NTSB40120CTG NTSJ40120CTG Unit Maximum Thermal Resistance per Diode Junction−to−Case Junction−to−Ambient RqJC RqJA 1.3 70 0.79 46.3 4.0 105 °C/W °C/W ELECTRICAL CHARACTERISTICS (Per Leg unless otherwise noted) Rating Symbol Maximum Instantaneous Forward Voltage (Note 1) (IF = 5 A, TJ = 25°C) (IF = 10 A, TJ = 25°C) (IF = 20 A, TJ = 25°C) vF (IF = 5 A, TJ = 125°C) (IF = 10 A, TJ = 125°C) (IF = 20 A, TJ = 125°C) Maximum Instantaneous Reverse Current (Note 1) (VR = 90 V, TJ = 25°C) (VR = 90 V, TJ = 125°C) IR (Rated dc Voltage, TJ = 25°C) (Rated dc Voltage, TJ = 125°C) 1. Pulse Test: Pulse Width = 300 ms, Duty Cycle v 2.0% http://onsemi.com 2 Typ Max 0.50 0.60 0.78 − − 0.91 0.43 0.53 0.63 − − 0.71 16 16 − − mA mA − 30 500 100 mA mA Unit V NTST40120CT, NTSJ40120CTG, NTSB40120CT−1G, NTSB40120CTG, NTSB40120CTT4G 100 100 TA = 150°C TA = 150°C I R , REVERSE CURRENT (mA) i F , INSTANTANEOUS FORWARD CURRENT (AMPS) TYPICAL CHARACTERISITICS TA = 25°C 10 TA = 125°C 1.0 0.1 10 TA = 125°C 1.0 0.1 0.01 TA = 25°C 0.001 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 vF, INSTANTANEOUS FORWARD VOLTAGE (VOLTS) 20 CJ, JUNCTION CAPACITANCE (pF) 10000 TJ = 25°C 1000 1 10 VR, REVERSE VOLTAGE (VOLTS) 100 RqJC = 1.3°C/W 35 dc 30 25 20 SQUARE WAVE 15 10 5 0 0 20 18 dc PF(AV), AVERAGE FORWARD POWER DISSIPATION (W) IF(AV), AVERAGE FORWARD CURRENT (A) 40 60 80 100 120 TC, CASE TEMPERATURE (°C) SQUARE WAVE 20 40 60 80 100 120 TC, CASE TEMPERATURE (°C) 140 Figure 4. Current Derating per Leg RqJC = 1.3°C/W 0 120 40 Figure 3. Typical Junction Capacitance 80 75 70 65 60 55 50 45 40 35 30 25 20 15 10 5 0 110 Figure 2. Typical Reverse Current IF(AV), AVERAGE FORWARD CURRENT (A) Figure 1. Typical Forward Voltage 100 0.1 50 70 90 100 40 60 80 VR, REVERSE VOLTAGE (VOLTS) 30 SQUARE WAVE 14 12 dc IPK/IAV = 10 10 IPK/IAV = 20 8 6 4 2 0 140 IPK/IAV = 5 16 TA = 150°C 0 2 4 6 8 10 12 14 16 18 20 IF(AV), AVERAGE FORWARD CURRENT (A) Figure 5. Current Derating, Case Figure 6. Forward Power Dissipation http://onsemi.com 3 22 24 NTST40120CT, NTSJ40120CTG, NTSB40120CT−1G, NTSB40120CTG, NTSB40120CTT4G TYPICAL CHARACTERISITICS R(t), TYPICAL TRANSIENT THERMAL RESISTANCE (°C/W) 10 1 50% Duty Cycle 20% 0.1 10% 5% 2% Single Pulse 1% 0.01 0.000001 0.00001 0.0001 0.001 0.01 0.1 t, Pulse Time (sec) 1 10 100 1000 Figure 7. Typical Transient Thermal Response for NTST40120CT and NTSB40120CT−1G R(t), TYPICAL TRANSIENT THERMAL RESISTANCE (°C/W) 10 50% Duty Cycle 1 20% 0.1 10% 5% 2% 1% 0.01 Single Pulse 0.001 0.000001 0.00001 0.0001 0.001 0.01 0.1 1 10 100 1000 100 1000 t, Pulse Time (sec) R(t), TYPICAL TRANSIENT THERMAL RESISTANCE (°C/W) Figure 8. Typical Transient Thermal Response for NTSJ40120CTG 1 50% Duty Cycle 0.1 20% 10% 5% 2% 1% 0.01 0.000001 Single Pulse 0.00001 0.0001 0.001 0.01 0.1 t, Pulse Time (sec) 1 10 Figure 9. Typical Transient Thermal Response for NTSB40120CTG http://onsemi.com 4 NTST40120CT, NTSJ40120CTG, NTSB40120CT−1G, NTSB40120CTG, NTSB40120CTT4G ORDERING INFORMATION Package Shipping NTST40120CTG Device TO−220AB (Pb−Free) 50 Units / Rail NTSJ40120CTG TO−220FP (Halide−Free) 50 Units / Rail NTSB40120CT−1G I2PAK (Pb−Free) 50 Units / Rail NTSB40120CTG D2PAK (Pb−Free) 50 Units / Rail NTSB40120CTT4G D2PAK (Pb−Free) 800 / Tape & Reel MARKING DIAGRAMS AYWW TS40120Cx AKA AYWW TS40120CG AKA AYWW TS40120CG AKA TO−220AB TO−220FP I2PAK A Y WW AKA x G H = Assembly Location = Year = Work Week = Polarity Designator = G or H = Pb−Free Package = Halide−Free Package http://onsemi.com 5 AYWW TS40120CG AKA D2PAK NTST40120CT, NTSJ40120CTG, NTSB40120CT−1G, NTSB40120CTG, NTSB40120CTT4G PACKAGE DIMENSIONS TO−220 CASE 221A−09 ISSUE AF −T− B F T NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION Z DEFINES A ZONE WHERE ALL BODY AND LEAD IRREGULARITIES ARE ALLOWED. SEATING PLANE C S 4 DIM A B C D F G H J K L N Q R S T U V Z A Q U 1 2 3 H K Z L R V J G D N INCHES MIN MAX 0.570 0.620 0.380 0.405 0.160 0.190 0.025 0.035 0.142 0.161 0.095 0.105 0.110 0.155 0.014 0.025 0.500 0.562 0.045 0.060 0.190 0.210 0.100 0.120 0.080 0.110 0.045 0.055 0.235 0.255 0.000 0.050 0.045 ----0.080 STYLE 6: PIN 1. 2. 3. 4. MILLIMETERS MIN MAX 14.48 15.75 9.66 10.28 4.07 4.82 0.64 0.88 3.61 4.09 2.42 2.66 2.80 3.93 0.36 0.64 12.70 14.27 1.15 1.52 4.83 5.33 2.54 3.04 2.04 2.79 1.15 1.39 5.97 6.47 0.00 1.27 1.15 ----2.04 ANODE CATHODE ANODE CATHODE TO−220 FULLPACK, 3−LEAD CASE 221AH ISSUE B A E B P E/2 0.14 M B A M SEATING PLANE A H1 A1 4 Q D C NOTE 3 1 2 3 L L1 3X 3X b2 c b 0.25 M B A M C A2 e http://onsemi.com 6 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. CONTOUR UNCONTROLLED IN THIS AREA. 4. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH AND GATE PROTRUSIONS. MOLD FLASH AND GATE PROTRUSIONS NOT TO EXCEED 0.13 PER SIDE. THESE DIMENSIONS ARE TO BE MEASURED AT OUTERMOST EXTREME OF THE PLASTIC BODY. 5. DIMENSION b2 DOES NOT INCLUDE DAMBAR PROTRUSION. LEAD WIDTH INCLUDING PROTRUSION SHALL NOT EXCEED 2.00. DIM A A1 A2 b b2 c D E e H1 L L1 P Q MILLIMETERS MIN MAX 4.30 4.70 2.50 2.90 2.50 2.70 0.54 0.84 1.10 1.40 0.49 0.79 14.70 15.30 9.70 10.30 2.54 BSC 6.70 7.10 12.70 14.73 --2.80 3.00 3.40 2.80 3.20 NTST40120CT, NTSJ40120CTG, NTSB40120CT−1G, NTSB40120CTG, NTSB40120CTT4G PACKAGE DIMENSIONS D2PAK 3 CASE 418B−04 ISSUE K NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. 418B−01 THRU 418B−03 OBSOLETE, NEW STANDARD 418B−04. C E −B− V W 4 1 2 A S 3 −T− SEATING PLANE DIM A B C D E F G H J K L M N P R S V K J G D 3 PL 0.13 (0.005) W H M T B M VARIABLE CONFIGURATION ZONE N R P U L M INCHES MIN MAX 0.340 0.380 0.380 0.405 0.160 0.190 0.020 0.035 0.045 0.055 0.310 0.350 0.100 BSC 0.080 0.110 0.018 0.025 0.090 0.110 0.052 0.072 0.280 0.320 0.197 REF 0.079 REF 0.039 REF 0.575 0.625 0.045 0.055 L M L M F F F VIEW W−W 1 VIEW W−W 2 VIEW W−W 3 http://onsemi.com 7 MILLIMETERS MIN MAX 8.64 9.65 9.65 10.29 4.06 4.83 0.51 0.89 1.14 1.40 7.87 8.89 2.54 BSC 2.03 2.79 0.46 0.64 2.29 2.79 1.32 1.83 7.11 8.13 5.00 REF 2.00 REF 0.99 REF 14.60 15.88 1.14 1.40 NTST40120CT, NTSJ40120CTG, NTSB40120CT−1G, NTSB40120CTG, NTSB40120CTT4G PACKAGE DIMENSIONS I2PAK (TO−262) CASE 418D ISSUE D C E V −B− NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 4 A W 1 2 DIM A B C D E F G H J K S V W 3 F −T− SEATING PLANE K S J G D 3 PL 0.13 (0.005) M T B H M INCHES MIN MAX 0.335 0.380 0.380 0.406 0.160 0.185 0.026 0.035 0.045 0.055 0.122 REF 0.100 BSC 0.094 0.110 0.013 0.025 0.500 0.562 0.390 REF 0.045 0.070 0.522 0.551 STYLE 3: PIN 1. 2. 3. 4. MILLIMETERS MIN MAX 8.51 9.65 9.65 10.31 4.06 4.70 0.66 0.89 1.14 1.40 3.10 REF 2.54 BSC 2.39 2.79 0.33 0.64 12.70 14.27 9.90 REF 1.14 1.78 13.25 14.00 ANODE CATHODE ANODE CATHODE ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 http://onsemi.com 8 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NTST40120CT/D