Automotive Relays PCB Single Relays Power Relay K (Open – Sealed) n Limiting continuous current 45A Wide voltage range n 24VDC coil versions available n For high current version refer to Power Relay K-S n Typical applications ABS control, blower fans, car alarm, cooling fan, engine control, fuel pump, hazard warning signal, heated front screen, heated rear screen, ignition, lamps front/rear/fog light, interior lights, main switch/supply relay, seat control, seatbelt pretensioner, sun roof, turn signal, valves, window lifter, wiper control. Contact Data Typical applications Resistive/inductive Resistive/inductive Indicator lamps Headlights, Headlights loads loads capacitive loads capacitive loads Contact arrangement 1 form A, 1 NO 1 form C, 1 CO 1 form A, 1 NO 1 form A, 1 NO 1 form C, 1 CO Rated voltage 12VDC12VDC12VDC12VDC12VDC A/B (NO/NC)A/B (NO/NC) Rated current 45A45/30A30A 40A40/25A Limiting continuous current 23°C 45A45/30A30A 40A40/25A 85°C 30A30/25A25A 25A25/20A 1) Limiting making current 100A 100/30A 120A3) 180A180/60A Limiting breaking current2) 60A60/30A60A 60A60/30A Contact material AgNi0.15 AgNi0.15 AgSnO2AgSnO2AgSnO2 Min. recommended contact load 1A at 5VDC4) Initial voltage drop, at 10A, typ./max. 20/300mV Operate/release time typ. 5/3ms5) Electrical endurance >2x105 ops. >2x105 ops. >2.2x106 ops. >105 ops. >105 ops. at 13.5VDC, 40A at 13.5VDC, 40A up to 8x21W up to 4x60W up to 4x60W Mechanical endurance, DC coil >107 ops. 1) 2) 3) 4) 5) The values apply to a resistive or inductive load with suitable spark suppression and at maximum 13.5VDC for 12VDC or 27VDC for 24VDC load voltages. For a load current duration of maximum 3s for a make/break ratio of 1:10. Corresponds to a peak inrush current on initial actuation (cold filament). See chapter Diagnostics of Relays in our Application Notes or consult the internet at http://relays.te.com/appnotes/ For unsuppressed relay coil. A low resistive suppression device in parallel to the relay coil increases the release time and reduces the lifetime caused by increased erosion and/or higher risk of contact tack welding. Max. DC load breaking capacity TE0556-E Load limit curve 1: arc extinguishes, during transit time (changeover contact). Load limit curve 2: safe shutdown, no stationary arc (make contact). Load limit curves measured with low inductive resistors verified for 1000 switching events. 06-2011, Rev. 0611 www.te.com © 2011 Tyco Electronics Corporation, a TE Connectivity Ltd. company. Datasheets and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section. Datasheets and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions Datasheets, product data, ‘Definitions’ section, application notes and all specifications are subject to change. 1 Automotive Relays PCB Single Relays Power Coil Data Rated coil voltage Relay K (Open – Sealed) (Continued) Insulation Data 12VDC / 24VDC Coil versions, DC coil Coil Rated Operate Release Coil Rated coil codevoltagevoltagevoltage resistancepower VDCVDCVDC Ω±10%W 00112 6.91.290 1.6 0222414.1 2.4362 1.6 All figures are given for coil without pre-energization, at ambient temperature +23°C. Other coils on request. Coil operating range TE0555-6 Does not take into account the temperature rise due to the contact current E = pre-energization Initial dielectric strength between open contacts between contact and coil 500VACrms 500VACrms Other Data EU RoHS/ELV compliance compliant Ambient temperature, DC coil -40 to +105°C6) Climatic cycling with condensation, EN ISO 6988 3 cycles, storage 8/16h Temperature cycling (shock), IEC 60068-2-14, Na 20 cycles, -40/+85°C (dwell time 1h) Damp heat cyclic, IEC 60068-2-30, Db, Variant 1 6 cycles, upper air temperature 55°C Damp heat constant, IEC 60068-2-3, method Ca 56 days, upper air temperature 55°C Degree of protection, IEC 61810 RT 0/II – open version RT III – immersion cleanable version Corrosive gas, IEC 60068-2-42 10 days IEC 60068-2-43 10 days Vibration resistance (functional), Does notIEC take60068-2-6 into account (sine pulse form), the temperature rise due to acceleration, acc. to position 10 to 200Hz, 20 to 40g7) the contact current Shock resistance (functional), E = pre-energization IEC 60068-2-27 (half sine form single pulses), acceleration, acc. to position 8ms 30g7) Terminal type PCB Weight sealed version approx. 22g (0.77oz) open version approx. 19g (0.67oz) Solderability (aging 3: 4h/155°C) for leaded process (Tm = 183°C), for Pb-free process (Tm = 217°C), IEC 60068-2-20 Ta, method 1, hot dip 5s, 215°C Storage conditions according IEC 600688 8) Packaging unit sealed version 300 pcs. open version 500 pcs. 6) See coil operating range DC. 7) No change in the switching state >10μs. 8) For general storage and processing recommendations please refer to our Application Notes and especially to Storage in the Definitions or at http://relays.te.com/appnotes/ Terminal Assignment (Open and Sealed Version) Bottom view on solder pins 1 form C, 1 CO 1 form A, 1 NO TE1091-B1 TE1086-A1 06-2011, Rev. 0611 www.te.com © 2011 Tyco Electronics Corporation, a TE Connectivity Ltd. company. Datasheets and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section. *) Terminal 4 to be bridged 2 Datasheets and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions Datasheets, product data, ‘Definitions’ section, application notes and all specifications are subject to change. Automotive Relays PCB Single Relays Power Relay K (Open – Sealed) (Continued) Dimensions Power Relay K open version Power Relay K sealed version 26.1 ±0.4 18.6 ±0.65 23.3 ±0.7 8.5 ±0.2 21.1 ±0.4 18.0 ±0.5 9.2 ±0.4 18.9 ±0.3 2.4 ±0.8 3.0 ±0.5 *) *) additional tin tops max. 1.5 mm Assembly and positioning aid 2.5 ±0.4 3.4 ±0.1 2.5 – 3.0 Terminals tinned TE2179-42 3.4 ±0.1 21.2 ±0.3 3.0 ±0.5 *) 2.5 – 3.0 0.55 ±0.25 TE0579-I2 Terminals tinned *) additional tin tops max. 1.5 mm Mounting Hole Layout Bottom view on solder pins Power Relay K open version Power Relay K sealed version 16.0 ±0.3 16.0 ±0.3 10.2 ±0.2 10.2 ±0.2 6.0 ±0.2 3.3 ±0.1 1.3 +0.1 2.4 6.0 ±0.2 1.0 +0.05 ø 1.3 +0.1 ø 2.3 +0.1 5.4 2.2 ±0.1 12.1 ±0.1 ø 2.1 +0.1 ø 2.3 +0.1 3.4 ±0.6 6.6 ±0.3 12.1 ±0.1 2.2 ±0.1 3.3 ±0.1 ø 2.1 +0.1 1.0 +0.05 ø 2.3 +0.1 ø 2.3 +0.1 ø 2.3 +0.1 2.3 ±0.2 13.3 ±0.2 TE0575-K2 ø 2.3 +0.1 2.3 ±0.2 13.3 ±0.2 TE0580-L2 06-2011, Rev. 0611 www.te.com © 2011 Tyco Electronics Corporation, a TE Connectivity Ltd. company. Datasheets and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section. Datasheets and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions Datasheets, product data, ‘Definitions’ section, application notes and all specifications are subject to change. 3 Automotive Relays PCB Single Relays Power Relay K (Open – Sealed) (Continued) Product code structure Typical product code V23076-A 1 022-C 13 3 Type V23076 Power Relay K, sealed V23133 Power Relay K, open Terminal A PCB Design 1 Single relay Coil 001 12VDC Contact type C Single contact Contact material 13 AgNi0.15 15 AgSnO2 (Special) Contact arrangement 2 1 form A, 1 NO Product code Terminal/Encl. 3 Single relay 022 24VDC D Single contact 14 AgSnO2 3 1 form C, 1 CO Design Coil Contact Cont. material Arrangement Part number V23076-A1001-C133 PCB, sealed Single relay 12VDC Single AgNi0.15 1 form C, CO 1393277-4 V23076-A1001-D143 AgSnO21393277-6 V23076-A3001-C132 AgNi0.15 1 form A, NO 1-1393277-4 V23076-A3001-D142 AgSnO21-1393277-7 V23076-A3001-D1521) AgSnO2 special 1-1414175-0 V23076-A1022-C133 24VDC AgNi0.15 1 form C, CO 1393277-8 V23076-A1022-D143 AgSnO21393277-9 V23076-A3022-C132 AgNi0.15 1 form A, NO 1-1393277-8 V23076-A3022-D142 AgSnO21-1393277-9 V23133-A1001-C133 PCB, open 12VDC AgNi0.15 1 form C, CO 1393278-7 V23133-A1001-D143 AgSnO21-1393278-3 V23133-A3001-C132 AgNi0.15 1 form A, NO 5-1393278-7 V23133-A3001-D142 AgSnO25-1393278-9 V23133-A3001-D1521) AgSnO2 special 1-1414173-0 V23133-A1022-C133 24VDC AgNi0.15 1 form C, CO 3-1393278-7 V23133-A1022-D143 AgSnO23-1393278-9 V23133-A3022-C132 AgNi0.15 1 form A, NO 7-1393278-1 V23133-A3022-D142 AgSnO27-1393278-2 V23133-A3022-D1521) AgSnO2 special 1-1414174-0 1) For indicator lamps. 4 06-2011, Rev. 0611 www.te.com © 2011 Tyco Electronics Corporation, a TE Connectivity Ltd. company. Datasheets and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section. Datasheets and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions Datasheets, product data, ‘Definitions’ section, application notes and all specifications are subject to change. Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: TE Connectivity: V23076A1022C133