STMICROELECTRONICS BTA10

BTA10-600GP
10 A Triac
Features
■
Low IH:
– 13 mA max
■
High surge current:
– ITSM = 120 A
A2
G
A1
■
IGT specified in four quadrants
■
Insulating voltage:
– 2500 V(RMS) (UL Recognized: E81734)
Description
A1
A2
The BTA10-600GP uses high performance, glass
passivated chips.
G
TO-220AB
The insulated TO-220AB package, the high surge
current and low holding current make this product
well adapted to CFL and LED dimmer
applications.
September 2011
Doc ID 022222 Rev 1
1/7
www.st.com
7
Characteristics
BTA10-600GP
1
Characteristics
Table 1.
Absolute ratings (limiting values)
Symbol
Parameter
Unit
600
V
A
VDRM
VRRM
Repetitive peak off-state voltage Tj = 125° C
IT(RMS)
RMS on-state current (360° conduction angle)
Tc = 90° C
10
Non repetitive surge peak on-state current
(Tj initial = 25° C)
tp = 8.3 ms
126
tp = 10 ms
120
I²t Value for fusing
tp = 10 ms
72
Repetitive
F = 50 Hz
10
Non repetitive
50
ITSM
I2t
dI/dt
Tstg
Tj
Table 2.
Critical rate of rise of on-state current
IG = 500 mA diG/dt = 1 A/µs
Storage junction temperature range
Operating junction temperature range
A
A2s
A/µs
-40 to +150
-40 to +125
°C
Value
Unit
Electrical characteristics
Symbol
Test conditions
Quadrant
I - II- III
MAX
25
IV
MAX
100
Tj = 25° C
I - II - III - IV
MAX
1.5
V
VD = VDRM RL = 3.3 kΩ
Tj = 110° C
I - II - III - IV
MIN
0.2
V
tgt
VD = VDRM IG = 500 mA dIG/dt = 3 A/µs
Tj = 25° C
I - II - III - IV
TYP
2
µs
IL
IG = 1.2 IGT
Tj = 25° C
IT = 100 mA gate open
Tj = 25° C
MAX
13
mA
ITM = 14 A tp = 380 µs
Tj = 25° C
MAX
1.5
V
Tj = 25° C
MAX
0.01
Tj = 110° C
MAX
0.5
MIN
30
TYP
100
MIN
1
TYP
10
IGT (1)
VD = 12 V (DC)
RL = 33 Ω
Tj = 25° C
VGT
VD = 12 V (DC)
RL = 33 Ω
VGD
mA
I - II - III
IH (1)
VTM
(1)
IDRM
IRRM
dV/dt (1)
VDRM = VRRM
Linear slope up to VD = 67% VDRM
gate open
(dV/dt)c (1) (dI/dt)c = 2.2 A/ms
Tj = 110° C
Tj = 110° C
1. For either polarity of electrode A2 voltage with reference to electrode A1.
2/7
Value
Doc ID 022222 Rev 1
20
TYP
IV
mA
40
mA
V/µs
V/µs
BTA10-600GP
Table 3.
Characteristics
Gate characteristics (maximum values)
Symbol
PG(AV)
Parameter
Value
Unit
1
W
Average gate power dissipation
PGM
Peak gate power dissipation
tp = 20 µs
10
W
IGM
Peak gate current
tp = 20 µs
4
A
VGM
Peak positive gate voltage
tp = 20 µs
16
V
Table 4.
Thermal resistances
Symbol
Rth(j-a)
Parameter
Value
Junction to ambient
60
Rth(j-c) DC
Junction to case for DC
4
Rth(j-c) AC
Junction to case for 360° conduction angle (F = 50 Hz)
3
Figure 1.
Maximum rms power dissipation
versus rms on-state current
Figure 2.
Unit
° C/W
Maximum rms power dissipation
and maximum allowable
temperatures (Tamb and Tcase)
For different thermal resistances
heatsink + contact
F = 50 Hz, curves
are cut off by
(dI/dt)c limitation
Figure 3.
On-state rms current versus case
temperature
Figure 4.
Relative variation of thermal
impedance versus pulse duration
Zth/Rth
1
Zth(j-c)
0.1
Zth(j-a)
tp(s)
0.01
1E-3
Doc ID 022222 Rev 1
1E-2
1E-1
1E+0
1E+1
1E+2 5E+2
3/7
Characteristics
BTA10-600GP
Figure 5.
Relative variation of gate trigger
Figure 6.
current and holding current versus
junction temperature
Non repetitive surge peak on-state
current versus number of cycles
Figure 7.
Non repetitive surge peak on-state Figure 8.
current and corresponding value of
I2t
On-state characteristics (maximum
values)
Sinusoidal pulse width tp < 10 ms
4/7
Doc ID 022222 Rev 1
BTA10-600GP
2
Package information
Package information
●
Epoxy meets UL94,V0
●
Cooling method: Conduction
●
Recommended torque value: 0.4 to 0.6 N·m
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.
Table 5.
TO-220AB dimensions
Dimensions
Ref.
Millimeters
Min.
A
15.20
a1
C
B
ØI
Typ.
Max.
Inches
Min.
Typ.
15.90 0.598
3.75
Max.
0.625
0.147
a2
13.00
14.00 0.511
0.551
B
10.00
10.40 0.393
0.409
b1
0.61
0.88
0.024
0.034
b2
1.23
1.32
0.048
0.051
C
4.40
4.60
0.173
0.181
c1
0.49
0.70
0.019
0.027
c2
2.40
2.72
0.094
0.107
e
2.40
2.70
0.094
0.106
F
6.20
6.60
0.244
0.259
ØI
3.75
3.85
0.147
0.151
I4
15.80 16.40 16.80 0.622 0.646 0.661
L
2.65
2.95
0.104
0.116
l2
1.14
1.70
0.044
0.066
l3
1.14
1.70
0.044
0.066
b2
L
F
A
I4
l3
c2
a1
l2
a2
M
b1
e
c1
M
Doc ID 022222 Rev 1
2.60
0.102
5/7
Ordering information
3
Ordering information
Table 6.
4
Ordering information
Order code
Marking
Package
Weight
BTA10-600GPRG
BTA10 600GP
TO-220AB
2.3 g
Revision history
Table 7.
6/7
BTA10-600GP
Document revision history
Date
Revision
13-Sep-2011
1
Changes
Initial release
Doc ID 022222 Rev 1
Base qty Delivery mode
50
Tube
BTA10-600GP
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2011 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
Doc ID 022222 Rev 1
7/7