® PCM67P/U PCM69AP/AU Advanced 1-Bit BiCMOS Dual 18-Bit DIGITAL-TO-ANALOG CONVERTER FEATURES DESCRIPTION ● 18-BIT RESOLUTION DUAL AUDIO DAC ● EXCELLENT THD PERFORMANCE: 0.0025% (–92dB) at F/S, K Grade 1.0% (–40dB) at –60dB, K Grade The PCM67 and PCM69A dual 18-bit DAC are low cost, dual output 18-bit BiCMOS digital-to-analog converters utilizing a novel architecture to achieve excellent low level performance. ● HIGH S/N RATIO: 110dB typ (IHF-A) ● DUAL, CO-PHASE By combining a conventional thin-film R-2R ladder DAC, a digital offset technique with analog correction and an advanced one-bit DAC using first order noise shaping technique, the PCM67 and PCM69A achieve high resolution, minimal glitch, and low zero-crossing distortion. ● SINGLE SUPPLY +5V OPERATION ● LOW POWER: 75mW typical ● CAPABLE OF 16X OVERSAMPLING ● AVAILABLE IN SPACE SAVING 16-PIN DIP OR 20-PIN SOIC ● OPERATING TEMP RANGE: –25°C to +85°C ● EXTREMELY LOW GLITCH ENERGY PCM67 digital offset occurs at bit 9, making it ideal for high-performance CD players. PCM69A digital offset occurs at bit 4, making it an excellent choice for digital musical instruments and audio DSP. Both PCM67 and PCM69A operate from a single +5V supply. The low power consumption and small size (16pin PDIP or 20-pin SOIC) make these converters ideal for a variety of digital audio applications. 10-Bit DAC plus Analog Correction Reference Servo Analog Output Lch Advanced 1-Bit DAC 10-Bit DAC plus Analog Correction Digital Signal In Input Interface Buffer VCOM Lch Buffer VCOM Rch Analog Output Rch Advanced 1-Bit DAC SBAS024 International Airport Industrial Park • Mailing Address: PO Box 11400 Tel: (520) 746-1111 • Twx: 910-952-1111 • Cable: BBRCORP • • Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd. • Tucson, AZ 85706 Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132 © 1992 Burr-Brown Corporation PDS-1168A Printed in U.S.A. August, 1993 SPECIFICATIONS ELECTRICAL All specifications at +25°C and +VA, +VD = +5V unless otherwise noted PCM67/69A PARAMETER CONDITIONS MIN TYP MAX UNITS RESOLUTION 18 Bits DYNAMIC RANGE, THD+N at –60dB Referred to Full Scale 106 dB DIGITAL INPUT Logic Family Logic Level: VIH VIL Data Format Input System Clock Frequency TTL/CMOS Compatible IIH = ±5µA IIL = ±5µA +2 0 +VD 0.8 Serial, MSB First, BTC(1) 16.9344 MHz TOTAL HARMONIC DISTORTION + N(2,3,4) PCM67P/69AP, PCM67U/69AU f = 991Hz (0dB) f = 991Hz (–20dB) f = 991Hz (–60dB) fS = 352.8kHz fS = 352.8kHz fS = 352.8kHz –86 –68 –40 –82 PCM67P-J/69AP-J, PCM67U-J/69AU-J f = 991Hz (0dB) f = 991Hz (–20dB) f = 991Hz (–60dB) fS = 352.8kHz fS = 352.8kHz fS = 352.8kHz –91 –72 –46 –88 PCM67P-K/69AP-K, PCM67U-K/69AU-K f = 991Hz (0dB) f = 991Hz (–20dB) f = 991Hz (–60dB) fS = 352.8kHz fS = 352.8kHz fS = 352.8kHz –95 –74 –46 –92 (f = 1kHz) 106 at –90dB Signal Level ±1 ±3 ±1 95 1 CHANNEL SEPARATION ACCURACY Level Linearity Gain Error Gain Mismatch, Channel-to-Channel Gain Drift Warm-up Time IDLE CHANNEL SNR(5) 0°C to +70°C 20Hz to 40kHz at BPZ(6) ANALOG OUTPUT Output Range (±3%) Output Impedance (±30%) VCOM Glitch Energy 3.35 POWER SUPPLY REQUIREMENTS, System Clock = 16.9344MHz +VA, +VD Supply Voltage Range +VA = +VD +IA, +ID Combined Supply Current +VA, +VD = +5V Power Dissipation +VA, +VD = +5V +4.75 TEMPERATURE RANGE Operating Storage V V –34 –40 –40 dB dB dB dB dB dB dB dB dB dB ±10 ±5 dB % % ppm/°C Minute 110 dB 1.2 1.8 3.50 No Glitch Around Zero 3.65 mA kΩ V +5.25 20 105 V mA mW +85 +100 °C °C +5.00 15 75 –25 –55 NOTES: (1) Binary Two’s Complement coding. (2) Ratio of (DistortionRMS + NoiseRMS)/SignalRMS. (3) D/A converter output frequency/signal level (both left and right channels are “on”). (4) D/A converter sample frequency (8 x 44.1kHz; 8X oversampling per channel). (5) Ratio of NoiseRMS/SignalRMS. Measured using a 40kHz 3rd-order GIC (Generalized Immittance Converter) filter and an A-weighted filter. (6) Bipolar Zero. USA OEM PRICES The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems. ® PCM67/69A 2 PIN ASSIGNMENTS PCM67P ABSOLUTE MAXIMUM RATINGS PCM67U PCM69AP PCM69AU 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 DESCRIPTION MNEMONIC +5V Analog Supply Voltage Left Voltage Common No Connection Left Current Output (0 to 1.2mA) Servo Decoupling Capacitor Reference Decoupling Capacitor Right Current Output (0 to 1.2mA) No Connection Right Voltage Common Analog Common Digital Common Mode Control 2 Right Data Input Bit Clock System Clock Word Clock Left Data Input Mode Control 3 Mode Control 1 +5V Digital Supply Voltage +VA LVCOM NC LIOUT SRVCAP REFCAP RIOUT NC RVCOM ACOM DCOM MC2 RDATA BTCK SYSCK WDCK LDATA MC3 MC1 +VD +VA, +VD to ACOM, DCOM ................................................... 0V to +6.5V ACOM to DCOM ............................................................................... ±0.5V Digital Inputs to DCOM ............................................ –0.3V to +VD + 0.3V Power Dissipation ................ 300mW (U Package), 500mW (P Package) Lead Temperature, (soldering, 10s) .............................................. +260°C Max Junction Temperature ............................................................ +165°C NOTE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. Exposure to absolute maximum conditions for extended periods may affect device reliability. ELECTROSTATIC DISCHARGE SENSITIVITY Electrostatic discharge can cause damage ranging from performance degradation to complete device failure. Burr-Brown Corporation recommends that all integrated circuits be handled and stored using appropriate ESD protection methods. PACKAGE INFORMATION MODEL PCM67P/69AP PCM67U/69AU PACKAGE PACKAGE DRAWING NUMBER(1) 16-Pin Plastic DIP 20-Pin SOIC 180 248 NOTE: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix D of Burr-Brown IC Data Book. ® 3 PCM67/69A PIN CONFIGURATION — PCM67P/69AP (16-Pin DIP) Data-L WDCK SYS CLOCK BCK Data-R 1µF 16 15 14 13 12 11 10 9 4 5 6 7 8 PCM67P/69AP +VCC (+5V) 1 2 3 10µF 3.3µF 3.3µF RNF RNF Lch OUT 10µF 10µF Rch OUT PIN CONFIGURATION — PCM67U/69AU (20-Pin SOIC) Data-L WDCK SYS CLOCK BCK Data-R 1µF 20 19 18 17 16 15 14 13 12 11 4 5 6 7 8 9 10 PCM67U/69AU +VCC (+5V) 1 2 3 10µF 3.3µF 3.3µF RNF 10µF Lch OUT ® PCM67/69A RNF 4 10µF Rch OUT TYPICAL PERFORMANCE CURVES All specifications at +25°C and VCC = +5.0V unless otherwise noted. THD vs POWER SUPPLY VOLTAGE GAIN ERROR / VCOM vs POWER SUPPLY 1.0% 0.01% 3 –60dB 2 F/S 0.2% 0.002% 1 Gain Error 3.60 VCOM (V) THD (–60dB) Gain Error (%) 0.5% 0.005% THD (F/S) 3.70 0 –1 3.50 VCOM –2 0.001% 4.75 –3 4.75 0.1% 5.25 5.0 3.40 5.25 5.0 VCC (V) VCC (V) GAIN ERROR / VCOM vs TEMPERATURE THD vs TEMPERATURE 0.01% 3 1.0% 3.70 –60dB 2 F/S 0.002% 1 3.60 VCOM (V) THD (–60dB) Gain Error (%) 0.5% THD (F/S) 0.005% 0 –1 3.50 0.2% –2 0.001% –25 0 25 50 85 –3 0.1% 100 –25 0 25 50 75 85 3.40 100 Temperature (%) Temperature (°C) THD vs SYSTEM CLOCK FREQUENCY CHANNEL SEPARATION vs SIGNAL FREQUENCY 0.01% 1.0% 115 fs = 44.1kHz –60dB 110 THD (–60dB) Separation (dB) 0.5% THD (F/S) 0.005% F/S 0.002% 0.2% 0.001% 100 95 100 0.1% 384 192 96 105 48 500 1k 2k 4k 8k 16k … 128k f (Hz) fs (Hz) ® 5 PCM67/69A DISCUSSION OF SPECIFICATIONS VOUT = 1.2mA • RNF The PCM67 and PCM69A are specified to provide critical performance criteria for a variety of applications. The accuracy of a D/A converter is described by the transfer function shown in Figure 1. VOUT RNF VCOM 1.2mA IOUT Digital In +FSR 011...11 VOUT VCOM (3.5V) Gain Error FIGURE 2. I/V Amplifier Circuit. 000...00 S/N RATIO S/N ratio is defined as the ratio of full scale output and no input noise level at BPZ point. The PCM67/69A is specified at 110dB typical with “IHF-A” filter. Analog Out 111...11 BPZ BPZ – 1LSB 100...00 –FSR (V = 3.5V) LEVEL LINEARITY ERROR Level linearity error is defined as the deviation of actual analog output level from digital input level. PCM67/69A is specified at 1dB typical at –90dB output level. The 0.5LSB quantization error at –90dB of 16-bit conversion is equal to +1.94dB, –2.5dB. COM FIGURE 1. Transfer Performance. DIGITAL INPUT CODE The PCM67/69A accepts Binary Two’s Complement (BTC) digital input code (MSB FIRST).The relationship of digital input to analog output is shown in Table 1. DIGITAL INPUT ANALOG OUTPUT (VOLTAGE) ANALOG OUTPUT (CURRENT) 7FFFFF (HEX) 00003F (HEX) FFFFFF (HEX) 80003F (HEX) +FSR BPZ BPZ – 1LSB –FSR –1.2mA –0.6mA –0.59995mA 0mA TOTAL HARMONIC DISTORTION THD is a key parameter in audio applications, THD is a measure of the magnitude and distribution of the linearity error, differential linearity error, and noise, as well as quantization error. To be useful, THD should be specified for both high level and low level input signals. This error is unadjustable and is the most meaningful indicator of D/A converter accuracy for audio applications. THD is defined as the ratio of the square root of the sum of the squares of the values of the harmonics to the value of the fundamental input frequency and is expressed in percent or dB. The rms value of the PCM67/69A error referred to the input can be shown to be TABLE I. Digital Code and Analog Out. GAIN ERROR AND GAIN MISMATCH, CHANNEL-TO-CHANNEL Gain error is defined as deviation of the output current span from the ideal span of 1.2mA (FSR) on each channel. Gain error of PCM67/69A is typically ±3% of FSR. ε rms = Gain mismatch, channel-to-channel is defined as the difference in gain error between the left channel and right channel. n ∑ E L (i ) + E Q (i ) 2 (1) i=1 where n is the number of samples in one cycle of any given sine wave, EL(i) is the linearity error of the PCM67 or PCM69A at each sampling point. THD can then be expressed as THE RELATIONSHIP OF VCOM AND I/V OUT The output current range of PCM67 and PCM69A is 0mA to 1.2mA as shown in Table 1. n In the typical application, the non-inverting input of the external I/V op amp is connected to the VCOM pin of PCM67 and PCM69A. Accordingly, the output voltage level at FSR after I/V conversion is VCOM voltage (+3.5V) as shown in Figure 2. THD = ε rms Er ms 2 1 n ∑ EL (i ) + EQ (i ) = i =1 E rms where Erms is the rms signal-voltage level. ® PCM67/69A 1 n 6 × 100% (2) This expression indicates that, in general, there is a correlation between the THD and the square root of the sum of the squares of the linearity errors at each digital word of interest. However, this expression does not mean that the worst-case linearity error of the D/A is directly correlated to THD. The PCM67/69A accepts TTL compatible logic input levels. The data format of the PCM67/69A is BTC with the most significant bit (MSB) being first in the serial input bit stream. tSL tSH For PCM67 and PCM69A the test period is set at an 8X oversampling rate (352.8kHz = 44.1kHz • 8), which is the typical sample rate for CD player applications. SYS Clock The test signal frequency is 991Hz and the amplitude of the signal level is F/S (0dB), and –60dB down from F/S. Data tDH All THD tests are performed without a deglitcher circuit and without a 20kHz low pass filter. LSB tCH tSH: tSL: tDW: tDSU: tDHO: tCH: tCL: tCW: tWC: tWH: tWL: The user can choose either model for their application. Table II shows the different SYSCLK options. PCM67 PCM69A 384Fs 192Fs, 96Fs WDCK tn1 SYSCLK Refer to Figure 3 for graphical relationships of these signals. The setup and hold timing relationships for these signals are shown in Figure 4. bit17 LSB MSB bit2 bit17 LSB L-ch Data MSB bit2 bit17 LSB MSB bit2 bit17 LSB SYS Clock High Pulse Width : 15ns, min SYS Clock Low Pulse Width : 15ns, min Data Valid Time : 20ns, min Data Setup Time : 10ns, min Data Hold Time : 5ns, min Bit Clock High Pulse Width : 15ns, min Bit Clock Low Pulse Width : 15ns, min WD Clock Fall Time From Bit Clock Rise : 10ns, min Bit Clock Rise Time From WD Clock Fall : 15ns, min WD Clock High Pulse Width : 1 SYS Clock Cycle, min WD Clock Low Pulse Width : 1 SYS Clock Cycle, min PCM69A timing is similar to PCM67 except that PCM69A is capable of operating from any system clock up to 384Fs. For synchronized operation, PCM69A system clock and WDCK timing must be as shown in Figure 5. LOGIC TIMING The serial data bit transfers are triggered on positive bit clock (BCK) edges. The serial-to-parallel data transfer to the DAC occurs on the falling edge of Word Clock (WDCK). The change in the output of the DAC coincides with the falling edge of WDCK. bit2 tWL TIMING OF PCM69A TABLE II. System Clock Requirements. MSB tWC FIGURE 4. Timing Specification. Any Clock (with timing condition) Examples: 384Fs, 300Fs, 256Fs, 200Fs, 90Fs R-ch Data tCW tWH The PCM69A is capable of any system clock up from 48Fs to 384Fs such as 384Fs, 256Fs, 100Fs with condition for timing as described in “Timing of PCM69A” in Figure 5. OTHER CAPABLE SYSCLK tCL WD Clock The PCM67 is capable of only a 384Fs corollary system clock frequency such as 192Fs, 96Fs (24 times word rate or integer multiple of 24). BASIC SYSCLK tDHO Bit Clock SYSTEM CLOCK REQUIREMENTS The PCM67 and PCM69A need a system clock for the one-bit noise shaping DAC operation. MODEL tDSU tn2 SYSCLK tn1: WDCK Fall Delay From Rise of SYSCLK : min 10ns tn2: SYSCLK Rise Delay From Fall of WDCK : min 20ns FIGURE 5. Timing of PCM69A for SYSCLK and WDCK. Bit Clock WD Clock SYS Clock 1 WDCK FIGURE 3. Timing Diagram. ® 7 PCM67/69A INSTALLATION SHIFT OF I/V OUT VOLTAGE If the user requires a bipolar voltage output centered around 0V or one-half of VCC, the output can be shifted by adding an offset current on the inverting point of the I/V op amp as shown in Figure 6. POWER SUPPLIES Refer to “Pin Configuration” diagram for proper connection of the PCM67/69A. The PCM67/69A requires only a +5V supply. Both analog and digital supplies should be tied together at a single point, as no real advantage is gained by using separate supplies. It is more important that both these supplies be as “clean” as possible to reduce coupling of supply noise to the output. +VCC (+5V) FILTER CAPACITOR REQUIREMENTS As shown in the “Pin Configuration” diagram, various sizes of decoupling capacitors can be used with no special tolerances required. All capacitors should be as close to the appropriate pins of the PCM67/69A as possible to reduce noise pickup from surrounding circuitry. VOUT VCOM VCOM (+3.5V) VCC 2 or 0V C2 6V 0V Note: R1 and C1 are noise de-coupling circuits from noise on +VCC power supply line. FIGURE 7. Useful Application Circuit for Shift of I/V Out Voltage. INTERFACE CONTROL FUNCTION Both the PCM67 and PCM69A (SOIC package type) are capable of 16-bit L/R serial input and 20-bit L/R parallel input as shown in Table 3. VO VS VSHT +VCC RNF ROS + 10µF ~ 100µF The best suitable value for the capacitors should be determined by the user’s actual application board. VO C1 RNF 5kΩ R2 330Ω IOUT The value of these capacitors is influenced by actual board layout design and noise from power supplies and other digital input lines. VO 2 + 10µF ~ 100µF A power supply decoupling capacitor should be used near the analog supply pin to maximize power supply rejection, as shown in Figure 6, regardless of how good the supplies are. Both commons should be connected to an analog ground plane as close to the PCM67/69A as possible. VCOM + R1 820Ω IOS IOUT VOUT VCOM (3.5V) MC1 MC2 MC3 DATA-R 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 1 1 1 1 1 0 1 0 0 1 0 1 X X X X INPUT FORMAT 16-Bit 16-Bit 18-Bit 18-Bit 20-Bit 20-Bit 18-Bit 18-Bit L/R L/R L/R L/R L/R L/R L/R L/R Serial(1) Serial(1) Serial(1) Serial(1) Parallel Parallel Parallel Parallel LR L R LR L R LR L R LR L R WDCK WDCK WDCK WDCK [WDCK Invert] [WDCK Invert] NOTE: (1) Data input to Data-Lch (Pin 17) for L/R serial format. TABLE III. Interface Control Function of SOIC. In case of shift to ±3V swing, 0V center V 6V RNF = OUT = = 5kΩ 1.2mA 1.2mA PCM67P and PCM69AP (DIP package) have only 18-bit L/R serial input function as shown in Table 4. –FSR±(VS) = –3V after offset addition, shift voltage VSHT is given by VSHT = VCOM + 3V = 3.5 + 3 = 6.5V Offset Current IOS is given by VSHT 6.5V IOS = = = 1.3mA RNF 5kΩ Offset Resistor ROS is given by V – VCOM ROS = CC = 5 – 3.5V = 1.15kΩ 1.3mA IOS DATA-R INPUT FORMAT 0 0 1 0 1 X 18-Bit L/R Serial 18-Bit L/R Serial 18-Bit L/R Parallel L R L R WDCK L R L R WDCK TABLE IV. Interface Control Function of DIP. FIGURE 6. Shift of I/V Out Voltage. ® PCM67/69A MC1 8 DIGITAL FILTER INTERFACE 16-Bit L/R Serial — 1 18-Bit L/R Parallel +VDD SM5840 PCM67U/69AU PCM67U/69AU 11 DGND 11 DGND 12 MC2 12 MC2 CXD2551 DOR 13 Data R-ch 14 BCK BCK0 16 WDCK DOL 17 Data L-ch Data L-ch 15 SYSCLK WDCK0 16 WDCK LRCK0 14 BCK XTi 15 SYSCLK X0 or X1 13 Data R-ch BCK0 17 Data L-ch 18 MC3 18 MC3 4FS, 16-Bit Mode 19 MC1 19 MC1 20 +VDD 20 +VDD 18-Bit Mode FIGURE 8. Using Sony CXD2551. FIGURE 10. Using NPC SM5840. 16-Bit L/R Serial — 2 SM5807 20-Bit L/R Parallel PCM67U/69AU DF1700 11 DGND 12 MC2 12 MC2 14 BCK XTi 16 WDCK 15 SYSCLK WDCK0 17 Data L-ch DOUT 13 Data R-ch BCK0 15 SYSCLK LRC0 SOMD = H DOR 14 BCK XTi PCM67U/69AU 11 DGND 13 Data R-ch BCK0 –VDD 16 WDCK DOL 17 Data L-ch 18 MC3 18 MC3 19 MC1 19 MC1 20 +VDD 20 +VDD +VDD 20-Bit Mode +VDD FIGURE 11. Using Burr-Brown DF1700. FIGURE 9. Using NPC SM5807. ® 9 PCM67/69A THEORY OF OPERATION Digital converters in audio systems have traditionally utilized a laser-trimmed, current-source DAC architecture. Unfortunately, this type of technology suffers from the problems inherent in switching widely varying current levels. Design improvements have helped, but DACs of this type still exhibit low-level nonlinearity due to errors at the major carry. weight of bit n is switched in to compensate. This offset comes from a one-bit DAC which has also been trimmed to 18-bit linearity. While this technique doesn’t remove the major carry error completely, the “glitch” is only present in higher amplitude signals where it is much less audible. As for the one-bit DAC, a number of problems with this architecture are also reduced: the DAC is designed to operate from the system clock, thus eliminating the need for a separate clock; the lower quantizing level of the DAC make it less sensitive to clock jitter; and output filtering requirements are reduced because “out-of-band noise” has smaller amplitude, is “farther-out,” and increases much more slowly due to the first-order noise shaper. Still, it is important to keep in mind that the one-bit DAC imposes some design considerations. Figure 2 shows the THD + N of the converter versus “System Clock” frequency. This is the clock used to operate the one-bit DAC and noise shaper. Generally, the higher the oversampling the better. However, near full-scale, the converter is limited by other constraints and higher clock frequencies (past 96fs) tend to slightly worsen its performance. At low levels, performance improves almost linearly with increasing clock frequency. The one-bit DAC was designed to operate between 96fs (4X oversampling) and 384fs (16X oversampling). But, it can be operated at 48fs (2X oversampling) with slightly reduced performance. Recently, DACs employing a different architecture have been introduced. Most of these DACs utilize a one-bit DAC with “noise shaping” techniques and very high oversampling rate to achieve the digital-to-analog conversion. Basically, the trade-off is from very accurate but slow current sources to one rapidly sampled current source whose average output in the audio frequency range is equal to the current desired. Noise shaping insures that the “undesirable” frequencies associated with one-bit DAC output lie outside the audio range. These “Bitstream”, “MASH”, or one-bit DACs overcome the low level linearity problems of conventional DACs, since there can be no major carry error. However, this architecture exhibits problems of its own: signal-to-noise performance is usually worse than a similar conventional DAC, “dither noise” may be needed in order to get rid of unwanted tones, a separate high-speed clock may be required, the part may show sensitivity to clock jitter, and a high-order low-pass filter is necessary to filter the DAC output. The PCM67/69A is a cross between these two architectures. It includes both a conventional laser-trimmed, current-source DAC and an advanced one-bit DAC. The conventional DAC is a 10-bit DAC where each bit weight has been trimmed to 18bit linearity. The one-bit DAC has a weight equal to bit 10 and employs a first-order noise shaper to generate the “bitstream.” TOTAL HARMONIC DISTORTION + NOISE A key specification for audio DACs is usually total harmonic distortion plus noise (THD + N). For the PCM67/69A, THD + N is tested in production as shown in Figure 12. Digital data words are read into the PCM67/69A at eight times the standard compact disk audio sampling frequency of 44.1kHz (352.8kHz) so that a sine wave output of 991Hz is realized. The output of the DAC goes to an I-to-V converter, then to a programmable gain amplifier to provide gain at lower signal output test levels, and then through a 40kHz low pass filter before being fed into an analog type distortion analyzer. This approach does not eliminate all the problems associated with the two architectures but rather minimizes them as much as possible. The conventional DAC still exhibits some major carry error which would normally reduce low-level linearity. However, to reduce this error even further, the PCM67/69A utilizes an offset technique whereby bit n is subtracted from the digital input code whenever it is positive (see Figure 1 and Table I). When this is done, an offset current equal to the ® PCM67/69A 10 Use 400Hz High-Pass Filter and 30kHz Low-Pass Filter Meter Settings Distortion Analyzer Programmable Gain Amp 0dB to 60dB Low-Pass Filter 40kHz 3rd-Order GIC Type Parallel-to-Serial Conversion DUT (PCM67/69A) (Shiba Soku Model 725 or Equivalent) Binary Counter Digital Code (EPROM) I-to-V Converter OPA627 System Clock Bit Clock Word Clock Timing Logic Sampling Rate = 44.1kHz x 8 (352.8kHz) Output Frequency = 991Hz FIGURE 12. PCM67/69A THD+N Production Test. C10 1000pF R5 2kΩ +5V 11 10 12 9 13 8 R7 200Ω A2 +C 6 100µF 7 6 + 16 5 17 4 18 3 19 2 20 1 15 R4 680Ω C5 + PCM67 or PCM69A + 14 Digital In C8 10µF 1000pF R6 R3 680Ω C4 + C12 2200pF C9 10µF 10µF OUT R-ch 2.5V ± 1.2V 2kΩ R8 200Ω A1 R2 680Ω R1 680Ω VCC (+5V) + + C1 0.1µF + C3 100µF OUT L-ch 2.5V ± 1.2V C7 10µF + C11 2200pF A1, A2; NJM2100 or LM833 +C 2 100µF FIGURE 13. Single +5V Power Supply, with LPF, I/V Amp Application Circuit for Portable Digital Audio. ® 11 PCM67/69A PCM67/69A 12 10pF 10pF 1MΩ 16.9344MHz (192FS ) Interleaved Digital Input +5V DGND 4700pF 150Ω AGND 4 14 100pF 1 DA 17 3 28 L/R 15 5 Yamaha YM3623 2 BCO 12 + 6 0.1µF 4.7µF 6 7 + 4.7µF φA 8 28 1 17.1kΩ Digital Interface Format Receiver + 4.7µF +5V 17 A4 14 4 8 10 16 21 5 6 1.5kΩ 1.5kΩ 1.5kΩ 14 LDATA DOL 24 3.3µF 5 LIOUT 3 –15V 4 A3 8 1 4.7µF + 4.7µF 2200pF 510Ω +15V 2200pF 2 3 8 1µF LVCOM 2 16 +5V 9 Burr-Brown PCM67P/69AP (Note: 16-Pin DIP) 13 WDCK WCK 25 Burr-Brown DF1700P 7 2200pF 11 BTCK 12 SYSCK 3.3µF 4 15 18-Bit D/A Converter 10 RDATA 1 BCO 26 22 4.7µF 10µF DOR 23 8X Interpolation Digital Filter 3 +5V + ® 2 3 –15V 4 A2 8 1 4.7µF + 4.7µF 5kΩ 220pF A1 A1 to A4 = Burr-Brown OPA2604AP or NE5532 equivalent. 100kΩ 3.3µF +15V 10µF 5 6 VOUT Left 2.7kΩ NOTE: Only left channel shown. + FIGURE 14. HiFi D/A Converter Unit Application with Digital Audio Interface Format. IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. Customers are responsible for their applications using TI components. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 2000, Texas Instruments Incorporated