PIC18FXXK80 FAMILY Flash Microcontroller Programming Specification 1.0 DEVICE OVERVIEW 2.1 When programming with the ICSP, the PIC18FXXK80 family requires two programmable power supplies; one for VDD and one for MCLR/VPP/RE3. Both supplies should have a minimum resolution of 0.25V. Refer to Section 6.0 “AC/DC Characteristics Timing Requirements for Program/Verify Test Mode” for additional hardware parameters. This document includes the programming specifications for the following devices: • PIC18F25K80 • PIC18F26K80 • PIC18LF25K80 • PIC18LF26K80 • PIC18F45K80 • PIC18F46K80 • PIC18LF45K80 • PIC18LF46K80 • PIC18F65K80 • PIC18F66K80 • PIC18LF65K80 • PIC18LF66K80 2.0 Hardware Requirements 2.1.1 LOW-VOLTAGE ICSP™ PROGRAMMING In Low-Voltage ICSP mode, the PIC18FXXK80 family can be programmed using a VDD source in the operating range. The MCLR/VPP/RE3 pin does not have to be brought to a different voltage, but can instead, be left at the normal operating voltage. Refer to Section 6.0 “AC/DC Characteristics Timing Requirements for Program/Verify Test Mode” for additional hardware parameters. PROGRAMMING OVERVIEW The PIC18FXXK80 family of devices can be programmed using the In-Circuit Serial Programming™ (ICSP™) method. This programming specification applies to the PIC18FXXK80 family of devices in all package types. 2.2 Pin Diagrams The pin diagrams for the PIC18FXXK80 family are shown in Figure 2-1 and Figure 2-2. TABLE 2-1: PIN DESCRIPTIONS (DURING PROGRAMMING): PIC18FXXK80 FAMILY During Programming Pin Name Pin Name Pin Type MCLR/VPP/RE3 VPP P Programming Enable VDD(1) VSS(1) VDD P Power Supply VSS P Ground AVDD AVDD P Analog Power Supply AVSS AVSS P Analog Ground RB6 PGC I Serial Clock RB7 PGD I/O Serial Data VDDCORE P Regulated Power Supply for Microcontroller Core VCAP I Filter Capacitor for On-Chip Voltage Regulator VDDCORE/ VCAP Pin Description Legend: I = Input, O = Output, P = Power Note 1: All power supply (VDD) and ground (VSS) pins must be connected. 2011 Microchip Technology Inc. DS39972B-page 1 PIC18FXXK80 FAMILY FIGURE 2-1: PIC18FXXK80 FAMILY PIN DIAGRAMS 28-Pin QFN DS39972B-page 2 RB6/PGC RB5 RB4 23 22 RB7/PGD 14 RC4 RC5 RC6 RA6 RC3 RA7 5 6 7 RC2 VSS PIC18F2XK80 9 10 11 12 13 RA5 21 20 19 18 17 16 15 8 VDDCORE/VCAP 1 2 3 4 RC1 RA3 RC0 RA2 25 24 RA0 MCLR/VPP/RE3 28 27 26 RA1 The following devices are included in 28-pin QFN parts: • PIC18F25K80 • PIC18F26K80 • PIC18LF25K80 • PIC18LF26K80 RB3 RB2 RB1 RB0 VDD VSS RC7 2011 Microchip Technology Inc. PIC18FXXK80 FAMILY FIGURE 2-2: PIC18F8XKXX FAMILY PIN DIAGRAMS 28-PIN PDIP/SOIC/SSOP The following devices are included in 28-pin PDIP/SOIC/SSOP parts: • PIC18F25K80 • PIC18F26K80 • PIC18LF25K80 • PIC18LF26K80 MCLR/VPP/RE3 RA0 28 RB7/PGD 2 3 27 RB6/PGC RB4 RA2 4 26 25 RA3 5 6 24 RB3 23 RB2 22 RB1 RB0 9 10 21 20 19 RC0 11 18 RC7 RC1 17 16 RC6 RC2 12 13 RC3 14 15 RC4 RA1 VDDCORE/VCAP RA5 VSS RA7 RA6 2011 Microchip Technology Inc. 1 7 8 PIC18F2XK80 RB5 VDD VSS RC5 DS39972B-page 3 PIC18FXXK80 FAMILY FIGURE 2-3: PIC18F8XKXX FAMILY PIN DIAGRAMS 40-PIN PDIP The following devices are included in 40-pin PDIP parts: • PIC18F45K80 • PIC18F46K80 • PIC18LF45K80 • PIC18LF46K80 MCLR/VPP/RE3 1 40 RB7/PGD RA0 39 RB6/PGC RA1 2 3 RA2 4 38 37 RB4 RA3 5 6 36 RB3 35 RB2 7 8 34 33 RB1 32 VDD RE2 9 10 31 VSS VDD 11 30 RD7 VSS 12 13 29 RD6 VDDCORE/VCAP RA5 RE0 RE1 RA7 RA6 RB0 28 RD5 27 RD4 26 25 RC7 RC1 14 15 16 RC2 17 24 RC5 RC3 18 23 RC4 RD0 19 22 RD3 RD1 20 21 RD2 RC0 DS39972B-page 4 PIC18F4XK80 RB5 RC6 2011 Microchip Technology Inc. PIC18FXXK80 FAMILY FIGURE 2-4: PIC18F8XKXX FAMILY PIN DIAGRAMS 44-PIN TQFP/QFN 2011 Microchip Technology Inc. RD2 RD1 RD0 RC1 N/C 39 38 37 36 35 34 RC2 RC4 RC3 RC5 42 41 40 RD3 RC6 43 22 RA3 RA2 RA1 18 19 20 21 N/C RB3 RA0 RB2 MCLR/VPP/RE3 9 10 11 26 25 24 23 17 RB1 RA6 RA7 RB7/PGD 8 RC0 31 30 29 28 27 PIC18F4XK80 RB6/PGC RB0 VSS RB5 VDD 5 6 7 RD7 N/C 14 15 16 RD6 33 32 RB4 RD5 1 2 3 4 12 13 RD4 N/C RC7 44 The following devices are included in 44-pin TQFP/QFN parts: • PIC18F45K80 • PIC18F46K80 • PIC18LF45K80 • PIC18LF46K80 VSS VDD RE2 RE1 RE0 RA5 VDDCORE/VCAP DS39972B-page 5 PIC18FXXK80 FAMILY FIGURE 2-5: PIC18F8XKXX FAMILY PIN DIAGRAMS 64-PIN TQFP/QFN RC7 RD4 RD5 RD6 RD7 RG0 RG1 VSS AVDD VDD RG2 RG3 RB0 RB1 RC1 RC2 RC3 RF6 RF7 RD0 RD1 VSS VDD RD2 RD3 RE6 RC4 62 61 60 59 58 57 56 55 54 53 52 51 50 49 RC5 63 RE7 RC6 48 47 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 46 45 44 43 42 41 40 39 38 37 PIC18F6XK80 36 35 34 33 RC0 RA6 RA7 RF5 RF4 VSS AVSS VDD AVDD RE2 RE1 RE0 RF3 RF2 RA5 VDDCORE/VCAP DS39972B-page 6 RA3 RA2 RA1 RA0 MCLR/VPP/RE3 RE4 VSS VDD RE5 RB7/PGD RB6/PGC RB5 RF1 RB4 RG4 RF0 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 RB2 RB3 64 The following devices are included in 64-pin TQFP/QFN parts: • PIC18F65K80 • PIC18F66K80 • PIC18LF65K80 • PIC18LF66K80 2011 Microchip Technology Inc. PIC18FXXK80 FAMILY 2.3 On-Chip Voltage Regulator The PIC18FXXK80 device family is available with or without an internal core voltage regulator. On the devices with a voltage regulator (“PIC18F” in the part number), the regulator is always enabled. The regulator input is taken from the microcontroller VDD pins. The output of the regulator is supplied internally to the VDDCORE/VCAP pin. This pin simultaneously serves as both the regulator output and the microcontroller core power input pin. For these devices, a low-ESR (< 5Ω) capacitor is required on the VCAP/VDDCORE pin to stabilize the voltage regulator output voltage. The VCAP/ VDDCORE pin must not be connected to VDD and must use a capacitor that is typically 10 F connected to ground. On the devices that do not have a voltage regulator (“PIC18LF” in the part number), power to the CPU core must be externally supplied through the microcontroller VDD pins. VDDCORE/VCAP is internally connected to VDD. A 0.1 µF capacitor should be connected to the VDDCORE/ VCAP pin. Examples are shown in Figure 2-6. The specifications for core voltage and capacitance are listed in Section 6.0 “AC/DC Characteristics Timing Requirements for Program/Verify Test Mode”. 2011 Microchip Technology Inc. FIGURE 2-6: CONNECTIONS FOR THE ON-CHIP REGULATOR Regulator Enabled (PIC18FXXK80 Parts): 5V(1) PIC18FXXK80 VDD VDDCORE/VCAP CF VSS Regulator Disabled (PIC18LFXXK80 Parts): 3.3V(1) PIC18LFXXK80 VDD VDDCORE/VCAP(2) CF VSS Note 1: These are typical operating voltages. Refer to Section 6.0 “AC/DC Characteristics Timing Requirements for Program/Verify Test Mode”. 2: When the regulator is disabled, VDDCORE/ VCAP must be connected to a 0.1 µF capacitor. DS39972B-page 7 PIC18FXXK80 FAMILY 2.4 TABLE 2-2: Memory Maps For PIC18FX6K80 devices, the code memory space extends from 000000h to 00FFFFh (64 Kbytes) in four 16-Kbyte blocks. For PIC18FX5K80 devices, the code memory space extends from 000000h to 007FFFh (32 Kbytes) in four 8-Kbyte blocks. Addresses, 0000h through 07FFh or 0FFFh, however, define a “Boot Block” region that is treated separately from Block 0. All of these blocks define code protection boundaries within the code memory space. The size of the Boot Block in PIC18FXXK80 devices can be configured as 1 or 2K words (see Table 5-3). This is done through the BBSIZ bit in the Configuration register, CONFIG4L (see Table 5-1). It is important to note that increasing the size of the Boot Block decreases the size of Block 0. IMPLEMENTATION OF CODE MEMORY Device Code Memory Size (Bytes) PIC18F65K80 PIC18F45K80 PIC18F25K80 000000h-007FFFh (32K) PIC18LF65K80 PIC18LF45K80 PIC18LF25K80 PIC18F66K80 PIC18F46K80 PIC18F26K80 000000h-00FFFFh (64K) PIC18LF66K80 PIC18LF46K80 PIC18LF26K80 MEMORY MAP AND THE CODE MEMORY SPACE FOR PIC18FXXK80 DEVICES(1) FIGURE 2-7: 000000h Code Memory 01FFFFh Device/Memory Size PIC18FX6K80 PIC18FX5K80 BBSIZ = 1 BBSIZ = 0 BBSIZ = 1 BBSIZ = 0 Unimplemented Read as ‘0’ Boot Block(2) 2 KW Block 0 6 KW Block 1 8 KW 200000h Configuration and ID Space Boot Block(2) Block 0 7 KW Block 1 8 KW Boot Block(2) 2 KW Block 0 2 KW Boot Block(2) Block 0 3 KW Address 0000h 0800h 1000h 1FFFh Block 1 4 KW Block 1 4 KW 2000h 3FFFh Block 2 4 KW Block 2 4 KW 4000h 5FFFh Block 3 4 KW Block 3 4 KW 6000h 7FFFh Block 2 8 KW Block 2 8 KW 8000h BFFFh Block 3 8 KW Block 3 8 KW C000h FFFFh 3FFFFFh Note 1: 2: Sizes of memory areas are not to scale. Boot block size is determined by the BBSIZ bit (CONFIG4L<4>). DS39972B-page 8 2011 Microchip Technology Inc. PIC18FXXK80 FAMILY In addition to the code memory space, there are three blocks in the configuration and ID space that are accessible to the user through table reads and table writes. Their locations in the memory map are shown in Figure 2-8. Users may store Identification (ID) information in eight ID registers. These ID registers are mapped in addresses, 200000h through 200007h. The ID locations read out normally, even after code protection is applied. Locations, 300000h through 30000Dh, are reserved for the Configuration bits. These bits select various device options and are described in Section 5.0 “Configuration Word”. These Configuration bits read out normally, even after code protection. 2.4.1 MEMORY ADDRESS POINTER Memory in the address space, 0000000h to 3FFFFFh, is addressed via the Table Pointer register, which is comprised of three Pointer registers: • TBLPTRU, at RAM address 0FF8h • TBLPTRH, at RAM address 0FF7h • TBLPTRL, at RAM address 0FF6h TBLPTRU TBLPTRH TBLPTRL Addr<21:16> Addr<15:8> Addr<7:0> The 4-bit command, ‘0000’ (core instruction), is used to load the Table Pointer prior to using many read or write operations. Locations, 3FFFFEh and 3FFFFFh, are reserved for the Device ID bits. These bits may be used by the programmer to identify what device type is being programmed and are described in Section 5.0 “Configuration Word”. These Device ID bits read out normally, even after code protection. 2011 Microchip Technology Inc. DS39972B-page 9 PIC18FXXK80 FAMILY FIGURE 2-8: CONFIGURATION AND ID LOCATIONS FOR PIC18FXXK80 FAMILY DEVICES 000000h Code Memory 01FFFFh Unimplemented Read as ‘0’ 1FFFFFh Configuration and ID Space 2FFFFFh ID Location 1 200000h ID Location 2 200001h ID Location 3 200002h ID Location 4 200003h ID Location 5 200004h ID Location 6 200005h ID Location 7 200006h ID Location 8 200007h CONFIG1L 300000h CONFIG1H 300001h CONFIG2L 300002h CONFIG2H 300003h CONFIG3L 300004h CONFIG3H 300005h CONFIG4L 300006h CONFIG4H 300007h CONFIG5L 300008h CONFIG5H 300009h CONFIG6L 30000Ah CONFIG6H 30000Bh CONFIG7L 30000Ch CONFIG7H 30000Dh Device ID1 3FFFFEh Device ID2 3FFFFFh 3FFFFFh Note: Sizes of memory areas are not to scale. DS39972B-page 10 2011 Microchip Technology Inc. PIC18FXXK80 FAMILY 2.5 High-Level Overview of the Programming Process Figure 2-9 shows the high-level overview of the programming process. First, a Block Erase is performed for each block. Next, the code memory, ID locations and data EEPROM are programmed. These memories are then verified to ensure that programming was successful. If no errors are detected, the Configuration bits are then programmed and verified. FIGURE 2-9: HIGH-LEVEL PROGRAMMING FLOW Start Perform Sequential Block Erase Procedure Program Memory Program IDs Program Data EE 2.6 Entering and Exiting High-Voltage ICSP Program/Verify Mode As shown in Figure 2-11, entering High-Voltage ICSP Program/Verify mode requires two steps. First, voltage is applied to the MCLR pin. Second, a 32-bit key sequence is presented on PGD. The programming voltage applied to MCLR is VIHH. VIHH must be applied to MCLR during the transfer of the key sequence. After VIHH is applied to MCLR, an interval of at least P12 must elapse before presenting the key sequence on PGD. The key sequence is a specific 32-bit pattern,‘0100 1101 0100 0011 0100 1000 0101 0000’ (more easily remembered as 4D434850h in hexadecimal). The device will enter Program/Verify mode only if the sequence is valid. The Most Significant bit of the most significant nibble must be shifted in first. Once the key sequence is complete, Program/Verify mode is entered, and the program memory can be accessed and programmed in serial fashion. While in the Program/Verify mode, all unused I/Os are placed in the high-impedance state. Exiting Program/Verify mode is done by removing VIHH from MCLR, as shown in Figure 2-13. The only requirement for exit is that an interval, P16, should elapse between the last clock and the program signals on PGC and PGD before removing VIHH. Verify Program Verify IDs Verify Data Program Configuration Bits Verify Configuration Bits Done 2011 Microchip Technology Inc. DS39972B-page 11 PIC18FXXK80 FAMILY FIGURE 2-10: ENTERING LOW-VOLTAGE PROGRAM/VERIFY MODE P13 P1 VIH VIH MCLR VDD Program/Verify Entry Code = 4D434850h 0 b31 PGD 1 b30 0 b29 0 b28 1 ... b27 0 b3 0 b2 0 b1 0 b0 0 b1 0 b0 PGC P2B P2A P12 FIGURE 2-11: ENTERING HIGH-VOLTAGE PROGRAM/VERIFY MODE P13 P1 MCLR VIHH VDD Program/Verify Entry Code = 4D434850h 0 b31 PGD 1 b30 0 b29 0 b8 1 ... b27 0 b3 0 b2 PGC P12 DS39972B-page 12 P2B P2A 2011 Microchip Technology Inc. PIC18FXXK80 FAMILY FIGURE 2-12: EXITING LOW-VOLTAGE PROGRAM/VERIFY MODE P16 MCLR/VPP/RE3 P17 P1 D041 Exiting Program/Verify mode is done by grounding the MCLR again, as shown in Figure 2-12. The only requirement for exit is that an interval, P16, should elapse between the last clock, and the program signals on PGC and PGD before grounding MCLR. VDD PGD PGC 2.8 PGD = Input FIGURE 2-13: EXITING HIGH-VOLTAGE PROGRAM/VERIFY MODE P16 MCLR/VPP/RE3 P17 P1 VDD PGD PGC PGD = Input Entering and Exiting Low-Voltage ICSP Program/Verify Mode As shown in Figure 2-10, entering Low-Voltage ICSP Program/Verify mode requires three steps: 1. 2. 3. Serial Program/Verify Operation The PGC pin is used as a clock input pin, and the PGD pin is used for entering command bits and data input/ output during serial operation. Commands and data are transmitted on the rising edge of PGC, latched on the falling edge of PGC, and are Least Significant bit (LSb) first. 2.8.1 4-BIT COMMANDS All instructions are 20 bits, consisting of a leading 4-bit command, followed by a 16-bit operand, which depends on the type of command being executed. To input a command, PGC is cycled four times. The commands needed for programming and verification are shown in Table 2-3. Commands and data are entered LSb first. D110 2.7 Once the key sequence is complete, VIH, or usually VDD, must be applied to MCLR and held at that level for as long as Program/Verify mode is to be maintained. There is no minimum time requirement before presenting data on PGD. On successful entry, the program memory can be accessed and programmed in serial fashion. While in the Program/Verify mode, all unused I/Os are placed in the high-impedance state. Depending on the 4-bit command, the 16-bit operand represents 16 bits of input data, or 8 bits of input data and 8 bits of output data. Throughout this specification, commands and data are presented as illustrated in Table 2-4. The 4-bit command and data are shown Most Significant bit (MSb) first. The command operand, or “Data Payload”, is shown as <LSB><MSB>. Figure 2-14 demonstrates how to serially present a 20-bit command/operand to the device. The MCLR pin is grounded. A 32-bit key sequence is presented on PGD. The MCLR pin is brought to VDD The MCLR pin must be grounded during the transfer of the key sequence. After MCLR is grounded, an interval of at least P12 must elapse before presenting the key sequence on PGD. The key sequence is a specific 32-bit pattern,‘0100 1101 0100 0011 0100 1000 0101 0000’ (more easily remembered as 4D434850h in hexadecimal). The device will enter Program/Verify mode only if the sequence is valid. The Most Significant bit of the most significant nibble must be shifted in first. 2011 Microchip Technology Inc. DS39972B-page 13 PIC18FXXK80 FAMILY 2.8.2 TABLE 2-4: CORE INSTRUCTION The core instruction passes a 16-bit instruction to the CPU core for execution. This is needed to set up registers, as appropriate, for use with other commands. TABLE 2-3: COMMANDS FOR PROGRAMMING Core Instruction (shift in 16-bit instruction) 0000 Shift out TABLAT Register 0010 Table Read 1000 Table Read, Post-Increment 1001 Table Read, Post-Decrement 1010 Table Read, Pre-Increment 1011 Table Write 1100 Table Write, Post-Increment by 2 1101 Table Write, Start Programming, Post-Increment by 2 1110 Table Write, Start Programming 1111 Data Payload 1101 3C 40 Core Instruction Table Write, post-increment by 2 TABLE WRITE, POST-INCREMENT TIMING (‘1101’) P2 1 4-Bit Command 4-Bit Command Description FIGURE 2-14: SAMPLE COMMAND SEQUENCE 2 3 P2A P2B 4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 2 1 3 4 PGC P5A P5 P4 LSB P3 PGD 1 LSb 0 1 1 MSb 4-Bit Command 0 LSb 0 0 0 0 0 MSB 0 1 0 0 0 1 4 C 16-Bit Data Payload 1 1 1 0 3 0 n n n n MSb Fetch Next 4-Bit Command PGD = Input DS39972B-page 14 2011 Microchip Technology Inc. PIC18FXXK80 FAMILY 3.0 DEVICE PROGRAMMING Programming includes the ability to erase or write the various memory regions within the device. In all cases except ICSP Block Erase, the EECON1 register must be configured in order to operate on a particular memory region. When using the EECON1 register to act on code memory, the EEPGD bit must be set (EECON1<7> = 1) and the CFGS bit must be cleared (EECON1<6> = 0). REGISTER 3-1: R/W-x EECON1 REGISTER R/W-x EEPGD The WREN bit must be set (EECON1<2> = 1) to enable writes of any sort (e.g., erases) and this must be done prior to initiating a write sequence. The FREE bit must be set (EECON1<4> = 1) in order to erase the program space being pointed to by the Table Pointer. The erase or write sequence is initiated by setting the WR bit (EECON1<1> = 1). It is strongly recommended that the WREN bit only be set immediately prior to a program or erase. CFGS U-0 — R/W-0 FREE R/W-x (1) WRERR R/W-0 R/S-0 R/S-0 WREN WR RD bit 7 bit 0 Legend: R = Readable bit W = Writable bit S = Bit can be set by software, but not cleared U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘0’ = Bit is cleared ‘1’ = Bit is set x = Bit is unknown bit 7 EEPGD: Flash Program or Data EEPROM Memory Select bit 1 = Access Flash program memory 0 = Access data EEPROM memory bit 6 CFGS: Flash Program/Data EEPROM or Configuration Select bit 1 = Access Configuration registers 0 = Access Flash program or data EEPROM memory bit 5 Unimplemented: Read as ‘0’ bit 4 FREE: Flash Row Erase Enable bit 1 = Erase the program memory row addressed by TBLPTR on the next WR command (cleared by completion of erase operation) 0 = Perform write-only bit 3 WRERR: Flash Program/Data EEPROM Error Flag bit(1) 1 = A write operation is prematurely terminated (any Reset during self-timed programming in normal operation or an improper write attempt) 0 = The write operation completed bit 2 WREN: Flash Program/Data EEPROM Write Enable bit 1 = Allows write cycles to Flash program/data EEPROM 0 = Inhibits write cycles to Flash program/data EEPROM bit 1 WR: Write Control bit 1 = Initiates a data EEPROM erase/write cycle or a program memory erase/write cycle (The operation is self-timed and the bit is cleared by hardware once the write is complete. The WR bit can only be set (not cleared) in software.) 0 = Write cycle to the EEPROM is complete bit 0 RD: Read Control bit 1 = Initiates an EEPROM read (Read takes one cycle. RD is cleared in hardware. The RD bit can only be set (not cleared) in software. The RD bit cannot be set when EEPGD = 1 or CFGS = 1.) 0 = Does not initiate an EEPROM read Note 1: When a WRERR occurs, the EEPGD and CFGS bits are not cleared. This allows tracing of the error condition. 2011 Microchip Technology Inc. DS39972B-page 15 PIC18FXXK80 FAMILY 3.1 3.1.1 TABLE 3-2: ICSP Erase ICSP BLOCK ERASE Erasing code or data EEPROM is accomplished by configuring three Block Erase Control registers, located at 3C0004h through 3C0006h. Code memory can only be erased, portions at a time. In order to erase the entire device, every block must be erased sequentially. Block Erase operations will also clear any code-protect settings associated with the memory block being erased. Erase options are detailed in Table 3-1. Data EEPROM is erased at the same time as all Block Erase commands. In order to erase data EEPROM by itself, the first code sequence in Table 3-1 must be used. If the entire device is being erased, this code is not necessary. TABLE 3-1: BLOCK ERASE OPERATIONS Description Data (3C0006h:3C0004h) Erase Data EEPROM Erase Boot Block Erase Config Bits Erase Code EEPROM Block 0 Erase Code EEPROM Block 1 Erase Code EEPROM Block 2 Erase Code EEPROM Block 3 800004h 800005h 800002h 800104h 800204h 800404h 800804h The actual Block Erase function is a self-timed operation. Once the erase has started (falling edge of the 4th PGC after the NOP command), serial execution will cease until the erase completes (Parameter P11). During this time, PGC may continue to toggle, but PGD must be held low. The code sequence to erase the entire device is shown in Table 3-2 through Table 3-7 and the flowchart is shown in Figure 3-1. The code sequence to just erase data EEPROM is shown in Table 3-8. Note: A Block Erase is the only way to reprogram code-protect bits from an ON state to an OFF state. 4-Bit Command Data Payload 0000 0000 0000 0000 0000 0000 1100 0000 0000 1100 0000 0000 1100 0E 6E 0E 6E 0E 6E 04 0E 6E 01 0E 6E 80 0000 0000 00 00 00 00 TABLE 3-3: 4-Bit Command 0000 0000 0000 0000 0000 0000 1100 0000 0000 1100 0000 0000 1100 0000 0000 3C F8 00 F7 04 F6 04 05 F6 01 06 F6 80 Core Instruction MOVLW 3Ch MOVWF TBLPTRU MOVLW 00h MOVWF TBLPTRH MOVLW 04h MOVWF TBLPTRL Write 04h to 3C0004h MOVLW 05h MOVWF TBLPTRL Write 01h to 3C0005h MOVLW 06h MOVWF TBLPTRL Write 80h to 3C0006h to erase block 0 NOP Hold PGD low until erase completes ERASE BLOCK 1 Data Payload 0E 6E 0E 6E 0E 6E 04 0E 6E 02 0E 6E 80 3C F8 00 F7 04 F6 04 05 F6 02 06 F6 80 00 00 00 00 TABLE 3-4: 4-Bit Command DS39972B-page 16 ERASE BLOCK 0 Core Instruction MOVLW 3Ch MOVWF TBLPTRU MOVLW 00h MOVWF TBLPTRH MOVLW 04h MOVWF TBLPTRL Write 04h to 3C0004h MOVLW 05h MOVWF TBLPTRL Write 02h to 3C0005h MOVLW 06h MOVWF TBLPTRL Write 80h to 3c0006h to erase block 1 NOP Hold PGD low until erase completes ERASE BLOCK 2 Data Payload 0000 0000 0000 0000 0000 0000 1100 0000 0000 1100 0000 0000 1100 0E 6E 0E 6E 0E 6E 04 0E 6E 04 0E 6E 80 0000 0000 00 00 00 00 3C F8 00 F7 04 F6 04 05 F6 04 06 F6 80 Core Instruction MOVLW 3Ch MOVWF TBLPTRU MOVLW 00h MOVWF TBLPTRH MOVLW 04h MOVWF TBLPTRL Write 04h to 3C0004h MOVLW 05h MOVWF TBLPTRL Write 04h to 3C0005h MOVLW 06h MOVWF TBLPTRL Write 80h to 3C0006h to erase block 2 NOP Hold PGD low until erase completes 2011 Microchip Technology Inc. PIC18FXXK80 FAMILY TABLE 3-5: 4-Bit Command ERASE BLOCK 3 Data Payload 0000 0000 0000 0000 0000 0000 1100 0000 0000 1100 0000 0000 1100 0E 6E 0E 6E 0E 6E 04 0E 6E 08 0E 6E 80 0000 0000 00 00 00 00 TABLE 3-6: 4-Bit Command 3C F8 00 F7 04 F6 04 05 F6 08 06 F6 80 Core Instruction MOVLW 3Ch MOVWF TBLPTRU MOVLW 00h MOVWF TBLPTRH MOVLW 04h MOVWF TBLPTRL Write 04h to 3C0004h MOVLW 05h MOVWF TBLPTRL Write 08h to 3C0005h MOVLW 06h MOVWF TBLPTRL Write 80h to 3C0006h to erase block 3 NOP Hold PGD low until Erase completes TABLE 3-7: 4-Bit Command ERASE CONFIGURATION FUSES Data Payload 0000 0000 0000 0000 0000 0000 1100 0000 0000 1100 0000 0000 1100 0E 6E 0E 6E 0E 6E 02 0E 6E 00 0E 6E 80 0000 0000 00 00 00 00 3C F8 00 F7 04 F6 02 05 F6 00 06 F6 80 Core Instruction MOVLW 3Ch MOVWF TBLPTRU MOVLW 00h MOVWF TBLPTRH MOVLW 04h MOVWF TBLPTRL Write 02h to 3C0004h MOVLW 05h MOVWF TBLPTRL Write 00h to 3C0005h MOVLW 06h MOVWF TBLPTRL Write 80h to 3C0006h to erase configuration fuses NOP Hold PGD low until Erase completes ERASE BOOT BLOCK TABLE 3-8: Data Payload 0000 0000 0000 0000 0000 0000 1100 0000 0000 1100 0000 0000 1100 0E 6E 0E 6E 0E 6E 05 0E 6E 00 0E 6E 80 0000 0000 00 00 00 00 3C F8 00 F7 04 F6 05 05 F6 00 06 F6 80 Core Instruction MOVLW 3Ch MOVWF TBLPTRU MOVLW 00h MOVWF TBLPTRH MOVLW 04h MOVWF TBLPTRL Write 05h to 3C0004h MOVLW 05h MOVWF TBLPTRL Write 00h to 3C0005h MOVLW 06h MOVWF TBLPTRL Write 80h to 3C0006h to erase boot block NOP Hold PGD low until Erase completes 2011 Microchip Technology Inc. 4-Bit Command ERASE DATA EEPROM Data Payload 0000 0000 0000 0000 0000 0000 1100 0000 0000 1100 0000 0000 1100 0E 6E 0E 6E 0E 6E 04 0E 6E 00 0E 6E 80 0000 0000 00 00 00 00 3C F8 00 F7 04 F6 04 05 F6 00 06 F6 80 Core Instruction MOVLW 3Ch MOVWF TBLPTRU MOVLW 00h MOVWF TBLPTRH MOVLW 04h MOVWF TBLPTRL Write 04h to 3C0004h MOVLW 05h MOVWF TBLPTRL Write 00h to 3C0005h MOVLW 06h MOVWF TBLPTRL Write 80h to 3C0006h to erase Data EEPROM NOP Hold PGD low until Erase completes DS39972B-page 17 PIC18FXXK80 FAMILY FIGURE 3-1: BLOCK ERASE FLOW Start Write 04h to 3C0004h Write 01h to 3C0005h Write 80h to 3C0006h to Erase Block 0 Delay P11 + P10 Time Write 04h to 3C0004h Write 02h to 3C0005h Write 80h to 3C0006h to Erase Block 1 Delay P11 + P10 Time Write 05h to 3C0004h Write 00h to 3C0005h Write 80h to 3C0006h to Erase Boot Block Delay P11 + P10 Time Write 02h to 3C0004h Write 00h to 3C0005h Write 80h to 3C0006h to Erase Config. Fuses Delay P11 + P10 Time Done Write 04h to 3C0004h Write 04h to 3C0005h Write 80h to 3C0006h to Erase Block 2 Delay P11 + P10 Time Write 04h to 3C0004h Write 08h to 3C0005h Write 80h to 3C0006h to Erase Block 3 Delay P11 + P10 Time DS39972B-page 18 2011 Microchip Technology Inc. PIC18FXXK80 FAMILY FIGURE 3-2: BLOCK ERASE TIMING P10 1 2 3 4 1 2 15 16 1 2 3 4 1 2 15 16 1 2 3 4 1 2 n n PGC PGD 0 0 1 1 4-Bit Command 1 1 0 0 16-Bit Data Payload P5A P5 P5A P5 0 0 0 0 4-Bit Command 0 0 0 0 16-Bit Data Payload P11 0 0 0 0 4-Bit Command Erase Time 16-Bit Data Payload PGD = Input 3.1.2 ICSP ROW ERASE It is possible to erase one row (64 bytes of data) provided the block is not code or write-protected. Rows are located at static boundaries beginning at program memory address, 000000h, extending to the internal program memory limit (see Section 2.4 “Memory Maps”). The Row Erase duration is externally timed and is controlled by PGC. After the WR bit in EECON1 is set, a NOP is issued, where the 4th PGC is held high for the duration of the programming time, P9. The code sequence to Row Erase a PIC18FXXK80 family device is shown in Table 3-9. The flowchart shown in Figure 3-3 depicts the logic necessary to completely erase a PIC18FXXK80 family device. The timing diagram that details the Start Programming command and Parameters P9 and P10 is shown in Figure 3-4. Note: The TBLPTR register can point to any byte within the row intended for erase. After PGC is brought low, the programming sequence is terminated. PGC must be held low for the time specified by Parameter P10 to allow high-voltage discharge of the memory array. 2011 Microchip Technology Inc. DS39972B-page 19 PIC18FXXK80 FAMILY TABLE 3-9: SINGLE ROW ERASE CODE MEMORY CODE SEQUENCE 4-Bit Command Data Payload Core Instruction Step 1: Direct access to code memory and enable writes. 0000 0000 0000 8E 7F 9C 7F 84 7F BSF BCF BSF EECON1, EEPGD EECON1, CFGS EECON1, WREN Step 2: Point to first row in code memory. 0000 0000 0000 6A F8 6A F7 6A F6 CLRF CLRF CLRF TBLPTRU TBLPTRH TBLPTRL Step 3: Enable erase and erase single row. 0000 0000 0000 88 7F 82 7F 00 00 BSF EECON1, FREE BSF EECON1, WR NOP – hold PGC high for time P9 and low for time P10. Step 4: Repeat Step 3 with Address Pointer incremented by 64 until all rows are erased. FIGURE 3-3: SINGLE ROW ERASE CODE MEMORY FLOW Start Addr = 0 Configure Device for Row Erases Start Erase Sequence and Hold PGC High for Time P9 Addr = Addr + 64 Hold PGC Low for Time P10 No All rows done? Yes Done DS39972B-page 20 2011 Microchip Technology Inc. PIC18FXXK80 FAMILY 3.2 Code Memory Programming The code sequence to program a PIC18FXXK80 family device is shown in Table 3-11. The flowchart, shown in Figure 3-6, depicts the logic necessary to completely write a PIC18FXXK80 family device. The timing diagram that details the Start Programming command, and Parameters P9 and P10 is shown in Figure 3-4. Programming code memory is accomplished by first loading data into the write buffer and then initiating a programming sequence. The write and erase buffer sizes, shown in Table 3-10, can be mapped to any location of the same size beginning at 000000h. The actual memory write sequence takes the contents of this buffer and programs the proper amount of code memory that contains the Table Pointer. Note: The programming duration is externally timed and is controlled by PGC. After a Start Programming command is issued (4-bit command, ‘1111’), a NOP is issued, where the 4th PGC is held high for the duration of the programming time, P9. TABLE 3-10: After PGC is brought low, the programming sequence is terminated. PGC must be held low for the time specified by Parameter P10 to allow high-voltage discharge of the memory array. FIGURE 3-4: The TBLPTR register must point to the same region when initiating the programming sequence as it did when the write buffers were loaded. WRITE AND ERASE BUFFER SIZES All Devices Write Buffer Size in Bytes Erase Buffer Size in Bytes PIC18FXXK80 64 64 TABLE WRITE AND START PROGRAMMING INSTRUCTION TIMING (‘1111’) P10 1 2 3 4 1 2 3 4 5 6 15 16 1 2 3 4 2 3 0 0 0 P9 P5A P5 PGD 1 (1) PGC 1 1 1 1 n 4-Bit Command n n n n n n n 16-Bit Data Payload 0 0 0 0 4-bit Command Programming Time 16-Bit Data Payload PGD = Input Note 1: Use P9A for User ID and Configuration Word programming. 2011 Microchip Technology Inc. DS39972B-page 21 PIC18FXXK80 FAMILY FIGURE 3-5: ERASE AND WRITE BOUNDARIES TBLPTR<21:16> = 1 64-byte Write Buffer Panel 2 TBLPTR<5:0> = 63 . . . . . TBLPTR<5:0> = 0 Erase Region 64 Bytes Offset = TBLPTR<15:6> TBLPTR<21:16> = 0 64-byte Write Buffer Panel 1 TBLPTR<5:0> = 63 . . . . . TBLPTR<5:0> = 0 Erase Region 64 Bytes Offset = TBLPTR<15:6> Note: TBLPTR = TBLPTRU:TBLPTRH:TBLPTRL. DS39972B-page 22 2011 Microchip Technology Inc. PIC18FXXK80 FAMILY 3.2.1 PROGRAMMING A maximum of 64 bytes can be programmed into the block referenced by TBLPTR<21:6>. The panel that will be written will automatically be enabled based on the value of the Table Pointer. TABLE 3-11: WRITE CODE MEMORY CODE SEQUENCE FOR PROGRAMMING 4-Bit Command Data Payload Core Instruction Step 1: Direct access to code memory and enable writes. 0000 0000 0000 8E 7F 9C 7F 84 7F BSF BCF BSF EECON1, EEPGD EECON1, CFGS EECON1, WREN MOVLW MOVWF MOVLW MOVWF MOVLW MOVWF <Addr[21:16]> TBLPTRU <Addr[15:8]> TBLPTRH <Addr[7:0]> TBLPTRL Step 2: Point to row to be written. 0000 0000 0000 0000 0000 0000 0E 6E 0E 6E 0E 6E <Addr[21:16]> F8 <Addr[15:8]> F7 <Addr[7:0]> F6 Step 3: Load write buffer for panel. Repeat for all but the last two bytes. Any unused locations should be filled with FFFFh. 1101 . . <MSB><LSB> . . Write 2 bytes and post-increment address by 2. . Repeat 31 times. Step 4: Load write buffer for last two bytes. . 1111 0000 . <MSB><LSB> 00 00 . Write 2 bytes and start programming NOP - hold SCLK high for time P9, low for time P10 To continue writing data, repeat Steps 3 and 4, where the Address Pointer is incremented by 64 at each iteration of the loop. 2011 Microchip Technology Inc. DS39972B-page 23 PIC18FXXK80 FAMILY FIGURE 3-6: PROGRAM CODE MEMORY FLOW Start LoopCount = 0 Configure Device for Writes Load 2 Bytes to Write Buffer at <Addr> LoopCount = LoopCount + 1 No All bytes written? Yes Start Write Sequence and Hold PGC High Until Done and Wait P9 No All locations done? Yes Done DS39972B-page 24 2011 Microchip Technology Inc. PIC18FXXK80 FAMILY 3.2.2 MODIFYING CODE MEMORY The previous programming example assumed that the device had been erased entirely prior to programming (see Section 3.1.1 “ICSP Block Erase”). It may be the case, however, that the user wishes to modify only a section of an already programmed device. The appropriate number of bytes required for the erase buffer must be read out of code memory (as described in Section 4.2 “Verify Code Memory and ID Locations”) and buffered. Modifications can be made on this buffer. Then, the block of code memory that was read out must be erased and rewritten with the modified data (see Section 3.2.1 “Programming”). The WREN bit must be set if the WR bit in EECON1 is used to initiate a write sequence. TABLE 3-12: MODIFYING CODE MEMORY 4-Bit Command Data Payload Core Instruction Step 1: Direct access to code memory. Step 2: Read and modify code memory (see Section 4.1 “Read Code Memory, ID Locations and Configuration Bits”). 0000 0000 8E 7F 9C 7F BSF BCF EECON1, EEPGD EECON1, CFGS Step 3: Set the Table Pointer for the block to be erased. 0000 0000 0000 0000 0000 0000 0E 6E 0E 6E 0E 6E <Addr[21:16]> F8 <Addr[8:15]> F7 <Addr[7:0]> F6 MOVLW MOVWF MOVLW MOVWF MOVLW MOVWF <Addr[21:16]> TBLPTRU <Addr[8:15]> TBLPTRH <Addr[7:0]> TBLPTRL Step 4: Enable memory writes and set up an erase. 0000 0000 84 7F 88 7F BSF BSF EECON1, WREN EECON1, FREE Step 5: Initiate erase. 0000 0000 82 7F 00 00 BSF EECON1, WR NOP - hold PGC high for time P9 and low for time P10. Step 6: Direct access to configuration memory. 0000 0000 0000 8E 7F 8C 7F 84 7F BSF BSF BSF EECON1, EEPGD EECON1, CFGS EECON1, WREN Step 7: Direct access to code memory and enable writes. 0000 0000 8E 7F 9C 7F BSF BCF EECON1, EEPGD EECON1, CFGS Step 8: Load write buffer. The correct bytes will be selected based on the Table Pointer. 0000 0000 0000 0000 0000 0000 1101 . . . 1111 0000 0E <Addr[21:16]> 6E F8 0E <Addr[8:15]> 6E F7 0E <Addr[7:0]> 6E F6 <MSB><LSB> . . . <MSB><LSB> 00 00 MOVLW <Addr[21:16]> MOVWF TBLPTRU MOVLW <Addr[8:15]> MOVWF TBLPTRH MOVLW <Addr[7:0]> MOVWF TBLPTRL Write 2 bytes and post-increment address by 2. Repeat 31 times Write 2 bytes and start programming. NOP - hold PGC high for time P9 and low for time P10. To continue modifying data, repeat Steps 2 through 8, where the Address Pointer is incremented by 64 bytes at each iteration of the loop. Step 9: Disable writes. 0000 94 7F 2011 Microchip Technology Inc. BCF EECON1, WREN DS39972B-page 25 PIC18FXXK80 FAMILY 3.3 FIGURE 3-7: Data EEPROM Programming PROGRAM DATA FLOW Data EEPROM is accessed, one byte at a time, via an Address Pointer (register pair, EEADRH:EEADR) and a Data Latch (EEDATA). Data EEPROM is written by loading EEADRH:EEADR with the desired memory location, EEDATA with the data to be written and initiating a memory write by appropriately configuring the EECON1 register (Register 3-1). A byte write automatically erases the location and writes the new data (erase-before-write). Start Set Address Set Data Enable Write When using the EECON1 register to perform a data EEPROM write, both the EEPGD and CFGS bits must be cleared (EECON1<7:6> = 00). The WREN bit must be set (EECON1<2> = 1) to enable writes of any sort and this must be done prior to initiating a write sequence. The write sequence is initiated by setting the WR bit (EECON1<1> = 1). Start Write Sequence The write begins on the falling edge of the 4th PGC after the WR bit is set. It ends when the WR bit is cleared by hardware. Yes No Done? After the programming sequence terminates, PGC must still be held low for the time specified by Parameter P10 to allow high-voltage discharge of the memory array. FIGURE 3-8: No WR bit clear? Yes Done DATA EEPROM WRITE TIMING P10 1 2 3 4 1 2 1 15 16 2 PGC P5A P5 PGD P11A n 0 0 0 0 4-Bit Command BSF EECON1, WR n 16-Bit Data Payload Poll WR Bit, Repeat until Clear (see below) PGD = Input 1 2 3 4 1 2 15 16 1 2 3 4 1 2 15 16 PGC P5 P5A P5 P5A Poll WR bit PGD 0 0 0 0 0 0 0 0 4-Bit Command MOVF EECON1, W, 0 PGD = Input DS39972B-page 26 4-Bit Command MOVWF TABLAT Shift Out Data (see Figure 4-4) PGD = Output 2011 Microchip Technology Inc. PIC18FXXK80 FAMILY TABLE 3-13: PROGRAMMING DATA MEMORY 4-Bit Command Data Payload Core Instruction Step 1: Direct access to data EEPROM. 0000 0000 9E 7F 9C 7F BCF BCF EECON1, EEPGD EECON1, CFGS Step 2: Set the data EEPROM Address Pointer. 0000 0000 0000 0000 0E 6E OE 6E <Addr> 74 <AddrH> 75 MOVLW MOVWF MOVLW MOVWF <Addr> EEADR <AddrH> EEADRH Step 3: Load the data to be written. 0000 0000 0E <Data> 6E 73 MOVLW <Data> MOVWF EEDATA Step 4: Enable memory writes. 0000 84 7F BSF EECON1, WREN BSF EECON1, WR Step 5: Initiate write. 0000 82 7F Step 6: Poll WR bit, repeat until the bit is clear. 0000 0000 0000 0010 50 7F 6E F5 00 00 <MSB><LSB> MOVF EECON1, W, 0 MOVWF TABLAT NOP Shift out data(1) Step 7: Hold PGC low for time, P10. Step 8: Disable writes. 0000 94 7F BCF EECON1, WREN Repeat Steps 2 through 8 to write more data. Note 1: See Figure 4-4 for details on shift out data timing. 2011 Microchip Technology Inc. DS39972B-page 27 PIC18FXXK80 FAMILY 3.4 ID Location Programming The ID locations are programmed much like the code memory. The ID registers are mapped in addresses, 200000h through 200007h. These locations read out normally even after code protection. Note: Table 3-14 demonstrates the code sequence required to write the ID locations. In order to modify the ID locations, refer to the methodology described in Section 3.2.2 “Modifying Code Memory”. As with code memory, the ID locations must be erased before being modified. The user only needs to fill the first 8 bytes of the write buffer in order to write the ID locations. TABLE 3-14: WRITE ID SEQUENCE 4-Bit Command Data Payload Core Instruction Step 1: Direct access to code memory and enable writes. 0000 0000 8E 7F 9C 7F BSF BCF EECON1, EEPGD EECON1, CFGS Step 2: Load write buffer with 8 bytes and write. 0000 0000 0000 0000 0000 0000 1101 1101 1101 1111 0000 0E 20 6E F8 0E 00 6E F7 0E 00 6E F6 <MSB><LSB> <MSB><LSB> <MSB><LSB> <MSB><LSB> 00 00 DS39972B-page 28 MOVLW MOVWF MOVLW MOVWF MOVLW MOVWF Write Write Write Write NOP - 20h TBLPTRU 00h TBLPTRH 00h TBLPTRL 2 bytes and post-increment address by 2 bytes and post-increment address by 2 bytes and post-increment address by 2 bytes and start programming. hold PGC high for time P9 and low for 2. 2. 2. time P10. 2011 Microchip Technology Inc. PIC18FXXK80 FAMILY 3.5 Boot Block Programming 3.6 The code sequence detailed in Table 3-11 should be used, except that the address used in “Step 2” will be in the range of 000000h to 0007FFh, or 000000h to 000FFFh, as defined by the BBSIZ bit in the CONFIG4L register (see Table 5-1). Configuration Bits Programming Unlike code memory, the Configuration bits are programmed a byte at a time. The Table Write, Begin Programming 4-bit command (‘1111’) is used, but only 8 bits of the following 16-bit payload will be written. The LSB of the payload will be written to even addresses and the MSB will be written to odd addresses. The code sequence to program two consecutive configuration locations is shown in Table 3-15. Note: TABLE 3-15: 4-Bit Command The address must be explicitly written for each byte programmed. The addresses can not be incremented in this mode. SET ADDRESS POINTER TO CONFIGURATION LOCATION Data Payload Core Instruction Step 1: Enable writes and direct access to configuration memory. 0000 0000 8E 7F 8C 7F BSF BSF EECON1, EEPGD EECON1, CFGS Step 2: Set Table Pointer for configuration byte to be written; write even/odd addresses.(1) 0000 0000 0000 0000 0000 0000 1111 0000 0000 0000 1111 0000 Note 1: 0E 30 6E F8 0E 00 6E F7 0E 00 6E F6 <MSB ignored><LSB> 00 00 0E 01 6E F6 <MSB><LSB ignored> 00 00 MOVLW 30h MOVWF TBLPTRU MOVLW 00h MOVWF TBLPTRH MOVLW 00h MOVWF TBLPTRL Load 2 bytes and start programming. NOP - hold PGC high for time P9 and low for time P10. MOVLW 01h MOVWF TBLPTRL Load 2 bytes and start programming. NOP - hold PGC high for time P9A and low for time P10. Enabling the write protection of the Configuration bits (WRTC = 0 in CONFIG6H) will prevent further writing of the Configuration bits. Always write all of the Configuration bits before enabling the write protection for the Configuration bits. FIGURE 3-9: CONFIGURATION PROGRAMMING FLOW Start Start Load Even Configuration Address Load Odd Configuration Address Program LSB Program MSB Delay P9A and P10 Time for Write Delay P9A and P10 Time for Write Done Done 2011 Microchip Technology Inc. DS39972B-page 29 PIC18FXXK80 FAMILY 4.0 READING THE DEVICE 4.1 Read Code Memory, ID Locations and Configuration Bits The 4-bit command is shifted in, LSb first. The read is executed during the next 8 clocks, then shifted out on PGD during the last 8 clocks, LSb to MSb. A delay of P6 must be introduced after the falling edge of the 8th PGC of the operand to allow PGD to transition from an input to an output. During this time, PGC must be held low (see Figure 4-1). This operation also increments the Table Pointer by one, pointing to the next byte in code memory for the next read. Code memory is accessed, one byte at a time, via the 4-bit command, ‘1001’ (table read, post-increment). The contents of memory pointed to by the Table Pointer (TBLPTRU:TBLPTRH:TBLPTRL) are serially output on PGD. TABLE 4-1: This technique will work to read any memory in the 000000h to 3FFFFFh address space, so it also applies to reading the ID and Configuration registers. READ CODE MEMORY SEQUENCE 4-Bit Command Data Payload Core Instruction Step 1: Set Table Pointer. 0000 0000 0000 0000 0000 0000 0E 6E 0E 6E 0E 6E <Addr[21:16]> F8 <Addr[15:8]> F7 <Addr[7:0]> F6 MOVLW MOVWF MOVLW MOVWF MOVLW MOVWF Addr[21:16] TBLPTRU <Addr[15:8]> TBLPTRH <Addr[7:0]> TBLPTRL Step 2: Read memory and then shift out on PGD, LSb to MSb. 1001 00 00 FIGURE 4-1: 1 TBLRD *+ TABLE READ, POST-INCREMENT INSTRUCTION TIMING (‘1001’) 2 3 4 1 2 3 4 5 6 7 9 8 1 10 11 12 13 14 15 16 2 3 4 PGC P5 P5A P6 P14 PGD 1 0 0 LSb 1 1 2 3 4 5 Shift Data Out PGD = Input DS39972B-page 30 PGD = Output 6 MSb n n n n Fetch Next 4-Bit Command PGD = Input 2011 Microchip Technology Inc. PIC18FXXK80 FAMILY 4.2 Verify Code Memory and ID Locations The verify step involves reading back the code memory space and comparing it against the copy held in the programmer’s buffer. Memory reads occur a single byte at a time, so two bytes must be read to compare against the word in the programmer’s buffer. Refer to Section 4.1 “Read Code Memory, ID Locations and Configuration Bits” for implementation details of reading code memory. FIGURE 4-2: The Table Pointer must be manually set to 200000h (base address of the ID locations) once the code memory has been verified. The post-increment feature of the table read, 4-bit command may not be used to increment the Table Pointer beyond the code memory space. In a 128-Kbyte device, for example, a post-increment read of address, 1FFFFh, will wrap the Table Pointer back to 000000h, rather than point to the unimplemented address, 020000h. VERIFY CODE MEMORY FLOW Start Set TBLPTR = 0 Set TBLPTR = 200000h Read Low Byte with Post-Increment Read Low Byte with Post-Increment Read High Byte with Post-Increment Does Word = Expect Data? Increment Pointer No Read High Byte with Post-Increment Does Word = Expect Data? Failure, Report Error Yes No All code memory verified? Yes No Failure, Report Error Yes No All ID locations verified? Yes Done 2011 Microchip Technology Inc. DS39972B-page 31 PIC18FXXK80 FAMILY 4.3 FIGURE 4-3: Verify Configuration Bits READ DATA EEPROM FLOW A configuration address may be read and output on PGD via the 4-bit command, ‘1001’. Configuration data is read and written in a byte-wise fashion, so it is not necessary to merge two bytes into a word prior to a compare. The result may then be immediately compared to the appropriate configuration data in the programmer’s memory for verification. Refer to Section 4.1 “Read Code Memory, ID Locations and Configuration Bits” for implementation details of reading configuration data. 4.4 Start Set Address Read Byte Read Data EEPROM Memory Move to TABLAT Data EEPROM is accessed, one byte at a time, via an Address Pointer (register pair, EEADRH:EEADR) and a Data Latch (EEDATA). Data EEPROM is read by loading EEADRH:EEADR with the desired memory location and initiating a memory read by appropriately configuring the EECON1 register (Register 3-1). The data will be loaded into EEDATA, where it may be serially output on PGD via the 4-bit command, ‘0010’ (Shift Out Data Holding register). A delay of P6 must be introduced after the falling edge of the 8th PGC of the operand to allow PGD to transition from an input to an output. During this time, PGC must be held low (see Figure 4-4). Shift Out Data No Done? Yes Done The command sequence to read a single byte of data is shown in Table 4-2. TABLE 4-2: READ DATA EEPROM MEMORY 4-Bit Command Data Payload Core Instruction Step 1: Direct access to data EEPROM. 0000 0000 9E 7F 9C 7F BCF BCF EECON1, EEPGD EECON1, CFGS Step 2: Set the data EEPROM Address Pointer. 0000 0000 0000 0000 0E 6E OE 6E <Addr> 74 <AddrH> 75 MOVLW MOVWF MOVLW MOVWF <Addr> EEADR <AddrH> EEADRH BSF EECON1, RD Step 3: Initiate a memory read. 0000 80 7F Step 4: Load data into the Serial Data Holding register. 0000 0000 0000 0010 Note 1: 50 73 6E F5 00 00 <MSB><LSB> MOVF EEDATA, W, 0 MOVWF TABLAT NOP Shift Out Data(1) The <LSB> is undefined; the <MSB> is the data. DS39972B-page 32 2011 Microchip Technology Inc. PIC18FXXK80 FAMILY FIGURE 4-4: 1 SHIFT OUT DATA HOLDING REGISTER TIMING (‘0010’) 2 3 4 1 2 3 4 5 6 7 9 8 10 11 12 13 14 15 16 1 2 3 4 PGC P5 P5A P6 P14 PGD 0 1 0 LSb 1 0 2 3 4 5 6 MSb 4.5 Verify Data EEPROM A data EEPROM address may be read via a sequence of core instructions (4-bit command, ‘0000’) and then output on PGD via the 4-bit command, ‘0010’ (TABLAT register). The result may then be immediately compared to the appropriate data in the programmer’s memory for verification. Refer to Section 4.4 “Read Data EEPROM Memory” for implementation details of reading data EEPROM. 4.6 n n n Fetch Next 4-Bit Command Shift Data Out PGD = Input n PGD = Output PGD = Input Given that Blank Checking is merely code and data EEPROM verification with FFh expect data, refer to Section 4.4 “Read Data EEPROM Memory” and Section 4.2 “Verify Code Memory and ID Locations” for implementation details. FIGURE 4-5: BLANK CHECK FLOW Start Blank Check The term, “Blank Check”, means to verify that the device has no programmed memory cells. All memories must be verified: code memory, data EEPROM, ID locations and Configuration bits. The Device ID registers (3FFFFEh:3FFFFFh) should be ignored. A “blank” or “erased” memory cell will read as a ‘1’. So, Blank Checking a device merely means to verify that all bytes read as FFh, except the Configuration bits. Unused (reserved) Configuration bits will read ‘0’ (programmed). Refer to Table 5-1 for blank configuration expect data for the various PIC18FXXK80 family devices. 2011 Microchip Technology Inc. Blank Check Device Is device blank? Yes Continue No Abort DS39972B-page 33 PIC18FXXK80 FAMILY 5.0 CONFIGURATION WORD 5.1 The PIC18FXXK80 family of devices has several Configuration Words. These bits can be set or cleared to select various device configurations. All other memory areas should be programmed and verified prior to setting the Configuration Words. These bits may be read out normally, even after read or code protection. See Table 5-1 for a list of Configuration bits and Device IDs, and Table 5-3 for the Configuration bit descriptions. TABLE 5-1: ID Locations A user may store Identification (ID) information in eight ID locations, mapped in 200000h:200007h. It is recommended that the most significant nibble of each ID be Fh. In doing so, if the user code inadvertently tries to execute from the ID space, the ID data will execute as a NOP. CONFIGURATION BITS AND DEVICE IDs File Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 300000h CONFIG1L — XINST — 300001h CONFIG1H IESO FCMEN — 300002h CONFIG2L — BORPW1 BORPW0 BORV1 BORV0 300003h CONFIG2H — WDTPS4 WDTPS3 WDTPS2 WDTPS1 300005h CONFIG3H MCLRE — — — 300006h CONFIG4L DEBUG — — BBSIZ — — 300008h CONFIG5L — — — — CP3 CP2 300009h CONFIG5H CPD CPB — — — — 30000Ah CONFIG6L — — — — WRT3 WRT2 30000Bh CONFIG6H WRTD WRTB WRTC — — — 30000Ch CONFIG7L — — — — EBTR3 EBTR2 30000Dh CONFIG7H — EBTRB — — — — DEV2 DEV1 DEV0 REV4 REV3 DEV10 DEV9 DEV8 DEV7 DEV6 3FFFFEh DEVID1(2) 3FFFFFh Legend: Note 1: 2: 3: (2) DEVID2 SOSCSEL1 SOSCSEL0 INTOSCSEL PLLCFG FOSC3 Bit 1 Bit 0 Default/ Unprogrammed Value — RETEN -1-1 11-1 FOSC1 FOSC0 00-0 1000 BOREN1 BOREN0 PWRTEN -111 1111 WDTPS0 WDTEN1 WDTEN0 -111 1111 CANMX 1--- 1111 — STVREN 1--1 ---1 CP1 CP0 ---- 1111 — — 11-- ---- WRT1 WRT0 ---- 1111 — — 111- ---- EBTR1 EBTR0 ---- 1111 — — -1-- ---- REV2 REV1 REV0 xxxx xxxx DEV5 DEV4 DEV3 xxxx xxxx FOSC2 MSSPMSK T3CKMX(1,3) T0CKMX(1) x = unknown, u = unchanged, — = unimplemented, q = value depends on condition. Shaded cells are unimplemented, read as ‘0’. Only implemented in 64-pin devices. See Register 28-13 in the “PIC18F66K80 Family Data Sheet” for DEVID1 values. DEVID registers are read-only and cannot be programmed by the user. This bit must be maintained as ‘0’ on 28-pin PIC18F2XK80 and 40/44-pin PIC18F4XK80 devices. DS39972B-page 34 2011 Microchip Technology Inc. PIC18FXXK80 FAMILY 5.2 Device ID Word The Device ID word (DEVID<2:1>) for the PIC18FXXK80 family of devices is located at 3FFFFEh:3FFFFFh. These bits may be used by the programmer to identify what device type is being programmed and read out normally, even after code or read protection. See Table 5-2 for a complete list of Device ID values. FIGURE 5-1: READ DEVICE ID WORD FLOW Start Set TBLPTR = 3FFFFE Read Low Byte with Post-Increment Read High Byte with Post-Increment TABLE 5-2: Device DEVICE ID VALUE Device ID Value DEVID2 DEVID1 PIC18F66K80 60h 111x xxxx PIC18F46K80 61h 000x xxxx PIC18F26K80 61h 001x xxxx PIC18F65K80 61h 010x xxxx PIC18F45K80 61h 011x xxxx PIC18F25K80 61h 100x xxxx PIC18LF66K80 61h 110x xxxx PIC18LF46K80 61h 111x xxxx PIC18LF26K80 62h 000x xxxx PIC18LF65K80 62h 001x xxxx PIC18LF45K80 62h 010x xxxx PIC18LF25K80 62h 011x xxxx Note: The ‘x’s in DEVID1 contain the device revision code. Done 2011 Microchip Technology Inc. DS39972B-page 35 PIC18FXXK80 FAMILY TABLE 5-3: Bit Name PIC18FXXK80 FAMILY CONFIGURATION BIT DESCRIPTIONS Configuration Words Description XINST CONFIG1L Extended Instruction Set Enable bit 1 = Instruction set extension and Indexed Addressing mode enabled 0 = Instruction set extension and Indexed Addressing mode disabled (Legacy mode) SOSCSEL<1:0> CONFIG1L SOSC Power Selection and Mode Configuration bits 11 = High-power SOSC circuit selected 10 = Digital (SCLKI) mode 01 = Low-power SOSC circuit selected 00 = Reserved INTOSCSEL CONFIG1L LF-INTOSC Low-Power Enable bit 1 = LF-INTOSC in High-Power mode during Sleep 0 = LF-INTOSC in Low-Power mode during Sleep RETEN CONFIG1L VREG Sleep Enable bit 1 = Ultra low-power regulator is disabled. Regulator power in Sleep mode is controlled by VREGSLP (WDTCON<7>). 0 = Ultra low-power regulator is enabled. Regulator power in Sleep mode is controlled by SRETEN (WDTCON<4>). IESO CONFIG1H Internal External Switchover bit 1 = Two-Speed Start-up is enabled 0 = Two-Speed Start-up is disabled FCMEN CONFIG1H Fail-Safe Clock Monitor Enable bit 1 = Fail-Safe Clock Monitor is enabled 0 = Fail-Safe Clock Monitor is disabled PLLCFG CONFIG1H 4 x PLL Enable bit 1 = Oscillator is multiplied by 4 0 = Oscillator is used directly FOSC<3:0> CONFIG1H Oscillator Selection bits 1101 = EC1, EC oscillator (low power, DC-160 kHz) 1100 = EC1IO, EC oscillator with CLKOUT function on RA6 (low power, DC-160 kHz) 1011 = EC2, EC oscillator (medium power, 160 kHz-16 MHz) 1010 = EC2IO, EC oscillator with CLKOUT function on RA6 (medium power, 160 kHz-16 MHz) 1001 = INTIO1 internal RC oscillator with CLKOUT function on RA6 1000 = INTIO2 internal RC oscillator 0111 = RC external RC oscillator 0110 = RCIO external RC oscillator with CKLOUT function on RA6 0101 = EC3, EC oscillator (high power, 16 MHz-64 MHz) 0100 = EC3IO, EC oscillator with CLKOUT function on RA6 (high power, 16 MHz-64 MHz) 0011 = HS1, HS oscillator (medium power, 4 MHz-16 MHz) 0010 = HS2, HS oscillator (high power, 16 MHz-25 MHz) 0001 = XT oscillator 0000 = LP oscillator BORPWR<1:0> CONFIG2L BORMV Power Level bits 11 = ZPBORMV instead of BORMV is selected 10 = BORMV is set to high-power level 01 = BORMV is set to medium power level 00 = BORMV is set to low-power level BORV<1:0> CONFIG2L Brown-out Reset Voltage bits 11 = VBOR set to 1.8V 10 = VBOR set to 2.0V 01 = VBOR set to 2.7V 00 = VBOR set to 3.0V Note 1: 2: 3: The BBSIZ bit cannot be changed once any of the following code-protect bits are enabled: CPB or CP0, WRTB or WRT0, EBTRB or EBTR0. Available on PIC18F6XKXX devices only. This bit must be maintained as ‘0’ on 28-pin PIC18F2XK80 and 40-pin PIC18F4XK80 devices. DS39972B-page 36 2011 Microchip Technology Inc. PIC18FXXK80 FAMILY TABLE 5-3: Bit Name PIC18FXXK80 FAMILY CONFIGURATION BIT DESCRIPTIONS (CONTINUED) Configuration Words Description BOREN<1:0> CONFIG2L Brown-out Reset Enable bits 11 = Brown-out Reset is enabled in hardware only (SBOREN is disabled) 10 = Brown-out Reset is enabled in hardware only and disabled in Sleep mode (SBOREN is disabled) 01 = Brown-out Reset is enabled and controlled by software (SBOREN is enabled) 00 = Brown-out Reset is disabled in hardware and software PWRTEN CONFIG2L Power-up Timer Enable bit 1 = PWRT is disabled 0 = PWRT is enabled WDTPS<4:0> CONFIG2H Watchdog Timer Postscale Select bits 10101-11111: Reserved 10100 = 1:1048576 10011 = 1:524288 10010 = 1:262144 10001 = 1:131072 10000 = 1:65536 01111 = 1:32,768 01110 = 1:16,384 01101 = 1:8,192 01100 = 1:4,096 01011 = 1:2,048 01010 = 1:1,024 01001 = 1:512 01000 = 1:256 00111 = 1:128 00110 = 1:64 00101 = 1:32 00100 = 1:16 00011 = 1:8 00010 = 1:4 00001 = 1:2 00000 = 1:1 WDTEN<1:0> CONFIG2H Watchdog Timer Enable bits 11 = WDT is enabled in hardware; SWDTEN bit is disabled 10 = WDT is controlled with the SWDTEN bit setting 01 = WDT is enabled only while device is active and disabled in Sleep; SWDTEN bit is disabled 00 = WDT is disabled in hardware; SWDTEN bit is disabled MCLRE CONFIG3H MCLR Pin Enable bit 1 = MCLR pin is enabled, RE3 input pin is disabled 0 = RE3 input pin is enabled, MCLR pin is disabled MSSPMSK CONFIG3H MSSP V3 7-Bit Address Masking Mode Enable bit 1 = 7-Bit Address Masking mode enable 0 = 5-Bit Address Masking mode enable T3CKMX(2,3) CONFIG3H Timer3 Clock Input MUX bit 1 = Timer3 gets its clock input from the T1CKI input when T3CON(SOSCEN) = 0 0 = Timer3 gets its clock input from the T3CKI input when T3CON(SOSCEN) = 0 T0CKMX(2) CONFIG3H Timer0 Clock Input MUX bit 1 = Timer0 gets its clock input from the RB5/T0CKI pin 0 = Timer0 gets its clock input from the RG4/T0CKI pin CANMX CONFIG3H ECAN MUX bit 1 = ECAN TX and RX pins are located on RB2 and RB3, respectively 0 = ECAN TX and RX pins are located on RC6 and RC7, respectively (28-pin and 44-pin packages) or on RE5 and RE4, respectively (64-pin package) Note 1: 2: 3: The BBSIZ bit cannot be changed once any of the following code-protect bits are enabled: CPB or CP0, WRTB or WRT0, EBTRB or EBTR0. Available on PIC18F6XKXX devices only. This bit must be maintained as ‘0’ on 28-pin PIC18F2XK80 and 40-pin PIC18F4XK80 devices. 2011 Microchip Technology Inc. DS39972B-page 37 PIC18FXXK80 FAMILY TABLE 5-3: Bit Name PIC18FXXK80 FAMILY CONFIGURATION BIT DESCRIPTIONS (CONTINUED) Configuration Words Description DEBUG CONFIG4L Background Debugger Enable bit 1 = Background debugger is disabled, RB6 and RB7 are configured as general purpose I/O pins 0 = Background debugger is enabled, RB6 and RB7 are dedicated to In-Circuit Debug BBSIZ(1) CONFIG4L Boot Block Size Select bit 1 = 2K word Boot Block size 0 = 1K word Boot Block size STVREN CONFIG4L Stack Overflow/Underflow Reset Enable bit 1 = Reset on stack overflow/underflow is enabled 0 = Reset on stack overflow/underflow is disabled CP3 CONFIG5L Code Protection bit (Block 3 code memory area) 1 = Block 3 is not code-protected 0 = Block 3 is code-protected CP2 CONFIG5L Code Protection bit (Block 2 code memory area) 1 = Block 2 is not code-protected 0 = Block 2 is code-protected CP1 CONFIG5L Code Protection bit (Block 1 code memory area) 1 = Block 1 is not code-protected 0 = Block 1 is code-protected CP0 CONFIG5L Code Protection bit (Block 0 code memory area) 1 = Block 0 is not code-protected 0 = Block 0 is code-protected CPD CONFIG5H Code Protection bit (Data EEPROM) 1 = Data EEPROM is not code-protected 0 = Data EEPROM is code-protected CPB CONFIG5H Code Protection bit (Boot Block memory area) 1 = Boot Block is not code-protected 0 = Boot Block is code-protected WRT3 CONFIG6L Write Protection bit (Block 3 code memory area) 1 = Block 3 is not write-protected 0 = Block 3 is write-protected WRT2 CONFIG6L Write Protection bit (Block 2 code memory area) 1 = Block 2 is not write-protected 0 = Block 2 is write-protected WRT1 CONFIG6L Write Protection bit (Block 1 code memory area) 1 = Block 1 is not write-protected 0 = Block 1 is write-protected WRT0 CONFIG6L Write Protection bit (Block 0 code memory area) 1 = Block 0 is not write-protected 0 = Block 0 is write-protected WRTD CONFIG6H Write Protection bit (Data EEPROM) 1 = Data EEPROM is not write-protected 0 = Data EEPROM is write-protected WRTB CONFIG6H Write Protection bit (Boot Block memory area) 1 = Boot Block is not write-protected 0 = Boot Block is write-protected WRTC CONFIG6H Write Protection bit (Configuration registers) 1 = Configuration registers are not write-protected 0 = Configuration registers are write-protected EBTR3 CONFIG7L Table Read Protection bit (Block 3 code memory area) 1 = Block 3 is not protected from table reads executed in other blocks 0 = Block 3 is protected from table reads executed in other blocks Note 1: 2: 3: The BBSIZ bit cannot be changed once any of the following code-protect bits are enabled: CPB or CP0, WRTB or WRT0, EBTRB or EBTR0. Available on PIC18F6XKXX devices only. This bit must be maintained as ‘0’ on 28-pin PIC18F2XK80 and 40-pin PIC18F4XK80 devices. DS39972B-page 38 2011 Microchip Technology Inc. PIC18FXXK80 FAMILY TABLE 5-3: Bit Name PIC18FXXK80 FAMILY CONFIGURATION BIT DESCRIPTIONS (CONTINUED) Configuration Words Description EBTR2 CONFIG7L Table Read Protection bit (Block 2 code memory area) 1 = Block 2 is not protected from table reads executed in other blocks 0 = Block 2 is protected from table reads executed in other blocks EBTR1 CONFIG7L Table Read Protection bit (Block 1 code memory area) 1 = Block 1 is not protected from table reads executed in other blocks 0 = Block 1 is protected from table reads executed in other blocks EBTR0 CONFIG7L Table Read Protection bit (Block 0 code memory area) 1 = Block 0 is not protected from table reads executed in other blocks 0 = Block 0 is protected from table reads executed in other blocks EBTRB CONFIG7H Table Read Protection bit (Boot Block memory area) 1 = Boot Block is not protected from table reads executed in other blocks 0 = Boot Block is protected from table reads executed in other blocks DEV<10:3> DEVID2 Device ID bits These bits are used with the DEV<2:0> bits in the DEVID1 register to identify the part number. DEV<2:0> DEVID1 Device ID bits These bits are used with the DEV<10:3> bits in the DEVID2 register to identify the part number. REV<4:0> DEVID1 Revision ID bits These bits are used to indicate the revision of the device. Note 1: 2: 3: The BBSIZ bit cannot be changed once any of the following code-protect bits are enabled: CPB or CP0, WRTB or WRT0, EBTRB or EBTR0. Available on PIC18F6XKXX devices only. This bit must be maintained as ‘0’ on 28-pin PIC18F2XK80 and 40-pin PIC18F4XK80 devices. 2011 Microchip Technology Inc. DS39972B-page 39 PIC18FXXK80 FAMILY 5.3 Embedding Configuration Word Information in the HEX File To allow portability of code, a PIC18FXXK80 device programmer is required to read the Configuration Word locations from the hex file. If Configuration Word information is not present in the hex file, then a simple warning message should be issued. Similarly, while saving a hex file, all Configuration Word information must be included. An option to not include the Configuration Word information may be provided. When embedding Configuration Word information in the hex file, it should start at address, 300000h. Microchip Technology Inc. feels strongly that this feature is important for the benefit of the end customer. 5.4 Embedding Data EEPROM Information in the HEX File To allow portability of code, a PIC18FXXK80 device programmer is required to read the data EEPROM information from the hex file. If data EEPROM information is not present, a simple warning message should be issued. Similarly, when saving a hex file, all data EEPROM information must be included. An option to not include the data EEPROM information may be provided. When embedding data EEPROM information in the hex file, it should start at address, F00000h. 5.5 Checksum Computation The checksum is calculated by summing the following: • The contents of all code memory locations • The Configuration Word, appropriately masked • ID locations. The Least Significant 16 bits of this sum are the checksum. Table 5-4 (starting on Page 41) describes how to calculate the checksum for each device. For these examples, the ID memory has been set to ‘Use Unprotected Checksum’ in MPLAB IDE®. Please use this value to determine the value of the ‘SUM(IDs)’ term for each appropriate code-protected example. Note: The checksum calculation differs depending on the code-protect setting. Since the code memory locations read out differently depending on the code-protect setting, the table describes how to manipulate the actual code memory values to simulate the values that would be read from a protected device. When calculating a checksum by reading a device, the entire code memory can simply be read and summed. The Configuration Word and ID locations can always be read. Microchip Technology Inc. believes that this feature is important for the benefit of the end customer. DS39972B-page 40 2011 Microchip Technology Inc. PIC18FXXK80 FAMILY TABLE 5-4: Device CHECKSUM COMPUTATION Code-Protect Checksum Blank Value 0xAA at 0 and Max Address None SUM(0000:0FFF) + SUM(1000:3FFF) + SUM(4000:7FFF) + SUM(8000:BFFF) + SUM(C000:FFFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=8F & 8F) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0F & 0F) + (CONFIG5H=C0 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) 0x0490 0x03E6 Boot Block 2K word SUM(1000:3FFF) + SUM(4000:7FFF) + SUM(8000:BFFF) + SUM(C000:FFFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=8F & 8F) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0F & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) 0x145D 0x1412 0x845A 0x840F (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=8F & 8F) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=00 & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) 0x044E 0x0458 SUM(0000:0FFF) + SUM(1000:1FFF) + SUM(2000:3FFF) + SUM(4000:5FFF) + SUM(6000:7FFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=8F & 8F) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0F & 0F) + (CONFIG5H=C0 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) 0x8490 0x83E6 SUM(1000:1FFF) + SUM(2000:3FFF) + SUM(4000:5FFF) + SUM(6000:7FFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=8F & 8F) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0F & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) 0x9465 0x941A 0xC462 0xC417 0x0456 0x0460 PIC18F66K80 Boot/Panel0/ SUM(8000:BFFF) + SUM(C000:FFFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + Panel1 (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=8F & 8F) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0C & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) All None Boot Block 2K word PIC18F65K80 Boot/Panel0/ SUM(4000:5FFF) + SUM(6000:7FFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + Panel1 (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=8F & 8F) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0C & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) All (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=8F & 8F) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=00 & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) 2011 Microchip Technology Inc. DS39972B-page 41 PIC18FXXK80 FAMILY TABLE 5-4: Device CHECKSUM COMPUTATION (CONTINUED) Code-Protect Checksum Blank Value 0xAA at 0 and Max Address None SUM(0000:0FFF) + SUM(1000:3FFF) + SUM(4000:7FFF) + SUM(8000:BFFF) + SUM(C000:FFFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=89 & 89) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0F & 0F) + (CONFIG5H=C0 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) 0x048A 0x03E0 Boot Block 2K word SUM(1000:3FFF) + SUM(4000:7FFF) + SUM(8000:BFFF) + SUM(C000:FFFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=89 & 89) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0F & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) 0x1460 0x1406 0x845D 0x8403 (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=89 & 89) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=00 & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) 0x0451 0x044C None SUM(0000:0FFF) + SUM(1000:1FFF) + SUM(2000:3FFF) + SUM(4000:5FFF) + SUM(6000:7FFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=89 & 89) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0F & 0F) + (CONFIG5H=C0 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) 0x848A 0x83E0 Boot Block 2K word SUM(1000:1FFF) + SUM(2000:3FFF) + SUM(4000:5FFF) + SUM(6000:7FFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=89 & 89) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0F & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) 0x9468 0x940E 0xC465 0xC40B 0x0459 0x0454 PIC18F46K80 Boot/Panel0/ SUM(8000:BFFF) + SUM(C000:FFFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + Panel1 (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=89 & 89) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0C & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) All PIC18F45K80 Boot/Panel0/ SUM(4000:5FFF) + SUM(6000:7FFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + Panel1 (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=89 & 89) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0C & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) All DS39972B-page 42 (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=89 & 89) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=00 & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) 2011 Microchip Technology Inc. PIC18FXXK80 FAMILY TABLE 5-4: Device CHECKSUM COMPUTATION (CONTINUED) Code-Protect Checksum Blank Value 0xAA at 0 and Max Address None SUM(0000:0FFF) + SUM(1000:3FFF) + SUM(4000:7FFF) + SUM(8000:BFFF) + SUM(C000:FFFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=89 & 89) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0F & 0F) + (CONFIG5H=C0 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) 0x048A 0x03E0 Boot Block 2K word SUM(1000:3FFF) + SUM(4000:7FFF) + SUM(8000:BFFF) + SUM(C000:FFFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=89 & 89) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0F & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) 0x1460 0x1406 0x845D 0x8403 (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=89 & 89) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=00 & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) 0x0451 0x044C None SUM(0000:0FFF) + SUM(1000:1FFF) + SUM(2000:3FFF) + SUM(4000:5FFF) + SUM(6000:7FFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=89 & 89) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0F & 0F) + (CONFIG5H=C0 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) 0x848A 0x83E0 Boot Block 2K word SUM(1000:1FFF) + SUM(2000:3FFF) + SUM(4000:5FFF) + SUM(6000:7FFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=89 & 89) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0F & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) 0x9468 0x940E 0xC465 0xC40B 0x0459 0x0454 PIC18F26K80 Boot/Panel0/ SUM(8000:BFFF) + SUM(C000:FFFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + Panel1 (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=89 & 89) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0C & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) All PIC18F25K80 Boot/Panel0/ SUM(4000:5FFF) + SUM(6000:7FFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + Panel1 (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=89 & 89) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0C & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) All (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=89 & 89) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=00 & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) 2011 Microchip Technology Inc. DS39972B-page 43 PIC18FXXK80 FAMILY TABLE 5-4: Device CHECKSUM COMPUTATION (CONTINUED) Code-Protect Checksum Blank Value 0xAA at 0 and Max Address None SUM(0000:0FFF) + SUM(1000:3FFF) + SUM(4000:7FFF) + SUM(8000:BFFF) + SUM(C000:FFFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=8F & 8F) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0F & 0F) + (CONFIG5H=C0 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) 0x0490 0x03E6 Boot Block 2K word SUM(1000:3FFF) + SUM(4000:7FFF) + SUM(8000:BFFF) + SUM(C000:FFFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=8F & 8F) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0F & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) 0x145D 0x1412 0x845A 0x840F (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=8F & 8F) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=00 & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) 0x044E 0x0458 None SUM(0000:0FFF) + SUM(1000:1FFF) + SUM(2000:3FFF) + SUM(4000:5FFF) + SUM(6000:7FFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=8F & 8F) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0F & 0F) + (CONFIG5H=C0 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) 0x8490 0x83E6 Boot Block 2K word SUM(1000:1FFF) + SUM(2000:3FFF) + SUM(4000:5FFF) + SUM(6000:7FFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=8F & 8F) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0F & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) 0x9465 0x941A 0xC462 0xC417 0x0456 0x0460 PIC18LF66K80 Boot/Panel0/ SUM(8000:BFFF) + SUM(C000:FFFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + Panel1 (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=8F & 8F) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0C & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) All PIC18LF65K80 Boot/Panel0/ SUM(4000:5FFF) + SUM(6000:7FFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + Panel1 (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=8F & 8F) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0C & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) All DS39972B-page 44 (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=8F & 8F) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=00 & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) 2011 Microchip Technology Inc. PIC18FXXK80 FAMILY TABLE 5-4: Device CHECKSUM COMPUTATION (CONTINUED) Code-Protect Checksum Blank Value 0xAA at 0 and Max Address None SUM(0000:0FFF) + SUM(1000:3FFF) + SUM(4000:7FFF) + SUM(8000:BFFF) + SUM(C000:FFFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=89 & 89) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0F & 0F) + (CONFIG5H=C0 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) 0x048A 0x03E0 Boot Block 2K word SUM(1000:3FFF) + SUM(4000:7FFF) + SUM(8000:BFFF) + SUM(C000:FFFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=89 & 89) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0F & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) 0x1460 0x1406 0x845D 0x8403 (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=89 & 89) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=00 & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) 0x0451 0x044C None SUM(0000:0FFF) + SUM(1000:1FFF) + SUM(2000:3FFF) + SUM(4000:5FFF) + SUM(6000:7FFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=89 & 89) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0F & 0F) + (CONFIG5H=C0 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) 0x848A 0x83E0 Boot Block 2K word SUM(1000:1FFF) + SUM(2000:3FFF) + SUM(4000:5FFF) + SUM(6000:7FFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=89 & 89) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0F & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) 0x9468 0x940E 0xC465 0xC40B 0x0459 0x0454 PIC18LF46K80 Boot/Panel0/ SUM(8000:BFFF) + SUM(C000:FFFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + Panel1 (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=89 & 89) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0C & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) All PIC18LF45K80 Boot/Panel0/ SUM(4000:5FFF) + SUM(6000:7FFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + Panel1 (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=89 & 89) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0C & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) All (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=89 & 89) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=00 & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) 2011 Microchip Technology Inc. DS39972B-page 45 PIC18FXXK80 FAMILY TABLE 5-4: Device CHECKSUM COMPUTATION (CONTINUED) Code-Protect Checksum Blank Value 0xAA at 0 and Max Address None SUM(0000:0FFF) + SUM(1000:3FFF) + SUM(4000:7FFF) + SUM(8000:BFFF) + SUM(C000:FFFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=89 & 89) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0F & 0F) + (CONFIG5H=C0 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) 0x048A 0x03E0 Boot Block 2K word SUM(1000:3FFF) + SUM(4000:7FFF) + SUM(8000:BFFF) + SUM(C000:FFFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=89 & 89) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0F & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) 0x1460 0x1406 0x845D 0x8403 (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=89 & 89) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=00 & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) 0x0451 0x044C None SUM(0000:0FFF) + SUM(1000:1FFF) + SUM(2000:3FFF) + SUM(4000:5FFF) + SUM(6000:7FFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=89 & 89) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0F & 0F) + (CONFIG5H=C0 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) 0x848A 0x83E0 Boot Block 2K word SUM(1000:1FFF) + SUM(2000:3FFF) + SUM(4000:5FFF) + SUM(6000:7FFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=89 & 89) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0F & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) 0x9468 0x940E 0xC465 0xC40B 0x0459 0x0454 PIC18LF26K80 Boot/Panel0/ SUM(8000:BFFF) + SUM(C000:FFFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + Panel1 (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=89 & 89) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0C & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) All PIC18LF25K80 Boot/Panel0/ SUM(4000:5FFF) + SUM(6000:7FFF) + (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + Panel1 (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=89 & 89) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=0C & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) All DS39972B-page 46 (CONFIG1L=5D & 5D) + (CONFIG1H=08 & DF) + (CONFIG2L=7F & 7F) + (CONFIG2H=7F & 7F) + (CONFIG3L=00 & 00) + (CONFIG3H=89 & 89) + (CONFIG4L=91 & 91) + (CONFIG4H=00 & 00) + (CONFIG5L=00 & 0F) + (CONFIG5H=80 & C0) + (CONFIG6L=0F & 0F) + (CONFIG6H=E0 & E0) + (CONFIG7L=0F & 0F) + (CONFIG7H=40 & 40) + SUM(IDs) 2011 Microchip Technology Inc. PIC18FXXK80 FAMILY 6.0 AC/DC CHARACTERISTICS TIMING REQUIREMENTS FOR PROGRAM/VERIFY TEST MODE Standard Operating Conditions Operating Temperature: 25C is recommended Param No. Sym Characteristic D110 VIHH High-Voltage Programming Voltage on MCLR/VPP/RE3 D111 VDD Supply Voltage during Programming Min Max Units Conditions VDD + 1.5 9 V 2.1 5.5 V Row Erase/Write for “F” parts 2.7 5.5 V Block Erase operations for “F” parts 2.1 3.6 V Row Erase/Write for “LF” parts 2.7 3.6 V Block Erase operations for “LF” parts D112 IPP Programming Current on MCLR/VPP/RE3 — 600 A D113 IDDP Supply Current during Programming — 3.0 mA D031 VIL Input Low Voltage VSS 0.2 VDD V D041 VIH Input High Voltage 0.8 VDD VDD V D080 VOL Output Low Voltage — 0.6 V IOL = 8.5 mA @ 4.5V D090 VOH Output High Voltage VDD – 0.7 — V IOH = -3.0 mA @ 4.5V D012 CIO Capacitive Loading on I/O Pin (PGD) — 50 pF To meet AC specifications P1 TR MCLR/VPP/RE3 Rise Time to Enter Program/Verify mode — 1.0 s (Note 1) P2 TPGC Serial Clock (PGC) Period 100 — ns VDD = 5.0V 1 — s VDD = 2.0V P2A TPGCL Serial Clock (PGC) Low Time 40 — ns VDD = 5.0V 400 — ns VDD = 2.0V P2B TPGCH Serial Clock (PGC) High Time 40 — ns VDD = 5.0V 400 — ns VDD = 2.0V P3 TSET1 Input Data Setup Time to Serial Clock 15 — ns P4 THLD1 Input Data Hold Time from PGC 15 — ns P5 TDLY1 Delay between 4-Bit Command and Command Operand 40 — ns P5A TDLY1A Delay between 4-Bit Command Operand and Next 4-Bit Command 40 — ns P6 TDLY2 Delay between Last PGC of Command Byte to First PGC of Read of Data Word 20 — ns P9 TDLY5 PGC High Time (minimum programming time) 1 — ms Externally timed P9A TDLY5A PGC High Time 5 — ms Configuration Word programming time P10 TDLY6 100 — s Note 1: PGC Low Time after Programming (high-voltage discharge time) Do not allow excess time when transitioning MCLR between VIL and VIHH; this can cause spurious program executions to occur. The maximum transition time is: 1 TCY + TPWRT (if enabled) + 1024 TOSC (for LP, HS, HS/PLL and XT modes only) + 2 ms (for HS/PLL mode only) + 1.5 s (for EC mode only) where TCY is the instruction cycle time, TPWRT is the Power-up Timer period and TOSC is the oscillator period. For specific values, refer to the Electrical Characteristics section of the device data sheet for the particular device. 2011 Microchip Technology Inc. DS39972B-page 47 PIC18FXXK80 FAMILY 6.0 AC/DC CHARACTERISTICS TIMING REQUIREMENTS FOR PROGRAM/VERIFY TEST MODE (CONTINUED) Standard Operating Conditions Operating Temperature: 25C is recommended Param No. Sym Characteristic P11 TDLY7 Delay to allow Self-Timed Data Write or Block Erase to Occur P11A TDRWT Data Write Polling Time Min Max Units 5 — ms 4 — ms P12 THLD2 Input Data Hold Time from MCLR/VPP/RE3 250 — s P13 TSET2 VDD Setup Time to MCLR/VPP/RE3 100 — ns P14 TVALID Data Out Valid from PGC 10 — ns P15 TDLY8 Delay between Last PGC and MCLR/VPP/RE3 0 — s P16 THLD3 MCLR/VPP/RE3 to VDD — 100 ns P17 THLD3 MCLR/VPP/RE3 to VDD — 100 ns Note 1: Conditions Do not allow excess time when transitioning MCLR between VIL and VIHH; this can cause spurious program executions to occur. The maximum transition time is: 1 TCY + TPWRT (if enabled) + 1024 TOSC (for LP, HS, HS/PLL and XT modes only) + 2 ms (for HS/PLL mode only) + 1.5 s (for EC mode only) where TCY is the instruction cycle time, TPWRT is the Power-up Timer period and TOSC is the oscillator period. For specific values, refer to the Electrical Characteristics section of the device data sheet for the particular device. DS39972B-page 48 2011 Microchip Technology Inc. PIC18FXXK80 FAMILY APPENDIX A: REVISION HISTORY Revision A (March 2010) Original programming specification PIC18FXXK80 family devices. for the Revision B (January 2011) Updated Section 2.3 “On-Chip Voltage Regulator” with correct capacitor information. Updated Table 5-4 and Section 6.0 “AC/DC Characteristics Timing Requirements for Program/Verify Test Mode”. Minor grammatical corrections made throughout text. 2011 Microchip Technology Inc. DS39972B-page 49 PIC18FXXK80 FAMILY NOTES: DS39972B-page 50 2011 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, PIC32 logo, rfPIC and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, MXDEV, MXLAB, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Application Maestro, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP, Mindi, MiWi, MPASM, MPLAB Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE, rfLAB, Select Mode, Total Endurance, TSHARC, UniWinDriver, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. © 2011, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. ISBN: 978-1-60932-837-5 Microchip received ISO/TS-16949:2002 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified. 2011 Microchip Technology Inc. DS39972B-page 51 Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://support.microchip.com Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4123 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Japan - Yokohama Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Kokomo Kokomo, IN Tel: 765-864-8360 Fax: 765-864-8387 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8528-2100 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 China - Chongqing Tel: 86-23-8980-9588 Fax: 86-23-8980-9500 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 China - Hong Kong SAR Tel: 852-2401-1200 Fax: 852-2401-3431 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 Taiwan - Hsin Chu Tel: 886-3-6578-300 Fax: 886-3-6578-370 China - Shenzhen Tel: 86-755-8203-2660 Fax: 86-755-8203-1760 Taiwan - Kaohsiung Tel: 886-7-213-7830 Fax: 886-7-330-9305 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 08/04/10 DS39972B-page 52 2011 Microchip Technology Inc.