TI TXB0104PWR

TXB0104
www.ti.com
SCES650E – APRIL 2006 – REVISED FEBRUARY 2010
4-BIT BIDIRECTIONAL VOLTAGE-LEVEL TRANSLATOR
WITH AUTOMATIC DIRECTION SENSING AND ±15-kV ESD PROTECTION
Check for Samples: TXB0104
FEATURES
1
•
•
•
•
•
1.2 V to 3.6 V on A Port and 1.65 V to 5.5 V on
B Port (VCCA ≤ VCCB)
VCC Isolation Feature – If Either VCC Input Is at
GND, All Outputs Are in the High-Impedance
State
OE Input Circuit Referenced to VCCA
Low Power Consumption, 5-mA Max ICC
Ioff Supports Partial-Power-Down Mode
Operation
•
•
Latch-Up Performance Exceeds 100 mA Per
JESD 78, Class II
ESD Protection Exceeds JESD 22
– A Port
– 2500-V Human-Body Model (A114-B)
– 1500-V Charged-Device Model (C101)
– B Port
– ±15-kV Human-Body Model (A114-B)
– 1500-V Charged-Device Model (C101)
GXU/ZXU PACKAGE
(TOP VIEW)
A
TERMINAL ASSIGNMENTS
(GXU/ZXU Package)
B C
4
3
2
A
B
C
4
A4
GND
B4
3
A3
OE
B3
2
A2
VCCA
B2
1
A1
VCCB
B1
1
A1
2
13
B1
A2
3
12
B2
A3
4
11
B3
A4
5
10
B4
NC
GND
6
9
7
8
NC
OE
A1
A2
A3
A4
NC
1
14
OE
VCCB
RUT PACKAGE
(TOP VIEW)
VCCA
13 B1
2
3
Exposed
Center
Pad
4
5
6
12 B2
11 B3
10 B4
9 NC
7
8
1
12
11 VCCB
A1 2
10 B1
A2 3
9 B2
A3 4
8 B3
A4 5
6
7 B4
GND
14
OE
1
GND
VCCA
VCCB
D OR PW PACKAGE
(TOP VIEW)
VCCA
RGY PACKAGE
(TOP VIEW)
N.C. − No internal connection
For RGY, if the exposed center pad is used it must only be connected to as a secondary ground or left electrically
open.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2006–2010, Texas Instruments Incorporated
TXB0104
SCES650E – APRIL 2006 – REVISED FEBRUARY 2010
www.ti.com
YZT PACKAGE
(TOP VIEW)
TERMINAL ASSIGNMENTS
(YZT Package)
3
2
1
D
A4
GND
B4
C
A3
OE
B3
B
A2
VCCA
B2
A
A1
VCCB
B1
3 2 1
D
C
B
A
DESCRIPTION/ORDERING INFORMATION
This 4-bit noninverting translator uses two separate configurable power-supply rails. The A port is designed to
track VCCA. VCCA accepts any supply voltage from 1.2 V to 3.6 V. The B port is designed to track VCCB. VCCB
accepts any supply voltage from 1.65 V to 5.5 V. This allows for universal low-voltage bidirectional translation
between any of the 1.2-V, 1.5-V, 1.8-V, 2.5-V, 3.3-V, and 5-V voltage nodes. VCCA should not exceed VCCB.
When the output-enable (OE) input is low, all outputs are placed in the high-impedance state. To ensure the
high-impedance state during power up or power down, OE should be tied to GND through a pulldown resistor;
the minimum value of the resistor is determined by the current-sourcing capability of the driver.
The TXB0104 is designed so that the OE input circuit is supplied by VCCA.
This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs,
preventing damaging current backflow through the device when it is powered down.
ORDERING INFORMATION (1)
PACKAGE (2)
TA
–40°C to 85°C
ORDERABLE PART NUMBER
NanoFree™ — WCSP (DSBGA)
0.23-mm Large Bump – YZT
(Pb-free) 0.625-mm max height
Reel of 3000
TXB0104YZTR
___2K_
UFBGA – GXU
Reel of 2500
TXB0104GXUR
YE04
UFBGA – ZXU (Pb-Free)
Reel of 2500
TXB0104ZXUR
YE04
QFN – RGY
Reel of 1000
uQFN – RUT
Reel of 1000
Tube of 50
SOIC – D
Reel of 2500
TSSOP – PW
(1)
(2)
(3)
2
TOP-SIDE MARKING (3)
Reel of 2000
TXB0104RGYR
TXB0104RGYRG4
TXB0104RUTR
YE04
2KR
TXB0104D
TXB0104DG4
TXB0104DR
TXB0104
TXB0104DRG4
TXB0104PWR
TXB0104PWRG4
YE04
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
YZT: The actual top-side marking has three preceding characters to denote year, month, and sequence code, and one following
character to designate the wafer fab/assembly site. Pin 1 identifier indicates solder-bump composition (1 = SnPb, • = Pb-free).
Submit Documentation Feedback
Copyright © 2006–2010, Texas Instruments Incorporated
Product Folder Link(s): TXB0104
TXB0104
www.ti.com
SCES650E – APRIL 2006 – REVISED FEBRUARY 2010
PIN DESCRIPTION
PIN NO.
D, PW,
OR RGY
BALL NO.
NAME
FUNCTION
RUT
GXU/
ZXU
YZT
1
1
B2
B2
VCCA
2
2
A1
A3
A1
Input/output 1. Referenced to VCCA.
3
3
A2
B3
A2
Input/output 2. Referenced to VCCA.
4
4
A3
C3
A3
Input/output 3. Referenced to VCCA.
5
5
A4
D3
A4
Input/output 4. Referenced to VCCA.
6
–
–
–
NC
No connection. Not internally connected.
7
6
B4
D2
GND
8
12
B3
C2
OE
3-state output-mode enable. Pull OE low to place all outputs in 3-state mode.
Referenced to VCCA.
A-port supply voltage 1.2 V ≤ VCCA ≤ 3.6 V and VCCA ≤ VCCB.
Ground
9
–
–
–
NC
No connection. Not internally connected.
10
7
C4
D1
B4
Input/output 4. Referenced to VCCB.
11
8
C3
C1
B3
Input/output 3. Referenced to VCCB.
12
9
C2
B1
B2
Input/output 2. Referenced to VCCB.
13
10
C1
A1
B1
Input/output 1. Referenced to VCCB.
14
11
B1
A2
VCCB
B-port supply voltage 1.65 V ≤ VCCB ≤ 5.5 V.
ABSOLUTE MAXIMUM RATINGS (1)
over operating free-air temperature range (unless otherwise noted)
VCCA
VCCB
MIN
MAX
–0.5
4.6
–0.5
6.5
A port
–0.5
4.6
B port
–0.5
6.5
A port
–0.5
4.6
B port
-0.5
6.5
A port
–0.5
VCCA + 0.5
B port
–0.5
VCCB + 0.5
Supply voltage range
UNIT
V
VI
Input voltage range
VO
Voltage range applied to any output in the high-impedance or
power-off state
VO
Voltage range applied to any output in the high or low state (2)
IIK
Input clamp current
VI < 0
–50
mA
IOK
Output clamp current
VO < 0
–50
mA
IO
Continuous output current
Continuous current through VCCA, VCCB, or GND
Tstg
(1)
(2)
Storage temperature range
–65
V
V
V
±50
mA
±100
mA
150
°C
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
The value of VCCA and VCCB are provided in the recommended operating conditions table.
Submit Documentation Feedback
Copyright © 2006–2010, Texas Instruments Incorporated
Product Folder Link(s): TXB0104
3
TXB0104
SCES650E – APRIL 2006 – REVISED FEBRUARY 2010
www.ti.com
THERMAL IMPEDANCE RATINGS
UNIT
D package (1)
86
GXU/ZXU package (1)
(1)
(2)
PW package
Package thermal impedance
qJA
°C/W
47
RUT package
TBD
YZT package
90
The package thermal impedance is calculated in accordance with JESD 51-7.
The package thermal impedance is calculated in accordance with JESD 51-5.
(2)
VCCA
VCCA
VCCB
VCCB
Supply voltage
MIN
MAX
1.2
3.6
1.65
5.5
Data inputs
1.2 V to 3.6 V
1.65 V to 5.5 V
VCCI × 0.65 (3)
VCCI
OE
1.2 V to 3.6 V
1.65 V to 5.5 V
VCCA × 0.65
5.5
Data inputs
1.2 V to 5.5 V
1.65 V to 5.5 V
0
VCCI × 0.35 (3)
OE
1.2 V to 3.6 V
1.65 V to 5.5 V
0
VCCA × 0.35
0
3.6
1.2 V to 3.6 V
1.65 V to 5.5 V
0
5.5
1.2 V to 3.6 V
1.65 V to 5.5 V
40
1.65 V to 3.6 V
40
VIH
High-level input voltage
VIL
Low-level input voltage
VO
Voltage range applied to any A-port
output in the high-impedance
B-port
or power-off state
Δt/Δv
Input transition
rise or fall rate
TA
Operating free-air temperature
A-port inputs
4
113
RGY package (2)
RECOMMENDED OPERATING CONDITIONS (1)
(1)
(2)
(3)
129
(1)
B-port inputs
1.2 V to 3.6 V
4.5 V to 5.5 V
UNIT
V
V
V
V
ns/V
30
–40
85
°C
The A and B sides of an unused data I/O pair must be held in the same state, i.e., both at VCCI or both at GND.
VCCA must be less than or equal to VCCB and must not exceed 3.6 V.
VCCI is the supply voltage associated with the input port.
Submit Documentation Feedback
Copyright © 2006–2010, Texas Instruments Incorporated
Product Folder Link(s): TXB0104
TXB0104
www.ti.com
SCES650E – APRIL 2006 – REVISED FEBRUARY 2010
ELECTRICAL CHARACTERISTICS (1)
(2)
over recommended operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VOHA
IOH = –20 mA
VOLA
IOL = 20 mA
VOHB
IOH = –20 mA
VOLB
II
Ioff
IOZ
–40°C to 85°C
TYP MAX
MIN MAX
1.1
V
VCCA – 0.4
1.2 V
0.9
1.4 V to 3.6 V
0.4
1.65 V to 5.5 V
VCCB – 0.4
V
V
0.4
V
±1
±2
mA
VI or VO = 0 to 3.6 V
0V
0 V to 5.5 V
±1
±2
B port
VI or VO = 0 to 5.5 V
0 V to 3.6 V
0V
±1
±2
A or B port
OE = GND
1.2 V to 3.6 V
1.65 V to 5.5 V
±1
±2
1.2 V
1.65 V to 5.5 V
1.4 V to 3.6 V
1.65 V to 5.5 V
5
3.6 V
0V
2
A port
VI = VCCI or GND,
IO = 0
VI = VCCI or GND,
IO = 0
VI = VCCI or GND,
IO = 0
ICCZA
VI = VCCI or GND,
IO = 0,
OE = GND
ICCZB
VI = VCCI or GND,
IO = 0,
OE = GND
OE
A port
B port
1.65 V to 5.5 V
UNIT
1.65 V to 5.5 V
ICCA + ICCB
(1)
(2)
1.2 V
TA = 25°C
MIN
1.2 V to 3.6 V
VI = VCCI or GND
ICCB
Cio
VCCB
1.4 V to 3.6 V
IOL = 20 mA
OE
ICCA
Ci
VCCA
0V
5.5 V
1.65 V to 5.5 V
1.4 V to 3.6 V
1.65 V to 5.5 V
5
3.6 V
0V
–2
0V
5.5 V
2
1.2 V
1.65 V to 5.5 V
1.65 V to 5.5 V
1.2 V
1.65 V to 5.5 V
1.4 V to 3.6 V
1.65 V to 5.5 V
1.2 V
1.65 V to 5.5 V
1.4 V to 3.6 V
1.65 V to 5.5 V
1.2 V to 3.6 V
1.65 V to 5.5 V
1.2 V to 3.6 V
1.65 V to 5.5 V
mA
0.06
1.2 V
1.4 V to 3.6 V
mA
mA
–2
3.4
3.5
10
mA
mA
0.05
5
mA
3.3
5
3
4
5
6
11
14
mA
pF
pF
VCCI is the supply voltage associated with the input port.
VCCO is the supply voltage associated with the output port.
Submit Documentation Feedback
Copyright © 2006–2010, Texas Instruments Incorporated
Product Folder Link(s): TXB0104
5
TXB0104
SCES650E – APRIL 2006 – REVISED FEBRUARY 2010
www.ti.com
TIMING REQUIREMENTS
TA = 25°C, VCCA = 1.2 V
Data rate
tw
Pulse duration
Data inputs
VCCB = 1.8 V
VCCB = 2.5 V
VCCB = 3.3 V
VCCB = 5 V
TYP
TYP
TYP
TYP
20
20
20
20
Mbps
50
50
50
50
ns
UNIT
TIMING REQUIREMENTS
over recommended operating free-air temperature range, VCCA = 1.5 V ± 0.1 V (unless otherwise noted)
VCCB = 1.8 V
± 0.15 V
MIN
Data rate
tw
Pulse duration
VCCB = 2.5 V
± 0.2 V
MAX
MIN
MAX
40
Data inputs
VCCB = 3.3 V
± 0.3 V
MIN
MAX
40
25
VCCB = 5 V
± 0.5 V
MIN
40
25
40
25
UNIT
MAX
25
Mbps
ns
TIMING REQUIREMENTS
over recommended operating free-air temperature range, VCCA = 1.8 V ± 0.15 V (unless otherwise noted)
VCCB = 1.8 V
± 0.15 V
MIN
Data rate
tw
Pulse duration
VCCB = 2.5 V
± 0.2 V
MAX
MIN
MAX
60
Data inputs
17
VCCB = 3.3 V
± 0.3 V
MIN
VCCB = 5 V
± 0.5 V
MAX
60
MIN
60
17
60
17
UNIT
MAX
17
Mbps
ns
TIMING REQUIREMENTS
over recommended operating free-air temperature range, VCCA = 2.5 V ± 0.2 V (unless otherwise noted)
VCCB = 2.5 V
± 0.2 V
MIN
Data rate
tw
Pulse duration
VCCB = 3.3 V
± 0.3 V
MAX
MIN
MAX
100
Data inputs
VCCB = 5 V
± 0.5 V
MIN
100
10
100
10
UNIT
MAX
10
Mbps
ns
TIMING REQUIREMENTS
over recommended operating free-air temperature range, VCCA = 3.3 V ± 0.3 V (unless otherwise noted)
VCCB = 3.3 V
± 0.3 V
MIN
Data rate
tw
6
Pulse duration
VCCB = 5 V
± 0.5 V
MAX
MIN
100
Data inputs
Submit Documentation Feedback
10
UNIT
MAX
100
10
Mbps
ns
Copyright © 2006–2010, Texas Instruments Incorporated
Product Folder Link(s): TXB0104
TXB0104
www.ti.com
SCES650E – APRIL 2006 – REVISED FEBRUARY 2010
SWITCHING CHARACTERISTICS
TA = 25°C, VCCA = 1.2 V
FROM
(INPUT)
TO
(OUTPUT)
VCCB = 1.8 V
VCCB = 2.5 V
VCCB = 3.3 V
VCCB = 5 V
TYP
TYP
TYP
TYP
A
B
6.9
5.7
5.3
5.5
B
A
7.4
6.4
6
5.8
A
1
1
1
1
B
1
1
1
1
A
18
15
14
14
B
20
17
16
16
trA, tfA
A-port rise and fall times
4.2
4.2
4.2
4.2
ns
trB, tfB
B-port rise and fall times
2.1
1.5
1.2
1.1
ns
tSK(O)
Channel-to-channel skew
0.4
0.5
0.5
1.4
ns
20
20
20
20
Mbps
PARAMETER
tpd
ten
OE
tdis
OE
Max data rate
UNIT
ns
ms
ns
SWITCHING CHARACTERISTICS
over recommended operating free-air temperature range, VCCA = 1.5 V ± 0.1 V (unless otherwise noted)
PARAMETER
tpd
FROM
(INPUT)
TO
(OUTPUT)
A
B
ten
OE
tdis
OE
VCCB = 1.8 V
± 0.15 V
VCCB = 2.5 V
± 0.2 V
VCCB = 3.3 V
± 0.3 V
MIN
MAX
MIN
MAX
MIN
B
1.4
12.9
1.2
10.1
A
0.9
14.2
0.7
12
VCCB = 5 V
± 0.5 V
UNIT
MAX
MIN
MAX
1.1
10
0.8
9.9
0.4
11.7
0.3
13.7
A
1
1
1
1
B
1
1
1
1
ns
ms
A
5.9
31
5.7
25.9
5.6
23
5.7
22.4
B
5.4
30.3
4.9
22.8
4.8
20
4.9
19.5
trA, tfA
A-port rise and fall times
1.4
5.1
1.4
5.1
1.4
5.1
1.4
5.1
ns
trB, tfB
B-port rise and fall times
0.9
4.5
0.6
3.2
0.5
2.8
0.4
2.7
ns
tSK(O)
Channel-to-channel skew
Max data rate
0.5
0.5
40
40
0.5
40
0.5
40
ns
ns
Mbps
SWITCHING CHARACTERISTICS
over recommended operating free-air temperature range, VCCA = 1.8 V ± 0.15 V (unless otherwise noted)
PARAMETER
tpd
FROM
(INPUT)
TO
(OUTPUT)
A
B
ten
OE
tdis
OE
VCCB = 1.8 V
± 0.15 V
VCCB = 2.5 V
± 0.2 V
VCCB = 3.3 V
± 0.3 V
VCCB = 5 V
± 0.5 V
UNIT
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
B
1.6
11
1.4
7.7
1.3
6.8
1.2
6.5
A
1.5
12
1.3
8.4
1
7.6
0.9
7.1
A
1
1
1
1
B
1
1
1
1
ns
ms
A
5.9
31
5.1
21.3
5
19.3
5
17.4
B
5.4
30.3
4.4
20.8
4.2
17.9
4.3
16.3
A-port rise and fall times
1
4.2
1.1
4.1
1.1
4.1
1.1
4.1
ns
trB, tfB
B-port rise and fall times
0.9
3.8
0.6
3.2
0.5
2.8
0.4
2.7
ns
tSK(O)
Channel-to-channel skew
trA, tfA
Max data rate
0.5
60
0.5
60
0.5
60
0.5
60
Submit Documentation Feedback
Copyright © 2006–2010, Texas Instruments Incorporated
Product Folder Link(s): TXB0104
ns
ns
Mbps
7
TXB0104
SCES650E – APRIL 2006 – REVISED FEBRUARY 2010
www.ti.com
SWITCHING CHARACTERISTICS
over recommended operating free-air temperature range, VCCA = 2.5 V ± 0.2 V (unless otherwise noted)
PARAMETER
tpd
FROM
(INPUT)
TO
(OUTPUT)
A
B
ten
OE
tdis
OE
VCCB = 2.5 V
± 0.2 V
VCCB = 3.3 V
± 0.3 V
VCCB = 5 V
± 0.5 V
UNIT
MIN
MAX
MIN
MAX
MIN
MAX
B
1.1
6.3
1
5.2
0.9
4.7
A
1.2
6.6
1.1
5.1
0.9
4.4
A
1
1
1
B
1
1
1
A
5.1
21.3
4.6
15.2
4.6
13.2
B
4.4
20.8
3.8
16
3.9
13.9
ns
ms
ns
trA, tfA
A-port rise and fall times
0.8
3
0.8
3
0.8
3
ns
trB, tfB
B-port rise and fall times
0.7
2.6
0.5
2.8
0.4
2.7
ns
tSK(O)
Channel-to-channel skew
0.5
Max data rate
0.5
100
0.5
100
100
ns
Mbps
SWITCHING CHARACTERISTICS
over recommended operating free-air temperature range, VCCA = 3.3 V ± 0.3 V (unless otherwise noted)
PARAMETER
tpd
FROM
(INPUT)
TO
(OUTPUT)
A
B
ten
OE
tdis
OE
VCCB = 5 V
± 0.5 V
UNIT
MIN
MAX
MIN
B
0.9
4.7
0.8
4
A
1
4.9
0.9
3.8
MAX
A
1
1
B
1
1
A
4.6
15.2
4.3
12.1
B
3.8
16
3.4
13.2
ns
ms
ns
trA, tfA
A-port rise and fall times
0.7
2.5
0.7
2.5
ns
trB, tfB
B-port rise and fall times
0.5
2.1
0.4
2.7
ns
tSK(O)
Channel-to-channel skew
0.5
ns
Max data rate
8
VCCB = 3.3 V
± 0.3 V
0.5
100
Submit Documentation Feedback
100
Mbps
Copyright © 2006–2010, Texas Instruments Incorporated
Product Folder Link(s): TXB0104
TXB0104
www.ti.com
SCES650E – APRIL 2006 – REVISED FEBRUARY 2010
OPERATING CHARACTERISTICS
TA = 25°C
VCCA
1.2 V
1.2 V
1.5 V
1.8 V
2.5 V
2.5 V
3.3 V
5V
3.3 V
to
5V
VCCB
PARAMETER
TEST CONDITIONS
5V
CpdA
CpdB
CpdA
CpdB
A-port input, B-port output
B-port input, A-port output
A-port input, B-port output
B-port input, A-port output
A-port input, B-port output
B-port input, A-port output
A-port input, B-port output
B-port input, A-port output
CL = 0, f = 10 MHz,
tr = tf = 1 ns,
OE = VCCA
(outputs enabled)
CL = 0, f = 10 MHz,
tr = tf = 1 ns,
OE = GND
(outputs disabled)
1.8 V
1.8 V
1.8 V
TYP
2.5 V
TYP
TYP
TYP
UNIT
TYP
TYP
TYP
7.8
10
9
8
8
8
9
12
11
11
11
11
11
11
38.1
28
28
28
29
29
29
25.4
19
18
18
19
21
22
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.03
0.01
0.01
0.01
0.01
0.01
0.01
0.04
Submit Documentation Feedback
Copyright © 2006–2010, Texas Instruments Incorporated
Product Folder Link(s): TXB0104
pF
pF
9
TXB0104
SCES650E – APRIL 2006 – REVISED FEBRUARY 2010
www.ti.com
PRINCIPLES OF OPERATION
Applications
The TXB0104 can be used in level-translation applications for interfacing devices or systems operating at
different interface voltages with one another.
Architecture
The TXB0104 architecture (see Figure 1) does not require a direction-control signal to control the direction of
data flow from A to B or from B to A. In a dc state, the output drivers of the TXB0104 can maintain a high or low,
but are designed to be weak, so that they can be overdriven by an external driver when data on the bus starts
flowing the opposite direction.
The output one shots detect rising or falling edges on the A or B ports. During a rising edge, the one shot turns
on the PMOS transistors (T1, T3) for a short duration, which speeds up the low-to-high transition. Similarly,
during a falling edge, the one shot turns on the NMOS transistors (T2, T4) for a short duration, which speeds up
the high-to-low transition. The typical output impedance during output transition is 70 Ω at VCCO = 1.2 V to 1.8 V,
50 Ω at VCCO = 1.8 V to 3.3 V, and 40 Ω at VCCO = 3.3 V to 5 V.
VCCA
VCCB
One
Shot
T1
4k
One
Shot
T2
A
B
One
Shot
T3
4k
T4
One
Shot
Figure 1. Architecture of TXB0104 I/O Cell
Input Driver Requirements
Typical IIN vs VIN characteristics of the TXB0104 are shown in Figure 2. For proper operation, the device driving
the data I/Os of the TXB0104 must have drive strength of at least ±2 mA.
10
Submit Documentation Feedback
Copyright © 2006–2010, Texas Instruments Incorporated
Product Folder Link(s): TXB0104
TXB0104
www.ti.com
SCES650E – APRIL 2006 – REVISED FEBRUARY 2010
IIN
VT/4 kW
VIN
–(VD – VT)/4 kW
A. VT is the input threshold voltage of the TXB0104 (typically VCCI/2).
B. VD is the supply voltage of the external driver.
Figure 2. Typical IIN vs VIN Curve
Power Up
During operation, ensure that VCCA ≤ VCCB at all times. During power-up sequencing, VCCA ≥ VCCB does not
damage the device, so any power supply can be ramped up first. The TXB0104 has circuitry that disables all
output ports when either VCC is switched off (VCCA/B = 0 V).
Enable and Disable
The TXB0104 has an OE input that is used to disable the device by setting OE = low, which places all I/Os in the
high-impedance (Hi-Z) state. The disable time (tdis) indicates the delay between when OE goes low and when the
outputs acutally get disabled (Hi-Z). The enable time (ten) indicates the amount of time the user must allow for the
one-shot circuitry to become operational after OE is taken high.
Pullup or Pulldown Resistors on I/O Lines
The TXB0104 is designed to drive capacitive loads of up to 70 pF. The output drivers of the TXB0104 have low
dc drive strength. If pullup or pulldown resistors are connected externally to the data I/Os, their values must be
kept higher than 50 kΩ to ensure that they do not contend with the output drivers of the TXB0104.
For the same reason, the TXB0104 should not be used in applications such as I2C or 1-Wire where an
open-drain driver is connected on the bidirectional data I/O. For these applications, use a device from the TI
TXS01xx series of level translators.
Submit Documentation Feedback
Copyright © 2006–2010, Texas Instruments Incorporated
Product Folder Link(s): TXB0104
11
TXB0104
SCES650E – APRIL 2006 – REVISED FEBRUARY 2010
www.ti.com
PARAMETER MEASUREMENT INFORMATION
2 × VCCO
From Output
Under Test
15 pF
15 pF
1 MW
Open
50 kW
TEST
tPZL/tPLZ
tPHZ/tPZH
LOAD CIRCUIT FOR
ENABLE/DISABLE
TIME MEASUREMENT
LOAD CIRCUIT FOR MAX DATA RATE,
PULSE DURATION PROPAGATION
DELAY OUTPUT RISE AND FALL TIME
MEASUREMENT
S1
50 kW
From Output
Under Test
S1
2 × VCCO
Open
VCCI
Input
VCCI/2
VCCI/2
0V
tPLH
tPHL
tw
Output
VCCO/2
0.9 y VCCO
0.1 y VCCO
VOH
tf
tr
VCCI
VCCO/2
VOL
Input
VCCI/2
0V
VOLTAGE WAVEFORMS
PULSE DURATION
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
A.
B.
C.
D.
E.
F.
G.
VCCI/2
CL includes probe and jig capacitance.
All input pulses are supplied by generators having the following characteristics: PRRv10 MHz, ZO = 50 Ω, dv/dt ≥ 1 V/ns.
The outputs are measured one at a time, with one transition per measurement.
tPLH and tPHL are the same as tpd.
VCCI is the VCC associated with the input port.
VCCO is the VCC associated with the output port.
All parameters and waveforms are not applicable to all devices.
Figure 3. Load Circuits and Voltage Waveforms
12
Submit Documentation Feedback
Copyright © 2006–2010, Texas Instruments Incorporated
Product Folder Link(s): TXB0104
PACKAGE OPTION ADDENDUM
www.ti.com
17-Sep-2010
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
Samples
(Requires Login)
TXB0104D
ACTIVE
SOIC
D
14
50
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Contact TI Distributor
or Sales Office
TXB0104DG4
ACTIVE
SOIC
D
14
50
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Contact TI Distributor
or Sales Office
TXB0104DR
ACTIVE
SOIC
D
14
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Request Free Samples
TXB0104DRG4
ACTIVE
SOIC
D
14
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Request Free Samples
TXB0104GXUR
ACTIVE
BGA
MICROSTAR
JUNIOR
GXU
12
2500
TBD
TXB0104PWR
ACTIVE
TSSOP
PW
14
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Request Free Samples
TXB0104PWRG4
ACTIVE
TSSOP
PW
14
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Request Free Samples
TXB0104RGYR
ACTIVE
VQFN
RGY
14
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Request Free Samples
TXB0104RGYRG4
ACTIVE
VQFN
RGY
14
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Request Free Samples
TXB0104RUTR
ACTIVE
UQFN
RUT
12
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Request Free Samples
TXB0104YZTR
ACTIVE
DSBGA
YZT
12
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
Request Free Samples
TXB0104ZXUR
ACTIVE
BGA
MICROSTAR
JUNIOR
ZXU
12
2500
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
Request Free Samples
(1)
SNPB
Level-1-240C-UNLIM
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
Addendum-Page 1
Contact TI Distributor
or Sales Office
PACKAGE OPTION ADDENDUM
www.ti.com
17-Sep-2010
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TXB0104 :
• Automotive: TXB0104-Q1
NOTE: Qualified Version Definitions:
• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
25-Mar-2011
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
TXB0104DR
Package Package Pins
Type Drawing
SOIC
TXB0104GXUR
BGA MI
CROSTA
R JUNI
OR
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
D
14
2500
330.0
16.4
6.5
9.0
2.1
8.0
16.0
Q1
GXU
12
2500
330.0
8.4
2.3
2.8
1.0
4.0
8.0
Q2
TXB0104PWR
TSSOP
PW
14
2000
330.0
12.4
6.9
5.6
1.6
8.0
12.0
Q1
TXB0104RGYR
VQFN
RGY
14
3000
330.0
12.4
3.75
3.75
1.15
8.0
12.0
Q1
TXB0104RUTR
UQFN
RUT
12
3000
180.0
8.4
1.95
2.3
0.75
4.0
8.0
Q1
TXB0104YZTR
DSBGA
YZT
12
3000
180.0
8.4
1.49
1.99
0.75
4.0
8.0
Q2
TXB0104ZXUR
BGA MI
CROSTA
R JUNI
OR
ZXU
12
2500
330.0
8.4
2.3
2.8
1.0
4.0
8.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
25-Mar-2011
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TXB0104DR
SOIC
D
14
2500
346.0
346.0
33.0
TXB0104GXUR
BGA MICROSTAR
JUNIOR
GXU
12
2500
340.5
338.1
20.6
TXB0104PWR
TSSOP
PW
14
2000
346.0
346.0
29.0
TXB0104RGYR
VQFN
RGY
14
3000
346.0
346.0
29.0
TXB0104RUTR
UQFN
RUT
12
3000
202.0
201.0
28.0
TXB0104YZTR
DSBGA
YZT
12
3000
190.5
212.7
31.8
TXB0104ZXUR
BGA MICROSTAR
JUNIOR
ZXU
12
2500
340.5
338.1
20.6
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Communications and Telecom www.ti.com/communications
Amplifiers
amplifier.ti.com
Computers and Peripherals
www.ti.com/computers
Data Converters
dataconverter.ti.com
Consumer Electronics
www.ti.com/consumer-apps
DLP® Products
www.dlp.com
Energy and Lighting
www.ti.com/energy
DSP
dsp.ti.com
Industrial
www.ti.com/industrial
Clocks and Timers
www.ti.com/clocks
Medical
www.ti.com/medical
Interface
interface.ti.com
Security
www.ti.com/security
Logic
logic.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Power Mgmt
power.ti.com
Transportation and
Automotive
www.ti.com/automotive
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
Wireless
www.ti.com/wireless-apps
RF/IF and ZigBee® Solutions
www.ti.com/lprf
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated