CEL UPG2150T5L

PRELIMINARY DATA SHEET
GaAs INTEGRATED CIRCUIT
UPG2150T5L
GaAs MMIC SP3T SWITCH FOR BLUETOOTH & 802.11b/g
DESCRIPTION
The uPG2150T5L is a GaAs MMIC SP3T switch for Bluetooth & wireless LAN. The device can operate from
500MHz to 2.5GHz, having the low insertion loss and high isolation.
FEATURES
• Operating frequency
: f = 0.5 to 2.5 GHz
• Low insertion loss
: LINS = 0.5 dB TYP. @ f = 2.5GHz, ANT to RF1,RF2
• Handling power
: Pin (1 dB) = +31 dBm TYP. @ f = 2.5GHz, ANT to RF1,RF2
• Control voltage
: Vcont = +2.85 V/0 V
• High isolation
: ISL = 35dB TYP. @ f =2.5 GHz, ANT to RF3 (ON)
0.6dB TYP. @ f = 2.5 GHz, ANT to RF3
+25 dBm TYP. @ f = 2.5 GHz, ANT to RF3
18 dB T Y P. @ f = 2. 5 GHz , A N T to R F 1 , 2( O N)
• 12-pin plastic TSQFN package (2.0 × 2.0 × 0.37 mm)
APPLICATION
• Bluetooth & 802.11b/g
ORDERING INFORMATION
Part Number
uPG2150T5L-E2-A
Package
12-pin plastic TSQFN
Marking
2150
Supplying Form
• Embossed tape 8 mm wide
• Pin 10,11,12 face the perforation side of the tape
• Qty 3 kpcs/reel
Remark To order evaluation samples, contact your nearby sales office.
Part number for sample order: uPG2150T5L
Caution Observe precautions when handling because these devices are sensitive to electrostatic discharge.
The information in this document is subject to change without notice. Before using this document, please confirm that
this is the latest version.
Document No. 1st version
Date Published DEC. 2004 CP(K)
UPG2150T5L
PIN CONNECTIONS AND INTERNAL BLOCK DIAGRAM
<Top View>
Pin No.
Pin Name
1
ANT
2
GND
3
Vcont2
4
RF2
5
GND
6
RF3
7
Vcont3
8
GND
9
Vcont1
10
RF1
11
GND
12
GND
<Bottom View>
TRUTH TABLE
Vcont1
Vcont2
Vcont3
ANT-RF1
ANT-RF2
ANT-RF3
2.3 to 3.6 V
0 ± 0.2 V
0 ± 0.2 V
ON
OFF
OFF
0 ± 0.2 V
2.3 to 3.6 V
0 ± 0.2 V
OFF
ON
OFF
0 ± 0.2 V
0 ± 0.2 V
2.3 to 3.6 V
OFF
OFF
ON
ABSOLUTE MAXIMUM RATINGS (TA = +25°C, unless otherwise specified)
Parameter
Switch Control Voltage
Symbol
Vcont
Ratings
−6.0 to +6.0
Unit
Note 1
V
Input Power@ Ant to RF1,2
Pin
+34
dBm
Input Power@ Ant to RF3
Pin
+28
dBm
Operating Ambient Temperature
TA
−45 to +85
°C
Storage Temperature
Tstg
−55 to +150
°C
Notes 1. | Vcont1 − Vcont2 | ≤ 6.0 V
2. Mounted on double-sided copper-clad 50 × 50 × 1.6 mm epoxy glass PWB, TA = +85°C
2
PRELIMINARY DATA SHEET
UPG2150T5L
RECOMMENDED OPERATING RANGE (TA = +25°C)
Parameter
Symbol
MIN.
TYP.
MAX.
Unit
f
0.5
−
2.5
GHz
Switch Control Voltage (H)
Vcont (H)
2.3
2.85
3.6
V
Switch Control Voltage (L)
Vcont (L)
−0.2
0
0.2
V
Operating Frequency
ELECTRICAL CHARACTERISTICS (TA =+25°C, Vcont = 2.85V/0 V, ZO = 50 Ω, DC blocking capacitors
value: 56 pF, Each port, unless otherwise specified)
Parameter
Insertion Loss
Symbol
LINS
Pass
ANT to RF1,2
ANT to RF3
Isolation
ISL
ANT to RF3 OFF
@ANT to RF1,2 ON
Test Conditions
MIN.
TYP.
MAX.
Unit
f = 0.5 to 1.0GHz
−
0.40
0.55
dB
f = 1.0 to 2.0GHz
−
0.45
0.60
dB
f = 2.0 to 2.5GHz
−
0.50
0.65
dB
f = 0.5 to 1.0GHz
−
0.45
0.60
dB
f = 1.0 to 2.0GHz
−
0.55
0.70
dB
f = 2.0 to 2.5GHz
−
0.60
0.75
dB
f = 0.5 to 1.0GHz
29
32
−
dB
f = 1.0 to 2.0GHz
30
35
dB
f = 2.0 to 2.5GHz
30
35
dB
f = 0.5 to 1.0GHz
23
26
f = 1.0 to 2.0GHz
17
20
dB
f = 2.0 to 2.5GHz
15
18
dB
RF1 to RF3 OFF
@ANT-RF1ON
ANT to RF1 OFF
@ANT to RF2,3 ON
ANT to RF2 OFF
@ANT to RF1,3 ON
−
dB
Input Return Loss
RLin
ANT to RF1,2,3
f = 0.5 to 2.5GHz
15
20
−
dB
Output Return Loss
RLout
ANT to RF1,2,3
f = 0.5 to 2.5GHz
15
20
−
dB
Icont
ANT to RF1,2,3
RF Non
−
0.1
1.0
µA
Pin (1 dB)
ANT to RF1,2,
f = 1.0 GHz
Switch Control Current
Input Power at 1dB
Compression Point
f = 2.0 GHz
dBm
28
31
−
f = 2.5 GHz
ANT to RF3
dBm
f = 1.0 GHz
f = 2.0 GHz
20
25
−
−
50
−
f = 2.5 GHz
Switch Control Speed
tSW
ANT to RF1,2,3
-
PRELIMINARY DATA SHEET
ns
3
UPG2150T5L
EVALUATION CIRCUIT
C1 56 F
C2 1000pF
The application circuits and their parameters are for reference only and are not intended for use in actual design-ins.
4
PRELIMINARY DATA SHEET
UPG2150T5L
PACKAGE DIMENSIONS
PRELIMINARY DATA SHEET
5
UPG2150T5L
RECOMMENDED SOLDERING CONDITIONS
This product should be soldered and mounted under the following recommended conditions.
For soldering
methods and conditions other than those recommended below, contact your nearby sales office.
Soldering Method
Infrared Reflow
VPS
Wave Soldering
Soldering C o n d i t i o n s
Condition Symbol
Peak temperature (package surface temperature)
: 260°C or below
Time at peak temperature
: 10 seconds or less
Time at temperature of 220°C or higher
: 60 seconds or less
Preheating time at 120 to 180° C
: 120±30 seconds
Maximum number of reflow processes
: 3 times
Maximum chlorine content of rosin flux (% mass)
: 0.2%(Wt.) or below
Peak temperature (package surface temperature)
: 215°C or below
Time at temperature of 200°C or higher
: 25 to 40 seconds
Preheating time at 120 to 150° C
: 30 to 60 seconds
Maximum number of reflow processes
: 3 times
Maximum chlorine content of rosin flux (% mass)
: 0.2%(Wt.) or below
Peak temperature (molten solder temperature)
: 260°C or below
Time at peak temperature
: 10 seconds or less
IR260
VP215
WS260
Preheating temperature (package surface temperature) : 120°C or below
Partial Heating
Maximum number of flow processes
: 1 time
Maximum chlorine content of rosin flux (% mass)
: 0.2%(Wt.) or below
Peak temperature (pin temperature)
: 350°C or below
Soldering time (per side of device)
: 3 seconds or less
Maximum chlorine content of rosin flux (% mass)
: 0.2%(Wt.) or below
Caution Do not use different soldering methods together (except for partial heating).
6
PRELIMINARY DATA SHEET
HS350
4590 Patrick Henry Drive
Santa Clara, CA 95054-1817
Telephone: (408) 919-2500
Facsimile: (408) 988-0279
Subject: Compliance with EU Directives
CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant
with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous
Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive
2003/11/EC Restriction on Penta and Octa BDE.
CEL Pb-free products have the same base part number with a suffix added. The suffix –A indicates
that the device is Pb-free. The –AZ suffix is used to designate devices containing Pb which are
exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals.
All devices with these suffixes meet the requirements of the RoHS directive.
This status is based on CEL’s understanding of the EU Directives and knowledge of the materials that
go into its products as of the date of disclosure of this information.
Restricted Substance
per RoHS
Concentration Limit per RoHS
(values are not yet fixed)
Concentration contained
in CEL devices
-A
Not Detected
Lead (Pb)
< 1000 PPM
Mercury
< 1000 PPM
Not Detected
Cadmium
< 100 PPM
Not Detected
Hexavalent Chromium
< 1000 PPM
Not Detected
PBB
< 1000 PPM
Not Detected
PBDE
< 1000 PPM
Not Detected
-AZ
(*)
If you should have any additional questions regarding our devices and compliance to environmental
standards, please do not hesitate to contact your local representative.
Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance
content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information
provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better
integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate
information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL
suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for
release.
In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to
customer on an annual basis.
See CEL Terms and Conditions for additional clarification of warranties and liability.