GaAs INTEGRATED CIRCUIT µPG2163T5N SPDT SWITCH FOR 2.4 GHz AND 6 GHz DUAL-BAND WIRELESS LAN DESCRIPTION The µPG2163T5N is GaAs MMIC SPDT (Single Pole Double Throw) switch which was developed for 2.4 GHz and 6 GHz dual-band wireless LAN. This device can operate frequency from 2.4 GHz band and 6 GHz band, having the low insertion loss and high isolation. This device is housed in a 6-pin plastic TSON (Thin Small Out-line Non-leaded) package. And this package is able to high-density surface mounting. FEATURES • Operating frequency • Switch control voltage : f = 2.4 to 2.5 GHz and 4.9 to 6.0 GHz : Vcont (H) = 2.8 to 5.0 V (3.0 V TYP.) : Vcont (L) = −0.3 to 0.3 V (0 V TYP.) • Low insertion loss : Lins1 = 0.40 dB TYP. @ f = 2.4 to 2.5 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V : Lins2 = 0.50 dB TYP. @ f = 4.9 to 6.0 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V • High isolation : ISL1 = 38 dB TYP. @ f = 2.4 to 2.5 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V : ISL2 = 30 dB TYP. @ f = 4.9 to 6.0 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V • Handling power : Pin (1 dB) = +31.0 dBm TYP. @ f = 2.5 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V : Pin (1 dB) = +29.0 dBm TYP. @ f = 6.0 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V • High-density surface mounting : 6-pin plastic TSON package (1.5 × 1.5 × 0.37 mm) APPLICATIONS • Dual-band wireless LAN (IEEE802.11a + b/g) ORDERING INFORMATION Part Number Order Number µPG2163T5N-E2 µPG2163T5N-E2-A Package 6-pin plastic TSON (Pb-Free) Marking G4X Supplying Form • Embossed tape 8 mm wide • Pin 1, 6 face the perforation side of the tape • Qty 3 kpcs/reel Remark To order evaluation samples, contact your nearby sales office. Part number for sample order: µPG2163T5N Caution Observe precautions when handling because these devices are sensitive to electrostatic discharge. Document No. PG10626EJ01V0DS (1st edition) Date Published July 2006 NS CP(K) µPG2163T5N PIN CONNECTIONS AND INTERNAL BLOCK DIAGRAM (Top View) G4X 1 2 (Bottom View) (Top View) 3 6 1 6 6 1 5 2 5 5 2 4 4 3 3 4 Pin No. Pin Name 1 GND 2 Vcont2 3 OUT2 (RX) 4 OUT1 (TX) 5 Vcont1 6 IN (ANT) Remark Exposed pad : GND TRUTH TABLE Vcont1 Vcont2 IN (ANT)−OUT1 (TX) IN (ANT)−OUT2 (RX) High Low OFF ON Low High ON OFF ABSOLUTE MAXIMUM RATINGS (TA = +25°C, unless otherwise specified) Parameter Symbol Ratings Unit Vcont −6.0 to +6.0 V Input Power Pin +32 dBm Operating Ambient Temperature TA −45 to +85 °C Storage Temperature Tstg −55 to +135 °C Switch Control Voltage RECOMMENDED OPERATING RANGE (TA = +25°C, unless otherwise specified) Parameter Symbol MIN. TYP. MAX. Unit Switch Control Voltage (H) Vcont (H) 2.8 3.0 5.0 V Switch Control Voltage (L) Vcont (L) −0.3 0 0.3 V Operating Frequency 1 f1 2.4 − 2.5 GHz Operating Frequency 2 f2 4.9 − 6.0 GHz 2 Data Sheet PG10626EJ01V0DS µPG2163T5N ELECTRICAL CHARACTERISTICS (TA = +25°C, Vcont (H) = 3.0 V, Vcont otherwise specified) Parameter Symbol (L) = 0 V, Z0 = 50 Ω, DC blocking capacitors = 4 pF, unless Test Conditions MIN. TYP. MAX. Unit Insertion Loss 1 Lins1 f = 2.4 to 2.5 GHz − 0.40 0.60 dB Insertion Loss 2 Lins2 f = 4.9 to 6.0 GHz − 0.50 0.80 dB Isolation 1 ISL1 f = 2.4 to 2.5 GHz 35 38 − dB Isolation 2 ISL2 f = 4.9 to 6.0 GHz 27 30 − dB Input Return Loss 1 RLin1 f = 2.4 to 2.5 GHz − 15 − dB Input Return Loss 2 RLin2 f = 4.9 to 6.0 GHz − 15 − dB Output Return Loss 1 RLout1 f = 2.4 to 2.5 GHz − 15 − dB Output Return Loss 2 RLout2 f = 4.9 to 6.0 GHz − 15 − dB 1 dB Loss Compression Note Input Power 1 Pin (1 dB) 1 f = 2.4 to 2.5 GHz − +31.0 − dBm 1 dB Loss Compression Note Input Power 2 Pin (1 dB) 2 f = 4.9 to 6.0 GHz − +29.0 − dBm IIP3 − +55 − dBm Switch Control Current Icont − 0.1 1.0 µA Switch Control Speed tSW − 50 − ns Input 3rd Order Distortion Intercept Point 50% CTL to 90/10% Note Pin (1 dB) is measured the input power level when the insertion loss increases more 1 dB than that of linear range. Caution This device is used it is necessary to use DC blocking capacitors. Data Sheet PG10626EJ01V0DS 3 µPG2163T5N EVALUATION CIRCUIT 4 pF Vcont2 1 6 2 5 1 000 pF Vcont1 1 000 pF 4 3 OUT2 (RX) IN (ANT) OUT1 (TX) 4 pF 4 pF The application circuits and their parameters are for reference only and are not intended for use in actual design-ins. 4 Data Sheet PG10626EJ01V0DS µPG2163T5N MOUNTING PAD DIMENSIONS 6-PIN PLASTIC TSON (UNIT: mm) MOUNTING PAD 0.3 0.2 0.5 1.0 0.5 0.3 0.5 0.3 0.3 SOLDER PAD 0.475 0.15 0.5 0.55 0.5 0.25 0.35 0.475 0.25 Solder thickness : 0.08 mm Remark The mounting pad layouts in this document are for reference only. Data Sheet PG10626EJ01V0DS 5 µPG2163T5N PACKAGE DIMENSIONS 6-PIN PLASTIC TSON (UNIT: mm) (Bottom View) (Side View) 0.3±0.07 0.2+0.07 –0.05 1.5±0.1 0.5±0.06 1.5±0.1 1.2±0.1 (Top View) 0.37+0.03 –0.05 6 0.2±0.1 Data Sheet PG10626EJ01V0DS 0.7±0.1 µPG2163T5N RECOMMENDED SOLDERING CONDITIONS This product should be soldered and mounted under the following recommended conditions. For soldering methods and conditions other than those recommended below, contact your nearby sales office. Soldering Method Infrared Reflow Wave Soldering Soldering Conditions Condition Symbol Peak temperature (package surface temperature) : 260°C or below Time at peak temperature : 10 seconds or less Time at temperature of 220°C or higher : 60 seconds or less Preheating time at 120 to 180°C : 120±30 seconds Maximum number of reflow processes : 3 times Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below Peak temperature (molten solder temperature) : 260°C or below Time at peak temperature : 10 seconds or less IR260 WS260 Preheating temperature (package surface temperature) : 120°C or below Partial Heating Maximum number of flow processes : 1 time Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below Peak temperature (terminal temperature) : 350°C or below Soldering time (per side of device) : 3 seconds or less Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below HS350 Caution Do not use different soldering methods together (except for partial heating). Data Sheet PG10626EJ01V0DS 7 4590 Patrick Henry Drive Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279 Subject: Compliance with EU Directives CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. CEL Pb-free products have the same base part number with a suffix added. The suffix –A indicates that the device is Pb-free. The –AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL’s understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information. Restricted Substance per RoHS Concentration Limit per RoHS (values are not yet fixed) Concentration contained in CEL devices -A Not Detected Lead (Pb) < 1000 PPM Mercury < 1000 PPM Not Detected Cadmium < 100 PPM Not Detected Hexavalent Chromium < 1000 PPM Not Detected PBB < 1000 PPM Not Detected PBDE < 1000 PPM Not Detected -AZ (*) If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative. Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability.