TPS54326 www.ti.com SLVSA13A – OCTOBER 2009 – REVISED OCTOBER 2009 4.5V to 18V Input, 3-A Synchronous Step-Down SWIFTTM Converter with Light Load Efficiency Check for Samples: TPS54326 FEATURES 1 • 23 • • • • • • • • • • • • D-CAP2™ Mode Enables Fast Transient Response Low Output Ripple and Allows Ceramic Output Capacitor Wide VCC Input Voltage Range: 4.5 V to 18 V Wide VIN Input Voltage Range: 2 V to 18 V Output Voltage Range: 0.76 V to 5.5 V Highly Efficient Integrated FET’s Optimized for Lower Duty Cycle Applications - 120 mΩ (High Side) and 70 mΩ (Low Side) High Efficiency, less than 10 μA at Shutdown High Initial Bandgap Reference Accuracy Adjustable Soft Start Pre-Biased Soft Start 700-kHz Switching Frequency (fSW) Cycle-By-Cycle Overcurrent Limit Power Good Output APPLICATIONS • Wide Range of Applications for Low Voltage System – Digital TV Power Supply – High Definition Blu-ray Disc™ Players – Networking Home Terminal – Digital Set Top Box (STB) DESCRIPTION The TPS54326 is an adaptive on-time D-CAP2™ mode synchronous buck converter. The TPS54326 enables system designers to complete the suite of various end equipment’s power bus regulators with a cost effective, low component count, low standby current solution. The main control loop for the TPS54326 uses the D-CAP2™ mode control which provides a fast transient response with no external components. The adoptive on-time control supports seamless operation between PWM mode at heavy load condition and reduced frequency operation at light load for high efficiency. The TPS54326 also has a proprietary circuit that enables the device to adapt to both low equivalent series resistance (ESR) output capacitors, such as POSCAP or SP-CAP, and ultra-low ESR ceramic capacitors. The device operates from 4.5-V to 18-V VCC input , and from 2-V to 18-V VIN input power supply voltage. The output voltage can be programmed between 0.76 V and 5.5 V. The device also features an adjustable slow start time and a power good function. The TPS54326 is available in the 14 pin HTSSOP package, and designed to operate from –40°C to 85°C. VOUT (50 mV/div) IOUT (1 A/div) 100 ms/div 1 2 3 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. D-CAP2, PowerPAD are trademarks of Texas Instruments. Blu-ray Disc is a trademark of Blu-ray Disc Association. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2009, Texas Instruments Incorporated TPS54326 SLVSA13A – OCTOBER 2009 – REVISED OCTOBER 2009 www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. ORDERING INFORMATION (1) TA PACKAGE (2) (3) TRANSPORT MEDIA, QUANTITY ORDERABLE PART NUMBER PowerPAD™ (HTSSOP) – PWP (14 Pins) –45°C to 85°C (1) (2) (3) TPS54326PWP Tube TPS54326PWPR Tape and Reel, 3000 For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI web site at www.ti.com. Package drawings, thermal data, and symbolization are available at www.ti.com/packaging. All package options have Cu NIPDAU lead/ball finish. ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range (unless otherwise noted) VI Input voltage range (1) VALUE UNIT VIN, VCC, EN –0.3 to 20 V VBST –0.3 to 26 V VBST (vs SW1, SW2) –0.3 to 6.5 V VFB, VO, SS, PG –0.3 to 6.5 V –2 to 20 V SW1, SW2 SW1, SW2 (10 ns transient) VO Output voltage range Vdiff Voltage from GND to POWERPAD –3 to 20 V VREG5 –0.3 to 6.5 V PGND1, PGND2 –0.3 to 0.3 V Human Body Model (HBM) ESD rating Electrostatic discharge V 2 kV 500 V TJ Operating junction temperature –40 to 150 °C Tstg Storage temperature –55 to 150 °C (1) Charged Device Model (CDM) –0.2 to 0.2 Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. DISSIPATION RATINGS (1) (2 oz. trace and copper pad with solder) (1) PACKAGE θJA TA = 25°C POWER RATING TA = 85°C POWER RATING PWP 44.5°C/W 2.25 W 0.9 W Rating based on JEDEC high thermal conductivity (High K) board with 2 x 2 arrays of thermal vias. See Texas Instruments application report (SLMA002) regarding thermal characteristic of the PowerPAD™ package. 2 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPS54326 TPS54326 www.ti.com SLVSA13A – OCTOBER 2009 – REVISED OCTOBER 2009 RECOMMENDED OPERATING CONDITIONS over operating free-air temperature range (unless otherwise noted) VCC Supply input voltage range VIN Power input voltage range VI Input voltage range MIN MAX 4.5 18 V V 2 18 VBST –0.1 24 VBST (vs SW1, SW2) –0.1 5.7 SS, PG –0.1 5.7 EN –0.1 18 VO, VFB –0.1 5.5 SW1, SW2 –1.8 18 SW1, SW2 (10 ns transient) UNIT V –3 18 PGND1, PGND2 –0.1 0.1 VREG5 –0.1 5.7 V VO Output voltage range TA Operating free-air temperature –40 85 °C TJ Operating junction temperature –40 125 °C TYP MAX UNIT ELECTRICAL CHARACTERISTICS over operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS MIN SUPPLY CURRENT IVCC Operating - non-switching supply current VCC current, TA = 25°C, EN = 5 V, VFB = 0.8 V 850 1300 μA IVCCSDN Shutdown supply current VCC current, TA = 25°C, EN = 0 V 1.8 10 μA LOGIC THRESHOLD VENH EN high-level input voltage EN VENL EN low-level input voltage EN 2 V 0.4 V VFB VOLTAGE AND DISCHARGE RESISTANCE VFB Voltage light load mode TA = 25°C, VO = 1.05 V, IO = 10 mA VFB Threshold voltage, continuous mode TA = 0°C to 85°C, VO = 1.05 V (1) TA = 25°C, VO = 1.05 V 771 757 TA = -40°C to 85°C, VO = 1.05 V (1) IVFB Input current VFB = 0.8 V, TA = 25°C RDischg VO discharge resistance EN = 0 V, VO = 0.5 V, TA = 25°C 765 mV 773 753 777 751 779 mV 0 ±0.1 μA 50 100 Ω 5.5 5.7 V 20 mV 100 mV VREG5 OUTPUT VVREG5 Output voltage TA = 25°C, 6 V < VCC < 18 V, 0 < IVREG5 < 5 mA VLN5 Line regulation 6 V < VCC < 18 V, IVREG5 = 5 mA VLD5 Load regulation 0 mA < IVREG5 < 5 mA IVREG5 Output current VCC = 6 V, VREG5 = 4 V, TA = 25°C RDS(on)h High side switch resistance 25°C, VBST - SW1, SW2 = 5.5 V RDS(on)l Low side switch resistance 25°C 5.3 70 mA 120 mΩ 70 mΩ MOSFET CURRENT LIMIT Iocl Current limit L out = 1.5µH (1) 3.5 4.1 5.5 A THERMAL SHUTDOWN TSDN Thermal shutdown threshold Shutdown temperature Hysteresis (1) (1) 150 25 °C ON-TIME TIMER CONTROL (1) Specified by Design (not production tested). 3 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPS54326 TPS54326 SLVSA13A – OCTOBER 2009 – REVISED OCTOBER 2009 www.ti.com ELECTRICAL CHARACTERISTICS (continued) over operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX tON On time VIN = 12 V, VO = 1.05 V 145 tOFF(MIN) Minimum off time TA = 25°C, VFB = 0.7 V 260 310 2.6 UNIT ns ns SOFT START ISSC SS charge current VSS = 0 V 1.4 2 ISSD SS discharge current VSS = 0.5 V 0.1 0.2 VFB rising (good) 85 90 μA mA POWER GOOD VTHPG Threshold IPG Sink current VFB falling (fault) 95 85 PG = 0.5 V 2.5 5 115 120 % mA OUTPUT UNDERVOLTAGE AND OVERVOLTAGE PROTECTION VOVP Output OVP trip threshold tOVPDEL Output OVP prop delay VUVP Output UVP trip threshold tUVPDEL Output UVP delay tUVPEN Output UVP enable delay OVP detect 125 UVP detect 65 Hysteresis 70 75 10 0.25 Relative to soft-start time % μs 5 % ms x 1.7 UVLO UVLO Threshold Wake up VREG5 voltage 3.55 3.8 4.05 Hysteresis VREG5 voltage 0.23 0.35 0.47 V DEVICE INFORMATION PWP PACKAGE (TOP VIEW) PWP PACKAGE (TOP VIEW) VO 1 14 VCC VFB 2 13 VIN VREG5 3 12 VBST SS 4 11 SW2 GND 5 10 SW1 PG 6 9 PGND2 EN 7 8 PGND1 POWERPAD PIN FUNCTIONS PIN NAME NO. DESCRIPTION VO 1 Connect to output of converter. This pin is used for On-Time Adjustment. VFB 2 Converter feedback input. Connect with feedback resistor divider. VREG5 3 5.5 V power supply output. A capacitor (typical 1μF) should be connected to GND. SS 4 Soft-start control. A external capacitor should be connected to GND. 4 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPS54326 TPS54326 www.ti.com SLVSA13A – OCTOBER 2009 – REVISED OCTOBER 2009 PIN FUNCTIONS (continued) PIN NAME DESCRIPTION NO. GND 5 Signal ground pin PG 6 Open drain power good output EN 7 Enable control input PGND1, PGND2 Ground returns for low-side MOSFET. Also serve as inputs of current comparators. Connect PGND and GND strongly together near the IC. 8, 9 SW1, SW2 Switch node connection between high-side NFET and low-side NFET. Also serve as inputs to current comparators. 10, 11 VBST 12 Supply input for high-side NFET gate driver (boost terminal). Connect capacitor from this pin to respective SW1, SW2 terminals. An internal PN diode is connected between VREG5 to VBST pin. VIN 13 Power input and connected to high side NFET drain VCC 14 Supply input for 5 V internal linear regulator for the control circuitry PowerPAD™ Back side Thermal pad of the package. Must be soldered to achieve appropriate dissipation. Should be connected to PGND. Functional Block Diagram -20% UV 14 VCC VIN OV 1 13 +20% VO VIN VREG5 12 VBST Ref SS SW 11 10 2 VFB VREG5 SGND VREG5 Ceramic Capacitor 3 SS 4 GND SW PGND SGND PG PGND PGND SS 5 9 8 SW ZC Softstart PGND VO Ref 6 VCC -10% UV VREG 5 EN 7 UVLO EN Logic OV UVLO Protection Logic TSD REF Ref 5 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPS54326 TPS54326 SLVSA13A – OCTOBER 2009 – REVISED OCTOBER 2009 www.ti.com OVERVIEW The TPS54326 is a 3-A synchronous step-down (buck) converter with two integrated N-channel MOSFETs. It operates using D-CAP2™ mode control. The fast transient response of D-CAP2™ control reduces the output capacitance required to meet a specific level of performance. Proprietary internal circuitry allows the use of low ESR output capacitors including ceramic and special polymer types. DETAILED DESCRIPTION PWM Operation The main control loop of the TPS54326 is an adaptive on-time pulse width modulation (PWM) controller that supports a proprietary D-CAP2™ mode control. D-CAP2™ mode control combines constant on-time control with an internal compensation circuit for pseudo-fixed frequency and low external component count configuration with both low ESR and ceramic output capacitors. It is stable even with virtually no ripple at the output. At the beginning of each cycle, the high-side MOSFET is turned on. This MOSFET is turned off after internal one shot timer expires. This one shot timer is set by the converter input voltage ,VIN, and the output voltage ,VO, to maintain a pseudo-fixed frequency over the input voltage range, hence it is called adaptive on-time control. The one-shot timer is reset and the high-side MOSFET is turned on again when the feedback voltage falls below the reference voltage. An internal ramp is added to the reference voltage to simulate output ripple, eliminating the need for ESR induced output ripple from D-CAP2™ mode control. PWM Frequency and Adaptive On-Time Control TPS54326 uses an adaptive on-time control scheme and does not have a dedicated on board oscillator. The TPS54326 runs with a pseudo-constant frequency of 700 kHz by using the input voltage and output voltage to set the on-time one-shot timer. The on-time is inversely proportional to the input voltage and proportional to the output voltage. The actual frequency may vary from 700 kHz depending on the off time, which is ended when the fed back portion of the output voltage falls to the VFBthreshold voltage. Light Load Mode Control The TPS54326 is designed with Auto-Skip mode to increase light load efficiency. As the output current decreases from heavy load condition, the inductor current is also reduced and eventually comes to point that its rippled valley touches zero level, which is the boundary between continuous conduction and discontinuous conduction modes. The rectifying MOSFET is turned off when its zero inductor current is detected. As the load current further decreases the converter run into discontinuous conduction mode. The on-time is kept almost the same as is was in the continuous conduction mode so that it takes longer time to discharge the output capacitor with smaller load current to the level of the reference voltage. The transition point to the light load operation I OUT(LL) current can be calculated in Equation 1. 1 (VIN - VOUT) · VOUT IOUT(LL) = - = 2 · L · fws VIN (1) Soft Start and Pre-Biased Soft Start The soft start function is adjustable. When the EN pin becomes high, 2-μA current begins charging the capacitor which is connected from the SS pin to GND. Smooth control of the output voltage is maintained during start up. The equation for the slow start time is shown in Equation 2. VFB voltage is 0.765 V and SS pin source current is 2 μA. C6(nF) • Vref C6(nF) • 0.765 Tss(ms) = − = − Iss(µA) 2 (2) A unique circuit to prevent current from being pulled from the output during startup if the output is pre-biased. When the soft-start commands a voltage higher than the pre-bias level (internal soft start becomes greater than feedback voltage VFB), the controller slowly activates synchronous rectification by starting the first low side FET gate driver pulses with a narrow on-time. It then increments that on-time on a cycle-by-cycle basis until it coincides with the time dictated by (1-D), where D is the duty cycle of the converter. This scheme prevents the initial sinking of the pre-bias output, and ensure that the out voltage (VO) starts and ramps up smoothly into regulation and the control loop is given time to transition from pre-biased start-up to normal mode operation. 6 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPS54326 TPS54326 www.ti.com SLVSA13A – OCTOBER 2009 – REVISED OCTOBER 2009 Power Good The power good function is activated after soft start has finished. The power good function becomes active after 1.7 times soft-start time. When the output voltage is within -10% of the target value, internal comparators detect power good state and the power good signal becomes high. The power good output, PG, is an open drain output. If the feedback voltage goes under 15% of the target value, the power good signal becomes low after a 10 μs internal delay. Output Discharge Control TPS54326 discharges the output when EN is low, or the controller is turned off by the protection functions (OVP, UVP, UVLO and thermal shutdown). The output is discharged by an internal 50-Ω MOSFET which is connected from VO to PGND. The internal low-side MOSFET is not turned on during the output discharge operation to avoid the possibility of causing negative voltage at the output. Current Protection Output current is limited by cycle-by-cycle overcurrent limiting control. The inductor current is monitored during the OFF state and the controller keeps the OFF state when the inductor current is larger than the over current trip level. To provide accuracy and a cost effective solution, the device supports temperature compensated internal MOSFET RDS(on) sensing. The inductor current is monitored by the voltage between PGND pin and SW1/SW2 pin. In an overcurrent condition, the current to the load exceeds the current to the output capacitor; thus, the output voltage tends to fall off. Eventually the output voltage will fall below the undervoltage protection threshold and the device will shutdown. Over/Undervoltage Protection The TPS54326 detects over and undervoltage conditions by monitoring the feedback voltage (VFB). This function is enabled after approximately 1.7 times the soft-start time.When the feedback voltage becomes higher than 120% of the target voltage, the OVP comparator output goes high and the circuit latches the high-side MOSFET driver turns off and the low-side MOSFET turns on. When the feedback voltage becomes lower than 70% of the target voltage, the UVP comparator output goes high and an internal UVP delay counter begins. After 250 μs, the device latches off both internal top and bottom MOSFET. UVLO Protection Undervoltage lock out protection (UVLO) monitors the voltage of the VREG5 pin. When the VREG5 voltage is lower than UVLO threshold voltage, the TPS54326 is shut off. This is protection is non-latching. Thermal Shutdown Thermal protection is self-activating. If the junction temperature exceeds the threshold value (typically 150°C), the TPS54326 shuts off. This protection is non-latching. 7 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPS54326 TPS54326 SLVSA13A – OCTOBER 2009 – REVISED OCTOBER 2009 www.ti.com TYPICAL CHARACTERISTICS 1200 8 1000 Shutdown Current - mA Supply Current - mA 6 800 600 400 4 2 200 0 -50 0 50 100 TJ - Junction Temperature - °C 0 -50 150 Figure 1. VCC SUPPLY CURRENT vs. JUNCTION TEMPERATURE 50 100 TJ - Junction Temperature - °C 150 Figure 2. VCC SHUTDOWN CURRENT vs. JUNCTION TEMPERATURE 1.1 1.1 1.075 1.05 VI = 12 V IO = 10 mA 1.075 VI = 18 V VO - Output Voltage - V VO - Output Voltage - V 0 VI = 5 V 1.05 IO = 1 mA 1.025 1.025 1 1 0 0.5 1 1.5 2 IO - Output Current - A 2.5 Figure 3. 1.05-V OUTPUT VOLTAGE vs. OUTPUT CURRENT 3 0 5 10 VI - Input Voltage - V 15 20 Figure 4. 1.05-V OUTPUT VOLTAGE vs. INPUT VOLTAGE 8 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPS54326 TPS54326 www.ti.com SLVSA13A – OCTOBER 2009 – REVISED OCTOBER 2009 TYPICAL CHARACTERISTICS (continued) VOUT (50 mV/div) EN (10 V/div) VOUT (0.5 V/div) IOUT (1 A/div) PG (5 V/div) 100 ms/div 400 ms/div Figure 5. 1.05-V, 0-A TO 3-A LOAD TRANSIERESPONSE Figure 6. START-UP WAVE FORM 100 100 VO = 3.3 V VO = 3.3 V 20 80 VO = 1.8 V VO = 2.5 V Efficiency - % Efficiency - % 80 60 VO = 1.8 V 60 VO = 2.5 40 40 20 20 0 0 0.5 1 1.5 2 IO - Output Current - A 2.5 Figure 7. EFFICIENCY vs. OUTPUT CURRENT (VIN = 12 V) 3 0 0.001 0.01 IO - Output Current - A 0.1 Figure 8. LIGHT LOAD EFFICIENCY vs. OUTPUT CURRENT 9 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPS54326 TPS54326 SLVSA13A – OCTOBER 2009 – REVISED OCTOBER 2009 www.ti.com TYPICAL CHARACTERISTICS (continued) 900 900 800 VO = 1.8 V fsw - Switching Frequency - kHz fsw - Switching Frequency - kHz 700 800 600 VO = 1.8 V VO = 2.5 V 500 700 400 300 VO = 3.3 V 600 200 100 500 0 5 10 VI - Input Voltage - V 15 Figure 9. SWITCHING FREQUENCY vs INPUT VOLTAGE 20 0 0.001 0.01 IO - Output Current - A 0.1 Figure 10. SWITCHING FREQUENCY vs OUTPUT CURRENT VIN (50 mV/div) VO (10 mV/div) SW (5 V/div) SW (5 V/div) 400 ns/div 400 ns/div Figure 11. VOLTAGE RIPPLE At OUTPUT Figure 12. VOLTAGE RIPPLE At INPUT 10 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPS54326 TPS54326 www.ti.com SLVSA13A – OCTOBER 2009 – REVISED OCTOBER 2009 DESIGN GUIDE Step By Step Design Procedure This example details the design of a switching regulator design using ceramic output capacitors. This design is available as the HPA540 evaluation module (EVM). A few parameters must be known in order to start the design process. These parameters are typically determined on the system level. For this example, start with the following known parameters: • Input voltage range = 4.5 - 18 V • Output voltage = 1.05 V • Output current = 3 A • Output voltage ripple = 3% of output voltage, 31.5 mV Figure 13 shows the schematic diagram for this design example. Figure 13. Schematic Output Inductor Selection The inductance value is selected to provide approximately 30% peak-to-peak ripple current at maximum load. Larger ripple current increases output ripple voltage, improves S/N ratio and contributes to stable operation. Smaller ripple currents result in lower output voltage ripple. When using low ESR output capacitors output ripple voltage is usually low, so larger ripple currents are acceptable. The coefficient Kind represents the percentage of ripple current. The value of Kind must not be greater than 0.4. Use 0.3 when using low ESR output capacitors. Equation 3 can be used to calculate L1. Use 700 kHz for fSW. Make sure the chosen inductor is rated for the peak current of Equation 5 and the RMS current of Equation 6. 11 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPS54326 TPS54326 SLVSA13A – OCTOBER 2009 – REVISED OCTOBER 2009 www.ti.com VOUT VIN (max) - VOUT •− LO = − VIN (max) IOUT • fSW • Kind (3) VOUT VIN (max) - VOUT • Ilp - p = V L •f (4) IN (max) O SW Ilp - p Ilpeak = IO + 2 − 1 Ilp - p2 ILo(RMS) = IO2 + − 12 (5) √ (6) For this design example, use KIND = 0.3 and the inductor value is calculated to be 1.56 μH. For this design, a nearest standard value was chosen: 1.5 μH. For 1.5 μH, the calculated peak current is 3.47 A and the calculated RMS current is 3.012 A. The inductor used is a TDK SPM6530-1R5M100 with a peak current rating of 11.5 A and an RMS current rating of 11 A. Output Capacitor Selection The capacitor value and ESR determines the amount of output voltage ripple. Recommended to use ceramic output capacitor. Using Equation 7 to Equation 9, an initial estimate for the capacitor value, ESR, and RMS current can be calculated. If the load transients are significant consider using the load step, instead of ripple current to calculate the maximum ESR. 1 •− 1 CO > − 8 • fSW VO(ripple) - RESR − I(ripple) (7) VO(ripple) RESR < − Il(ripple) (8) VOUT • (VIN - VOUT) ICO(RMS) =− − √12 • VIN • LO • fSW (9) ( ) For this design, the minimum required capacitance is 8.45 µF and maximum ESR is 33 mohm. Two TDK C3216JB0J226M 22 µF output capacitors are used. The maximum ESR is 12 mohm each. The calaculated RMS current is .271 A and each output capacitor is rated for 2 A. Input Capacitor Selection The device requires an input decoupling capacitor and a bulk capacitor is needed depending on the application. A ceramic capacitor over 10 μF is recommended for the decoupling capacitor. The capacitor voltage rating needs to be greater than the maximum input voltage. In case of separate VCC and VIN, then a ceramic capacitor over 10 μF is recommended for the VIN and also placing ceramic capacitor over 0.1 μF for the VCC is recommended. Bootstrap Capacitor Selection A 0.1-μF ceramic capacitor must be connected between the VBST to SW pin for proper operation. It is recommended to use a ceramic capacitor. VREG5 Capacitor Selection A 1-μF ceramic capacitor must be connected between the VREG5 to GND pin for proper operation. It is recommended to use a ceramic capacitor. Output Voltage Resistors Selection The output voltage is set with a resistor divider from the output node to the VFB pin. It is recommended to use 1% tolerance or better divider resistors. Start by using Equation 10 and Equation 11 to calculate VOUT. To improve efficiency at light loads consider using larger value resistors, too high of resistance will be more susceptible to noise and voltage errors from the VFB input current will be more noticeable. 12 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPS54326 TPS54326 www.ti.com SLVSA13A – OCTOBER 2009 – REVISED OCTOBER 2009 For output voltage from 0.76 V to 2.5 V: ( R1 VOUT = 0.765 • 1 + − R2 ) (10) For output voltage over 2.5 V: ( R1 VOUT = (0.763 + 0.0017 • VOUT) • 1 + − R2 ) (11) The required outut voltage for this design is 1.05 V, so the equation of (add cross reference) is used to calculate the value of R1. With R2 = 22.1 kohm, R1 is 8.25 kohm. THERMAL INFORMATION This PowerPAD™ package incorporates an exposed thermal pad that is designed to be connected to an external heatsink. The thermal pad must be soldered directly to the printed board (PCB). After soldering, the PCB can be used as a heatsink. In addition, through the use of thermal vias, the thermal pad can be attached directly to the appropriate copper plane shown in the electrical schematic for the device, or alternatively, can be attached to a special heatsink structure designed into the PCB. This design optimizes the heat transfer from the integrated circuit (IC). For additional information on the PowerPAD™ package and how to use the advantage of its heat dissipating abilities, refer to Technical Breif, PowerPAD™ Thermally Enhanced Package, Texas Instruments Literature No. SLMA002 and Application Brief, PowerPAD™ Made Easy, Texas Instruments Literature No. SLMA004. The exposed thermal pad dimensions for this package are shown in the following illustration. 8 14 Thermal Pad 2.46 ° 7 1 2.31 Figure 14. Thermal Pad Dimensions 13 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPS54326 TPS54326 SLVSA13A – OCTOBER 2009 – REVISED OCTOBER 2009 www.ti.com LAYOUT CONSIDERATIONS 1. Keep the input switching current loop as small as possible. 2. Keep the SW node as physically small and short as possible to minimize parasitic capacitance and inductance and to minimize radiated emissions. Kelvin connections should be brought from the output to the feedback pin of the device. 3. Keep analog and non-switching components away from switching components. 4. Make a single point connection from the signal ground to power ground. 5. Do not allow switching current to flow under the device. 6. Keep the pattern lines for VIN and PGND broad. 7. Exposed pad of device must be connected to PGND with solder. 8. VREG5 capacitor should be placed near the device, and connected PGND. 9. Output capacitor should be connected to a broad pattern of the PGND. 10. Voltage feedback loop should be as short as possible, and preferably with ground shield. 11. Lower resistor of the voltage divider which is connected to the VFB pin should be tied to SGND. 12. Providing sufficient via is preferable for VIN, SW and PGND connection. 13. PCB pattern for VIN, SW, and PGND should be as broad as possible. 14. If VIN and VCC is shorted, VIN and VCC patterns need to be connected with broad pattern lines. 15. VIN Capacitor should be placed as near as possible to the device. Additional Thermal Vias FEEDBACK RESISTORS BIAS CAP Connection to POWER GROUND on internal or bottom layer SLOW START CAP ANALOG GROUND TRACE To Enable Control VCC INPUT BYPASS CAPACITOR VCC VOUT VCC VFB VIN VREG5 VBST SS SW1 GND SW2 PG EN VIN VIN INPUT BYPASS CAPACITOR BOOST CAPACITOR PGND1 EXPOSED POWERPAD AREA OUTPUT INDUCTOR PGND2 VOUT OUTPUT FILTER CAPACITOR Additional Thermal Vias POWER GROUND VIA to Ground Plane Etch on Bottom Layer or Under Component Figure 15. TPS54326 Layout 14 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPS54326 TPS54326 www.ti.com SLVSA13A – OCTOBER 2009 – REVISED OCTOBER 2009 REVISION HISTORY Changes from Original (October 2009) to Revision A • Page Changed the data sheet From: Product Preview To: Production Data ................................................................................ 1 15 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPS54326 PACKAGE OPTION ADDENDUM www.ti.com 2-Nov-2009 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty TPS54326PWP ACTIVE HTSSOP PWP 14 TPS54326PWPR ACTIVE HTSSOP PWP 14 90 Lead/Ball Finish MSL Peak Temp (3) Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 29-Oct-2009 TAPE AND REEL INFORMATION *All dimensions are nominal Device TPS54326PWPR Package Package Pins Type Drawing SPQ HTSSOP 2000 PWP 14 Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 330.0 12.4 Pack Materials-Page 1 7.0 B0 (mm) K0 (mm) P1 (mm) 5.6 1.6 8.0 W Pin1 (mm) Quadrant 12.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 29-Oct-2009 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPS54326PWPR HTSSOP PWP 14 2000 346.0 346.0 29.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DLP® Products DSP Clocks and Timers Interface Logic Power Mgmt Microcontrollers RFID RF/IF and ZigBee® Solutions amplifier.ti.com dataconverter.ti.com www.dlp.com dsp.ti.com www.ti.com/clocks interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lprf Applications Audio Automotive Broadband Digital Control Medical Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/medical www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2009, Texas Instruments Incorporated