GR1A THRU GR1M SURFACE MOUNT FAST SWITCHING RECTIFIER Reverse Voltage - 50 to 1000 Volts Forward Current - 1.0 Ampere Features Plastic package has Underwriters Laboratory Flammability Classification 94V-0 For surface mounted applications in order to optimize board space Low profile package Built-in strain relief, ideal for automated placement Fast switching for high efficiency Glass passivated chip junction High temperature soldering: 250 /10 seconds at terminals D IM E N S IO N S Mechanical Data in c h e s D IM A Case: SMA molded plastic over passivated chip Terminals: Solder plated, solderable per MIL-STD-750, method 2026 Polarity: Color band denotes cathode end Weight: 0.004 ounce, 0.118 gram m m M in . M a x . M in . M a x . 0 .2 1 6 0 .2 2 6 5 .4 8 5 .7 4 B 0 .1 7 6 0 .1 8 2 4 .4 8 4 .6 3 C 0 .0 9 4 0 .1 0 0 2 .4 0 2 .5 5 D 0 .1 7 0 0 .1 7 6 4 .3 3 4 .4 8 E 0 .0 3 9 0 .0 5 5 1 .0 0 1 .4 0 F 0 .0 8 0 0 .0 8 1 2 .0 3 2 .0 7 G 0 .0 6 8 0 .0 8 3 1 .7 2 2 .1 0 H 0 .1 1 2 0 .1 1 8 2 .8 5 3 .0 0 J 0 .0 5 7 - 1 .4 4 - K - 0 .0 1 8 - 0 .4 5 L 0 .0 1 6 - 0 .4 0 N o te - M 0 .1 0 9 0 .1 1 5 2 .7 7 2 .9 3 N 0 .1 0 5 0 .1 0 7 2 .6 7 2 .7 3 P 0 .0 7 8 0 .0 8 1 2 .0 0 2 .0 5 Maximum Ratings and Electrical Characteristics Ratings at 25 ambient temperature unless otherwise specified. Symbols GR1A GR1B GR1D GR1G GR1J GR1K GR1M Units Maximum repetitive peak reverse voltage VRRM 50 100 200 400 600 800 1000 Volts Maximum RMS voltage VRMS 35 70 140 280 420 560 700 Volts Maximum DC blocking voltage VDC 50 100 200 400 600 800 1000 Volts Maximum average forward rectified current at TL=90 I(AV) 1.0 Amp Peak forward surge current 8.3mS single half sine-wave superimposed on rated load (MIL-STD-750D 4066 method) TL=90 IFSM 30.0 Amps Maximum instantaneous forward voltage at 1.0A VF 1.30 Volts IR 5.0 50.0 A Maximum DC reverse current at rated DC blocking voltage TA=25 TA=125 Maximum reverse recovery time (Note 1) Trr Typical junction capacitance (Note 2) CJ Maximum thermal resistance (Note 3) Operating junction and storage temperature range R R 150 250 10.0 JL TJ, TSTG -55 to +150 Notes: (1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0MHz and applied reverse voltage of 4.0 volts (3) Thermal resistance from junction to ambient and from junction to lead mounted on P.C.B. with 0.2x0.2 (5.0x5.0mm) copper pad areas 1 nS 7.0 105.0 32.0 JA 500 F /W RATINGS AND CHARACTERISTIC CURVES 2