HD74HC4538 Dual Precision Retriggerable/Resettable Monostable Multivibrators Description Each multivibrator features both a negative, A, and a positive, B, transition triggered input, either of which can be used as an inhibit input. Also included is a clear input that when taken low resets the one short. The HD74HC4538 is retriggerable. That is, it may be triggered repeatedly while their outputs are generating a pulse and the pulse will be extended. Pulse width stability over a wide range of temperature. The output pulse equation is simply: tw = 0.7 (R) (C). Features • • • • • High Speed Operation: tpd (A or B to Y) = 22 ns typ (CL = 50 pF) High Output Current: Fanout of 10 LSTTL Loads Wide Operating Voltage: VCC = 2 to 6 V Low Input Current: 1 µA max Low Quiescent Supply Current Function Table Inputs Outputs CD A B Q Q L X X L H H L H H H H H X : Not triggered L Irrelevant Not triggered HD74HC4538 Pin Arrangement T1A 1 16 VCC T2A 2 T1 T2 T1 15 T1B CDA 3 CD T2 14 T2B AA 4 A CD 13 CDB BA 5 B A 12 AB QA 6 Q B 11 BB QA 7 Q Q 10 QB GND 8 Q 9 (Top view) 2 QB HD74HC4538 Block Diagram CX RX VCC T1A T2A QA AA BA QA CDA CX RX VCC T1B T2B QB AB BB QB CDB RX and CX are external components 3 HD74HC4538 Absolute Maximum Ratings Item Symbol Rating Unit Supply voltage range VCC –0.5 to +7.0 V Input voltage Vin –0.5 to VCC + 0.5 V Output voltage Vout –0.5 to VCC + 0.5 V DC input diode current I IK ±20 mA DC input diode current pin 2, 14 I IK ±30 mA DC output diode current I OK ±20 mA DC current drain per pin Iout ±25 mA DC current drain per VCC, GND I CC, I GND ±50 mA Power dissipation per package PT 500 mW Storage temperature Tstg –65 to +150 °C 4 HD74HC4538 DC Characteristics Ta = –40 to +85°C Ta = 25°C Item Symbol VCC (V) Min Typ Max Min Max Unit Input voltage VIH 2.0 1.5 — — 1.5 — V 4.5 3.15 — — 3.15 — 6.0 4.2 — — 4.2 — 2.0 — — 0.5 — 0.5 4.5 — — 1.35 — 1.35 6.0 — — 1.8 — 1.8 2.0 1.9 2.0 — 1.9 — 4.5 4.4 4.5 — 4.4 — 6.0 5.9 6.0 — 5.9 — 4.5 4.18 — — 4.13 — I OH = –4 mA 6.0 5.68 — — 5.63 — I OH = –5.2 mA 2.0 — 0.0 0.1 — 0.1 4.5 — 0.0 0.1 — 0.1 6.0 — 0.0 0.1 — 0.1 4.5 — — 0.26 — 0.33 I OL = 4 mA 6.0 — — 0.26 — 0.33 I OL = 5.2 mA VIL Output voltage VOH VOL Test Conditions V V V Vin = VIH or VIL I OH = –20 µA Vin = VIH or VIL I OL = 20 µA Input current Iin 6.0 — — ±0.1 — ±1.0 µA Vin = VCC or GND Quiescent supply current (standby state) I CC 6.0 — — 130 — 220 µA Vin = VCC or GND, QA = QB = GND, Iout = 0 µA Current drain (active state) I CC 6.0 — — 130 — 220 µA Vin = VCC or GND, QA = QB = VCC Pin 2, 14 = 0.5 VCC 5 HD74HC4538 AC Characteristics (CL = 50 pF, Input tr = tf = 6 ns) Ta = –40 to +85°C Ta = 25°C VCC (V) Min Typ Max Min Max Unit Test Conditions Propagation delay t PLH 2.0 — — 235 — 295 ns A or B to Q time 4.5 — 22 47 — 59 6.0 — — 40 — 50 2.0 — — 260 — 325 ns A or B to Q 4.5 — 23 52 — 65 6.0 — — 44 — 55 2.0 — — 235 — 295 ns CD to Q 4.5 — 17 47 — 59 6.0 — — 40 — 50 2.0 — — 235 — 295 ns CD to Q 4.5 — — 47 — 59 6.0 — — 40 — 50 2.0 80 — — 100 — ns A, B, C D 4.5 16 — — 20 — 6.0 14 — — 17 — 3.0 — 150 — — — ns RX = 1 kΩ, CX = 12 pF 5.0 — 100 — — — 3.0 — — — — — µs RX = 10 kΩ, CX = 100 pF 5.0 — 1.3 — — — 3.0 — — — — — µs RX = 10 kΩ, CX = 1000 pF 5.0 — 9 — — — 3.0 — — — — — µs RX = 10 kΩ, CX = 10000 pF 5.0 — 70 — — — 5.0 — ±0.1 — — — % RX = 10 kΩ, CX = 1000 pF Item Symbol t PHL t PHL t PLH Pulse width tw Output pulse width t WQ Pulse width match ∆tWQ between circuits in the same package Caution in use: In order to prevent any malfunctions due to noise, connect a high frequency performance capacitor between V CC and GND, and keep the wiring between the External components and Cext, Rext/Cext pins as short as possible. 6 HD74HC4538 Circuit Operation Fig. 3 shows the HC4538 configured in the retriggerable mode. Briefly, the device operates as follows (refer to Fig. 1): In the quiescent state, the external timing capacitor, CX, is charged to V CC. When a trigger occurs, the Q output goes high and CX discharges quickly to the lower references voltage (Vref Lower 1/3 V CC). CX then charges, through RX, back up to the upper reference voltage (Vref Upper 2/3 V CC), at which point the one-shot has timed out and the Q output goes low. The following, more detailed description of the circuit operation refers to both the function diagram (Fig. 1) and the timing diagram (Fig. 2) Quiescent State In the quiescent state, before an input trigger appears; the output latch is high and the reset latch is high (1 in Fig. 2). Thus the Q output (pin 6 or 10) of the monostable multivibrator is low (2 Fig. 2). The output of the trigger-control circuit is low (3), and transistors M1, M2, and M3 are turned off. The external timing capacitor, CX, is charged to VCC (4), and the upper reference circuit has a low output (5). Transistor M4 is turned on and analog switch S1 is turned off. Thus the lower reference circuit has V CC at the noninverting input and a resulting low output (6). In addition, the output of the trigger-control reset circuit is low. Trigger Operation The HC4538 is triggered by either a rising-edge signal as input A (7) or a falling-edge signal at input B (8), with the unused trigger input and the Reset input held at the voltage levels shown in the Function Table. Either trigger signal will cause the output of the trigger-control circuit to go high (9). The trigger-control circuit going high simultaneously initiates three events. First, the output latch goes low, thus taking the Q output of the HC4538 to a high state (10). Second, transistor M3 is turned on, which allows the external timing capacitor, CX, to rapidly discharge toward ground (11). (Note that the voltage across CX appears at the input of the upper reference circuit comparator). Third, transistor M4 is turned off and analog switch S1 is turned on, thus allowing the voltage across C X to also appear at the input of the lower reference circuit comparator. When CX discharges to the reference voltage of the lower reference circuit (12), the outputs of both reference circuits will be high (13). The trigger-control circuit flip-flop to a low state (14). This turns transistor M3 off again, allowing CX to begin to charge back up toward VCC, with a time constant t = RXCX (15). In addition, transistor M4 is turned on and analog switch S1 is turned off. Thus a high voltage level is applied to the input of the lower reference circuit comparator, causing its output to go low (16). The monostable multivibrator may be retriggered at any time after the trigger-control circuit goes low. When CX charges up to the reference voltage of the upper reference circuit (17), the output of the upper reference circuit goes low (18). This causes the output latch to toggle, taking the Q output of the HC4538 to a low state (19), and completing the time-out cycle. 7 HD74HC4538 Reset Operation A low voltage applied to the Reset pin always forces the Q output of the HC4538 to a low state. The timing diagram illustrates the case in which reset occurs (20) while C X is charging up toward the reference voltage of the upper reference circuit (21). When a reset occurs, the output of the reset latch goes low (22), turning on transistor M1. Thus CX is allowed to quickly charge up to VCC (23) to await the next trigger signal. Retrigger Operation When used in the retriggerable mode (Fig. 3), the HC4538 may be retriggered during timing out of the output pulse at any time after the trigger-control circuit flip-flopw has been reset (24). Because the triggercontrol circuit flip-flop resets shortly after CX has discharged to the reference voltage of the lower reference circuit (25), the minimum retrigger time, trr (Switching Waveform 1) is a function of internal propagation delays and the discharge time of CX: Fig. 4 shows the device configured in the non-retriggerable mode. Power-Down Considerations Large values of CX may cause problems when powering down the HC4538 because of the amount of energy stored in the capacitor. When a system containing this device is powered down, the capacitor may discharge from VCC through the input protection diodes at pin 2 or pin 14. Current through the protection diodes must be limited to 30 mA; therefore, the turn-off time of the V CC power supply must not be faster than t = VCC•CX/(30 mA). For example, if VCC = 5 V and CX = 15 µF, the VCC supply must turn off no faster than t = (5 V)•(15 µF)/30 mA = 2.5 ms. This is usually not a problem because power supplies are heavily filtered and cannot discharge at this rate. When a more rapid decrease of VCC to zero voltage occurs, the HC4538 may sustain damage. To avoid this possibility, use an external clamping diode. 8 HD74HC4538 VCC RX 2, 14 T2 CX VCC M1 M2 Upper Reference Circuit 2kΩ Output Latch + – M3 Vref Upper 6, 10 S1 M4 7, 9 Q + – 4, 12 Trigger-Control Circuit A Q Lower Reference Circuit VCC Vref Lower C Q B CR 5, 11 Trigger-Control Reset Circuit 3, 13 CD Reset Latch Fig. 1 Function Diagram 9 HD74HC4538 Quiescent State Trigger Cycle (A Input) Trigger Cycle (B Input) Reset Retrigger trr 7 Trigger Input A (Pin 4 or 12) Trigger Input B (Pin 5 or 11) 8 Reset Input CD (Pin 3 or 13) 21 24 9 14 3 Trigger-Control Circuit Output 11 4 T2 Input (Pin 2 or 14) 15 20 23 17 12 Vref Upper Vref Lower 13 Upper Reference Circuit Output 5 Lower Reference Circuit Output 6 Reset Latch Output 1 25 13 16 22 10 Q Output (Pin 6 or 10) 19 2 tWQ tWQ tWQ+trr tW (H) 50% A tW (L) B 50% tWQ tPLH Q tPLH 50% tPHL Q tPHL 50% A trr B 50% tf tr 50% CD tW (L) tPHL 50% tTLH 90% 10% Q tTHL Q 90% 10% 90% 10% tWQ+trr 50% (Retriggered Pulse) tPLH 50% Fig. 2 Timing Diagram 10 HD74HC4538 CX RX VCC T1 T2 Q A Rising-Edge Trigger B Q CD CX RX VCC T1 T2 Q A B Q Rising-Edge Trigger CD Fig. 3 Retriggerable Monostable Circuitry 11 HD74HC4538 CX RX VCC T1 T2 Q A Falling-Edge Trigger B Q CD CX RX VCC T1 T2 Q A B Q Falling-Edge Trigger CD Fig. 4 Nonritriggerable Monostable Circuitry 12 Unit: mm 19.20 20.00 Max 1 7.40 Max 9 6.30 16 8 1.3 0.48 ± 0.10 2.54 Min 5.06 Max 2.54 ± 0.25 0.51 Min 1.11 Max 7.62 + 0.13 0.25 – 0.05 0° – 15° Hitachi Code JEDEC EIAJ Weight (reference value) DP-16 Conforms Conforms 1.07 g Unit: mm 10.06 10.5 Max 9 1 8 1.27 *0.42 ± 0.08 0.40 ± 0.06 0.10 ± 0.10 0.80 Max *0.22 ± 0.05 0.20 ± 0.04 2.20 Max 5.5 16 0.20 7.80 +– 0.30 1.15 0° – 8° 0.70 ± 0.20 0.15 0.12 M *Dimension including the plating thickness Base material dimension Hitachi Code JEDEC EIAJ Weight (reference value) FP-16DA — Conforms 0.24 g Unit: mm 9.9 10.3 Max 9 1 8 0.635 Max *0.42 ± 0.08 0.40 ± 0.06 0.15 *0.22 ± 0.03 0.20 ± 0.03 1.27 0.11 0.14 +– 0.04 1.75 Max 3.95 16 0.10 6.10 +– 0.30 1.08 0° – 8° 0.67 0.60 +– 0.20 0.25 M *Dimension including the plating thickness Base material dimension Hitachi Code JEDEC EIAJ Weight (reference value) FP-16DN Conforms Conforms 0.15 g Cautions 1. Hitachi neither warrants nor grants licenses of any rights of Hitachi’s or any third party’s patent, copyright, trademark, or other intellectual property rights for information contained in this document. Hitachi bears no responsibility for problems that may arise with third party’s rights, including intellectual property rights, in connection with use of the information contained in this document. 2. Products and product specifications may be subject to change without notice. Confirm that you have received the latest product standards or specifications before final design, purchase or use. 3. Hitachi makes every attempt to ensure that its products are of high quality and reliability. However, contact Hitachi’s sales office before using the product in an application that demands especially high quality and reliability or where its failure or malfunction may directly threaten human life or cause risk of bodily injury, such as aerospace, aeronautics, nuclear power, combustion control, transportation, traffic, safety equipment or medical equipment for life support. 4. Design your application so that the product is used within the ranges guaranteed by Hitachi particularly for maximum rating, operating supply voltage range, heat radiation characteristics, installation conditions and other characteristics. Hitachi bears no responsibility for failure or damage when used beyond the guaranteed ranges. Even within the guaranteed ranges, consider normally foreseeable failure rates or failure modes in semiconductor devices and employ systemic measures such as failsafes, so that the equipment incorporating Hitachi product does not cause bodily injury, fire or other consequential damage due to operation of the Hitachi product. 5. This product is not designed to be radiation resistant. 6. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without written approval from Hitachi. 7. Contact Hitachi’s sales office for any questions regarding this document or Hitachi semiconductor products. Hitachi, Ltd. Semiconductor & Integrated Circuits. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan Tel: Tokyo (03) 3270-2111 Fax: (03) 3270-5109 URL NorthAmerica : http:semiconductor.hitachi.com/ Europe : http://www.hitachi-eu.com/hel/ecg Asia (Singapore) : http://www.has.hitachi.com.sg/grp3/sicd/index.htm Asia (Taiwan) : http://www.hitachi.com.tw/E/Product/SICD_Frame.htm Asia (HongKong) : http://www.hitachi.com.hk/eng/bo/grp3/index.htm Japan : http://www.hitachi.co.jp/Sicd/indx.htm For further information write to: Hitachi Semiconductor (America) Inc. 179 East Tasman Drive, San Jose,CA 95134 Tel: <1> (408) 433-1990 Fax: <1>(408) 433-0223 Hitachi Europe GmbH Electronic components Group Dornacher Stra§e 3 D-85622 Feldkirchen, Munich Germany Tel: <49> (89) 9 9180-0 Fax: <49> (89) 9 29 30 00 Hitachi Europe Ltd. Electronic Components Group. Whitebrook Park Lower Cookham Road Maidenhead Berkshire SL6 8YA, United Kingdom Tel: <44> (1628) 585000 Fax: <44> (1628) 778322 Hitachi Asia Pte. Ltd. 16 Collyer Quay #20-00 Hitachi Tower Singapore 049318 Tel: 535-2100 Fax: 535-1533 Hitachi Asia Ltd. Taipei Branch Office 3F, Hung Kuo Building. No.167, Tun-Hwa North Road, Taipei (105) Tel: <886> (2) 2718-3666 Fax: <886> (2) 2718-8180 Hitachi Asia (Hong Kong) Ltd. Group III (Electronic Components) 7/F., North Tower, World Finance Centre, Harbour City, Canton Road, Tsim Sha Tsui, Kowloon, Hong Kong Tel: <852> (2) 735 9218 Fax: <852> (2) 730 0281 Telex: 40815 HITEC HX Copyright ' Hitachi, Ltd., 1999. All rights reserved. Printed in Japan.