8 www.ti.com SLUS535C − MARCH 2003 − REVISED SEPTEMBER 2004 FEATURES DESCRIPTION D D D D The TPS4002x family of dc-to-dc controllers are designed for non-isolated synchronous buck regulators, providing enhanced operation and design flexability through user programmability. Operating Input Voltage 2.25 V to 5.5 V Output Voltage as Low as 0.7 V 1% Internal 0.7 V Reference Predictive Gate Drive N-Channel MOSFET Drivers for Higher Efficiency The TPS4002x utilizes a proprietary Predictive Gate Drive technology to minimize the diode conduction losses associated with the high-side and synchronous rectifier N-channel MOSFET transistions. The integrated charge pump with boost circuit provides a regulated 5-V gate drive for both the high side and synchronous rectifier N-channel MOSFETs. The use of the Predictive Gate Drive technology and charge pump/boost circuits combine to provide a highly efficient, smaller and less expensive converter. D Externally Adjustable Soft-Start and Short Circuit Current Limit D Programmable Fixed-Frequency 100 KHz-to-1 MHz Voltage-Mode Control D Source-Only Current or Source/Sink Current D Quick Response Output Transient Comparators with Power Good Indication Provide Output Status Design flexibility is provided through user programmability of such functions as: operating frequency, short circuit current detection thresholds, soft-start ramp time, and external synchronization frequency. The operating frequency is programmable using a single resistor over a frequency range of 100 kHz to 1 MHz. Higher operating frequencies yield smaller component values for a given converter power level as well as faster loop closure. D 16-Pin PowerPAD Package APPLICATIONS D D D D D Networking Equipment Telecom Equipment Base Stations Servers DSP Power VDD VDD 2.25 V − 5.5 V VOUT VOUT TPS40020 1 ILIM/ SYNC 2 VDD 3 OSNS 4 FB 5 BOOT1 16 HDRV 15 SW 14 BOOT2 13 COMP PVDD 12 6 SS/SD LDRV 11 7 RT PGND 10 8 SGND PWRGD 9 UDG−02094 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PowerPAD and Predictive Gate Drive are trademarks of Texas Instruments. !"#$ % &'!!($ #% )'*+&#$ ,#$(- !,'&$% &!" $ %)(&&#$% )(! $.( $(!"% (/#% %$!'"($% %$#,#!, 0#!!#$1!,'&$ )!&(%%2 ,(% $ (&(%%#!+1 &+',( $(%$2 #++ )#!#"($(!%- Copyright 2004, Texas Instruments Incorporated www.ti.com SLUS535C − MARCH 2003 − REVISED SEPTEMBER 2004 DESCRIPTION (CONTINUED) The short circuit current detection is programmable through a single resistor, allowing the short circuit current limit detection threshold to be easily tailored to accommodate different size (RDS(on)) MOSFETs. The short circuit current function provides pulse-by-pulse current limiting during soft-start and short term transient conditions as well as a fault counter to handle longer duration short circuit current conditions. If a fault is detected the controller shuts down for a period of time determined by six (6) consecutive soft-start cycles. The controller automatically retries the output every seventh (7th) soft-start cycle. In addition to determining the off time during a fault condition, the soft-start ramp provides a closed loop controlled ramp of the converter output during startup. Programmability allows the ramp rate to be adjusted for a wide variety of output L-C component values. The output voltage transient comparators provide a quick response , first strike, approach to output voltage transients. The output voltage is sensed through a resistor divider at the OSNS pin. If an overvoltage condition is detected the HDRV gate drive is shut-off and the LDRV gate drive is turned on until the output is returned to regulation. Similarly, if an output undervoltage condition is sensed the HDRV gate drive goes to 95% duty cycle to pump the output back up quickly. In either case, the PowerGood open drain output pulls low to indicate an output voltage out of regulation condition. The PowerGood output can be daisy-chained to the SS/SD pin or enable pin of other controllers or converters for output voltage sequencing. The transient comparators can be disabled by simply tying the OSNS pin to VDD. The TPS4002x can be externally synchronized through the ILIM/SYNC pin up to 1.5× the free-running frequency. This allows multiple contollers to be synchronized to eliminate EMI concerns due to input beat frequencies between controllers. INTERNAL BLOCK DIAGRAM VDD 2 VDD 0.719 V OSNS PWRGD 3 VDD SS ACTIVE 9 CHARGE PUMP 0.659 V FB 4 COMP 5 RT 7 0.69 V + + UVLO OSC DRV PREDICTIVE GATE DRIVE(tm) PWM LOGIC PWM CLK 13 BOOT2 12 PVDD 16 BOOT1 15 HDRV 14 SW 11 LDRV 10 PGND 1 ILIM/SYNC PVDD UVLO IRT DRV FAULT CLK SS/SD 6 SOFT START SS ACTIVE FAULT COUNTER + UVLO SD SYNC 0.28 V 8 − OC DCHG SGND IRT CURRENT LIMIT COMPARATOR VDD UVLO 1V UVLO DISABLE + + ISS VDD VDD 1.4 V UDG−02092 2 www.ti.com SLUS535C − MARCH 2003 − REVISED SEPTEMBER 2004 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. ORDERING INFORMATION TA LOAD CURRENT(1) PACKAGE Plastic HTSSOP (PWP)(2) Plastic HTSSOP (PWP)(2) SOURCE −40°C to 85°C SOURCE/SINK PART NUMBER TPS40020PWP TPS40021PWP (1) See page 7 for explanation. (2) The PWP package is also available taped and reeled. Add an R suffix to the device type (i.e., TPS40020PWPR). See the application section of the data sheet for PowerPAD drawing and layout information. ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range unless otherwise noted(4) TPS4002X SS/SD, VDD, PVDD, OSNS BOOT2, BOOT1 VSW + 6 −3.0 to 10.5 SW Input voltage range, VIN UNIT −0.3 to 6 SWT (SW transient < 50 ns) V −5 FB, ILIM −0.3 to 6.0 Output voltage range, VOUT COMP, PWRGD, RT Sink current, IS PWRGD −0.3 to 6 10 Operating virtual junction temperature range, TJ −40 to 125 Storage temperature, Tstg −55 to 150 mA °C C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds 260 (4) Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. RECOMMENDED OPERATING CONDITIONS MIN Input voltage, VIN 2.25 Operating junction temperature, TJ −40 NOM MAX UNIT 5.5 V 85 °C PWP PACKAGE(5)(6) (TOP VIEW) ILIM/SYNC VDD OSNS FB COMP SS/SD RT SGND 1 2 3 4 5 6 7 8 THERMAL PAD 16 15 14 13 12 11 10 9 BOOT1 HDRV SW BOOT2 PVDD LDRV PGND PWRGD (5) For more information on the PWP package, refer to TI Technical Brief, Literature No. SLMA002. (6) PowerPADt heat slug must be connected to SGND (Pin 8), or electrically isolated from all other pins. 3 www.ti.com SLUS535C − MARCH 2003 − REVISED SEPTEMBER 2004 ELECTRICAL CHARACTERISTICS TJ = −40°C to 85°C, TJ = TA, VDD = 5.0 V (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT INPUT SUPPLY VDD VPVDD IDD Input voltage range, VDD PVDD pin voltage 2.25 Switching current VDD = 3.3 V 500 kHz, No load on HDRV, LDRV Quiescent current FB = 0.8 V Shutdown current SS/SD = 0 V, Outputs OFF 5.2 3.5 5.0 V 2.0 3.0 0.38 1.00 1.95 2.05 2.15 V 80 130 200 mV 2.25 V ≤ VDD ≤ 5.00 V, RT = 69.8 kΩ 2.25 V ≤ VDD ≤ 5.00 V, RT = 34.8 kΩ 425 500 575 800 950 1100 VPEAK−VVAL 0.80 0.93 1.07 0.24 0.31 0.41 VOSNS = VDD, RT = 34.8 kΩ, VDD = 3.3 V, FB = 0 V 85% 94% VOSNS = VDD, RT = 70 kΩ, VDD = 5.0 V, FB = 0 V 90% 95% Minimum on-voltage VUVLO 5.50 4.9 Hysteresis mA OSCILLATOR fOSC Accuracy VRAMP Ramp voltage VVAL Ramp valley voltage kHz V PWM dMAX dMIN tMIN Maximum duty cycle Minimum duty cycle 0% Minimum HDRV on-time(2) 250 ns ERROR AMPLIFIER VFB IBIAS Feedback input voltage VOH VOL High-level output voltage IOH IOL High-level output source current GBW −40°C ≤ TA ≤ 85°C, 2.25V ≤ VDD ≤ 5.00V 0.685 Input bias current Low-level output voltage Low-level output sink current Gain bandwidth(1) IOH = 0.5 mA, VFB = GND IOL = 0.5 mA, VFB = VDD VFB = GND VFB = VDD AOL Open loop gain(1) CURRENT LIMIT ISINK VOS Current limit sink current tON tON Minimum HDRV on−time in overcurrent tSS VILIM Soft-start cycles 2.25 V ≤ VDD ≤ 5.00 V, RT = 69.8 kΩ Current limit offset voltage 2.0 0.697 V 30 130 nA 2.5 0.08 3 7 3 8 0.15 V mA 5 10 MHz 55 85 dB 165 190 215 µA −20 0 20 mV 200 300 VDD = 3.3 V Switch leading-edge blanking pulse time(1) Current limit input voltage range 0.690 ns 140 6 2 cycles VDD V 5.4 µA SOFT START ISS Soft-start source current Outputs = OFF (1) Ensured by design. Not production tested. (2) Operation below the minimum on-time could result in overlap of the HDRV and LDRV outputs. 4 2.0 3.3 www.ti.com SLUS535C − MARCH 2003 − REVISED SEPTEMBER 2004 ELECTRICAL CHARACTERISTICS (continued) TJ = −40°C to 85°C, TJ = TA, VDD = 5.0 V (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX Shutdown threshold voltage 0.22 0.26 0.29 Device enable threshold voltage 0.25 0.28 0.32 1.0 2.5 5.0 0.8 1.5 3.0 UNIT SHUTDOWN VSD VEN V OUTPUT DRIVER RLDHI RLDLO Low-side driver pull-up resistance V(BOOT1) − V(SW) = 3.3 V, ISOURCE = 100mA V(BOOT1) − V(SW) = 3.3 V, ISINK =100mA PVDD = 3.3 V, ISOURCE =100 mA Low-side driver pull-down resistance PVDD = 3.3 V, ISINK =100 mA tLRISE tLFALL Low-side driver rise time tHRISE tHFALL High-side driver rise time RHDHI High-side driver pull-up resistance RHDLO High-side driver pull-down resistance 1.0 2.5 5.0 0.45 0.80 1.50 15 35 10 25 15 35 10 25 Low-side driver fall time CLOAD = 1 nF High-side driver fall time Ω ns THERMAL SHUTDOWN TSD Shutdown temperature(1) Hysteresis(1) 165 °C 15 CHARGE PUMP RVB2 RB2P RDS(on) VDD to BOOT2 RDS(on) BOOT2 to PVDD VDD = 5.0 V, VDD = 5.0 V, ISOURCE =10 mA ISOURCE =10 mA 2.8 6.6 10.4 2.8 5.6 8.4 RPB1 RDS(on) PVDD to BOOT1 POWER GOOD VDD = 5.0 V, ISOURCE =10 mA 2.9 5.9 8.9 50 90 140 6 10 14 6 10 14 2 4 6 0.5 1.5 3.0 140 500 1000 140 500 1000 23 29 35 VPGD Pull-down voltage Output sense high to power good low delay tONHPL time Output sense low to power good low delay tONLPL time tSDHPH Shutdown high to power good high delay time tSDLPL Shutdown low to power good low delay time Output sense high to nominal to power good tONHPH high delay time Output sense low to nominal to power good tONLPH high delay time VOSNS = 0.8 V, IPWRGD =0.5 mA, VDD = 3.3 V 0.7 V ≤ VOSNS ≤ 0.8 V, IPWRGD =0.5 mA, VDD = 3.3 V 0.6 V ≤ VOSNS ≤ 0.7 V, IPWRGD =0.5 mA, VDD = 3.3 V VOSNS = 0.7 V, IPWRGD =0.5 mA, VDD = 3.3 V, 0.0 V ≤ VSS/SD ≤ 0.4 V VOSNS = 0.7 V, IPWRGD =0.5 mA, VDD = 3.3 V, 0.0 V ≤ VSS/SD ≤ 0.4 V 0.7 V ≤ VOSNS ≤ 0.8 V, IPWRGD =0.5 mA, VDD = 3.3 V 0.6 V ≤ VOSNS ≤ 0.7 V, IPWRGD =0.5 mA, VDD = 3.3 V Ω mV µss ns TRANSIENT COMPARATORS Overvoltage output threshold voltage VOV Hysteresis Undervoltage output threshold voltage VUV Referenced to VFB Hysteresis VDIS OSNS minimum disable voltage (1) Ensured by design. Not production tested. Referenced to VDD 8 15 22 −37 −31 −25 8 15 22 0.5 mV V 5 www.ti.com SLUS535C − MARCH 2003 − REVISED SEPTEMBER 2004 ELECTRICAL CHARACTERISTICS (continued) TJ = −40°C to 85°C, TJ = TA, VDD = 5.0 V (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT SYNCHRONIZATION VENSY Synchronization enable low threshold voltage VBLNK Synchronization current limit enable threshold voltage 0.7 Referenced to VDD tMIN Minimum synchronization input pulse width PREDICTIVE DELAY VSWP tLDHD tHDLD V −0.7 35 Sense voltage to modulate delay 50 −200 ns mV Maximum delay modulation LDRV OFF-to-HDRV ON 40 65 90 Counter delay/bit time LDRV OFF-to-HDRV ON 2.5 4.5 6.2 Maximum delay modulation HDRV OFF-to-LDRV ON 55 80 105 Counter delay/bit time HDRV OFF-to-LDRV ON 2.2 5.0 6.5 LDRV output = OFF −5 −2.5 2 ns RECTIFIER ZERO CURRENT COMPARATOR Sense voltage to turn off rectifier MOSFET VSW TPS40020 tZBLNK Zero current blanking time(1) (1) Ensured by design. Not production tested. 150 mV ns TERMINAL FUNCTIONS TERMINAL NAME NO. I/O DESCRIPTION BOOT1 16 I This pin provides a bootstrapped supply for the high side FET driver, enabling the gate of the high side FET to be driven above the input supply rail. Connect a capacitor from this pin to the SW pin. BOOT2 13 I This pin provides a secondary bootstrapping necessary for generation of PVDD. Connect a capacitor from this pin to SW. COMP 5 O Output of the error amplifier. Refer to Electrical Characteristics table for loading constraints. FB 4 I Inverting input of the error amplifier. In normal operation, VFB is equal to the internal reference level of 690 mV. HDRV 15 O The gate drive output for the high side N-channel MOSFET switch is bootstrapped to near PVDD for good enhancement of the high-side switch. The HDRV switches from BOOT1 to SW. ILIM/SYNC 1 I The current limit pin is used to set the current limit threshold. A current sink from this pin to GND sets the threshold voltage for output short circuit current across a resistor connected to VDD. Synchronization is accomplished by pulling IMAX to less than 1 V for a period greater than the minimum pulse width and then releasing. An open collector or drain device should be used. These pulses must be of higher frequency than the free running frequency of the local oscillator. LDRV 11 O Gate drive output for the low-side synchronous rectifier N-channel MOSFET. LDRV switches from PVDD to PGND. OSNS 3 O The output sense pin is connected to a resistor divider from VOUT to GND (identical to the main feedback loop) and is used to sense power good condition and provides reference for the transient comparators. PGND 10 O Power (high-current) ground used by LDRV. PWRGD 9 − Power good. This is an open-drain output which connects to the supply via an external resistor. PVDD 12 O This pin is the regulated output of the charge-pump and provides the supply voltage for the LDRV driver stage. PVDD also drives the bootstrap circuit which generates the voltage on BOOT1. RT 7 I External pin for programming the oscillator frequency. Connnected a resistor between this pin and GND. SGND 8 − Signal ground SS/SD 6 I The soft-start/shutdown pin provides user programmable soft-start timing and shutdown capability for the controller. SW 14 I This pin, used for overcurrent, zero-current, and in the anti-cross conduction sensing is connected to the switched node on the converter. Output short circuit is detected by sensing the voltage at this pin with respect to VDD while the high-side switch is on. Zero current is detected by sensing the pin voltage with respect to ground when the low-side rectifier MOSFET is on. VDD 2 I Power input for the device. Maximum voltage is 5.5 V. De-coupling of this pin is required. 6 www.ti.com SLUS535C − MARCH 2003 − REVISED SEPTEMBER 2004 APPLICATION INFORMATION The TPS4002x series of devices are low-input voltage, synchronous, voltage mode-buck controllers. A typical application circuit is shown in Figure 1. These controllers are designed to allow construction of high-performance dc-to-dc converters with input voltages from 2.25 V to 5.5 V, and output voltages as low as 690 mV. Using a top side N-channel MOSFET for the primary buck switch results in lower switch resistance for a given gate charge. The device controls the delays from main switch off to rectifier turn on and from rectifier turn off to main switch turn on in a way that minimizes diode losses (both conduction and recovery) in the synchronous rectifier. The reduction in these losses is significant and can mean that for a given converter power level, smaller FETs can be used, or that heat sinking can be reduced or even eliminated. The TPS40021 is the controller of choice for most general purpose synchronous buck designs, operating in two quadrant mode (i.e. source or sink current) full time. This choice provides the best performance for output voltage load transient response over the widest load current range. The TPS40020 operates in single quadrant mode (source current only) full time, allowing the paralleling of converters. Single quadrant operation ensures one converter does pull current from a paralleled converter. A converter using one of these controllers emulates a non-synchronous buck converter at light loads. When current in the output inductor attempts to reverse, an internal zero-current detection circuit turns OFF the synchronous rectifier and causes the current flow in the inductor to become discontinuous. At average load currents greater than the peak amplitude of the inductor ripple current, the converter returns to operation as a synchronous buck converter to maximize efficiency. The controller provides for a coarse short circuit current-limit function that provides pulse-by-pulse current limiting, as well as integrates short circuit current pulses to determine the existence of a persistant fault state at the converter output. If a fault is detected, the converter shuts down for a period of time (determined by six soft-start cycles) and then restarts. The current-limit threshold is adjustable with a single resistor connected from VDD to the ILIM/SYNC pin. This overcurrent function is designed to protect against catastrophic faults only, and cannot be guaranteed to protect against all overcurrent conditions. The controller implements a closed-loop soft start function. Startup ramp time is set by a single external capacitor connected to the SS/SD pin. The SS/SD pin also doubles as a shutdown function. VOLTAGE REFERENCE The bandgap cell is designed with a trimmed, curvature corrected (< 1%) 0.69-V output, allowing output voltages as low as 690 mV to be obtained. Oscillator The ramp waveform is a saw-tooth form at the PWM frequency with a peak voltage of 1.25 V, and a valley of 0.3 V. The PWM duty cycle is limited to a maximum of 97%, allowing the bootstrap and charge pump capacitors to charge during every cycle. 7 www.ti.com SLUS535C − MARCH 2003 − REVISED SEPTEMBER 2004 APPLICATION INFORMATION Bootstrap/Charge Pump The TPS4002X series includes a charge pump to boost the drive voltage to the power MOSFET’s to higher levels when the input supply is low. A capacitor connected from PVDD to PGND is the storage cap for the pump. A capacitor connected from SW to BOOT2 gets charged every switching cycle while LDRV is high and its charge is dumped on the PVDD capacitor when HDRV goes high. An internal switch disables the charge pump when the voltage on PVDD reaches approximately 4.8 V and enables pumping when PVDD falls to approximately 4.6 V. The high-side driver uses the capacitor from SW to BOOT1 as its power supply. When SW is low, this capacitor charges from the PVDD capacitor. When the SW pin goes high, this capacitor provides above-rail drive for the high-side N-channel FET. PVDD, BOOT1 and BOOT2 are pre-charged to the VDD voltage during a shutdown condition. For low-input voltage converters, utilizing higher gate threshold voltage MOSFETs, it may be necessary to add an Schottky diode from VDD (anode) to BOOT1 to guarantee sufficient voltage for initial start up. Once switching starts the charge pump reverses bias on the Schottky diode. When operating the TPS40020 under no load or extremely light-load conditions the controller will be operating in discontinuous Mode (DCM); reverse current is prevented from flowing in the synchronous rectifier. In DCM the on times for both the HDRV and LDRV pulses can become too narrow to provide adequate charging of PVDD and BOOT1 outputs, causing their voltages to collapse. Insufficient PVDD and BOOT1 voltages prevent the external MOSFETS from becomming fully enhanced, causing loss of converter output regulation. Schottky diodes from VIN (anode) to PVDD, and VIN (anode) to BOOT1, as well as a pre-load can be added to maintain PVDD and BOOT1 at voltage levels sufficient enough to fully enhance the external MOSFETs. The amount of pre-load typically ranges from 50 mA to 100 mA depending on operating conditions and external MOSFET selection. Drivers The HDRV and LDRV MOSFET drivers are capable of driving gate-to-source voltages up to 5.0 V. Using appropriate MOSFETs, a 25-A converter can be achieved. The LDRV driver switches between VDD and ground, while the HDRV driver is referenced to SW and switches between BOOT1 and SW. The maximum voltage between BOOT1 and SW is 5.0 V when PVDD is in regulation. 8 + C9 330 µF C8 330 µF R2 10 kΩ R4 118 kΩ C14 2200 pF C13 0.022 µF R7 30.1 kΩ C12 22 µF C15 47 pF C11 22 µF R6 10 kΩ C10 330 µF C16 R8 1800 pF 2.87 kΩ R5 8.66 kΩ + + R1 8.66 kΩ VDD 3.3 V FB 4 8 7 6 SGND RT SS/SD COMP OSNS 3 5 VDD PGND LDRV PVDD BOOT2 SW HDRV BOOT1 PWRGD PWP ILIM/SYNC TPS4002XPWP 2 1 R3 1.5 kΩ 9 10 11 12 13 14 15 16 C3 10 µF R9 10 kΩ Q2 Si7880DP C11 1 µF C2 1 µF C17 15 nF R10 2.2 Ω L1 0.75 µF Q1 Si7858DP + C4 470 µF + C5 470 µF + C6 470 mF UDG−03031 1.25 V 20 A C7 10 µF www.ti.com SLUS535C − MARCH 2003 − REVISED SEPTEMBER 2004 APPLICATION INFORMATION Figure 1. Typical Application 9 www.ti.com SLUS535C − MARCH 2003 − REVISED SEPTEMBER 2004 APPLICATION INFORMATION Synchronous Rectification and Predictive Delay In a normal buck converter, when the main switch turns off, current is flowing to the load in the inductor. This current cannot be stopped immediately without using infinite voltage. To give this current a path to flow and maintain voltage levels at a safe level, a rectifier or catch device is used. This device can be either a plain diode, or it can be a controlled active device if a control signal is available to drive it. The TPS4002X provides a signal to drive an N−channel MOSFET as a rectifier. This control signal is carefully coordinated with the drive signal for the main switch so that there is absolute minimum dead time from the time that the rectifier FET turns off and the main switch turns on, and minimum delay from when the main switch turns off and the rectifier FET turns on. This TI−patented function, predictive delay, uses information from the current switching cycle to adjust the delays that are used for the next cycle. Figure 2 shows the switch-node voltage waveform for a synchronously rectified buck converter. Illustrated are the relative effects of a fixed delay drive scheme (constant, pre-set delays for the turnoff to turn on intervals), an adaptive delay drive scheme (variable delays based upon voltages sensed on the current switching cycle) and the predictive delay drive scheme. Note that the longer the time spent in diode conduction during the rectifier conduction period, the lower the efficiency. Also, not shown in the figure, is the fact that the predictive delay circuit can actually prevent the body diode from becoming forward biased at all while at the same time avoiding cross conduction or shoot through. This results in a significant power savings when the main FET turns on. There is no reverse recovery loss in the body diode of the rectifier FET. GND Channel Conduction Body Diode Conduction Fixed Delay Adaptive Delay Predictive Delay Figure 2. Switch Node Waveforms for Synchronous Buck Converter 10 UDG−01144 www.ti.com SLUS535C − MARCH 2003 − REVISED SEPTEMBER 2004 APPLICATION INFORMATION Output Short Circuit Protection Output short circuit protection in the TPS4002x is sensed by looking at the voltage across the main FET while it is on. If the voltage exceeds a pre-set threshold, the current pulse is terminated, and a counter inside the device is incremented. If this counter fills up, a fault condition is declared and the chip disables switching for a period of time and then attempts to restart the converter with a full soft-start cycle. The more detailed explanation follows. In each switching cycle, a comparator looks at the voltage across the top side FET while it is on. If the voltage across that FET exceeds a programmable threshold voltage, then the current switching pulse is terminated and a 3-bit counter (eight counts) is incremented by one count. If during the switching cycle the top side FET voltage does not exceed a preset threshold, then this counter is decremented by one count. (The counter does not wrap around from seven to zero or from zero to seven). If the counter reaches a full count of seven, the device declares that a fault condition exists at the output of the converter. In this state, switching stops and the soft-start capacitor is discharged. The counter is decremented by one by the soft start cap discharge. When the soft-start capacitor is fully discharged, the discharge circuit is turned off and the cap is allowed to charge up at the nominal charging rate, When the soft-start capacitor reaches approximately 1.3 V, it is discharged again and the overcurrent counter is decremented by one count. The capacitor is charged and discharged, and the counter decremented until the count reaches zero (a total of six times). When this happens, the outputs are again enabled as the soft-start capacitor generates a reference ramp for the converter to follow while attempting to restart. During this soft-start interval (whether or not the controller is attempting to do a fault recovery or starting for the first time), pulse-by-pulse current limiting is in effect, but overcurrent pulses are not counted to declare a fault until the soft-start cycle has been completed. It is possible to have a supply try to bring up a short circuit for the duration of the soft-start period plus seven switching cycles. Power stage designs should take this into account if it makes a difference thermally. Figure 3 shows the details of the overcurrent operation. (+) VTS (−) Overcurrent Threshold Voltgage Internal PWM VTS 0V External Main Drive Normal Cycle Overcurrent Cycle UDG−03029 Figure 3. Switch Node Waveforms for Synchronous Buck Converter 11 www.ti.com SLUS535C − MARCH 2003 − REVISED SEPTEMBER 2004 APPLICATION INFORMATION Figure 4 shows the behavior of key signals during initial startup, during a fault and a successfully fault recovery. At time t0, power is applied to the converter. The voltage on the soft-start capacitor (VCSS) begins to ramp up At t1, the soft-start period is over and the converter is regulating its output at the desired voltage level. From t0 to t1, pulse-by-pulse current limiting was in effect, and from t1 onward, overcurrent pulses are counted for purposes of determining if a fault exists. At t2, a heavy overload is applied to the converter. This overload is in excess of the overcurrent threshold, the converter starts limiting current and the output voltage falls to some level depending on the overload applied. During the period from t2 to t3, the counter is counting overcurrent pulses and at time t3 reaches a full count of 7. The soft-start capacitor is then discharged, the outputs are disabled, the counter decremented, and a fault condition is declared. VDD 1.3 V 0.6 V 0.6 V VCSS FAULT ILOAD VOUT t0 Counter t1 t4 t2 t3 0 t5 6 1 2 3 4 5 5 6 7 t6 4 t7 3 cycles t8 2 t9 1 t t10 0 UDG−03187 Figure 4. Overcurrent/Fault Waveforms When the soft-start capacitor is fully discharged, it begins charging again at the same rate that it does on startup, with a nominal 3-µA current source. As the capacitor voltage reaches full charge, it is discharged again and the counter is decremented by one count. These transitions occur at t3 through t9. At t9, the counter has been decremented to zero. Now the fault logic is cleared, the outputs are enabled and the converter attempts to restart with a full soft-start cycle. The converter comes into regulation at t10. The internal SS signal is a diode drop below VCSS. When VCSS reaches one diode drop above ground, (≅0.6 V) the output (VOUT) begins it’s soft-start ramp. 12 www.ti.com SLUS535C − MARCH 2003 − REVISED SEPTEMBER 2004 APPLICATION INFORMATION Setting the Short Circuit Current Limit Threshold Connecting a resistor from VDD to ILIM sets the current limit. A current sink in the chip causes a voltage drop across the resistor connected to ILIM. This voltage drop is the short circuit current threshold for the part. The current that the ILIM pin sinks is dependent on the value of the resistor connected to RT and is given by: 0.69 V RT I ILIM + 19.0 (1) The tolerance of the current sink is too loose to do an accurate current limit. The main purpose is for hard fault protection of the power switches. Given the tolerance of the ILIM sink current, and the RDS(on) range for a MOSFET, it is generally possible to apply a load that thermally damages the converter. This device is intended for embedded converters where load characteristics are defined and can be controlled. A small capacitor can be added between ILIM and VDD for filtering. However, capacitors should not be used if the synchronization function is to be used. Soft-Start and Shutdown The soft-start and shutdown functions are common to the SS/SD pin. The voltage at this pin is the controlling voltage sent to the error amplifier during startup. This reduces the transient current required to charge the output capacitor at startup, and allows for a smooth startup with no overshoot of the output voltage. A shutdown feature can be implemented as shown in Figure 5. 3.3 µA 6 CSS SS/SD SHUTDOWN TPS4002x Figure 5. Shutdown Implementation C SS + I SS VFB t SS (F) (2) where D tSS is the start up time in seconds Switching Frequency The switching frequency is programmed by a resistor from RT to SGND. Nominal switching frequency can be calculated by: 3 R T (kW) + 37.736 10 * 5.09 (kW) f OSC(kHz) (3) 13 www.ti.com SLUS535C − MARCH 2003 − REVISED SEPTEMBER 2004 APPLICATION INFORMATION Synchronization The TPS4002x can be synchronized to an external reference frequency higher than the free running oscillator frequency. The recommended method is to use a diode and a push pull drive signal as shown in Figure 6. PREFERRED ALTERNATE VDD VDD TPS4002XPWP 50 ns to 100 ns Minumize Output/Stray Capacitance on ILIM Node TPS4002XPWP 1 ILIM/SYNC 1 ILIM/SYNC 2 VDD 2 VDD 50 ns to 100 ns UDG−03032 Figure 6. Synchronization Methods This design allows synchronization up to the maximum operating frequency of 1 MHz. For best results the nominal operating frequency of a converter that is to be synchronized should be kept as close as practicable to the synchronization frequency to avoid excessive noise induced pulse width jitter. A good target is to shoot for the free run frequency to be 80% of the synchronized frequency. This ensures that the synchronization source is the frequency determining element in the system and not to adversely affect noise immunity. Other methods of implementing the synchronization function include using an open collector or open drain output device directly, or discreet devices to pull the ILIM/SYNC pin down. These do work but performance can suffer at high frequency because the ILIM/SYNC pin must rise to (VDD − 1.0 V) before the next switching cycle begins. Any time that this requires is directly subtracted from the maximum pulse width available and should be considered when choosing devices to drive ILIM/SYNC. Consequently, the lowest output capacitance devices work best. During a synchronization cycle, the current sink on the ILIM/SYNC pin becomes disabled when ILIM/SYNC is pulled below 1.0 V. The ILIM/SYNC current sink remains disabled until ILIM/SYNC reaches (VDD −1.0 V) This removes the load on the ILIM/SYNC pin to allow the voltage to slew rapidly depending on the ILIM resistor and any stray capacitance on the pin. To maximize this slew rate, minimize stray capacitance on this pin. The duration of the synchronization pulse pulling ILIM/SYNC low shoud be between 50 ns and 100 ns. Longer durations may limit the maximum obtainable duty cycle. 14 www.ti.com SLUS535C − MARCH 2003 − REVISED SEPTEMBER 2004 APPLICATION INFORMATION Transient Comparators and Power Good The TPS4002x makes use of a separate pin, OSNS, to monitor output voltage for these two functions. In normal operation, OSNS is connected to the output via a resistor divider. It is important to make this divider the same ratio as the divider for the feedback network so that in normal operation the voltage at OSNS is the same as the voltage at FB, 0.69 V nominal. The PWRGD pin is an open drain output that is pulled low when the voltage at OSNS falls outside 0.69 V ±4.6% (approximately). A delay has been purposely built into the PWRGD pin pulling low in response to an out of band voltage on OSNS, to minimize the need for filtering the signal in the event of a noise glitch causing a brief out of band OSNS voltage. The PWRGD signal returns to high when the OSNS signal returns to approximately ±1% of nominal (0.69 V ±1%). The transient comparators override the conventional voltage control loop when the output voltage exceeds a ±4.6% window. If the output transition is high (i.e. load steps down from 90% load to 10 % load) then the HDRV gate drive is terminated, 0% duty cycle, the LDRV gate drive is turned on to sink output current until VOUT returns to within 1% of nominal. Conversely when VOUT drops outside the window (i.e. step load increases from 10% load to 90% load) HDRV increases to maximum duty cycle until VOUT returns to within 1% of nominal. (See Figure 7.) During start-up, the transient comparators control the state of PWRGD as previously described. However, the operation of the gate drive outputs is not affected. (See Figure 8) The transient comparators provide an improvement in load transient recovery time if used properly. In some situations, recovery time may be one half of the time required without transient comparators. Keep in mind that the transient comparator concept is a double-edged sword. While they provide improved transient recovery time, they can also lead to instability if incorrectly applied. For proper functionality, design a feedback loop for the converter that places the closed loop unity gain frequency at least five times higher than the 0 dB frequency of the output L-C filter. If not, the feedback loop cannot respond to the ring of the L-C on a transient event. The ring is likely to be large enough to disturb the transient comparators and the result is a power oscillator. Another helpful action is to ground the feedback loop divider and the OSNS divider at the SGND pin. Make sure both dividers measure the same physical location on the output bus. These help avoid problems with resistive drops at higher loads causing problems. Connecting OSNS to VDD disables the transient comparators. This also disables the PWRGD function. Alternatively, OSNS and FB can be tied together. This connection allows a proper PWRGD at startup, though transient performance diminishes. < 10 µs 4.6% 1% FB −1% − 4.6% − 4.6% 10 µs PWRGD 10 µ s 500 n s 500 n s SW 98 % Duty Cycle 0 % Duty Cycle 98 % Duty Cycle 0 % Duty Cycle UDG−03181 Figure 7. Duty Cycle Waveforms 15 www.ti.com SLUS535C − MARCH 2003 − REVISED SEPTEMBER 2004 APPLICATION INFORMATION VDD 1.3 V 0.6 V 0.3 V SS/SD VOUT − 1% 500 ns VOUT 4 µs PWRGD 1.5 µs Transient Comparators Enabled Transient Comparators Disabled UDG−03181 Figure 8. Transient Comparator Waveforms Layout Considerations Successful operation of the TPS4002x family of controllers is dependent upon the proper converter layout and grounding techniques. High current returns for the SR MOSFET’s source, input capacitance, output capacitance, PVDD capacitance, and input bypass capacitors (if applicable), should be kept on a single ground plane or wide trace connected to the PGND (pin10) through a short wide trace. Control components connected to signal ground, as well as the PowerPad thermal pad, should be connected to a single ground plane connected to SGND (Pin 8) through a short trace. SGND and PGND should be connected at a single point using a narrow trace. Proper operation of Predictive Gate Drive technology and IZERO functions are dependent upon detecting low-voltage thresholds on the SW node. To ensure that the signal at the SW pin accurately represents the voltage at the main switching node, the connection from SW (pin 14) to the main switching node of the converter should be kept as short and wide as possible and should ideally be kept on the top level with the power components. If the SW trace must traverse multiple board layers between the TPS4002x and the main switching node, multiple vias should be used to minimize the trace impedance. Gate drive outputs, LDRV and HDRV (pins 11 and 15, respectively) should be kept as short as possible to minimize inductances in the traces. If the gate drive outputs need to traverse multiple board layers multiple vias should be used. Charge pump components, BOOT1, BOOT2, PVDD, and any input bypass capacitors (if required), should be kept as close as possible to their respective pins. Ceramic bypass capacitors should be used if the input capacitors are located more than a couple of inches away from the TPS4002X. If a bypass capacitor is not needed the trace from the input capacitors to VDD (pin2) should be kept as short and wide as possible to minimize trace impedance. If multiple board layers are traversed multiple vias should be used. 16 www.ti.com SLUS535C − MARCH 2003 − REVISED SEPTEMBER 2004 APPLICATION INFORMATION Manufacturer’s instructions should be followed for proper layout of the external MOSFETs. Thermal impedances given in the manufacturer’s datasheets are for a given mounting technique with a specified surface area under the drain of the MOSFET. PowerPad package information can be found in the APPLICATION INFORMATION section of this datasheet. Refer to TPS40021 EVM−001 High Efficiency Synchronous Buck Converter with PWM Controller Evaluation Module (HPA009) User’s Guide, (Literature No. sluu144A) for a typical board layout. The PowerPAD package provides low thermal impedance for heat removal from the device. The PowerPAD derives its name and low thermal impedance from the large bonding pad on the bottom of the device. The circuit board must have an area of solder-tinned-copper underneath the package. The dimensions of this area depends on the size of the PowerPAD package. For a 16-pin TSSOP (PWP) package the area is 5 mm x 3.4 mm [3]. X: Minimum PowerPAD = 1.8 mm Y: Minimum PowerPAD = 1.4 mm Thermal Pad 4,50 mm 6,60 mm 4,30 mm 6,20 mm X 1 Y 8 Figure 9. PowerPAD Dimensions Thermal vias connect this area to internal or external copper planes and should have a drill diameter sufficiently small so that the via hole is effectively plugged when the barrel of the via is plated with copper. This plug is needed to prevent wicking the solder away from the interface between the package body and the solder-tinned area under the device during solder reflow. Drill diameters of 0.33 mm (13 mils) works well when 1-oz copper is plated at the surface of the board while simultaneously plating the barrel of the via. If the thermal vias are not plugged when the copper plating is performed, then a solder mask material should be used to cap the vias with a diameter equal to the via diameter of 0.1 mm minimum. This capping prevents the solder from being wicked through the thermal vias and potentially creating a solder void under the package. Refer to PowerPAD Thermally Enhanced Package[3] for more information on the PowerPAD package. 17 www.ti.com SLUS535C − MARCH 2003 − REVISED SEPTEMBER 2004 TYPICAL CHARACTERISTICS OSCILLATOR FREQUENCY vs JUNCTION TEMPERATURE MAXIMUM DUTY CYCLE vs JUNCTION TEMPERATURE 99 1000 950 fOSC − Oscillator Frequency − kHz Maximum Duty Cycle − % 98 97 96 VDD = 3.3 V, RT = 69.8 kΩ 95 94 900 RT = 35 kΩ 850 800 750 700 650 RT = 69.8 kΩ 600 550 500 VDD = 5 V, RT = 35 kΩ 93 −50 −25 0 25 50 75 100 450 −50 125 −25 0 75 100 125 100 125 Figure 11 Figure 10 SHUTDOWN SUPPLY CURRENT vs JUNCTION TEMPERATURE REFERENCE VOLTAGE vs JUNCTION TEMPERATURE 0.700 697 0.675 695 VREF − Reference Voltage − mV IDD − Shutdown Supply Current − mA 50 TJ − Junction Temperature − °C TJ − Junction Temperature − °C 0.650 0.625 0.600 0.575 0.550 0.525 0.500 −50 693 691 689 687 685 −25 0 25 50 75 TJ − Junction Temperature − °C Figure 12 18 25 100 125 683 −50 −25 0 25 50 75 TJ − Junction Temperature − °C Figure 13 www.ti.com SLUS535C − MARCH 2003 − REVISED SEPTEMBER 2004 TYPICAL CHARACTERISTICS SOFT-START CURRENT vs JUNCTION TEMPERATURE TIMING RESISTANCE vs SWITCHING FREQUENCY 3.50 1000 ISS − Soft-Start Sourcing Current − µA fOSC − Frequency − kHz 3.45 VIN = 3.9 V 900 800 700 600 500 400 300 200 3.40 3.35 3.30 3.25 3.20 3.15 3.10 3.05 100 20 40 60 80 100 120 140 3.00 −50 160 RT − Timing Resistance − kΩ −25 0 Figure 14 75 100 125 SHUTDOWN THRESHOLD VOLTAGE vs JUNCTION TEMPERATURE 0.30 20 0.29 VSS − Shutdown Threshold Voltage − V VDD = 2.0 V 15 VILIM − ILIM Offset Voltage − mV 50 Figure 15 ILIM OFFSET VOLTAGE vs JUNCTION TEMPERATURE 10 5 0 VDD = 3.2 V −5 −10 −15 −25 0 0.28 Enable 0.27 0.26 0.25 Disable 0.24 0.23 0.22 0.21 VDD = 4.9 V −20 −50 25 TJ − Junction Temperature − °C 25 50 75 TJ − Junction Temperature − °C Figure 16 100 125 0.20 −50 −25 0 25 50 75 100 125 TJ − Junction Temperature − °C Figure 17 19 www.ti.com SLUS535C − MARCH 2003 − REVISED SEPTEMBER 2004 TYPICAL CHARACTERISTICS ILIM SINK CURRENT vs JUNCTION TEMPERATURE 200 198 VDD = 3 V RT = 69.8 kΩ VDD = 3.3 V VOUT = 1.5 V fSW = 300 kHz VOUT IILIM − ILIM Sink Current − µA 196 194 192 190 LDRV 188 186 SW 184 182 180 −50 t − Time − 1 µs/div −25 0 25 50 75 100 125 TJ − Junction Temperature − °C Figure 19. TPS40020 Discontinuous Mode (DCM) Figure 18 VDD = 3.3 V VOUT = 1.5 V fSW = 300 kHz VOUT VDD = 3.3 V VOUT = 1.5 V fSW = 300 kHz SS/SD VOUT LDRV SW SW t − Time − 1 µs/div Figure 20. TPS40020 IZERO Detection − DCM 20 t − Time − 20 ms/div Figure 21. Output Current Fault Operation www.ti.com SLUS535C − MARCH 2003 − REVISED SEPTEMBER 2004 TYPICAL CHARACTERISTICS VDD = 3.3 V VOUT = 1.5 V fSW = 300 kHz ILOAD = 5 A SS/SD PVDD VDD = 3.3 V VOUT = 1.5 V fSW = 300 kHz ILOAD = 5 A SW VOUT PWRGD VOUT t − Time − 25 µs/div t − Time − 1 ms/div Figure 22. Start−Up Operation Without Transient Comparators VDD = 3.3 V VOUT = 1.5 V fSW = 300 kHz ILOAD = 5 A Figure 23. PVDD Hysteresis VDD = 3.3 V VOUT = 1.5 V fSW = 300 kHz ILOAD = 5 A SD SS/SD COMP SW VOUT PWRGD t − Time − 1 ms/div Figure 24. Start−Up Operation With Transient Comparators t − Time − 200 µs/div Figure 25. COMP Shutdown Operation 21 www.ti.com SLUS535C − MARCH 2003 − REVISED SEPTEMBER 2004 TYPICAL CHARACTERISTICS VDD = 3.3 V VOUT = 1.5 V fSW = 300 kHz VDD = 3.3 V VOUT = 1.5 V fSYNC = 330 kHz ILIM SW SS/SD PWRGD LDRV t − Time − 1 µs/div Figure 26. PWRGD Shutdown Operation 22 t − Time − 500 ns/div Figure 27. External Synchronization www.ti.com SLUS535C − MARCH 2003 − REVISED SEPTEMBER 2004 REFERENCE DESIGN This design used the TPS40020 PWM controller to facilitate a step-down application from 3.3-V to 1.5 V. (see Figure 29) Design specifications include: D Input voltage: 2.5 V ≤ VIN ≤ 5.0 V D Nominal output voltage: 3.3 V D Output voltage VOUT: 1.5 V D Output current IOUT: 20 A D Switching frequency: 300 kHz DESIGN PROCEDURE Setting the Frequency Choosing the optimum switching frequency is complicated. The higher the frequency, the smaller the inductance and capacitance needed, so the smaller the size, but then the the switching losses are higher, the efficiency is poorer. For this evaluation module, 300 kHz is chosen for reasonable efficiency and size. A resistor R4, which is connected from pin 7 to ground, programs the oscillator frequency. The approximate operating frequency is calculated in equation (3) 3 R T (kW) + 37.736 10 * 5.09 (kW) f OSC(kHz) (4) Using equation (2), RT is calculated to be 120 kΩ and a 118-kΩ resistor is chosen for 300 kHz operation. Inductance Value The inductance value can be calculated by equation (2). L (min) + ǒ V OUT f 1* I RIPPLE V OUT Ǔ VIN(max) (5) where IRIPPLE is the ripple current flowing through the inductor, which affects the output voltage ripple and core losses. Based on 24% ripple current and 300 kHz, the inductance value is calculated to 0.71 µH and a 0.75-µH inductor (part number is CDEP149−0R7) is chosen. The DCR of this inductor is 1.1 mΩ and the loss is 440 mW, which is approximately 1.5% of output power. C OUT(min) + I RIPPLE 8 f VRIPPLE (6) V ESR OUT + RIPPLE I RIPPLE (7) With 1.2% output voltage ripple, the needed capacitance is at least 109 µF and its ESR should be less than 3.75 mΩ. Three 2-V, 470-µF, POSCAP capacitors from Sanyo are used. The ESR is 10 mΩ each. The required input capacitance is calculated in equation (5). The calculated value is approximately 390 µF for a 100-mV input ripple. Three 6.0-V, 330-µF POSCAP capacitors with 10 mΩ ESR are used to handle 10 A of RMS input current. Additionally, two ceramic capacitors are used to reduce the switching ripple current. C IN(min) + I OUT(max) D(max) f OSC 1 V IN(ripple) (8) 23 3.3 V + 24 R6 10 kΩ C9 330 µF + R2 10 kΩ C16 R8 2.87 kΩ 1800 pF C8 330 µF + R1 8.66 kΩ C10 330 µF C12 22 µF C13 0.022 µF R17 30.1 kΩ R4 118 kΩ C14 220 pF SW 14 SGND PWP 8 PWRGD 9 PGND 10 LDRV 11 PVDD 12 BOOT2 13 RT SS/SD COMP FB OSNS 7 6 5 4 3 HDRV 15 2 VDD ILIM/SYNC BOOT1 16 TPS4002XPWP 1 R3 1.43 kΩ C15 47 pF R5 8.66 kΩ C11 22 µF C3 10 µF R9 10 kΩ Q2 S7880DP C2 1 µF C1 1 µF C17 15 nF R10 2.2 Ω L1 0.75 µF Q1 Si7858DP + C4 470 µF + C5 470 µF + C6 470 mF C7 10 µF 1.5 V 20 A SLUS535C − MARCH 2003 − REVISED SEPTEMBER 2004 www.ti.com REFERENCE DESIGN UDG−03031 Figure 28. Reference Design Schematic www.ti.com SLUS535C − MARCH 2003 − REVISED SEPTEMBER 2004 REFERENCE DESIGN Input and Output Capacitors The output capacitance and its ESR needed are calculated in equations (5) and (6). Compensation Design Voltage-mode control is used in this evaluation module, using R2, R7, R8, C14, C15, and C16 to form a Type-III compensator network. The L-C frequency of the power stage is approximately 4.9-kHz and the ESR-zero is around 34 kHz. The overall crossover frequency, f0db, is chosen at 43-kHz for reasonable transient response and stability. Two zeros fZ1 and fZ2 from the compensator are set at 2.4 kHz and 4 kHz. The two poles, fP1 and fP2 are set at 34 kHz and 115 kHz. The frequency of poles and zeros are defined by the following equations: f Z1 + 2p 1 R7 C14 f Z2 + 2p 1 R2 C16 f P1 + 2p 1 R8 C16 f P2 + 2p 1 R7 C15 (9) (assuming R2 ơ R8) (10) (11) (assuming C14 ơ C15) (12) The transfer function for the compensator is calculated in equation (10). (1 ) s A(s) + s R2 C14 C14 ƪǒ R7) Ǔ 1 ) C15 ) s C14 [1 ) s C16 (R2 ) R3)] R7 C15 (1 ) s ƫ R8 C16) (13) Figure 30 shows the close loop gain and phase. The overall crossover frequency is approximately 30 kHz. The phase margin is 57°. OVERALL GAIN AND PHASE vs OSCILLATOR FREQUENCY 50 200 Gain 40 150 30 Gain − dB 10 0 50 Phase 0 −10 −20 Phase − ° 100 20 −50 −30 −100 −40 −50 100 1k 10 k fOSC − Oscillator Frequency − kHz −150 100 k Figure 29. 25 www.ti.com SLUS535C − MARCH 2003 − REVISED SEPTEMBER 2004 REFERENCE DESIGN MOSFETs and Diodes For a 1.5-V output voltage, the lower the RDS(on) of the MOSFET, the higher the efficiency. Due to the high current and high conduction loss, the MOSFET should have very low conduction resistance (RDS(on)) and thermal resistance. Si7858DP is chosen for its low RDS(on) (between 3 mΩ and 4 mΩ) and Power-Pak package. Current Limiting Resistor R3 sets the short current limit threshold. The RDS(on) of the upper MOSFET is used as a current sensor. The current limit, IOUT(CL) is initialized at 30% above the maximum output current, IOUT(max), which is 28 A. Then R3 can be calculated in equation (11) and yields a value of 1.4 kΩ. An R3 of 1.43 kΩ is selected. I LIM + R3 + ǒ 19 K Ǔ V FB R4 RDS(on) ǒ + 19 I OUT(CL) I LIM Ǔ 0.69 V + 111.1 (mA) 118 kW + 1.5 0.004 I LIM (14) 28 A + 1.4 (kW) (15) where D D D D RDS(on) is the on-resistor of Q1 (4 mΩ) Temperature coefficient, K=1.5 VFB = 0.69 V R4=118 kΩ Voltage Sense Regulator R1 and R2 operate as the output voltage divider. The error amplifier reference voltage (VFB) is 0.69 V. The relationship between the output voltage and divider is described in equation (8). Using a 10-kΩ resistor for R2 and 1.5-V output regulation, R1 is calculated as 8.52 kΩ, 8.66 kΩ is selected for R1. V FB R1 + V OUT 1.5 V ³ 0.69 V + ³ R1 + 8.52 kW R1 ) R2 R1 R1 ) 10 kW (16) Transient Comparator The output voltage transient comparators provide a quick response, first strike, approach to output voltage transients. The output voltage is sensed through a resistor divider at the OSNS pin, using R5 and R6 shown in Figure 28. If an overvoltage condition is detected, the HDRV gate drive is shut off and the LDRV gate drive is turned on until the output is returned to regulation. Similarly, if an output undervoltage condition is sensed, the HDRV gate drive goes to 95% duty cycle to pump the output back up quickly. The voltage divider should be exactly the same as resistors R1 and R2 discussed previously. Resistor R5=8.66 kΩ and R6=10 kΩ in this evaluation module. 26 www.ti.com SLUS535C − MARCH 2003 − REVISED SEPTEMBER 2004 REFERENCE DESIGN TEST RESULTS Efficiency Curves The tested efficiency at different loads and input voltages are shown in Figure 30. The maximum efficiency is as high as 93% at 1.5-V output. The efficiency is around 88% when the load current (ILOAD) is 20 A. EFFICIENCY vs OUTPUT LOAD CURRENT 0.95 VIN = 2.5 V Efficiency − % 0.90 0.85 VIN = 4.0 V 0.80 VIN = 5.0 V VIN = 3.3 V 0.75 0.70 0 5 10 15 20 ILOAD − Load Current − A Figure 30. Typical Operating Waveforms Typical operating waveforms are shown in Figure 31 and 32. VIN = 3.3 V ILOAD = 20 A VIN = 3.3 V ILOAD = 20 A VOUTac (10 mV/div) VSW (2 V/div) t − Time − 1 µs/div Figure 31 t − Time − 1 µs/div Figure 32 27 www.ti.com SLUS535C − MARCH 2003 − REVISED SEPTEMBER 2004 REFERENCE DESIGN Transient Response and Output Ripple Voltage The output ripple is about 15 mVP−P at 20-A output. When the load changes from 4 A to 20 A, the overshooting voltage is about 35 mV. Figures 33 and 34 show the transient waveform with and without the transient comparator. Using the transient comparator yields a settling time of 10-µs faster than without. The output ripple is about 15 mVP−P at 20-A output which is shown in Figure 33. When the load changes from 0 A to 13 A, the overshoot voltage is approximately 80 mV, and the undershoot is is approximately 60 mV as shown in Figure 35. When the transient comparator is triggered, the powergood (PWRGD) signal goes low. VOUTac (50 mV/div) IOUT (10 A/div) t − Time − 200 µs/div VIN = 3.3 V VIN = 3.3 V WIthout Transient Comparator WIth Transient Comparator WIth Transient Comparator WIthout Transient Comparator IOUT (10 A/div) IOUT (10 A/div) t − Time − 10 µs/div Figure 33. Transient Response Undershoot 28 t − Time − 10 µs/div Figure 34. Transient Response Overshoot www.ti.com SLUS535C − MARCH 2003 − REVISED SEPTEMBER 2004 REFERENCE DESIGN VPWRGD (2.5 V/div) VOUTac (100 mV/div) IOUT (10 A/div) t − Time − 200 µs/div Figure 35. Transient Response 29 PACKAGE OPTION ADDENDUM www.ti.com 8-Mar-2005 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty TPS40020PWP ACTIVE HTSSOP PWP 16 TPS40020PWPR ACTIVE HTSSOP PWP 16 TPS40021PWP ACTIVE HTSSOP PWP 16 TPS40021PWPR ACTIVE HTSSOP PWP TPS40021PWPRG4 PREVIEW HTSSOP PWP 90 Lead/Ball Finish MSL Peak Temp (3) Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR 16 2000 90 None Call TI Call TI (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - May not be currently available - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. None: Not yet available Lead (Pb-Free). Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Green (RoHS & no Sb/Br): TI defines "Green" to mean "Pb-Free" and in addition, uses package materials that do not contain halogens, including bromine (Br) or antimony (Sb) above 0.1% of total product weight. (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDECindustry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2005, Texas Instruments Incorporated