ETC ECG005C

ECG005
The Communications Edge TM
InGaP HBT Gain Block
Product Features
• DC – 4 GHz
• +18 dBm P1dB at 1 GHz
• +34 dBm OIP3 at 1 GHz
• 19.5 dB Gain at 1 GHz
• 3.3 dB Noise Figure at 2 GHz
• Available in SOT-86 and
SOT-89 Package Styles
• Internally matched to 50 Ω
Product Information
Product Description
Functional Diagram
The ECG005 is a general-purpose buffer amplifier that
offers high dynamic range in a low-cost surface-mount
package. At 1000 MHz, the ECG005 typically provides
19.5 dB of gain, +34 dBm Output IP3, and +18 dBm P1dB.
GND
4
The ECG005 consists of Darlington pair amplifiers using
the high reliability InGaP/GaAs HBT process technology
and only requires DC-blocking capacitors, a bias resistor,
and an inductive RF choke for operation. The device is
ideal for wireless applications and is available in low-cost,
surface-mountable plastic SOT-86 and SOT-89 packages.
All devices are 100% RF and DC tested.
1
2
3
RF IN
GND
RF OUT
ECG005B
GND
4
Applications
•
•
•
•
•
•
Mobile Infrastructure
CATV / DBS
W-LAN / ISM
RFID
Defense / Homeland Security
Fixed Wireless
The broadband MMIC amplifier can be directly applied to
various current and next generation wireless technologies
such as GPRS, GSM, CDMA, and W-CDMA. In addition,
the ECG005 will work for other various applications within
the DC to 4 GHz frequency range such as CATV and fixed
wireless.
3 RF Out
1
2
GND
ECG005C
Specifications (1)
Parameter
RF In
Typical Performance (3)
Units
Min
MHz
MHz
dB
dBm
dBm
MHz
dB
dB
dB
dBm
dBm
dB
V
mA
DC
Operational Bandwidth
Test Frequency
Gain
Output P1dB
Output IP3 (2)
Test Frequency
Gain
Input Return Loss
Output Return Loss
Output P1dB
Output IP3 (2)
Noise Figure
Device Voltage
Device Current
17.5
+16.5
+30
4.2
Typ
1000
19.7
+18
+34
2000
18.5
16
13
+17.5
+32
3..3
4.8
65
Max
Parameter
4000
Frequency
S21
S11
S22
Output P1dB
Output IP3
Noise Figure
Units
MHz
dB
dB
dB
dBm
dBm
dB
Typical
500
20.5
-16
-13
+17.8
+33
5.2
900
19.7
-16
-13
+18
+34
3.4
1900
18.7
-16
-11
+17.5
+32
3.3
2140
18.5
-16
-11
+19.0
+30.5
3.8
3. Test conditions: T = 25º C, Supply Voltage = +6 V, Device Voltage = +5.0V, Rbias = 18 Ω, 50 Ω System.
5.3
1. Test conditions unless otherwise noted: 25º C, Supply Voltage = +6 V, Rbias = 18 Ω, 50 Ω System.
2. 3OIP measured with two tones at an output power of +4 dBm/tone separated by 1 MHz. The
suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule.
Absolute Maximum Rating
Parameter
Rating
Operating Case Temperature
Storage Temperature
-40 to +85 °C
-55 to +150 °C
Device Current
130 mA
RF Input Power (continuous)
Junction Temperature
+12 dBm
+250° C
Ordering Information
Part No.
Description
ECG005B
ECG005C
ECG005B-PCB
ECG005C-PCB
InGaP HBT Gain Block (SOT-89 Pkg)
InGaP HBT Gain Block (SOT-86 Pkg)
700 –2400 MHz Fully Assembled Eval. Board
700 –2400 MHz Fully Assembled Eval. Board
Operation of this device above any of these parameters may cause permanent damage.
Specifications and information are subject to change without notice
WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: [email protected] • Web site: www.wj.com
August 2004
ECG005
The Communications Edge TM
InGaP HBT Gain Block
Product Information
Typical Device RF Performance
Supply Bias = +6 V, Rbias = 18 Ω, Icc = 65 mA
Frequency
S21
S11
S22
Output P1dB
Output IP3
Noise Figure
MHz
dB
dB
dB
dBm
dBm
dB
100
20.5
-18.6
-16
+17.5
+33.6
5.4
500
20.5
-18.5
-15.2
+17.8
+33.5
5.3
900
19.7
-18
-17
+18
+34
3.5
1900
18.7
-21.5
-16
+17.6
+32
3.3
2140
18.5
-24
-17
+17.3
+31.5
3.3
2400
18.2
-27
-17
+17.1
+31
3.3
3500
16.9
-28
-15
+16
5800
14.1
-22
-8
1. Test conditions: T = 25º C, Supply Voltage = +6 V, Device Voltage = 4.8 V, Rbias = 18 Ω, Icc = 65 mA typical, 50 Ω System.
2. 3OIP measured with two tones at an output power of +4.5 dBm/tone separated by 1 MHz. The suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule.
3. Data is shown as device performance only. Actual implementation for the desired frequency band will be determined by external components shown in the application circuit.
Small Signal Gain
Icc vs Vde
25
160
140
120
100
15
Icc (mA)
Gain (dB)
20
10
80
25°C
60
40
5
25°C
-40°C
20
85°C
0
0
0.5
1
1.5
2
2.5
0
Frequency (GHz)
3
4
35
5
NF (dB)
OIP3 (dBm)
6
30
25
5
6
Vde (V)
Noise Figure vs. Frequency
40
P1dB vs. Frequency
24
4
20
16
3
25°C
20
0.5
2
P1dB (dBm)
OIP3 vs. Frequency
1
1
-40°C
85°C
1.5
Frequency (GHz)
2
25°C
2.5
2
0.5
1
1.5
Frequency (GHz)
2
12
0.5
1
-40°C
1.5
Frequency (GHz)
85°C
2
2.5
Specifications and information are subject to change without notice
WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: [email protected] • Web site: www.wj.com
August 2004
ECG005
The Communications Edge TM
InGaP HBT Gain Block
Product Information
Recommended Application Circuit
Vcc
Icc = 65 mA
R4
Bias
Resistor
C4
Bypass
Capacitor
C3
0.018 µF
L1
RF Choke
RF IN
RF OUT
ECG005
C2
Blocking
Capacitor
C1
Blocking
Capacitor
ECG005B-PCB
Reference
Designator
L1
C1, C2, C4
50
820 nH
.018 µF
ECG005C-PCB
Recommended Component Values
Frequency (MHz)
500
900
1900
2200
220 nH
68 nH
27 nH
22 nH
1000 pF
100 pF
68 pF
68 pF
2500
18 nH
56 pF
3500
15 nH
39 pF
1. The proper values for the components are dependent upon the intended frequency of operation.
2. The following values are contained on the evaluation board to achieve optimal broadband performance:
Ref. Desig.
L1
C1, C2
C3
C4
R4
Value / Type
39 nH wirewound inductor
56 pF chip capacitor
0.018 µF chip capacitor
Do Not Place
18 Ω 1% tolerance
Size
0603
0603
0603
0805
Recommended Bias Resistor Values
Supply
R1 value
Size
Voltage
6V
18.5 ohms
0805
7V
33.8 ohms
1210
8V
49 ohms
1210
9V
65 ohms
2010
10 V
80 ohms
2010
12 V
111 ohms
2512
The proper value for R1 is dependent upon the supply
voltage and allows for bias stability over temperature.
WJ recommends a minimum supply bias of +6 V. A
1% tolerance resistor is recommended.
Specifications and information are subject to change without notice
WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: [email protected] • Web site: www.wj.com
August 2004
ECG005
The Communications Edge TM
InGaP HBT Gain Block
Product Information
ECG005B (SOT-89 Package) Mechanical Information
Outline Drawing
Product Marking
The component will be marked with an
“E005” designator with an alphanumeric lot
code on the top surface of the package.
Tape and reel specifications for this part are
located on the website in the “Application
Notes” section.
MSL / ESD Rating
ESD Rating:
Value:
Test:
Standard:
Class 1A
Passes between 250 and 500V
Human Body Model (HBM)
JEDEC Standard JESD22-A114
MSL Rating: Level 3 at +235° C convection reflow
Standard:
JEDEC Standard J-STD-020
Land Pattern
Mounting Config. Notes
Specifications and information are subject to change without notice
WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: [email protected] • Web site: www.wj.com
August 2004
ECG005
The Communications Edge TM
InGaP HBT Gain Block
Product Information
ECG005C (SOT-86 Package) Mechanical Information
Outline Drawing
Product Marking
The component will be marked with a twodigit numeric lot code followed by a “U”
designator on the top surface of the
package.
Tape and reel specifications for this part are
located on the website in the “Application
Notes” section.
MSL / ESD Rating
ESD Rating:
Value:
Test:
Standard:
Class 1A
Passes between 250 and 500V
Human Body Model (HBM)
JEDEC Standard JESD22-A114
MSL Rating: Level 1 at +235° C convection reflow
Standard:
JEDEC Standard J-STD-020
Land Pattern
Mounting Config. Notes
Specifications and information are subject to change without notice
WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: [email protected] • Web site: www.wj.com
August 2004
ECG005
The Communications Edge TM
InGaP HBT Gain Block
Product Information
Typical Device S-Parameters – ECG005B
S-Parameters (Vdevice = +4.8 V, ICC = 65 mA, T = 25°C, calibrated to device leads)
Freq (MHz)
50
500
1000
1500
2000
2500
3000
3500
4000
4500
5000
5500
6000
S11 (dB)
S11 (ang)
S21 (dB)
S21 (ang)
S12 (dB)
S12 (ang)
S22 (dB)
S22 (ang)
-16.85
-16.24
-16.15
-16.13
-16.39
-16.93
-17.48
-19.28
-22.47
-26.44
-20.72
-15.55
-11.74
0.19
-9.81
-23.76
-36.75
-53.28
-68.72
-84.38
-104.57
-127.54
176.75
103.65
71.92
56.37
20.38
20.10
19.70
19.18
18.69
18.08
17.46
16.92
16.40
15.87
15.29
14.59
13.77
177.50
157.54
136.72
116.48
97.62
78.80
61.38
44.01
27.02
9.47
-7.89
-25.94
-43.60
-22.71
-22.66
-22.59
-22.49
-22.17
-21.86
-21.45
-20.94
-20.58
-20.05
-19.62
-19.45
-19.41
-0.45
-4.10
-8.40
-12.64
-15.97
-20.64
-26.00
-32.14
-38.33
-45.70
-54.19
-64.15
-74.67
-14.14
-13.67
-12.86
-11.87
-10.87
-10.22
-9.40
-8.82
-7.90
-6.94
-5.89
-4.89
-3.97
-3.11
-37.18
-71.27
-99.50
-125.35
-146.72
-168.24
171.86
151.59
131.25
111.91
93.31
75.59
Typical Device S-Parameters – ECG005C
S-Parameters (Vdevice = +4.8 V, ICC = 65 mA, T = 25°C, calibrated to device leads)
Freq (MHz)
50
500
1000
1500
2000
2500
3000
3500
4000
4500
5000
5500
6000
S11 (dB)
S11 (ang)
S21 (dB)
S21 (ang)
S12 (dB)
-17.40
-16.88
-16.10
-15.40
-14.93
-14.80
-15.00
-15.73
-16.71
-17.78
-18.95
-19.34
-17.30
0.37
-1.35
-5.64
-12.39
-21.87
-30.63
-41.19
-52.97
-64.36
-83.08
-109.86
-143.64
-177.52
20.68
20.43
19.87
19.09
18.33
17.48
16.61
15.87
15.22
14.60
14.02
13.44
12.82
177.99
159.13
139.68
121.78
105.90
90.63
77.28
64.50
52.26
39.83
28.04
15.46
3.40
-22.91
-22.93
-22.86
-22.84
-22.59
-22.31
-21.91
-21.49
-20.89
-20.28
-19.60
-18.99
-18.32
S12 (ang)
-0.12
0.51
1.14
2.39
4.51
4.94
5.67
5.29
5.81
4.59
2.50
-0.17
-3.34
S22 (dB)
S22 (ang)
-14.59
-14.73
-14.87
-14.84
-14.56
-14.02
-13.32
-12.63
-11.63
-10.76
-9.79
-8.81
-7.70
-2.72
-29.09
-56.63
-82.79
-106.69
-127.58
-146.19
-162.63
-177.32
168.36
155.83
143.13
131.06
Specifications and information are subject to change without notice
WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: [email protected] • Web site: www.wj.com
August 2004