ECM168 The Communications Edge TM PHS +34 dBm 10V Module Product Features • 1.9 GHz Power Amp Module • +34 dBm Linear Output Power • 33 dB Gain • Single +10V Supply • No negative voltage required • Low cost metal package • MTTF > 100 Years Applications • PAS Base Stations • Repeaters Product Information Product Description Functional Diagram The ECM168 is a high performance PAS Amplifier Module offering excellent linearity. The internally matched multi-stage amplifier has 33.5 dB gain while achieving +34 dBm linear output power to meet PHS requirements of better than -65 dBc ACLR at a ±600 kHz offset from the carrier. 1 The ECM168 uses a high reliability InGaP/GaAs HBT process technology and does not require any external matching components. The module has an added benefit by not require any negative biasing voltages; an internal active bias allows the ECM168 to maintain high linearity over temperature and operate directly off a single +10V supply. A low-cost metal housing allows the device to have a low thermal resistance and achieves over 100 years MTTF. All devices are 100% RF and DC tested. 2 3 4 5 6 Top View Pin No. 1 2 3 4 5 6 Case Function RF Output Vcc2 No Connect Vcc1 No Connect RF Input Ground The ECM168 is targeted for use as a driver amplifier in wireless infrastructure where high linearity and high power is required. This combination makes the device an excellent candidate for next generation PAS base stations. Specifications (1) Parameter Symbol Units f Ga MHz dB ACLR (±600kHz) Padj1 dBc ACLR (±900kHz) Input VSWR 2nd Order Harmonic Distortion 3rd Order Harmonic Distortion Supply Voltage Supply Current Padj2 dBc 2fo 3fo Vcc1, Vcc2 Id dBc dBc V mA Frequency Power Gain Min Typ Max 1880 - 1920 32.5 33.5 35.5 -67 -65 -69 -74 -70 1.5 -50 -50 +10 1000 1300 1100 Test Conditions Pout = +34 dBm, Vd = 10V Pout = +34 dBm, Vd = 10V Pout = +33.5 dBm, Vd = 10V Pout = +34 dBm, Vd = 10V Pout = +34 dBm, Vd = 10V Pout = +34 dBm, Vd = 10V Pout = +34 dBm, Vd = 10V 1. Test conditions unless otherwise noted: 25º C, Supply Voltage = +10 V, Output Power = +34 dBm, RF signal modulation is per PHS RCR-28. Absolute Maximum Rating Parameter Operating Case Temperature Storage Temperature Input RF Power Supply Voltage Rating -35 to +55 °C -55 to +150 °C +10 dBm +12 V Ordering Information Part No. Description ECM168 ECM168-PCB PHS +34 dBm 10V Module Fully Assembled Evaluation Board Operation of this device above any of these parameters may cause permanent damage. Specifications and information are subject to change without notice WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: [email protected] • Web site: www.wj.com December 2004 ECM168 The Communications Edge TM PHS +34 dBm 10V Module Product Information Recommended Application Circuit Please note that for reliable operation, the evaluation board will have to be mounted to a much larger heat sink during operation and in laboratory environments to dissipate the power consumed by the device. The use of a convection fan is also recommended in laboratory environments. Performance Graphs Gain vs. Channel Power ACLR vs. Channel Power ACLR vs. Channel Power 1900 MHz, PHS Signal, 192 kHz BW 1900 MHz, ±600 kHz offset, PHS Signal, 192 kHz BW 1900 MHz, ±900 kHz offset, PHS Signal, 192 kHz BW -64 35 -68 25°C -35°C 25°C 55°C 34 -66 -70 33 -68 -72 32 -70 -74 -72 -76 31 -35°C 25°C 55°C 29 31 30 -74 25 27 33 35 -35°C 55°C -78 25 Output Channel Power (dBm) 27 29 31 33 35 25 Output Channel Power (dBm) 27 29 31 33 35 Output Channel Power (dBm) Power Added Efficiency vs. Channel Power Icc vs. Channel Power 1900 MHz, PHS Signal, 192 kHz BW 1900 MHz, PHS Signal, 192 kHz BW 1150 30 -35°C 25 25°C 55°C 1100 20 1050 15 1000 10 5 950 0 900 25 27 29 31 33 Output Channel Power (dBm) 35 25 -35°C 25°C 55°C 27 29 31 33 35 Output Channel Power (dBm) Specifications and information are subject to change without notice WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: [email protected] • Web site: www.wj.com December 2004 ECM168 The Communications Edge TM PHS +34 dBm 10V Module Product Information Outline Drawing A 4X R=1.2 Top View Side View 1 2 3 4 5 6 // 0.10 A Lead 6X Cover PCB Heat Sink NOTE: UNLESS OTHERWISE SPECIFIED TYPICAL DIMENSIONS ARE IN MM. PIN ASSIGNMENT Front View (1) RFout, (2) Vcc2, (3) N/C, (4) Vcc1, (5) N/C, (6) RFin, Case:GND. Specifications and information are subject to change without notice WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: [email protected] • Web site: www.wj.com December 2004