TI TPS54120RGYT

TPS54120
www.ti.com
SBVS180C – JANUARY 2012 – REVISED JUNE 2012
Low-Noise, 1-A Power Supply
with Integrated DC-DC Converter and Low-Dropout Regulator
FEATURES
DESCRIPTION
•
The TPS54120 combines the high-efficiency of a
step-down switching (dc-dc) converter with a high
power-supply rejection (PSR), low-noise, low-dropout
regulator (LDO) to provide an ultra low-noise power
supply that delivers quiet power rails to noisesensitive applications.
1
•
•
•
•
•
Low-Noise Output: 17 µVRMS at 100 Hz to
1 MHz
Wide Input Voltage Range: 4.5 V to 17 V
High Efficiency: 72% at 1 A, 12V Input
Excellent Load/Line Transient Response
Synchronizable to External Clock: 200 kHz to
1.2 MHz
Small Package: 3.5 mm × 5.5 mm QFN-24
With a wide input range of 4.5 V to 17 V, the
TPS54120 is ideally suited for systems with 12-V
power busses, and supports a 1-A continuous output
current. The output voltage can be set from 0.8 V to
6.0 V using external resistors. The dc-dc converter
and LDO are completely configurable, allowing the
TPS54120 to be used in a wide range of low-noise
applications. In addition, the TPS54120 includes
features such as softstart, switching frequency
synchronization, and a power-good signal.
APPLICATIONS
•
•
•
•
•
•
Telecom Infrastructure
Pico and Femto Base Stations
Powering Sensitive Clocking Distribution
Circuits
Test and Measurement
Powering RF Components: VCOs, Receivers,
ADCs
Professional Audio
The device is available in a space-saving, 3.5-mm ×
5.5-mm QFN package, and is specified to operate
over a –40°C to +125°C junction temperature range.
FUNCTIONAL BLOCK DIAGRAM
L1
CBOOT
BOOT PH
VIN
R1
R2
CDC-DC_OUT
LDOIN
LDOEN
VSENSE
R4
PVIN
ON/OFF
EN
V(OUT)
OUT
VIN
TPS54120
COUT
FB
R5
RT/CLK
SS
RRT
COMP
CSS
NR
GND
C2
CNR
R3
C1
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2012, Texas Instruments Incorporated
TPS54120
SBVS180C – JANUARY 2012 – REVISED JUNE 2012
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
PACKAGE INFORMATION (1)
(1)
PRODUCT
PACKAGE-LEAD
PACKAGE DESIGNATOR
SPECIFIED JUNCTION
TEMPERATURE RANGE
TPS54120
QFN-24
RGY
-40°C to +125°C
For the most current package and ordering information see the Package Option Addendum at the end of this document, or visit the
device product folder on www.ti.com.
ABSOLUTE MAXIMUM RATINGS (1)
Over operating temperature range (unless otherwise noted).
VALUE
MIN
MAX
–0.3
20
V
PH
–1
20
V
PH (10ns transient)
–3
–1
V
–0.3
27
V
V
VIN, PVIN
BOOT
BOOT – PH
Voltage
0
7
LDOIN, OUT
–0.3
7
LDOEN
–0.3
VLDOIN + 0.3 (2)
V
EN, RT/CLK, PWRGD
–0.3
6
V
VSENSE, COMP, SS
–0.3
3
V
FB, NR
–0.3
3.6
V
OUT
Internally limited
RT/CLK
Current
Temperature
Electrostatic discharge ratings
(1)
(2)
UNIT
A
±100
µA
PH
Internally limited
PVIN
Internally limited
A
A
COMP
±200
µA
PWRGD (sinking)
–0.1
5
mA
Operating junction, TJ
–40
+150
°C
Storage, Tstg
–55
+150
°C
2
kV
500
V
Human body model (HBM)
Charged device model (CDM)
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated is not implied. Exposure to absolutemaximum rated conditions for extended periods may affect device reliability.
VEN absolute maximum rating is VLDOIN + 0.3 V or +7.0 V, whichever is smaller.
THERMAL INFORMATION
TPS54120
THERMAL METRIC
(1)
RGY (QFN)
UNITS
24 PINS
θJA
Junction-to-ambient thermal resistance
45.1
θJC(top)
Junction-to-case(top) thermal resistance
48.2
θJB
Junction-to-board thermal resistance
22.0
ψJT
Junction-to-top characterization parameter
2.1
ψJB
Junction-to-board characterization parameter
21.9
θJC(bottom)
Junction-to-case(bottom) thermal resistance
8.6
(1)
2
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS54120
www.ti.com
SBVS180C – JANUARY 2012 – REVISED JUNE 2012
ELECTRICAL CHARACTERISTICS
At TJ = –40°C to +125°C, V(PVIN) = V(VIN) = 12 V, V(LDOIN) = DC-DC_OUT (1) = 4.1 V, V(OUT) = 3.3 V, I(OUT) = 10 mA,
V(EN) = floating, C(OUT) = 100 μF, unless otherwise noted.
TPS54120
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
POWER SUPPLY (VIN AND PVIN PINS)
V(PVIN)
V(VIN)
PVIN pin input voltage range
1.6
17
V
VIN pin input voltage range
4.5
17
V
UVLO threshold
VIN rising
4.0
UVLO hysteresis
4.5
V
150
ISD(VIN)
VIN pin shutdown current
V(EN) = 0 V
IOP
VIN pin operating current (no switching)
V(VSENSE) = 810 mV
mV
2
5
µA
600
800
µA
2.1
3
V
DC-DC BOOT (BOOT PIN)
(VBOOT – VPH) UVLO
DC-DC CONVERTER ENABLE (EN PIN)
VIL(EN)
EN pin low-level input voltage
Falling
VIH(EN)
EN pin threshold
Rising
1.10
1.17
1.21
V
I(EN)
EN pin input current
V(EN) = 1.1 V
1.15
µA
EN pin hysteresis current
V(EN) = 1.3 V
3.4
µA
1.26
V
DC-DC CONVERTER VOLTAGE REFERENCE
Vref
Reference voltage
0 A ≤ I(OUT) ≤ 1 A
0.792
0.800
0.808
V
DC-DC MOSFET
RHS
High-side switch resistance
RLS
Low-side switch resistance
V(BOOT) – V(PH) = 3 V
77
V(BOOT) – V(PH) = 6 V
57
103
mΩ
mΩ
V(VIN) = 12 V
50
87
mΩ
DC-DC ERROR AMPLIFIER
gM
I(COMP)
Error amplifier transconductance
–2 µA ≤ I(COMP) ≤ 2 µA, V(COMP) = 1 V
Error amplifier dc gain
V(SENSE) = 0.8 V
Error amplifier output current
V(COMP) = 1 V, 100-mV input overdrive
1000
Switching start threshold
1300
µMho
3100
V/V
±110
µA
0.25
COMP pin to ISWITCH gM
V
12
A/V
4.2
6.2
A
3.8
5.8
A
1
2.6
A
512
cycles
16384
cycles
DC-DC CURRENT LIMIT
ILIM(HS)
ILIM(LS)
High-side switch current limit
Low-side switch current limit
Sourcing
Sinking
Wait time before triggering protection
Wait time before start
DC-DC SOFT-START (SS PIN)
SS pin charge current
SS pin to VSENSE pin matching
2.3
V(SS) = 0.4 V
29
µA
60
mV
DC-DC POWER GOOD (PWRGD PIN )
VSENSE pin threshold
VSENSE falling (fault, undervoltage)
0.91Vref
V
VSENSE rising (good, undervoltage)
0.94Vref
V
VSENSE rising (fault, overvoltage)
1.09Vref
V
VSENSE falling (good, overvoltage)
1.06Vref
High-level output leakage current
V(VSENSE) = Vref, V(PWRGD) = 5.5 V
Low-level output voltage
I(PWRGD) = 2 mA
Minimum VIN voltage for valid output
V(PWRGD) < 0.5 V at 100 µA
Minimum SS voltage for PWRGD valid
(1)
30
V
100
nA
0.3
V
0.6
1
V
1.2
1.4
V
DC-DC_OUT refers to the regulated output voltage of the switching regulator (see Figure 28).
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
3
TPS54120
SBVS180C – JANUARY 2012 – REVISED JUNE 2012
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
At TJ = –40°C to +125°C, V(PVIN) = V(VIN) = 12 V, V(LDOIN) = DC-DC_OUT(1) = 4.1 V, V(OUT) = 3.3 V, I(OUT) = 10 mA,
V(EN) = floating, C(OUT) = 100 μF, unless otherwise noted.
TPS54120
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
LDO
V(LDOIN)
LDO input voltage range
V(FB)
FB pin voltage
V(OUT)
OUT pin voltage range
2.2
V(FB)
OUT pin voltage accuracy
I(OUT) ≤ 1 A, V(OUT_nom) + 0.5 V ≤ V(LDOIN) ≤ 6.5 V,
V(FB) ≤ V(OUT) < 6.0 V
Load regulation
100 mA ≤ I(OUT) ≤ 1 A
ΔVO(ΔVI)
Line regulation
I(OUT) = 100 mA, V(OUT_nom) + 0.5 V ≤ V(LDOIN) ,
4.5 V ≤ V(VIN) ≤ 17 V
VDO
LDO dropout voltage
I(OUT) ≤ 1 A, 2.5 V ≤ V(LDOIN) ≤ 6.5 V,
V(FB) = GND
ILIM
Output current limit
V(OUT) = 0.85 × V(OUT_nom)
I(GND)
GND pin current
I(OUT) ≤ 1 A
IL(sd_LDO)
Shutdown current (I(GND))
V(EN) < 0.3 V
I(FB)
FB pin current
I(LDOEN)
LDOEN pin input current
VIL(LDOEN)
LDOEN pin low-level input voltage
(disable)
VIH(LDOEN)
LDOEN pin high-level input voltage
(enable)
ΔVO(ΔIL)
6.5
0.8
–3.0%
V
6.0
±0.3%
µV/mA
100
µV/V
500
1.4
mV
2
A
350
µA
2
µA
1.0
V(EN) = V(LDOIN)
V
3.0%
5
1.1
V
20
µA
nA
0.4
1.4
V
V
DC-DC TIMING RESISTOR AND EXTERNAL CLOCK (RT/CLK PIN)
Switching frequency range (RT mode set
point and PLL mode)
200
1200
kHz
Minimum switching frequency
R(RT) = 240 kΩ (1%)
160
200
240
kHz
Switching frequency
R(RT) = 100 kΩ (1%)
400
480
560
kHz
Maximum switching frequency
R(RT) = 40.2 kΩ (1%)
1080
1200
1320
kHz
RT/CLK high threshold
2
V
RT/CLK low threshold
0.8
Minimum pulse width
V
20
ns
RT/CLK falling edge to PH rising edge
delay
Measure at 500 kHz with RT resistor in series
62
ns
minimum on time
Measured at 90% of PH, TA = 25°C, IPH = 2 A
97
ns
minimum off time
BOOT – PH > 3 V
0
ns
Shutdown, temperature increasing
+160
°C
Reset, temperature decreasing
+140
°C
PH PIN
THERMAL SHUTDOWN
TSD
Thermal shutdown temperature
NOISE
Vn
4
Output noise voltage
Submit Documentation Feedback
BW = 100 Hz to 100 kHz, C(OUT) = 100 µF,
C(NR) = 0.01 µF, C(FB) = 0.01 µF, I(OUT) = 100 mA
9
µVRMS
BW = 100 Hz to 1 MHz, C(OUT) = 100 µF,
C(NR) = 0.01 µF, C(FB) = 0.01 µF, I(OUT) = 100 mA
17
µVRMS
BW = 10 Hz to 1 MHz, C(OUT) = 100 µF,
C(NR) = 0.01 µF, C(FB) = 0.01 µF, I(OUT) = 100 mA
21
µVRMS
W = 10 Hz to 10 MHz, C(OUT) = 100 µF,
C(NR) = 0.01 µF, C(FB) = 0.01 µF, I(OUT) = 100 mA
38
µVRMS
Copyright © 2012, Texas Instruments Incorporated
TPS54120
www.ti.com
SBVS180C – JANUARY 2012 – REVISED JUNE 2012
PIN CONFIGURATION
RGY PACKAGE
QFN-24
(TOP VIEW)
OUT
LDOIN
1
24
OUT
2
23
LDOIN
FB
3
22
NR
GND
4
21
LDOEN
NC
5
20
NC
RT/CLK
6
19
PWRGD
PGND
7
18
BOOT
PGND
8
17
PH
PVIN
9
16
PH
PVIN
10
15
EN
VIN
11
14
SS
Thermal
Pad
12
13
VSENSE
COMP
PIN DESCRIPTIONS
PIN
NAME
NO.
DESCRIPTION
BOOT
18
A bootstrap capacitor is required between the BOOT and PH pins. The voltage on this capacitor carries the gate
drive voltage for the high-side MOSFET of the dc-dc converter.
COMP
13
DC-DC error amplifier output, and input to the output switch current comparator. Connect frequency compensation to
this pin.
EN
15
Active-high enable pin for dc-dc converter. Float this pin to enable. Adjust the input undervoltage lockout with two
resistors.
FB
3
This pin is the input to the control-loop error amplifier of the LDO and is used to set its output voltage.
GND
4
LDO ground
LDOEN
21
Driving this pin high turns on the LDO regulator. Driving this pin low puts the LDO regulator into shutdown mode.
The EN pin must not be left floating and can be connected to LDOIN if not used.
LDOIN
23, 24
LDO input
NC
5, 20
No internal connection
NR
22
LDO noise reduction pin. Connect an external capacitor between this pin and ground to reduce output noise to very
low levels, and slow down the VOUT ramp (RC soft-start) of the LDO.
OUT
1, 2
LDO output. A 4.7-µF or larger capacitor is required for stability.
PGND
7, 8
Return for the dc-dc control circuitry and low-side power MOSFET of the dc-dc converter.
PH
16, 17
DC-DC converter switch node
PVIN
9, 10
DC-DC converter power input. Supplies the power switches of the dc-dc converter.
PWRGD
19
Open-drain power good fault pin for the dc-dc converter output. Asserts low as a result of thermal shutdown,
undervoltage, overvoltage, EN pin shutdown, or during soft-start of the dc-dc converter.
RT/CLK
6
Automatically selects between RT mode and CLK mode. An external timing resistor adjusts the switching frequency
of the device. In CLK mode, the device synchronizes to an external clock.
SS
14
DC-DC converter soft-start pin. Connect an external capacitor to this pin to set the internal reference voltage rise
time on the dc-dc converter. The voltage on this pin overrides the internal reference on the dc-dc converter.
VIN
11
Supplies the control circuitry of the dc-dc converter.
VSENSE
12
Inverting input of the gM error amplifier of the dc-dc converter.
Thermal pad
GND; for best noise performance, the thermal pad should be connected to the LDO GND and to a large ground pad
for thermal dissipation.
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
5
TPS54120
SBVS180C – JANUARY 2012 – REVISED JUNE 2012
www.ti.com
FUNCTIONAL BLOCK DIAGRAM
PWRGD
Ip
Ih
Thermal
SD
UVLO
Shutdown
Logic
+
EN Threshold -
PVIN
Thermal
SD
UV
EN
VIN
OV
Boot
Charge
PWRGD
Logic
BOOT
Current
Sense
VSENSE
-
SS
+
REF
Power Stage
Dead Time
and
Slew RateControl
Logic
+
COMP
PH
REG
PLL
RT/CLK
Current
Sense
Thermal
SD
Shutdown
Logic
LDOEN
PGND
UVLO
Current
Limit
LDOIN
OUT
33 kΩ
225 kΩ
REF
+
FB
NR
6
Submit Documentation Feedback
GND
Thermal Pad
Copyright © 2012, Texas Instruments Incorporated
TPS54120
www.ti.com
SBVS180C – JANUARY 2012 – REVISED JUNE 2012
TYPICAL CHARACTERISTICS
At V(PVIN) = V(VIN)= 12 V, V(LDOIN) = DC-DC_OUT = 4.1 V, V(OUT) = 3.3 V, I(OUT) = 10 mA, V(EN) = floating, COUT = 100 μF, and
CSS = CNR = 0.01µF (see Figure 28), unless otherwise noted.
LOAD REGULATION
LOAD REGULATION UNDER LIGHT LOADS
3.399
3.399
+ 125°C
+ 85°C
+ 25°C
0°C
− 40°C
3.366
3.333
VOUT (V)
VOUT (V)
3.333
+ 125°C
+ 85°C
+ 25°C
0°C
− 40°C
3.366
3.3
3.267
3.3
3.267
3.234
3.234
NOTE: Y axis shows 1% VOUT per division
3.201
0
NOTE: Y axis shows 1% VOUT per division
3.201
100 200 300 400 500 600 700 800 900 1000
IOUT (mA)
G001
0
5
10
15
IOUT (mA)
Figure 1.
LINE REGULATION
LINE REGULATION UNDER LIGHT LOADS
IOUT = 10 mA
+ 125°C
+ 85°C
+ 25°C
0°C
− 40°C
3.366
+ 125°C
+ 85°C
+ 25°C
0°C
− 40°C
3.366
3.333
VOUT (V)
3.333
VOUT (V)
G002
3.399
IOUT = 1 A
3.3
3.267
3.3
3.267
3.234
3.234
NOTE: Y axis shows 1% VOUT per division
3.201
4.5
6.5
8.5
10.5
12.5
VIN (V)
NOTE: Y axis shows 1% VOUT per division
14.5
16.5
3.201
4.5
18.5
6.5
8.5
G003
10.5
12.5
VIN (V)
14.5
16.5
18.5
G004
Figure 3.
Figure 4.
LDO DROPOUT VOLTAGE
vs LDO INPUT VOLTAGE
POWER-SUPPLY RIPPLE REJECTION
vs LDO DROPOUT VOLTAGE
500
100
IOUT = 1 A
+ 125°C
+ 85°C
+ 25°C
0°C
− 40°C
400
350
90
70
300
250
200
60
50
40
150
30
100
20
50
10
2
2.5
3
3.5
4
4.5
VLDOIN (V)
Figure 5.
Copyright © 2012, Texas Instruments Incorporated
5
5.5
6
IOUT = 100 mA
80
PSRR (dB)
450
VDO (mV)
25
Figure 2.
3.399
0
20
6.5
G005
0
f = 1 kHz
f = 100 kHz
f = 1 MHz
f = 10 MHz
0
0.5
1
1.5
2
VDO (V)
2.5
3
3.5
G006
Figure 6.
Submit Documentation Feedback
7
TPS54120
SBVS180C – JANUARY 2012 – REVISED JUNE 2012
www.ti.com
TYPICAL CHARACTERISTICS (continued)
At V(PVIN) = V(VIN)= 12 V, V(LDOIN) = DC-DC_OUT = 4.1 V, V(OUT) = 3.3 V, I(OUT) = 10 mA, V(EN) = floating, COUT = 100 μF, and
CSS = CNR = 0.01µF (see Figure 28), unless otherwise noted.
POWER-SUPPLY RIPPLE REJECTION
vs LDO DROPOUT VOLTAGE
POWER-SUPPLY RIPPLE REJECTION
vs FREQUENCY
100
100
90
90
IOUT = 1 A
80
80
70
PSRR (dB)
PSRR (dB)
70
60
50
40
30
10
0
0
0.5
1
1.5
2
VDO (V)
2.5
3
0
3.5
100
1k
10k
100k
Frequency (Hz)
1M
10M
G008
Figure 7.
Figure 8.
LDO OUTPUT CURRENT LIMIT
vs TEMPERATURE
OUTPUT SPECTRAL NOISE DENSITY
vs FREQUENCY
10
Output Noise (uV/rtHz)
ILIM (mA)
10
G007
1400
1200
VLDOIN = 2.2 V
VLDOIN = 3.8 V
VLDOIN = 5.5 V
VLDOIN = 6.5 V
1000
800
−40 −25 −10
5
20 35 50 65
Temperature (°C)
80
95
RMS Noise (100 Hz to 100 kHz)
8.9 µVRMS (CNR = 0.01 µF)
8.9 µVRMS (CNR = 0.1 µF)
8.9 µVRMS (CNR = 1 µF)
1
CNR = 0.01 µF
CNR = 0.1 µF
CNR = 1 µF
0.1
0.01
110 125
10
100
1k
G009
10k
100k
Frequency (Hz)
1M
10M
G010
Figure 9.
Figure 10.
OUTPUT SPECTRAL NOISE DENSITY
vs FREQUENCY
OUTPUT SPECTRAL NOISE DENSITY
vs FREQUENCY
10
10
RMS Noise (100 Hz to 100 kHz)
9.0 µVRMS (IOUT = 10 mA)
8.9 µVRMS (IOUT = 100 mA)
8.9 µVRMS (IOUT = 500 mA)
8.9 µVRMS (IOUT = 1 A)
1
Output Noise (uV/rtHz)
Output Noise (uV/rtHz)
IOUT = 100 mA
IOUT = 500 mA
IOUT = 1 A
10
1600
IOUT = 10 mA
IOUT = 100 mA
IOUT = 500 mA
IOUT = 1 A
0.1
10
100
1k
10k
100k
Frequency (Hz)
Figure 11.
8
40
20
1800
0.01
50
30
f = 1 kHz
f = 100 kHz
f = 1 MHz
f = 10 MHz
20
60
Submit Documentation Feedback
1M
10M
G011
RMS Noise (100 Hz to 100 kHz)
8.3 µVRMS (COUT = 10 µF)
8.3 µVRMS (COUT = 47 µF)
8.9 µVRMS (COUT = 100 µF)
1
COUT = 10 µF
COUT = 47 µF
COUT = 100 µF
0.1
0.01
10
100
1k
10k
100k
Frequency (Hz)
1M
10M
G012
Figure 12.
Copyright © 2012, Texas Instruments Incorporated
TPS54120
www.ti.com
SBVS180C – JANUARY 2012 – REVISED JUNE 2012
TYPICAL CHARACTERISTICS (continued)
At V(PVIN) = V(VIN)= 12 V, V(LDOIN) = DC-DC_OUT = 4.1 V, V(OUT) = 3.3 V, I(OUT) = 10 mA, V(EN) = floating, COUT = 100 μF, and
CSS = CNR = 0.01µF (see Figure 28), unless otherwise noted.
START-UP TIME
vs LDO NOISE-REDUCTION CAPACITANCE
LINE TRANSIENT RESPONSE
19
18
RLOAD = 33 Ω
CSS = 0.01 µF
0.02
VOUT Deviation
VIN= 7 V to 12 V to 7 V (1 V/µs)
10
12
−0.04
10
−0.06
8
−0.08
6
1
−0.02
14
1
10
100
−0.1
0
1k
CNR (nF)
50 µs/div
Figure 14.
LOAD TRANSIENT RESPONSE
VOUT Deviation
5
RLOAD = 33 Ω
0.01
−0.03
−0.05
1
−0.07
EN
VEN, VOUT (V)
IOUT= 100 mA to 1 A to 100 mA (1 A/µs)
4
VOUT Deviation (V)
−0.01
1.5
IOUT (A)
ENABLE PULSE RESPONSE
0.03
2
3
OUT
2
−0.09
0.5
1
−0.11
−0.13
0
0
10 µs/div
G015
10 ms/div
G016
Figure 16.
POWER-UP/POWER-DOWN RESPONSE
OSCILLATOR FREQUENCY
vs TEMPERATURE
490
VIN
VDC−DC_OUT
VOUT
8
fSW − Oscillator Frequency (dB)
VEN = VIN
VLDOEN = VDC−DC_OUT
9
7
6
5
4
3
2
1
0
0
Figure 15.
10
VIN, VDC−DC_OUT, VOUT (V)
G014
G013
Figure 13.
0
VOUT Deviation (V)
0
16
100
VIN (V)
From VIN(= EN) to 90% VOUT (ms)
1000
485
480
475
470
−40 −25 −10
0
20 ms/div
Figure 17.
Copyright © 2012, Texas Instruments Incorporated
G017
5
20 35 50 65
Temperature (°C)
80
95
110 125
G018
Figure 18.
Submit Documentation Feedback
9
TPS54120
SBVS180C – JANUARY 2012 – REVISED JUNE 2012
www.ti.com
TYPICAL CHARACTERISTICS (continued)
At V(PVIN) = V(VIN)= 12 V, V(LDOIN) = DC-DC_OUT = 4.1 V, V(OUT) = 3.3 V, I(OUT) = 10 mA, V(EN) = floating, COUT = 100 μF, and
CSS = CNR = 0.01µF (see Figure 28), unless otherwise noted.
EN PIN PULL-UP CURRENT
vs TEMPERATURE
3.5
1.25
3.45
1.2
EN Pin Current (µA)
EN Hysteresis Current (µA)
EN PIN HYSTERESIS CURRENT
vs TEMPERATURE
3.4
3.35
3.3
−40 −25 −10
5
20 35 50 65
Temperature (°C)
80
95
1.1
1.05
−40 −25 −10
110 125
80
95
110 125
G020
Figure 20.
EN PIN UVLO THRESHOLD
vs TEMPERATURE
SLOW-START CHARGE CURRENT
vs TEMPERATURE
2.5
ISS − Slow Start Charge Current (µA)
1.23
1.22
1.21
2.4
2.3
2.2
2.1
−40 −25 −10
-25
0
25
50
75
100
TJ - Junction Temperature - °C
Figure 21.
10
20 35 50 65
Temperature (°C)
Figure 19.
VI = 12 V
1.2
-50
5
G019
1.24
EN - UVLO Threshold - V
1.15
Submit Documentation Feedback
125
5
20 35 50 65
Temperature (°C)
80
95
110 125
G022
150
Figure 22.
Copyright © 2012, Texas Instruments Incorporated
TPS54120
www.ti.com
SBVS180C – JANUARY 2012 – REVISED JUNE 2012
TYPICAL CHARACTERISTICS (continued)
At V(PVIN) = V(VIN)= 12 V, V(LDOIN) = DC-DC_OUT = 4.1 V, V(OUT) = 3.3 V, I(OUT) = 10 mA, V(EN) = floating, COUT = 100 μF, and
CSS = CNR = 0.01µF (see Figure 28), unless otherwise noted.
PWRGD PIN THRESHOLD
vs TEMPERATURE
HIGH-SIDE CURRENT LIMIT
vs TEMPERATURE
120
ILIM(HS) − Current Limit Thresholdt (A)
7
PWRGD Threshold - % of Vref
VI = 12 V
VSENSE Rising
(overvoltage)
110
VSENSE Falling
(overvoltage)
100
VSENSE Rising
(undervoltage)
90
VSENSE Falling
(undervoltage)
80
-50
-25
0
25
50
75
100
TJ - Junction Temperature - °C
125
6
5.5
5
−40 −25 −10
5
20 35 50 65
Temperature (°C)
80
95
110 125
G024
150
Figure 23.
Figure 24.
MINIMUM CONTROLLABLE ON-TIME
vs TEMPERATURE
MINIMUM CONTROLLABLE DUTY RATIO
vs TEMPERATURE
120
6
IDC−DCOUT = 2 A
Minimum Controllable Duty Ratio (%)
Minimum Controllable On Time (ns)
6.5
110
100
90
80
−40 −25 −10
5
20 35 50 65
Temperature (°C)
80
95
RRT = 100 kΩ
IDC−DCOUT = 2 A
5
4
3
−40 −25 −10
110 125
5
G025
20 35 50 65
Temperature (°C)
Figure 25.
80
95
110 125
G026
Figure 26.
EFFICIENCY
vs LOAD CURRENT
100
VOUT = 3.3 V
90
Efficiency (%)
80
70
60
50
40
30
VIN = 15 V
VIN = 12 V
VIN = 10 V
VIN = 8 V
20
10
0
0
100 200 300 400 500 600 700 800 900 1000
Output Current (mA)
G027
Figure 27.
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
11
TPS54120
SBVS180C – JANUARY 2012 – REVISED JUNE 2012
www.ti.com
DETAILED DESCRIPTION
TYPICAL APPLICATION
Figure 28 shows a typical application diagram for the TPS54120.
DC-DC_OUT
R1
41.2 kW
L1
22 mH
CDC-DC_OUT
47 mF
CBOOT
0.1 mF
VIN
12 V
R2
10 kW
BOOT PH
LDOIN LDOEN VSENSE
R4
30.9 kW
PVIN
ON/OFF
EN
TPS54120
FB
RT/CLK
RRT
100 kW
V(OUT)
OUT
VIN
CFF
0.1 mF
COUT 3.3 V
10 mF
R5
10 kW
SS
CSS
0.01 mF
COMP
NR
GND
C2
330 pF
R3
2.2 kW
CNR
0.1 mF
C1
0.047 mF
Figure 28. Typical Application
OVERVIEW
The TPS54120 is a low-noise power supply that delivers a quiet power rail to noise-sensitive components. This
device combines a current mode-controlled, dc-dc step-down (buck) regulator and a low-noise, wide-bandwidth
low dropout (LDO) regulator to create an efficient, stable, low-noise power supply. The TPS54120 is fully
characterized for noise performance, thus allowing for easy creation of a quiet power supply. The device includes
features such as soft-start, clock synchronization, and a power-good signal, making it well suited as a power
supply for communication, test and measurement, and audio equipment applications. Both the integrated
switching regulator and LDO are fully configurable, allowing for complete design flexibility. In addition, a
simplified design procedure enables quick development of a power supply custom-suited to specific
requirements.
INPUT VOLTAGE RANGE
VIN AND POWER VIN (PVIN)
The TPS54120 allows for a variety of applications by using the VIN and PVIN pins together or separately. The
VIN pin voltage supplies the internal control circuits of the switching regulator. The PVIN pin voltage provides the
input voltage to the power converter system of the switching regulator.
If tied together, the input voltage for VIN and PVIN can range from 4.5 V to 17 V. If using the VIN separately from
PVIN, the VIN pin must be between 4.5 V and 17 V, and the PVIN pin can range from as low as 1.6 V to 17 V. A
voltage divider connected to the EN pin can adjust either input voltage UVLO appropriately. Adjusting the input
voltage UVLO on the PVIN pin helps to provide consistent power up behavior; refer to the Device Enable and
Undervoltage Lockout Adjustment section for more information.
LDO INPUT VOLTAGE (LDOIN)
The minimum input voltage that can be applied to the LDO of the TPS54120 is LDOVIN = (VOUT + VDO) or 2.2
V, whichever is greater. The maximum rated voltage into this pin should not exceed 6.5 V. This pin is designed
to be connected to the output inductor of the integrated switcher, and should be decoupled to the GND pin with a
1.0 µF ceramic capacitor.
12
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS54120
www.ti.com
SBVS180C – JANUARY 2012 – REVISED JUNE 2012
ADJUSTING THE OUTPUT VOLTAGE
The output voltage of both the switcher and the LDO are adjustable. They are set with a resistor divider from the
output voltage to the feedback sensing pin. Use 1%-tolerance or better divider resistors for best accuracy.
The values of the LDO feedback resistors can be calculated using Equation 1:
V(OUT) = (R4 + R5) Vref / R5
Where:
Vref = 0.8 V
R4 = The resistor from the output to the FB pin of the LDO.
R5 = The resistor from the FB pin to ground of the LDO.
(1)
The values of the switching regulator feedback resistors can be calculated using Equation 2:
DC-DC_OUT = (R1 + R2) Vref / R2
Where:
Vref = 0.8 V
R1 = The resistor from the switcher output at the inductor to the VSENSE pin of the switching regulator.
R2 = The resistor from the VSENSE pin to ground switching regulator.
(2)
To improve efficiency at light loads, consider using larger-value resistors. Larger-value resistors may increase the
noise sensitivity at the VSENSE and FB pins and error from the VSENSE and FB pin input currents. Using a
value of 10 kΩ for R2 and R5 provides a good trade-off between these two issues.
POWER CONVERSION EFFICIENCY VERSUS OUTPUT NOISE
The configuration of the TPS54120 consists of a switching regulator followed by an LDO. The ability of the LDO
to reject the noise created by the switching regulator and not pass it to the LDO output is determined by the
power supply rejection (PSR) of the LDO. The PSR of an LDO depends on the LDO input to LDO output voltage
difference. The higher the voltage difference, the better the LDO ability to reject noise at its input. The LDO in the
TPS54120 has been designed to provide high, wide-bandwidth PSR with a minimum of input to output voltage
differential. At 1 A for the highest PSR performance, the input-to-output voltage differential should be set to 0.8 V
or greater.
The LDO voltage differential is also a primary contributor to the overall power loss in the TPS54120. The LDO
input and output voltage differentials contribution to the power loss is defined as the output current times the
input-to-output voltage differential, as shown in Equation 3:
Power Loss from the LDO = I(OUT) × (V(LDOIN) – V(OUT))
(3)
Therefore, for a 0.8-V drop at 1 A, this loss is 0.8 W. The impact of the power loss can be reduced by lowering
VDO; however, the PSR of the LDO may be impacted. In the Typical Characteristics section, Figure 6 and
Figure 7 show the trade-off between PSR and VDO for various output current levels and frequencies. For currents
less than 500mA, a VDO of 0.5 V does not have significant impact on PSR performance and provides a
substantial improvement to the power loss from the VDO.
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
13
TPS54120
SBVS180C – JANUARY 2012 – REVISED JUNE 2012
www.ti.com
BOOTSTRAP VOLTAGE AND LOW DROPOUT OPERATION
The TPS54120 has an integrated boot regulator, and requires a small ceramic capacitor between the BOOT and
PH pins to provide the gate drive voltage for the high-side MOSFET. The boot capacitor is charged when the
BOOT pin voltage is less than VIN and the (BOOT – PH) voltage is below regulation. The value of this ceramic
capacitor should be 0.1 μF. A ceramic capacitor with an X7R- or X5R-grade dielectric with a voltage rating of 10
V or higher is recommended because of the stable characteristics over temperature and voltage.
To improve dropout, the device is designed to operate at 100% duty cycle, as long as the BOOT to PH pin
voltage is greater than the (BOOT – PH) UVLO threshold (typically 2.1 V). When the voltage between BOOT and
PH drops below the (BOOT – PH) UVLO threshold, the high-side MOSFET is turned off and the low-side
MOSFET is turned on allowing the boot capacitor to be recharged. In applications with split input voltage rails,
100% duty-cycle operation can be achieved as long as (VIN – PVIN) > 4V and (V(BOOT) – V(PH)) > 2.1V; the
UVLO threshold for the BOOT pin.
NOTE
A boot resistor in series with the boot capacitor should never be used on the TPS54120.
OUTPUT OVERVOLTAGE PROTECTION (OVP)
The TPS54120 has an overvoltage protection (OVP) circuit on the switcher output to minimize overshoots on the
switcher output. This also protects the input of the LDO from experiencing overshoot above its rated values.
CAUTION
Any voltage above the absolute maximum rated input voltage into the LDOIN pin can
damage the device.
When the power-supply output is overloaded, the error amplifier compares the actual output voltage to the
internal reference voltage. If the VSENSE pin voltage is lower than the internal reference voltage for a
considerable amount of time, the output of the error amplifier demands maximum output current. Once the
condition is removed, the regulator output rises and the error amplifier output transitions to the steady-state
voltage. In some applications with small output capacitance, the dc-dc output voltage can respond faster than the
error amplifier. This leads to the possibility of a switcher output overshoot.
The OVP feature minimizes overshoot by comparing the VSENSE pin voltage to the OVP threshold. If the
VSENSE pin voltage is greater than the OVP threshold, the high-side MOSFET is turned off, preventing current
from flowing to the output and minimizing output overshoot. When the VSENSE voltage drops below the OVP
threshold, the high-side MOSFET is allowed to turn on at the next clock cycle.
14
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS54120
www.ti.com
SBVS180C – JANUARY 2012 – REVISED JUNE 2012
OVERCURRENT PROTECTION
SWITCHER OVERCURRENT PROTECTION
The integrated switcher of the TPS54120 is protected from overcurrent conditions by using cycle-by-cycle current
limiting on both MOSFETs, the low-side and the high-side.
HIGH-SIDE MOSFET OVERCURRENT PROTECTION
High-side MOSFET overcurrent protection is achieved by an internal current comparator that monitors the current
in the high-side MOSFET on a cycle-by-cycle basis. If this current exceeds the current limit threshold, the highside MOSFET is turned off for the remainder of that switching cycle. During normal operation, the device
implements current mode control. Current mode control uses the COMP pin voltage to control the turn-off of the
high-side MOSFET and the turn-on of the low-side MOSFET on a cycle-by-cycle basis. Each cycle, the switch
current and the current reference generated by the COMP pin voltage are compared. When the peak switch
current intersects the current reference, the high-side switch is turned off.
LOW-SIDE MOSFET OVERCURRENT PROTECTION
While the low-side MOSFET is turned on, its conduction current is monitored by the internal circuitry. During
normal operation, the low-side MOSFET sources current to the load. At the end of every clock cycle, the low-side
MOSFET sourcing current is compared to the internally set low-side sourcing current limit. If the low-side
sourcing current is exceeded, the high-side MOSFET is not turned on and the low-side MOSFET stays on for the
next cycle. The high-side MOSFET is turned on again when the low-side current falls below the low-side sourcing
current limit at the start of a cycle. The low-side MOSFET may also sink current from the load. If the low-side
sinking current limit is exceeded, the low-side MOSFET is turned off immediately for the rest of that clock cycle.
In this scenario, both MOSFETs remain off until the start of the next cycle.
If an output overload condition (as measured by the COMP pin voltage) has lasted longer than the current-limit
protection mode wait time (programmed for 512 switching cycles), the device shuts down and restarts after the
current-limit protection mode time (set for 16384 cycles). The current-limit protection mode helps to reduce
device power dissipation under severe overcurrent conditions
LDO INTERNAL CURRENT LIMIT
In addition to the switcher overcurrent protection, the TPS54120 has an internal current limit on the integrated
LDO. The LDO internal current limit helps protect the LDO during fault conditions. During current limit, the output
sources a fixed amount of current that is largely independent of output voltage. For reliable operation, the device
should not be operated in a current-limit state for extended periods of time. The PMOS pass element in the
integrated LDO has a built-in body diode that conducts current when the voltage at OUT exceeds the voltage at
LDOIN. This current is not limited, so if extended reverse-voltage operation is anticipated, external limiting may
be required.
THERMAL INFORMATION
The internal protection circuitry of the device has been designed to protect against overload conditions. However,
this circuitry was not intended to replace proper heat sinking. Continuously running the device into thermal
shutdown degrades device reliability. The TPS54120 has thermal protection for both the switcher and the LDO,
and they operate independently of each other.
THERMAL PROTECTION OF THE SWITCHER
The internal thermal-shutdown circuitry of the switcher forces the device to stop switching if the junction
temperature exceeds +175°C, typically. The device turns back on when the junction temperature drops below
+165°C typically.
THERMAL PROTECTION OF THE LDO
Thermal protection of the integrated LDO disables the output of the TPS54120 when the junction temperature
rises to approximately +160°C, allowing the device to cool. When the junction temperature cools to approximately
+140°C, the output circuitry is enabled. Depending on power dissipation, thermal resistance, and ambient
temperature, the thermal protection circuit may cycle on and off. This cycling limits the dissipation of the
regulator, protecting it from damage because of overheating.
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
15
TPS54120
SBVS180C – JANUARY 2012 – REVISED JUNE 2012
www.ti.com
ADJUSTABLE SWITCHING FREQUENCY AND SYNCHRONIZATION (RT/CLK)
The RT/CLK pin can be used to set the switching frequency of the device in two modes: RT and CLK.
RT MODE
A resistor, R(RT), is connected between the RT/CLK pin and GND. The switching frequency of the device is
adjustable from 200 kHz to 1200 kHz by using a maximum of 240 kΩ and minimum of 40.2 kΩ, respectively. To
determine the value of the RT resistor for a given switching frequency (fSW), use Equation 4 or the curve in
Figure 1:
RRT (kΩ) = 60281 fSW–1.033 (kHz)
(4)
250
RRT (kΩ)
200
150
100
50
0
200
300
400
500
600
700
800
900
1000
1100
1200
fSW (kHz)
Figure 29. RT Set Resistor vs Switching Frequency
CLK MODE
In CLK mode, an external clock is connected directly to the RT/CLK pin. The device is synchronized to the
external clock frequency with a phase-locked loop (PLL). CLK mode overrides RT mode. The device is able to
automatically detect the required mode and switch from RT mode to CLK mode. An internal PLL has been
implemented to allow synchronization between 200 kHz and 1.2 MHz, and to easily switch from RT mode to CLK
mode. To implement the synchronization feature, connect a square-wave clock signal to the RT/CLK pin with a
duty cycle between 20% to 80%. The clock signal amplitude must transition less than 0.8 V and greater than 2.0
V. The start of the switching cycle is synchronized to the falling edge of RT/CLK pin. In applications where both
RT mode and CLK mode are required, the device can be configured to have both RT resistor and external clock
connected at the same time to RT/CLK pin. Before the external clock is present, the device works in RT mode
and the switching frequency is set by RT resistor. When the external clock is present, CLK mode overrides RT
mode and ignores the RT resistor. The first time the SYNC pin is pulled above the RT/CLK high threshold (2.0
V), the device switches from RT mode to CLK mode and the RT/CLK pin becomes high impedance as the PLL
starts to lock on to the frequency of the external clock. It is not recommended to switch from the CLK mode back
to the RT mode because the internal switching frequency drops to 100 kHz first before returning to the switching
frequency set by RT resistor.
16
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS54120
www.ti.com
SBVS180C – JANUARY 2012 – REVISED JUNE 2012
START-UP TIME
SOFT-START OF THE SWITCHER
The rate at which the output voltage of the switcher rises up to the full operational level during the start-up phase
is controlled through the SS pin. A capacitor, CSS, is connected between the SS pin and the IC ground. The size
of the capacitor determines the soft-start ramp-up time (tss, 10% to 90%), as shown in Equation 5:
tSS (ms) = C(SS) (nF) Vref (V)) / ISS (µA)
(5)
The device has an internal pull-up current source of 2.3 µA = Iss that charges the external soft-start capacitor,
CSS. The voltage reference, Vref, for this device is 0.8 V. Thus, by sourcing a constant current onto the capacitor,
the device linearly ramps up the voltage on the SS pin, which corresponds to the voltage on the FB pin and thus,
the output voltage of the switcher.
If the input UVLO is triggered, the EN pin is pulled below 1.21 V, or a thermal shutdown event occurs, then the
device stops switching and enters low-current operation. At the subsequent power-up, when the shutdown
condition is removed, the device does not start switching until it has discharged the SS/TR pin to ground,
ensuring proper soft-start behavior.
NR SOFT-START TIME AND LDO START-UP
The NR capacitors main purpose is to filter the noise from the LDO bandgap, and thereby reduce the LDO output
noise. However, these capacitors also affect the start-up time of the LDO. The TPS54120 has a quick-start circuit
to quickly charge C(NR), if it is present; see the Functional Block Diagram. At start-up, this quick-start switch is
closed, creating only 33 kΩ of resistance between the band gap reference and the NR pin. The quick-start switch
opens approximately 2 ms after any device enabling event, and the resistance between the band gap reference
and the NR pin becomes higher in value (approximately 250 kΩ) to form a very good low-pass (RC) filter. This
low-pass filter achieves very good noise reduction for the reference voltage.
Inrush current can be a problem in many applications. The 33-kΩ resistance during the start-up period is
intentionally added to slow down the reference voltage ramp up, thus reducing the inrush current. For example,
the capacitance of connecting the recommended C(NR) value of 0.01 μF along with the 33-kΩ resistance causes
an approximately 1-ms RC delay. Start-up time for the LDO with other C(NR) values can be determined by using
Figure 13 or calculated as shown in Equation 6:
tSTR(s) = 76000 × C(NR) (F)
(6)
Although the noise reduction effect is nearly saturated at 0.01 μF, connecting a C(NR) value greater than 0.01 μF
can help reduce noise slightly more; however, start-up time may become longer because the quick-start switch
opens after approximately 2 ms. That is, if CNR is not fully charged during this 2-ms period, C(NR) finishes
charging through a higher resistance of 250 kΩ, and takes much longer to fully charge. Note that a low leakage
C(NR) should be used; most ceramic capacitors are suitable.
POWER GOOD (PWRGD)
The PWRGD pin is an open drain output. Once the VSENSE pin is between 94% and 106% of the internal
voltage reference, the PWRGD pin pull-down is de-asserted and the pin floats. It is recommended to place a 10kΩ to 100-kΩ pull-up resistor to a voltage source that is less than or equal to 5.5 V. The PWRGD is in a defined
state after the VIN input voltage is greater than 1 V, but with reduced current-sinking capability. The PWRGD pin
achieves full current-sinking capability after the VIN input voltage is greater than 4.5 V.
The PWRGD pin is pulled low when VSENSE is lower than 91% or greater than 109% of the nominal internal
reference voltage. The PWRGD is also pulled low if the input UVLO or thermal shutdown are asserted, the EN
pin is pulled low, or the SS/TR pin is less than 1.2 V, typically.
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
17
TPS54120
SBVS180C – JANUARY 2012 – REVISED JUNE 2012
www.ti.com
DEVICE ENABLE AND UNDERVOLTAGE LOCKOUT ADJUSTMENT
SWITCHER ENABLE AND UNDERVOLTAGE LOCKOUT
The EN pin is used to turn the switcher on and off. When the EN pin voltage exceeds the threshold voltage, the
device begins operating. If the EN pin voltage is pulled below the threshold voltage, the regulator stops switching
and enters a low IQ state.
The EN pin has an internal pull-up current source; float or drive the EN pin to enable the device. If an application
requires control of the EN pin, use an open-drain or open-collector output logic to interface with the pin.
The TPS54120 implements internal UVLO circuitry on the VIN pin. The device is disabled when the VIN pin
voltage falls below the internal VIN UVLO threshold. The internal VIN UVLO threshold has a hysteresis of 150
mV.
If an application requires either a higher UVLO threshold on the VIN pin, or a secondary UVLO on the PVIN pin
in split-rail applications, then the EN pin can be configured as shown in Figure 30, Figure 31, or Figure 32. When
using the external UVLO function, it is recommended to set the hysteresis to be greater than 500 mV.
VIN
ip
ih
R1
R2
EN
Figure 30. Adjustable VIN Under Voltage Lock Out
PVIN
ip
ih
R1
R2
EN
Figure 31. Adjustable PVIN Under Voltage Lock Out, VIN ≥ 4.5V
PVIN
VIN
ip
ih
R1
R2
EN
Figure 32. Adjustable VIN and PVIN Under Voltage Lock Out
18
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS54120
www.ti.com
SBVS180C – JANUARY 2012 – REVISED JUNE 2012
The EN pin has a small pull-up current (Ip) that sets the state of the pin to enable (default) when no external
components are connected. The pull-up current is also used to control the voltage hysteresis for the UVLO
function because it increases by Ih when the EN pin crosses the enable threshold. The UVLO thresholds can be
calculated using Equation 7 and Equation 8.
æV
ö
VSTART ç ENFALLING ÷ - VSTOP
è VENRISING ø
R1 =
æ V
ö
Ip ç1 - ENFALLING ÷ + Ih
VENRISING ø
è
(7)
R2 =
R1´ VENFALLING
VSTOP - VENFALLING + R1(Ip + Ih )
(8)
LDO ENABLE AND UNDERVOLTAGE LOCKOUT
The LDO enable pin (LDOEN) is active-high and compatible with standard and low-voltage, TTL-CMOS levels.
When shutdown capability is not required, EN can be connected to IN.
The LDO also has a fixed UVLO to keep the output shut off until the LDO internal circuitry is working properly.
The LDO UVLO circuit has a deglitch feature that ignores undershoot transients on the LDO input if they are less
than 50 µs in duration.
SEQUENCING
The TPS54120 is easy to use and suited for applications that require tracking and sequencing. It has a built-in
power good function to indicate the status of the device, a soft-start circuit to control the output voltage slope
during start-up, noise reduction with start-up time for the LDO, and an enable function for independently
controlling the start-up of both the LDO and the switcher. Each of these functions is useful for tracking and
sequencing applications. See Application Report SLVA497, TPS54120 Sequencing and Tracking, for more
details regarding the sequencing application setup of the TPS54120.
SWITCHER PWM CONTROL AND CONTINUOUS CURRENT MODE OPERATION (CCM)
The integrated switcher of the TPS54120 uses adjustable, fixed-frequency, peak-current mode control. The
output voltage is compared through external resistors on the VSENSE pin to an internal voltage reference by an
error amplifier that drives the COMP pin. An internal oscillator turns on the high-side power switch. The error
amplifier output is converted into a current reference that is compared to the high-side power switch current.
When the power-switch current reaches the current reference generated by the COMP voltage level, the highside power switch is turned off and the low-side power switch is turned on. The device normally works in
continuous conduction mode (CCM) under all load conditions.
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
19
TPS54120
SBVS180C – JANUARY 2012 – REVISED JUNE 2012
www.ti.com
SMALL-SIGNAL MODEL FOR LOOP RESPONSE
Figure 33 shows an equivalent model for the device control loop. This model can be run in a circuit simulation
program to check frequency and transient responses. The error amplifier is a transconductance amplifier with a
gM of 1300 mA/V, and can be modeled using an ideal voltage-controlled current source. Resistor Roea (2.38
MΩ) and capacitor Coea (20.7 pF) model the open-loop gain and frequency response of thSLVA497e error
amplifier.
PH
VOUT
Power Stage
12 A/V
a
b
c
0.8 V
R4 Coea
C6
R8
RESR
VSENSE
CO
COMP
C4
Roea
gm
1300 mA/V
RL
R9
Figure 33. Small-Signal Model for Loop Response
The 1-mV ac voltage source between nodes a and b effectively breaks the control loop for the frequencyresponse measurements. Plotting a/c and c/b show the small-signal responses of the power stage and frequency
compensation, respectively. Plotting a/b shows the small-signal response of the overall loop. The dynamic loop
response can be checked by replacing RL with a current source that has the appropriate load step amplitude and
step rate in a time-domain analysis. Refer to Application Report SLVA503, Understanding Compensation
Network for the TPS54120, for a more detailed treatment of the small-signal model and compensation for the
TPS54120.
20
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS54120
www.ti.com
SBVS180C – JANUARY 2012 – REVISED JUNE 2012
APPLICATION INFORMATION
DESIGN METHODOLOGY
The TPS54120 has a low-noise output voltage range from 0.8 V to 6.0 V with an output current of up to 1 A. To
simplify design efforts using the TPS54120, typical designs for common applications are listed in Table 1
according to the typical schematic diagram shown in Figure 34. For more details about designing with the
TPS54120, refer to Application Report SLVA506, Design Procedure for the TPS54120, and SLVC411, the
TPS54120 Design Tool Calculator.
The TPS54120 can also be configured to provide two separate power rails: one from the switching regulator and
one from the LDO. For more information on how to create a dual-rail power supply from the TPS54120, refer to
Application Report SLVA502, Design Guidelines for TPS54120 as a 3-A Switcher and 1-A Switcher Plus LDO.
LDO OUT
COUT
C_LDO_IN
PWPD
24
LDOIN
25
CFF
OUT 1
2 OUT
LDOIN 23
3 FB
LDOEN 21
5 NC
RRT
NC 20
U
TPS54120
6 RT/CLK
7 PGND
CIN
PH 17
9 PVIN
PH 16
10 PVIN
EN 15
11 VIN
SS
VSENSE
CBOOT
BOOT 18
8 PGND
12
VIN
PWRGD 19
L1
14
13 COMP
R5
CNR
NR 22
4 GND
C11
SENSE
SENSE
R3
PGND
DC-DC_OUT
C_DC-DC_OUT
R4
AGND
C1
R1
R2
CSS
C2
Figure 34. Application Circuit
Figure 34 shows a typical application diagram for the TPS54120. The first step in the design process is to select
the switching frequency for the regulator. Higher switching frequencies may produce a smaller solution size using
lower-valued inductors and smaller output capacitors compared to a power supply that switches at a lower
frequency. However, higher switching frequencies causes additional switching losses that negatively impact
converter efficiency and thermal performance.
After a switching frequency is determined, the inductor and output capacitor values of the switcher are selected.
These two component values are related to each other and they depend on the input and output voltages of the
switcher, as well as the current rating. Choosing a high inductor-ripple current also impacts the selection of the
output capacitor because the output capacitor must have a ripple current rating equal to or greater than the
inductor ripple current.
The TPS54120 requires a high-quality ceramic, type X5R or X7R, input decoupling capacitor of 4.7 μF on each
input voltage rail. In some applications, additional bulk capacitance may also be required for the PVIN input. The
voltage rating of the input capacitor must be greater than the maximum input voltage.
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
21
TPS54120
SBVS180C – JANUARY 2012 – REVISED JUNE 2012
www.ti.com
The internal LDO of the TPS54120 is designed to be stable with standard ceramic output capacitors with values
of 4.7 μF or larger; higher values are recommended for better noise performance.
A 0.1-μF ceramic capacitor must be connected between the BOOT and PH pins for proper operation. It is
recommended to use a ceramic capacitor with X5R or better grade dielectric. The capacitor should have a 10-V
or higher voltage rating.
The output voltage of both the switcher and the LDO are adjustable using an external-resistor feedback network.
Also, both the LDO and the switcher have a soft-start function that can be adjusted externally using the CSS and
CNR capacitors, as shown in Figure 34.
There are several industry techniques used to compensate dc-dc regulators; refer to Application Report
SLVA503 for more details about different compensation networks for the TPS54120.
SIMPLIFIED DESIGN METHODOLOGY
The TPS54120 has a low-noise output voltage range of 0.8 V to 6.0 V with an output current of up to 1 A. To
simplify design efforts using the TPS54120, the typical designs for common applications are listed in Table 1. For
designs using ceramic output capacitors, proper derating of ceramic output capacitance is recommended when
doing the stability analysis because the actual ceramic capacitance drops considerably from the nominal value
when the applied voltage increases. To execute a complete application design, refer to Application Report
SLVA506, Design Procedures for the TPS54120.
Table 1. Simplified Design Table
DC-DC_
OUT
(V)
VOUT
(V)
IOUT
(max)
(A)
fSW
(kHz)
5
3
7
2.5
1.8
1.0
1.8
0.25
8
2.5
1.8
12
3.7
12
VIN
(V)
C2
(pF)
COUT
(µF)
C11
(pF)
CFF
(µF)
RMS NOISE
100 Hz
TO
100 kHz
AT 100 mA
(µVrms)
0.047
330
100
270
0.1
7.32
56.35
0.220
1000
100
499
0.1
7.83
67.35
100
0.047
330
100
330
0.1
7.22
66.25
10
100
0.047
330
100
200
0.1
8.27
75.42
30.9
10
100
0.100
330
100
180
0.1
8.3
73.38
2.2
30.9
10
100
0.047
330
100
180
0.1
7.52
74.67
10
2.94
52.3
10
100
0.047
330
100
120
0.1
10.61
80.95
64.9
10
7.15
52.3
10
47.5
0.033
33
100
51
0.1
10.71
73.33
47
64.9
10
3.16
59.0
10
100
0.047
330
100
110
0.1
11.47
83.91
27
47
64.9
10
3.16
52.3
10
100
0.047
330
100
110
0.1
10.69
74.59
130
47
64.9
10
3.16
52.3
10
100
0.220
330
100
110
0.1
10.81
76.84
L1
(µH)
CDC-DC_OUT
(µF)
R1
(kΩ)
R2
(kΩ)
R3
(kΩ)
R4
(kΩ)
R5
(kΩ)
RRT
(kΩ)
C1
(µF)
480
18
47
27.4
300
100
47
21.5
10
1.58
12.4
10
100
10
0.887
12.4
10
165
1.0
480
15
47
21.5
10
1.33
12.4
10
3.0
1.0
480
20
47
36.5
10
1.96
27.4
4.1
3.3
0.5
480
43
47
41.2
10
2.2
12
4.1
3.3
1.0
480
22
47
41.2
10
12
5.5
5.0
1.0
480
27
47
59.0
12
6
5.0
0.5
1000
27
47
12
6
5.5
1.0
480
27
16
6
5.0
1.0
480
17
6
5.0
0.2
480
22
Submit Documentation Feedback
EFFICIENCY
(%)
Copyright © 2012, Texas Instruments Incorporated
TPS54120
www.ti.com
SBVS180C – JANUARY 2012 – REVISED JUNE 2012
PCB LAYOUT GUIDELINES
PACKAGE MOUNTING
Solder pad footprint recommendations for the TPS54120 are available at the end of this product datasheet and
at www.ti.com.
BOARD LAYOUT RECOMMENDATIONS FOR HIGH-PSR AND LOW-NOISE PERFORMANCE
Correct printed circuit board (PCB) layout is a critical portion of good power-supply design and is a particularly
important for the high PSR and low-noise performance of the TPS54120. The following general guidelines are
provided; for a more detailed description, refer to the TPS54120EVM User Guide, SLVU641.
• The inductor, the boot capacitor, and the output cap of the dc-dc converter should be placed on layers of the
board that help minimize the spread of the switching noise into the LDO area on the board, such as the
bottom layer.
• The boot cap and inductor L1 should be connected as close as possible to the PH pin to reduce parasitic
inductance of long traces.
• To help shield the compensation components, the soft-start capacitors, CLK/RT resistor, and dc-dc feedback
resistors from noise, these components should be grounded to a power ground that is shielded from the highcurrent ground plane. This shielding can be achieved by using a separate trace to the PGND pin.
• The RT/CLK pin is sensitive to noise, so the RT resistor should be located as close as possible to the device
and routed with a short connection.
• The noise-reduction capacitor should be placed as close as possible to the device to avoid noise pickup into
the LDO reference.
• The ground planes on the input and the output should be isolated from each other and connected through a
separate trace route that parallels the power-loop routing from the dc-dc output to the LDO input.
• The low-noise analog ground of the LDO circuits (such as the voltage set point divider, the LDO input, and
output caps) should be terminated to ground using a wide ground trace separate from the power ground
plane.
• The LDO input capacitor and output capacitor should be as close to the device as possible.
• The VIN and PVIN pins must be bypassed to ground using a low ESR ceramic capacitor with X5R or X7R
dielectric and placed as close as possible to the VIN, PVIN, and PGND pins.
• For operation at full-rated load, the top-side ground area together with the internal ground plane must provide
adequate heat dissipation.
• PCB conductor planes should be minimized to prevent excessive capacitive coupling.
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
23
TPS54120
SBVS180C – JANUARY 2012 – REVISED JUNE 2012
www.ti.com
REVISION HISTORY
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision B (March 2012) to Revision C
Page
•
Added capacitor to Figure 28 .............................................................................................................................................. 12
•
Changed Equation 3 ........................................................................................................................................................... 13
•
Added two new columns to Table 1 .................................................................................................................................... 22
Changes from Revision A (January 2012) to Revision B
•
Deleted device name from Figure 30, Figure 31, and Figure 32 (typo) ............................................................................. 18
Changes from Original (January 2012) to Revision A
•
24
Page
Page
Changed from product preview to production data ............................................................................................................... 1
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
PACKAGE OPTION ADDENDUM
www.ti.com
20-Jun-2012
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
TPS54120RGYR
ACTIVE
VQFN
RGY
24
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
TPS54120RGYT
ACTIVE
VQFN
RGY
24
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Samples
(Requires Login)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
20-Jun-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
TPS54120RGYR
VQFN
RGY
24
3000
330.0
12.4
3.8
5.8
1.2
8.0
12.0
Q1
TPS54120RGYT
VQFN
RGY
24
250
180.0
12.4
3.8
5.8
1.2
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
20-Jun-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TPS54120RGYR
VQFN
RGY
24
3000
346.0
346.0
29.0
TPS54120RGYT
VQFN
RGY
24
250
210.0
185.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
Wireless Connectivity
www.ti.com/wirelessconnectivity
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated