PRELIMINARY ML2731 PA Bias Controller GENERAL DESCRIPTION FEATURES n Sets PA current and power output using a bias control The ML2731 is a power amplifier (PA) bias controller with support circuits for a typical radio transceiver. The IC integrates a PA bias controller, a PA DC switch, a crystal oscillator circuit, a negative voltage generator and two voltage regulators. It can be used with GaAs FETs and silicon bipolar devices. loop n Integrates a PA DC supply switch n Prevents PA power-on if negative voltage is not present n Integrates all circuits needed for supporting a crystal oscillator with 10MHz to 40MHz frequency range n Incorporates a fast starting, high switching frequency, Micro Linear’s ML2731, along with the ML2712 and the ML2713, form a complete transceiver solution for the 2.4 GHz IEEE802.11 communication standard, as well as other wireless ISM communication products. negative voltage generator requiring only small ceramic capacitors n Contains voltage regulators for an oscillator, a negative In addition to supporting Micro Linear’s transceiver chip set, the ML2731 can stand alone as: A compact bias voltage controller voltage generator and a 50mA 3.0V LDO output n Requires less than 1mA of current when powered down n Supply voltage ranges from 3.3V to 5.5V A compact negative voltage generator A compact crystal oscillator APPLICATIONS n Cellular and Cordless Radios n WLAN Radios n Radios with GaAs FET Power Amplifiers n Fixed and Mobile radio transceivers SIMPLIFIED BLOCK DIAGRAM ML2731 VPA PAEN PA on/off switch and current sense ICON VBIAS Bias Control NEGEN VNEG C1 C2 Negative voltage generator Crystal Oscillator XIN Crystal XOUT Voltage Regulator Sine & square wave drivers PDN REGO SINO GaAs FET Power Amplifier PRELIMINARY DATASHEET CLKO ML2712 ML2713 Radio January, 2000 Baseband Controller (e.g. MSM7730B) PRELIMINARY ML2731 TABLE OF CONTENTS General Description ................................................................................................................................................... 1 Simplified Block Diagram .......................................................................................................................................... 1 Features ...................................................................................................................................................................... 1 Applications ............................................................................................................................................................... 1 Block Diagram ........................................................................................................................................................... 3 Pin Configuration ....................................................................................................................................................... 4 Pin Descriptions ......................................................................................................................................................... 4 Functional Description ............................................................................................................................................... 6 Introduction .............................................................................................................................................................. 6 External Interfaces ................................................................................................................................................... 6 Mode Control ........................................................................................................................................................... 6 Description Of Operation ........................................................................................................................................... 6 Crystal Oscillator ..................................................................................................................................................... 7 Negative Voltage Generator ..................................................................................................................................... 7 Absolute Maximum Ratings ........................................................................................................................................ 11 Electrical Tables ......................................................................................................................................................... 11 Electrical Characteristics ............................................................................................................................................ 11 Operating Conditions ................................................................................................................................................. 11 Physical Dimensions .................................................................................................................................................. 12 Ordering Information .................................................................................................................................................. 12 WARRANTY Micro Linear makes no representations or warranties with respect to the accuracy, utility, or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice. No license, express or implied, by estoppel or otherwise, to any patents or other intellectual property rights is granted by this document. The circuits contained in this document are offered as possible applications only. Particular uses or applications may invalidate some of the specifications and/or product descriptions contained herein. The customer is urged to perform its own engineering review before deciding on a particular application. Micro Linear assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of Micro Linear products including liability or warranties relating to merchantability, fitness for a particular purpose, or infringement of any intellectual property right. Micro Linear products are not designed for use in medical, life saving, or life sustaining applications. © 2000. Micro Linear is a registered trademark of Micro Linear Corporation. All other trademarks are the property of their respective owners. Products described herein may be covered by one or more of the following U.S. patents: 4,897,611; 4,964,026; 5,027,116; 5,281,862; 5,283,483; 5,418,502; 5,508,570; 5,510,727; 5,523,940; 5,546,017; 5,559,470; 5,565,761; 5,592,128; 5,594,376; 5,652,479; 5,661,427; 5,663,874; 5,672,959; 5,689,167; 5,714,897; 5,717,798; 5,742,151; 5,747,977; 5,754,012; 5,757,174; 5,767,653; 5,777,514; 5,793,168; 5,798,635; 5,804,950; 5,808,455; 5,811,999; 5,818,207; 5,818,669; 5,825,165; 5,825,223; 5,838,723; 5.844,378; 5,844,941. Japan: 2,598,946; 2,619,299; 2,704,176; 2,821,714. Other patents are pending. 2 PRELIMINARY DATASHEET January, 2000 ML2731 PRELIMINARY BLOCK DIAGRAM SINO CLKO VCC 1 8 2 BUFFER AND DRIVERS 10 VNEG XIN 15 XOUT 16 OSCILLATOR AND DIVIDER NEGATIVE VOLTAGE GENERATOR 12 C1 11 C2 PAEN NEGEN 6 7 PDN 14 REGO 3 REFERENCE GENERATOR AND LOGIC REGULATOR 5 ICON 4 VBIAS BIAS CONTROL SWITCH AND CURRENT SENSE 13 VPA 9 GND January, 2000 PRELIMINARY DATASHEET 3 ML2731 PRELIMINARY PIN CONFIGURATION ML2731 16-Pin TSSOP (T16) SINO 1 16 XOUT VCC 2 15 XIN REGO 3 14 PDN VBIAS 4 13 VPA ICON 5 12 C1 PAEN 6 11 C2 NEGEN 7 10 VNEG CLKO 8 9 GND TOP VIEW PIN DESCRIPTIONS 4 Pin # Signal Name I/O Description 1 SINO O (ANLG) Sine wave output. This pin is a low impedance output capable of driving a 2kW load. The signal is sourced with either a crystal interfaced with on-chip components through XOIN (pin 15) and XOUT (pin 16) or with a completely external oscillator through pin 15. Taking PDN (pin 14) high switches off output 2 VCC O (ANLG) DC power supply 3 REGO O (ANLG) IC regulator output. This is the output from the on IC regulator. It is disabled in the SLEEP mode of operation and enabled in all other modes. The nominal output voltage is 2.9 V and it has a low impedance output which can source up to 50mA 4 VBIAS O (ANLG) PA bias voltage output. This output has limited drive capability of 3mA and is intended to drive the gate or bias of the PA 5 ICON I (ANLG) Reference current input. Used by the PA bias control loop to set the PA current level. This input appears as a virtual ground 6 PAEN I (CMOS) PA Enable. Transitions from high to low on this pin activate the PA current ramp up function, switch the PA voltage supply switch on and enable the PA bias control loop. Transitions from low to high activate the PA current ramp down function and switch the PA voltage supply off 7 NEGEN I (CMOS) Negative Voltage Enable. In conjunction with PDN and PAEN, NEGEN controls the operational mode of the IC and enables the negative voltage generator circuits 8 CLKO I (CMOS) Clock output. The frequency is set with either a crystal interfaced with on-chip components through XOIN (pin 15) and XOUT (pin 16) or with a completely external oscillator through pin 15. CLKO switches off when device goes into SLEEP mode when PDN is taken high 9 GND GND 10 VNEG O (ANLG) Negative regulator output. This pin is one of the outputs of the negative switching regulator. A capacitor connected serves as a current reservoir. Typically a 100nF capacitor is connected between pin 10 and GND 11 C2 O (ANLG) Noise Shunt. Negative voltage generator capacitor connection. This output of the negative switching regulator shunts regulator noise to ground using a 100nF bypass capacitor Ground PRELIMINARY DATASHEET January, 2000 ML2731 PRELIMINARY PIN DESCRIPTIONS (continued) Pin # Signal Name I/O Description 12 C1 O (ANLG) Noise Shunt. Negative voltage generator bypass capacitor connection. Typically a 100nF capacitor is connected between pin C1 and C2 13 VPA O (ANLG) PA supply. This is the positive supply for the PA. It is switched by PAEN in conjunction with PDN and NEGEN 14 PDN I (ANLG) Power down control. Disables all circuits and reduces power consumption to less than 1mA 15 XIN I (ANLG) Crystal or oscillator input. This high input impedance is connected to either an oscillator circuit or to a crystal 16 XOUT I (ANLG) Crystal-tank connection. This low impedance output drives the crystal tank circuit January, 2000 PRELIMINARY DATASHEET 5 ML2731 PRELIMINARY FUNCTIONAL DESCRIPTION INTRODUCTION DESCRIPTION OF OPERATION EXTERNAL INTERFACES Voltage Regulator The ML2731 has 3 logic inputs: PAEN, NEGEN and PDN. These control lines are used to select the mode of operation to be either SLEEP, STANDBY, PRETX or TRANSMIT. (See Table 1) PDN NEGEN PAEN Mode 1 X X SLEEP 0 1 X STANDBY 0 0 1 PRETX 0 0 0 TRANSMIT The ML2731 integrates two low noise voltage regulators. The first regulator internally powers the crystal oscillator support circuit, negative voltage generator support circuit and other on chip circuits. The second regulator output (REGO) powers external circuits. (See Figure 1) It has a nominal voltage output of 2.9V and sources up to 50mA of current. The low noise output of this regulator makes it suitable for supplying voltage to sensitive components such as final frequency VCO’s. The regulator output is disabled in the SLEEP mode and is enabled in all other modes. 2.92 Table 1. Circuit Enable Logic MODE CONTROL Mode Functions The function of the ML2731 in each mode of operation: VOLTAGE (V) 2.90 2.88 2.86 SLEEP All the circuits are disabled. Current drain is typically less than 1mA. STANDBY 2.84 0 20 30 40 50 CURRENT (mA) Figure 1. Regulator Ouput Voltage vs. Load Current (REGO) Oscillator circuits, sine and square wave outputs and 3.0V voltage regulator output are all enabled. VPA output is disabled as well as all other circuits. PRETX Oscillator circuits, sine and square wave outputs, 3.0V voltage regulator output, and negative voltage generator are enabled. VBIAS is set to –3.0V. VPA output is disabled and PA bias control loop is inactive. TRANSMIT Crystal oscillator circuits, sine and square wave outputs, 3.0V voltage regulator, negative voltage generator, and VPA output are enabled, and VBIAS is voltage controlled so that the VPA current is proportional to the ICON input voltage. 6 10 PRELIMINARY DATASHEET January, 2000 ML2731 PRELIMINARY FUNCTIONAL DESCRIPTION CRYSTAL OSCILLATOR NEGATIVE VOLTAGE GENERATOR The crystal oscillator circuit is powered by an on chip regulator and generates a square wave signal and a sine wave signal. The sine wave is intended for radio PLL circuits, and the square wave clock for the digital circuits. When driven by a 32 MHz crystal, the charge pump of the ML2731 is clocked with a 2.66 MHz signal. Because the clock frequency is so high, the negative voltage generator requires only small ceramic capacitors on C1 and C2 for operation. (Figure 4) Typically they have values of 100nF. The quick response time (Figure 5), due in part to the small circuit capacitance, allows the charge pump to be disabled when not needed thus reducing power consumption. The frequency range of operation is 10 to 40MHz (determined by the external crystal). The crystal oscillator can also be overdriven by connecting an external oscillator to pin 15 (XIN). 100nF The crystal oscillator square wave and sine wave signal outputs are enabled in STANDBY, PRETX and TRANSMIT modes. (See Figures 2 and 3) 100nF 100nF The oscillator circuit is enabled by the PDN logic control pin and turns on and generates stable output signals within 20mS of being enabled. 3.5 3.0 VNEG 11 C2 12 C1 Figure 4: Typical C1 and C2 Noise Shunt Configuration NEGEN (pin 7) enables the negative voltage generator during the PRETX and TRANSMIT modes of operation. Output from the negative voltage generator is used internally by the ML2731 to supply the op amp in the PA current control circuit. The resulting voltage is applied to VBIAS for controlling an external PA. The negative voltage generator enables the ML2731 to provide a typical bias voltage in the range of –2.9 V to 0V. 2.0 1.5 0.5 4.0 1.0 0.0 3.5 0.5 VNEG CONTROL (V) 3.0 0.0 –0.5 VNEG BIAS 0 10 20 40 30 50 TIME (ns) Figure 2: Typical 32 MHz Square wave output signal (1kW+10pF load, VCC = 3.3V) 2.5 –1.0 2.0 –1.5 1.5 –2.0 1.0 –2.5 0.5 –3.0 0 1.9 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 –3.5 0.8 TIME (ms) Cap: 10pF none 1.8 –0.5 BIAS (V) 2.5 VOLTAGE (V) 10 Figure 5: Typical negative voltage generator on and off timing (using 100nF capacitors on pins C1 and C2) 1.7 500 VNEG (µVRMS) VOLTAGAE (V) 600 1.6 1.5 400 300 200 100 1.4 0 10 20 30 40 50 60 70 80 TIME (ns) 0 0 2 4 6 8 10 FREQUENCY (MHz) Figure 3: Typical 32 MHz sine wave output signal (1kW+0pF load, and 1kW+10pF load, VCC = 3.3V) January, 2000 Figure 6: Negative voltage output ripple (mV) (using 100nF bypass and reservoir capacitance) PRELIMINARY DATASHEET 7 PRELIMINARY ML2731 FUNCTIONAL DESCRIPTION PA SUPPLY DC SWITCH PA CURRENT CONTROL LOOP The ML2731 includes a DC switch for connecting the supply voltage to an external PA. PAEN activates the DC switch during TRANSMIT mode. To ensure the external PA devices power up correctly, the chip has control circuits preventing the PA supply DC switch from being enabled if the VBIAS voltage is more positive than –3.0V. The current control loop allows the PA current to be set by the reference current on the ICON pin. This enables the ML2731 to control PA output power and to compensate for PA current variations due temperature changes. In addition, it removes the need for calibration of PA current in manufacturing because the PA current control loop adjusts the PA bias be proportional to a reference voltage. VBIAS (V) Typically, the PA supply DC switch produces a voltage drop of 100mV while conducting a 500mA current. Parameters determining the maximum current capability of the DC switch are the maximum voltage drop that can be tolerated by the external PA and the thermal limitations of the ML2731. 2 140 1 120 VBIAS 0 100 PAEN Enable Logic 80 VPA Current -1 The current control loop is enabled by the PAEN pin. PA CURRENT CONTROL LOOP AND PA RAMP COMPONENT VALUES The ICON input pin is at virtual ground. The reference current on the ICON pin is determined by the value of REXT, connected to the ICON input, the voltage reference (VREF), and the voltage source impedance. For the fixed voltage source in the above circuit, the PA current is determined by the formula: 60 -2 VPA current = [Vcc(R1/(R2+REXT))*2000] / REXT + Offset 40 -3 The offset current (minimum PA current) is typically 30mA 20 -4 0 -1 0 1 2 3 4 5 6 7 8 9 A typical REXT resistor value is 12kW. Typical reference voltages are in the range 0 to 3.0V to enable the PA current to be controlled over the range of 30mA to 500mA. Time (µsec) Figure 7: VPA Current ramp following PAEN enable (VBIAS voltage and VPA current values and rise times are determined by PA current control loop component values) 1 120 0.5 100 0 VBIAS (V) The PA current can typically is between 30 to 500mA. The typical control loop bandwidths for typical values of capacitance on VBIAS are shown in Figure 13. 80 -0.5 -1 60 -1.5 40 -2 For slow PA ramp on/off times (e.g. >10msec) the PA bias control loop has a sufficiently fast settling time to enable the ramp to be controlled by ramping the ICON voltage input. For fast, e.g. <10msec PA ramp on/off times, the ramp time is set by the value of the capacitance from VBIAS to ground and VPA to ground. V BIAS PAEN Enable Signal VPA Current 20 -2.5 0 -3 -3.5 -10 0 10 20 Time (µsec) -20 30 Figure 8: VPA Current ramp following PAEN disable (Vbias voltage and VPA current values and fall times are determined by PA current control loop component values as detailed below) 8 PRELIMINARY DATASHEET January, 2000 ML2731 PRELIMINARY FUNCTIONAL DESCRIPTION VCC Supply Voltage PA Enable signal (PAEN) PA on/off switch and current sense Baseband IC VPA VCC DAC Reference current for PA control OR REXT VCC R1 Drain PA Bias controller Increase gate voltage to increase PA current Measure error (wanted current Vs actual current) VBIAS Gate bias PA (GaAs FET) VREF Source Negative voltage generator R2 GND Figure 9: PA Current Control Loop Circuits VPA Current vs. Vcontrol 600 VPA current (mA) 500 400 12KΩ 300 24KΩ 200 100 0 0 0.5 1 1.5 2 2.5 3 V Control (V) Figure 10: PA Current Control Loop Operation With REXT At 12kW and 24kW January, 2000 PRELIMINARY DATASHEET 9 ML2731 PRELIMINARY FUNCTIONAL DESCRIPTION RECOMMENDED PA BIAS OPERATION VREF An example of how the PA bias operates is shown in Figure 11. A three-step reference voltage ramp is generated using an external baseband circuit and is applied to the ICON pin via an external resistor. The ML2731 current control loop uses this input as a reference to set the PA current and therefore generates a current ramp output (and hence PA power ramp output.) The rate of change of negative bias and PA current is determined by the capacitance on the VBIAS pin and on the VPA pin. Note sufficient time should be allowed for the negative voltage generator to reach a steady state, prior to enabling the PA. 160 0.9 140 0.8 120 100 0.6 >0µsec >0µsec 0.5 80 0.4 60 0.3 PDN 0.2 VNEG 0.1 40 20 0 0 PAEN VPA current (mA) 0.7 VREF (V) >0µsec >200µs VPA Current 1 0 3V VControl Voltage 0V 5 10 15 20 Time (µsec) Figure 12: VPA output vs VREF (TRANSMIT mode, REXT = 12kW, capacitance on VBIAS = 3.3nF) 0V VBIAS Voltage -3V Charge VNEG caps Current discharge VNEG caps Timeconstant set by external caps on VPA VPAout current Timeconstant set by external caps on VBIAS 1 Figure 11: PA Bias Control Loop Operation 1msec ramp-up for 2nF VBIAS capacitance 4msec ramp-up for 22nF VBIAS capacitance An example of a 3 step current ramp up and ramp down, with 3.3nF capacitance on VBIAS, is shown in Figure 12. 0 -1 Drain Current(dB) Where ICON is a fixed value (i.e. the VPA current is not ramped up and down by changing the value of ICON) then the time taken for the VPA current to ramp up following PAEN being enabled is determined by the capacitor values on VBIAS and VPA. The time taken for the current to ramp down following PAEN being disabled is determined by the capacitance value on VPA only. Example timings are: -2 -3 -4 -5 -6 -7 10 100 3.3nF Frequency(KHz) 2.2nF 1.5nF Figure 13: Bandwidth of PA Current control loop for 3.3nF, 2.2nF and 1.5nF VBIAS capacitance 10 PRELIMINARY DATASHEET January, 2000 100 ML2731 PRELIMINARY ELECTRICAL CHARACTERISTICS ABSOLUTE MAXIMUM RATINGS OPERATING CONDITIONS Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. Commercial Temperature Range .................... 0°C to 70°C Extended Temperature Range .................... –20°C to 70°C VCC Range .................................................. 3.3V to 5.5V Thermal Resistance (qJA) ................................... 100°C/W VCC ......................................................................... 6.0V All Other Inputs .................... GND –0.3V to VCC + 0.3V Junction Temperature .............................................. 150°C Storage Temperature Range ..................... –65°C to 150°C Lead Temperature (Soldering, 10 sec) ..................... 260°C ELECTRICAL TABLES Unless otherwise specified, VCC = 3.3, TA = Operating Temperature Range. (Note 1) SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS POWER CONSUMPTION All circuits, supply current, all circuits disabled DC Connected 1 µA Supply current, oscillator enabled, regulator enabled 10pF load on CLKO and SINO 0mA from VREG 5 mA Supply current, oscillator and negative voltage generator enabled. 10pF load on CLKO and SINO <1mA current on VBIAS 6 mA 9 mA Supply current, all circuits enabled NEGATIVE VOLTAGE GENERATION Negative Bias Voltage Current <3mA –2.9 0 Maximum current, VBIAS Turn on time, to –3V on VBIAS 3 Clock 10MHz. PA DISABLED V mA 100 µs VCONTROL VOLTAGE INPUT Input control voltage range 2.9 0 V VOLTAGE REGULATOR OUTPUT Output voltage 3.0 Output current V 50 mA 40 MHz OSCILLATOR AND OUTPUTS Frequency Range 10 Turn on time 5 ms SINO voltage range, Peak-to-Peak 450 mV CLKO, low 0.4 V CLKO, high VCC – 0.4 V Capacitive Load on CLKO 2k shunt R to ground in parallel 15 pF Capacitive Load on SINO 2k shunt R to ground in parallel 10 pF PA SUPPLY VOLTAGE Voltage VCC – 0.1 VCC V Current 0 500 mA Note 1: Limis are guaranteed by 100% testing, sampling, or correlation with worst case test condidtions. January, 2000 PRELIMINARY DATASHEET 11 ML2731 PRELIMINARY PHYSICAL DIMENSIONS Package: T16 16-Pin TSSOP 0.192 - 0.202 (4.88 - 5.13) 16 0.169 - 0.177 (4.29 - 4.50) 0.246 - 0.258 (6.25 - 6.55) PIN 1 ID 1 0.026 BSC (0.65 BSC) 0.043 MAX (1.10 MAX) 0º - 8º 0.033 - 0.037 (0.84 - 0.94) 0.008 - 0.012 (0.20 - 0.30) SEATING PLANE 0.020 - 0.028 (0.51 - 0.71) 0.002 - 0.006 (0.05 - 0.15) 0.004 - 0.008 (0.10 - 0.20) ORDERING INFORMATION PART NUMBER TEMPERATURE RANGE PACKAGE ML2731CT 0°C to 70°C TSSOP ML2731ET -20°C to 70°C TSSOP Micro Linear Corporation 2092 Concourse Drive San Jose, CA 95131 Tel: (408) 433-5200 Fax: (408) 432-0295 www.microlinear.com DS2731-01 12 PRELIMINARY DATASHEET January, 2000