TI TAS5036PFCR

Data Manual
November 2002
DAV Digital Audio/Speaker
SLES044B
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third–party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Mailing Address:
Texas Instruments
Post Office Box 655303
Dallas, Texas 75265
Copyright  2002, Texas Instruments Incorporated
Contents
Contents
Section
1
2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1.2
Functional Block Diagram . . . . . . . . . . . . .
2
1.3
Terminal Assignments . . . . . . . . . . . . . . . .
3
1.4
Ordering Information . . . . . . . . . . . . . . . . .
4
1.5
Terminal Functions . . . . . . . . . . . . . . . . . . .
4
Architecture Overview . . . . . . . . . . . . . . . . . . . . .
6
2.1
Clock and Serial Data Interface . . . . . . . .
6
2.1.1
Normal-Speed, Double-Speed,
and Quad-Speed Selection . .
6
2.1.2
Clock Master/Slave Mode
(M_S) . . . . . . . . . . . . . . . . . . . .
7
2.1.3
Clock Master Mode . . . . . . . . .
7
2.1.4
Clock Slave Mode . . . . . . . . . .
8
2.1.5
PLL Filter . . . . . . . . . . . . . . . . .
10
2.1.6
DCLK . . . . . . . . . . . . . . . . . . . . .
10
2.1.7
Serial Data Interface . . . . . . . .
10
2.2
Reset, Power Down, and Status . . . . . . .
15
2.2.1
Reset—RESET . . . . . . . . . . . .
15
2.2.2
Power Down—PDN . . . . . . . .
16
2.2.3
Status Registers . . . . . . . . . . .
16
2.3
Signal Processing . . . . . . . . . . . . . . . . . . .
17
2.3.1
Volume Control . . . . . . . . . . . .
17
2.3.2
Mute . . . . . . . . . . . . . . . . . . . . .
18
2.3.3
Auto Mute . . . . . . . . . . . . . . . . .
18
2.3.4
Individual Channel Mute . . . . .
18
2.3.5
De-Emphasis Filter . . . . . . . . .
18
November 2002
Page
2.4
3
4
5
Pulse Width Modulator (PWM) . . . . . . . . .
19
2.4.1
Clipping Indicator . . . . . . . . . . .
19
2.4.2
Error Recovery . . . . . . . . . . . .
19
2.4.3
Individual Channel Error Recovery . . . . . . . . . . . . . . . . . . . .
20
2.4.4
PWM DC-Offset Correction . .
20
2.4.5
Inter-Channel Delay . . . . . . . .
20
2.4.6
ABD Delay . . . . . . . . . . . . . . . .
20
2.4.7
PWM/H-Bridge and Discrete
H-Bridge Driver Interface . . . .
21
2.5
I2C Serial Control Interface . . . . . . . . . . .
21
2.5.1
Single Byte Write . . . . . . . . . . .
22
2.5.2
Multiple Byte Write . . . . . . . . .
22
2.5.3
Single Byte Read . . . . . . . . . . .
23
2.5.4
Multiple Byte Read . . . . . . . . .
23
Serial Control Interface Register Definitions .
24
3.1
General Status Register (x00) . . . . . . . . .
25
3.2
Error Status Register (x01) . . . . . . . . . . . .
25
3.3
System Control Register 0 (x02) . . . . . . .
25
3.4
System Control Register 1 (x03) . . . . . . .
26
3.5
Error Recovery Register (x04) . . . . . . . . .
26
3.6
Automute Delay Register (x05) . . . . . . . .
26
3.7
DC-Offset Control Registers (x06–x0B) .
27
3.8
Interchannel Delay Registers (x0C–x11)
27
3.9
ABD Delay Register (x12) . . . . . . . . . . . . .
27
3.10
Individual Channel Mute Register (x19) .
27
System Initialization . . . . . . . . . . . . . . . . . . . . . . .
28
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
29
SLES044B
3
List of Illustrations
5.1
5.2
5.3
5.4
Absolute Maximum Ratings Over Operating Temperature Ranges . . . . . . . . . . . . . .
29
Recommended Operating Conditions (Fs
= 48 kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . .
29
Electrical Characteristics Over Recommended Operating Conditions . . . . . . . . .
29
5.3.1
Static Digital Specifications
Over Recommended Operating Conditions . . . . . . . . . . . . .
29
5.3.2
Digital Interpolation Filter and
PWM Modulator Over Recommended Operating Conditions
Fs = 48 kHz . . . . . . . . . . . . . . .
29
5.3.3
TAS5036/TAS5100 System
Performance Measured at the
Speaker Terminals Over
Recommended Operating
Conditions . . . . . . . . . . . . . . . . .
30
6
Switching Characteristics . . . . . . . . . . . . .
30
5.4.1
Command Sequence Timing .
30
5.4.2
Serial Audio Port . . . . . . . . . . .
34
5.4.3
Serial Control Port—I2C Operation . . . . . . . . . . . . . . . . . . . .
37
Application Information . . . . . . . . . . . . . . . . . . . .
38
6.1
Serial Audio Interface Clock Master and
Slave Interface Configuration . . . . . . . . . .
39
6.1.1
Slave Configuration . . . . . . . . .
39
6.1.2
Master Configuration . . . . . . .
39
Appendix A—Volume Table . . . . . . . . . . . . . . . . . . . .
41
List of Illustrations
Figure
2–1 Crystal Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
2–2 External PLL Loop Filter . . . . . . . . . . . . . . . . . . . .
10
2–3 I2S 64-Fs Format . . . . . . . . . . . . . . . . . . . . . . . . . .
11
2–4 I2S 48-Fs Format . . . . . . . . . . . . . . . . . . . . . . . . . .
12
2–5 Left-Justified 64-Fs Format . . . . . . . . . . . . . . . . . .
12
2–6 Left-Justified 48-Fs Format . . . . . . . . . . . . . . . . . .
13
2–7 Right-Justified 64-Fs Format . . . . . . . . . . . . . . . . .
13
2–8 Right-Justified 48-Fs Format . . . . . . . . . . . . . . . . .
14
2–9 DSP Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
2–10 Attenuation Curve . . . . . . . . . . . . . . . . . . . . . . . . .
17
2–11 De-Emphasis Filter Characteristics . . . . . . . . . .
19
4
SLES044B
Title
Page
2–12 PWM Outputs and H-Bridge Driven in BTL
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . .
21
2–13 Typical I2C Sequence . . . . . . . . . . . . . . . . . . . . .
22
2–14 Single Byte Write Transfer . . . . . . . . . . . . . . . . .
22
2–15 Multiple Byte Write Transfer . . . . . . . . . . . . . . . .
23
2–16 Single Byte Read . . . . . . . . . . . . . . . . . . . . . . . . .
23
2–17 Multiple Byte Read . . . . . . . . . . . . . . . . . . . . . . . .
23
4–1 RESET During System Initialization . . . . . . . . . . .
28
5–1 RESET Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
30
5–2 Power-Down and Power-Up Timing—RESET
Preceding PDN . . . . . . . . . . . . . . . . . . . . . . . . .
31
5–3 Power-Down and Power-Up Timing—RESET
Following PDN . . . . . . . . . . . . . . . . . . . . . . . . . .
32
5–4 Error Recovery Timing . . . . . . . . . . . . . . . . . . . . . .
33
November 2002
List of Tables
5–5 Mute Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33
5–6 Right-Justified, IIS, Left-Justified Serial Protocol
Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
34
5–7 Right, Left, and IIS Serial Mode Timing
Requirement . . . . . . . . . . . . . . . . . . . . . . . . . . . .
35
5–8 Serial Audio Ports Master Mode Timing . . . . . . .
35
5–9 DSP Serial Port Timing . . . . . . . . . . . . . . . . . . . . .
35
5–10 DSP Serial Port Expanded Timing . . . . . . . . . . .
36
5–11 DSP Absolute Timing . . . . . . . . . . . . . . . . . . . . . .
36
5–12 SCL and SDA Timing . . . . . . . . . . . . . . . . . . . . . .
37
5–13 Start and Stop Conditions Timing . . . . . . . . . . . .
37
6–1 Typical TAS5036 Application . . . . . . . . . . . . . . . . .
38
6–2 TAS5036 Serial Audio Port—Slave Mode
Connection Diagram . . . . . . . . . . . . . . . . . . . . .
39
6–3 TAS5036 Serial Audio Port—Master Mode
Connection Diagram . . . . . . . . . . . . . . . . . . . . .
39
List of Tables
Table
2–1 Normal-Speed, Double-Speed, and Quad-Speed
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
2–2 Master and Slave Clock Modes . . . . . . . . . . . . . .
9
2–3 LRCLK, MCLK_IN, and External PLL Rates . . .
9
2–4 DCLK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
2–5 Supported Word Lengths . . . . . . . . . . . . . . . . . . . .
11
2–6 Device Outputs During Reset . . . . . . . . . . . . . . . .
15
2–7 Values Set During Reset . . . . . . . . . . . . . . . . . . . .
15
2–8 Device Outputs During Power Down . . . . . . . . . .
16
2–9 Volume Register . . . . . . . . . . . . . . . . . . . . . . . . . . .
18
2–10 De-Emphasis Filter Characteristics . . . . . . . . . .
18
2–11 Device Outputs During Error Recovery . . . . . . .
20
November 2002
Title
Page
3–1 I2C Register Map . . . . . . . . . . . . . . . . . . . . . . . . . .
24
3–2 General Status Register (Read Only) . . . . . . . . .
25
3–3 Error Status Register . . . . . . . . . . . . . . . . . . . . . . .
25
3–4 System Control Register 0 . . . . . . . . . . . . . . . . . .
25
3–5 System Control Register 1 . . . . . . . . . . . . . . . . . .
26
3–6 Error Recovery Register . . . . . . . . . . . . . . . . . . . .
26
3–7 Automute Delay Register . . . . . . . . . . . . . . . . . . . .
26
3–8 DC-Offset Control Registers . . . . . . . . . . . . . . . . .
27
3–9 Six Inter-Channel Delay Registers . . . . . . . . . . . .
27
3–10 ABD Delay Register . . . . . . . . . . . . . . . . . . . . . . .
27
3–11 Individual Channel Mute Register . . . . . . . . . . . .
27
SLES044B
5
1
Introduction
The TAS5036 is an innovative, cost-effective, high-performance 24-bit six-channel digital pulse width
modulator (PWM) based on Equibit technology. Combined with a TI digital amplifier power stage, these
devices use noise-shaping and sophisticated error correction algorithms to achieve high power efficiency and
high-performance digital audio reproduction. The TAS5036 is designed to drive up to six digital power devices
to provide six channels of digital audio amplification. The digital power devices can be six conventional
monolithic power stages (such as the TAS5110) or six discrete differential power stages using gate drivers
and MOSFETs.
The TAS5036 has six independent volume controls and mute. It is designed to drive a digital amplifier power
stage (such as the TAS5182) in an H-bridge (bridge tied load) configuration. The device operates in AD and
BD modes. This all-digital audio system contains only two analog components in the signal chain—an LC
low-pass filter at each speaker terminal and can provide up to 96-dB SNR at the speaker terminals. The
TAS5036 has a wide variety of serial input options including right justified (16, 20, or 24 bit), I2S (16, 20, or
24 bit) left justified, or DSP (16-bit) data formats. The device is fully compatible with AES standard sampling
rates of 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, and 192 kHz including de-emphasis for 44.1-kHz and
48-kHz sample rates. The TAS5036 plus the TAS51xx power stage device combination was designed for
home theater applications such as DVD minicomponent systems, home theater in a box (HTIB), DVD receiver,
A/V receiver, or TV sets.
1.1
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
True Digital Audio Amplifier
High Quality Audio
– 96-dB SNR
– <0.1% THD+N
Six-Channel Volume Control
– Patented Soft Volume
– Patented Soft Mute
16-, 20-, or 24-Bit Input Data
Sampling Rates: 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, and 192 kHz
Supports Master and Slave Modes
3.3-V Power Supply Operation
Economical 80-Pin TQFP Package
De-Emphasis: 32 kHz, 44.1 kHz, and 48 kHz
High Power Efficiency
Clock Oscillator Circuit for Master Modes
Low Jitter Internal PLL
Soft Volume and Mute Update
Excellent PSRR
Equibit is a trademark of Texas Instruments Incorporated.
SLES044B—November 2002
TAS5036
1
Introduction
DVSS_PWM
DVDD_PWM
DVSS_RCL
DVDD_RCL
VREGC_CAP
VREGB_CAP
VREGA_CAP
AVSS_PLL
Functional Block Diagram
AVDD_PLL
1.2
Power Supply
PWM
Section
MCLK_IN
XTAL_OUT
XTAL_IN
PLL_FLT_OUT
PLL_FLT_RET
SCLK
LRCLK
Clock,
PLL
and
Serial
Data
I/F
Signal
Processing
RESET
PDN
Serial
Control
I/F
Reset,
Pwr Dwn
and
Status
PWM_AP_2
PWM_AM_2
Valid_2
PWM Ch.
MCLKOUT
SDIN1
SDIN2
SDIN3
SDA
SCL
CSO
PWM_AM_1
Valid_1
PWM Ch.
Auto Mute
De-emphasis
Soft Volume
Error Recovery
Soft Mute
Clip Detect
PWM Ch.
PWM Ch.
Output Control
CSS
M_S
PWM_AP_1
PWM AP_3
PWM AM_3
Valid_3
PWM_AP_4
PWM_AM_4
Valid_4
PWM_AP_5
PWM_AM_5
PWM Ch.
Valid_5
PWM Ch.
PWM_AP_6
PWM_AM_6
Valid_6
CLIP
MUTE
ERR_RCVY
2
TAS5036
SLES044B—November 2002
Introduction
1.3
Terminal Assignments
AVDD_OSC
XTL_IN
XTL_OUT
AVSS_OSC
DVSS
PWM_AP1
PWM_AM_1
VALID_1
PWM_BM_1
PWM_BP_1
PWM_AP_2
PWM_AM_2
VALID_2
PWM_BM_2
PWM_BP_2
PWM_AP_3
PWM_AM_3
VALID_3
PWM_BM_3
PWM_BP_3
PAG PACKAGE
(TOP VIEW)
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61
1
60
2
59
3
58
4
57
5
56
6
55
7
54
8
53
9
52
10
51
11
50
12
49
13
48
14
47
15
46
16
45
17
44
18
43
19
42
20
41
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
VREGP_CAP
DVDD_RCL
DVSS_RCL
DVDD_PWM
DVSS_PWM
PWM_AP_4
PWM_AM_4
VALID_4
PWM_BM_4
PWM_BP_4
PWM_AP_5
PWM_AM_5
VALID_5
PWM_BM_5
PWM_BP_5
PWM_AP_6
PWM_AM_6
VALID_6
PWM_BM_6
PWM_BP_6
NC
NC
NC
DBSPD
CLIP
SDIN1
SDIN2
SDIN3
MCLK_OUT
SCLK
LRCLK
DVDD
DVSS
VREGC_CAP
DEM_SEL2
DEM_SEL1
M_S
DVSS1
DVSS1
NC
NC
NC
MCLK_IN
AVDD_PLL
PLL_FLT_OUT
PLL_FLT_RET
AVSS_PLL
NC
VREGA_CAP
DVSS1
NC
RESET
ERR_RCVRY
MUTE
PDN
SDA
SCL
CS0
NC
NC
NC – No internal connection
SLES044B—November 2002
TAS5036
3
Introduction
1.4
Ordering Information
T
AS
5036
C
PAG
Texas Instruments
Audio Solutions
Device Number
Temperature Range
Package Type
AVAILABLE OPTIONS
PACKAGE
1.5
TA
PLASTIC 80-PIN TQFP
(PAG)
0°C to 70°C
TAS5036CPAG
Terminal Functions
TERMINAL
NAME
AVDD_OSC
NO.
80
I/O
DESCRIPTION
P
Analog power supply for internal oscillator cells
Analog power supply for PLL
AVDD_PLL
4
P
AVSS_OSC
77
AO
AVSS_PLL
7
P
CLIP
25
DO
CS0
18
DI
Digital clipping indicator, active low
I2C serial control chip address select input, active high
DBSPD
24
DI
Sample rate is double speed (88.2 kHz or 96 kHz), active high
DM_SEL1
36
DI
De-emphasis select bit 2, 10 = 48 kHz, 11= undefined (none)
DM_SEL2
35
DI
De-emphasis select bit 1 (0 = none, 01 = 32 kHz, 10 = 44.1 kHz
DVDD
32
P
Digital power supply
DVDD_PWM
57
P
Digital power supply for PWM
DVDD_RCL
Analog ground for internal oscillator cells
Analog ground for PLL
59
P
Digital power supply for reclocker
DVSS
33, 76
P
Digital ground for digital core and most of I/O buffers
DVSS1
10, 38, 39
DIO
Digital ground for digital core and most of I/O buffers
DVSS_PWM
56
P
Digital ground for PWM
DVSS_RCL
58
P
Digital ground for reclocker
ERR_RCVRY
13
DI
Error recovery input, active low
LRCLK
31
DIO
M_S
37
DI
Master/slave mode input signal (master = 1, slave = 0)
Serial audio data left / right clock (sampling rate clock) (input when M_S = 0; output when M_S = 1)
MCLK_IN
3
DI
MCLK input, slave mode (or master / double-speed mode)
MCLK_OUT
29
DO
MCLK output buffered system clock output if M_S = 1; otherwise set to 0
MUTE
14
DI
Mute input signal, active low (muted signal = 0, normal mode = 1)
N/C
1, 2, 8, 11,
19–23, 40
PDN
15
4
TAS5036
Not connected
DI
Power down, active low
SLES044B—November 2002
Introduction
TERMINAL
NAME
NO.
PLL_FLT_OUT
5
I/O
DESCRIPTION
AO
PLL external filter
PLL_FLT_RET
6
AO
PLL external filter (internally connected to AVSS_PLL)
PWM_AM_1
74
DO
PWM 1 output (differential -); {positive H-bridge side}
PWM_AM_2
69
DO
PWM 2 output (differential -); {positive H-bridge side}
PWM_AM_3
64
DO
PWM 3 output (differential -); {positive H-bridge side}
PWM_AM_4
54
DO
PWM 4 output (differential -); {positive H-bridge side}
PWM_AM_5
49
DO
PWM 5 output (differential -); {positive H-bridge side}
PWM_AM_6
44
DO
PWM 6 output (differential -); {positive H-bridge side}
PWM_AP_1
75
DO
PWM 1 output (differential +); {positive H-bridge side}
PWM_AP_2
70
DO
PWM 2 output (differential +); {positive H-bridge side}
PWM_AP_3
65
DO
PWM 3 output (differential +); {positive H-bridge side}
PWM_AP_4
55
DO
PWM 4 output (differential +); {positive H-bridge side}
PWM_AP_5
50
DO
PWM 5 output (differential +); {positive H-bridge side}
PWM_AP_6
45
DO
PWM 6 output (differential +); {positive H-bridge side}
PWM_BM_1
72
DO
PWM 1 output (differential -); {negative H-bridge side}
PWM_BM_2
67
DO
PWM 2 output (differential -); {negative H-bridge side}
PWM_BM_3
62
DO
PWM 3 output (differential -); {negative H-bridge side}
PWM_BM_4
52
DO
PWM 4 output (differential -); {negative H-bridge side}
PWM_BM_5
47
DO
PWM 5 output (differential -); {negative H-bridge side}
PWM_BM_6
42
DO
PWM 6 output (differential -); {negative H-bridge side}
PWM_BP_1
71
DO
PWM 1 output (differential +); {negative H-bridge side}
PWM_BP_2
66
DO
PWM 2 output (differential +); {negative H-bridge side}
PWM_BP_3
61
DO
PWM 3 output (differential +); {negative H-bridge side}
PWM_BP_4
51
DO
PWM 4 output (differential +); {negative H-bridge side}
PWM_BP_5
46
DO
PWM 5 output (differential +); {negative H-bridge side}
PWM_BP_6
41
DO
PWM 6 output (differential +); {negative H-bridge side}
RESET
12
DI
System reset input, active low
SCL
17
DI
I2C serial control clock input
SCLK
30
DIO
Serial audio data clock (shift clock)
SDA
16
DIO
I2C serial control data input/ output
SDIN1
26
DI
Serial audio data 1 input
SDIN2
27
DI
Serial audio data 2 input
SDIN3
28
DI
Serial audio data 3 input
VALID_1
73
DO
Output indicating validity of PWM outputs, channel 1, active high
VALID_2
68
DO
Output indicating validity of PWM outputs, channel 2, active high
VALID_3
63
DO
Output indicating validity of PWM outputs, channel 3, active high
VALID_4
53
DO
Output indicating validity of PWM outputs, channel 4, active high
VALID_5
48
DO
Output indicating validity of PWM outputs, channel 5, active high
VALID_6
43
DO
Output indicating validity of PWM outputs, channel 6, active high
VREGA_CAP
9
P
C05 voltage regulator capacitor
VREGB_CAP
60
P
C05 voltage regulator capacitor
VREGC_CAP
34
P
C05 voltage regulator capacitor
XTL_IN
79
AI
Crystal or TTL level clock input
XTL_OUT
78
AO
Crystal output (not for external usage)
SLES044B—November 2002
TAS5036
5
Architecture Overview
2
Architecture Overview
The TAS5036 is composed of six functional elements:
•
•
•
•
•
•
2.1
Clock, PLL, and serial data interface (IIS)
Reset/power down circuitry
Serial control interface (IIC)
Signal processing unit
Pulse width modulator (PWM)
Power supply
Clock and Serial Data Interface
The TAS5036 clock and serial data interface contains an input serial data slave and the clock master/ slave
interface.
The serial data slave interface receives information from a digital source such as a DSP, S/PDIF receiver,
analog-to-digital converter (ADC), digital audio processor (DAP) such as the TAS3103, or other serial bus
master at sample rates of for sample rates of 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz,176.4 kHz, and 192
kHz. The serial data interface has three serial data inputs that can accept up to six channels of data. The serial
data interfaces support left justified and right justified for 16-, 20-, and 24-bits. In addition, the serial data
interfaces support the DSP protocol for 16 bits and the I2S protocal for 24 bits. The received data is data
passed to the TAS5036 signal-processing unit.
The TAS5036 can function as a receiver or a generator for the MCLK_IN (master clock), SCLK (shift clock),
and LRCLK (left/right clock) signals that control the flow of data on the three serial data interfaces. The
TAS5036 is a clock master when it generates these clocks and is a clock slave when it receives these clocks.
The TAS5036 is a synchronous design that relies upon master clock to provide a reference clock for all of the
device operations. When operating as a slave, this reference clock is MCLK_IN. When operating as a master,
the reference clock is either TTL clock input to XTAL_IN or a crystal attached across XTAL_IN and XTAL_OUT.
If the master clock stops, the TAS5036 will perform a clock error recovery sequence. The clock error recovery
sequence temporarily suspends processing, places the PWM outputs in a hard mute (PWM P outputs are low;
PWM M outputs are high, and all VALID signals are low), resets all internal processes, sets the volumes to
mute, and suspends all I2C operations.
When the master clock is resumed, the TAS5036 exits the clock error recovery sequence by performing a
4.3-ms partial re–initialization, noiselessly restarting the PWM output, and ramping the volume up to the level
specified in the volume control registers. The volume update is performed over a 43 ms. interval. The TAS5036
will preserve all control register settings that were set prior to the clock interruption.
Quad–speed mode is used to support sampling rates of 176.4 kHz and 192 kHz. Quad–speed mode is auto
detected supported in slave mode and invoked by control in master mode in slave mode. If the device is not
in double speed mode, quad–speed mode is automatically detected when MCLK_IN is 128Fs. In master
mode, the PWM is placed in quad–speed mode by setting the quad–speed bit in the system control register
through the serial control interface.
The clock and serial data interface has two control parameters: data sample rate and clock master or slave.
2.1.1 Normal-Speed, Double-Speed, and Quad-Speed Selection
The sampling rate is selected through a pin (DBSPD) or the serial control register 0 (X02). When a sample
rate is selected, the system automatically performs an error recovery sequence and switches to the new
sampling rate. As shown in subsequent sections, the sample rate control sets the frequencies of the SCLK
and LRCLK in clock slave mode and the output frequencies of SCLK and LRCLK in clock master mode.
The reference clock for the PLL can be provided by either an external clock source (attached to XTAL_IN) or
a crystal (connected across terminals XTAL_IN and XTAL_OUT). The external source attached to MCLK_IN
is 256 times (128 in quad mode) the data sample rate (Fs). The SCLK frequency is 64 times the data sample
rate and the SCLK frequency of 48 times the data sample rate is not supported in the master mode. The LRCLK
frequency is the data sample rate.
6
TAS5036
SLES044B—November 2002
Architecture Overview
There are three data rates: normal speed, double speed, and quad speed.
Normal-speed mode supports data rates of 32 kHz, 44.1 kHz, and 48 kHz. Normal speed is supported in the
master and slave modes. The PWM is placed in normal speed by setting the DBSPD terminal low or by setting
the normal mode bits in the system control register through the serial control interface. Following this
operation, the PWM performs an error recovery sequence automatically and operates in the normal speed
mode.
Double-speed mode is used to support sampling rates of 88.2 kHz and 96 kHz. Double speed is supported
in master and slave modes. The PWM is placed in double speed mode by setting the DBSPD terminal high
or by setting the double speed bits in the system control register through the serial control interface. Following
this operation, the PWM performs an error recovery sequence automatically and operates in the double speed
mode.
Quad-speed mode is used to support sampling rates of 176.4 kHz and 192 kHz. Quad-speed mode is auto
detected supported in slave mode and invoked by control in master mode in slave mode. If the device is not
in double speed mode, quad-speed mode is automatically detected when MCLK_IN is 128Fs. In master mode,
the PWM is placed in quad-speed mode by setting the quad-speed bit in the system control register through
the serial control interface.
Table 2–1. Normal-Speed, Double-Speed, and Quad-Speed Operation
QUAD-SPEED CONTROL
REGISTER BIT
DBSPD TERMINAL OR
CONTROL REGISTER BIT
MODE
SPEED SELECTION
0
0
Master or slave
Normal speed
0
1
Master or slave
Double speed
1
0
Master or slave
Quad speed
0
0
Slave
Quad speed if MCLK_IN = 128Fs
1
1
Master or slave
Error
2.1.2 Clock Master/Slave Mode (M_S)
Clock master and slave mode can be invoked using the M_S (master slave) terminal.
This terminal specifies the default mode that is set immediately following a device RESET. The serial data
interface setting permits the clock generation mode to be changed during normal operation.
The transition to master mode occurs:
•
Following a RESET when M_S terminal has a logic high applied
The transition to slave mode occurs:
•
Following a RESET when M_S terminal has a logic low applied
2.1.3 Clock Master Mode
When M_S = 1 following a RESET, the TAS5036 provides the master clock, SCLK, and LRCLK to the rest of
the system. In the master mode, the TAS5036 outputs the audio system clocks MCLK_OUT, SCLK, and
LRCLK.
The TAS5036 device generates these clocks plus its internal clocks from the internal phase-locked loop (PLL).
The reference clock for the PLL can be provided by either an external clock source (attached to XTAL_IN) or
a crystal (connected across terminals XTAL_IN and XTAL_OUT). The external source attached to MCLK_IN
is 256 times (128 in quad mode) the data sample rate (Fs). The SCLK frequency is 64 times the data sample
rate and the SCLK frequency of 48 times the data sample rate is not supported in the master mode. The LRCLK
frequency is the data sample rate.
2.1.3.1
Crystal Type and Circuit
In clock master mode the TAS5036 can derive the MCLKOUT, SCLK, and LRCLK from a crystal. In this case,
the TAS5036 uses a parallel-mode fundamental-mode crystal. This crystal is connected to the TAS5036 as
shown in Figure 2–1.
SLES044B—November 2002
TAS5036
7
Architecture Overview
TAS5036
C1
rd
OSC
MACRO
XO
C2
XI
AVSS
rd = Drive level control resistor – crystal vendor specified
CL = Crystal load capacitance (capacitance of circuitry between the two terminals of the crystal)
CL = (C1 x C2 )/(C1 + C2 ) + CS (where CS = board stray capacitance ~ 3 pF)
Example: Vendor recommended CL = 18 pF, CS = 3 pF ≥ C1 = C2 = 2 x (18–3) = 30 pF
Figure 2–1. Crystal Circuit
2.1.4 Clock Slave Mode
In the slave mode (M_S = 0), the master clock, LRCLK, and SCLK are inputs to the TAS5036. The master clock
is supplied through the MCLK_IN terminal.
As in the master mode, the TAS5036 device developed its internal timing from internal phase-locked loop
(PLL). The reference clock for the PLL is provided by the input to the MCLK_IN terminal. This input is at a
frequency of 256 times (128 in quad mode) the input data rate. The SCLK frequency is 48 or 64 times the data
sample rate. The LRCLK frequency is the data sample rate. The TAS5036 does not require any specific phase
relationship between SRCLK and MCLK_IN, but there must be synchronization.
The TAS5036 monitors the relationship between MCLK, SCLK and LRCLK. The TAS5036 will detect if any
of the three clocks are absent, if LRCLK rate changes more the ±10 MCLK cycles since the last device reset
or clock error recovery, or if MCLK frequency is changing substantially with respect to the PLL frequency.
When a clock error is detected the TAS5036 will perform a clock error recovery sequence. If one or more of
the clock signals are absent, the TAS5036 is held with the outputs in hard mute until the clock is resumed.
Once the clock is resumed, the clock error recover sequence is completed.
Note. The detection of a clock error causes the TAS5036 to perform an immediate hard mute and suspension
of all processes. This abrupt transition can produce a faint click as the outputs are muted.
Since the clocks are removed when changing media or during input selection, it is possible to use this
knowledge to completely eliminate clicks in these conditions. In this case, the click is prevented by muting
the outputs by using the MUTE terminal or the I2C/MUTE command 43 ms in advance of the clocks being
removed.
In slave mode operation, when a crystal is connected to XTAL_IN and XTAL_OUT pins, the internal oscillator
of the TAS5036 is turned off.
In the slave mode, MCLK_OUT is driven low.
Table 2–2 shows all the possible master and slave modes. When operating in quad mode (Fs = 176.4 kHz
or 192 kHz), the device works in slave mode only with MCLK_IN = 128 Fs.
Table 2–3 shows the clocks speed for normal, double and quad modes.
8
TAS5036
SLES044B—November 2002
Architecture Overview
Table 2–2. Master and Slave Clock Modes
M_S
DBSPD
XTL_IN
(MHz)†
MCLK_IN
(MHz)‡
Internal PLL, master, normal speed
1
0
8.192
-
Internal PLL, master, normal speed
1
0
11.2896
Internal PLL, master, normal speed
1
0
12.288
DESCRIPTION
SCLK
(MHz)¶
LRCLK
(kHz)¶
MCLK_OUT
(MHz)#
2.048
32
8.192
-
2.8224
44.1
11.2896
-
3.072
48
12.288
5.6448
88.2
22.5792
6.144
96
24.576
22.5792
Internal PLL, master, double speed
1
1
-
Internal PLL, master, double speed
1
1
-
22.5792§
24.576§
Internal PLL, master, quad speed
1
0
-
22.5792
11.2896
176.4
Internal PLL, master, quad speed
1
0
-
24.576
12.288
192
24.576
Internal PLL, slave, normal speed
0
0
-
2.0484
32
Digital GND
Internal PLL, slave, normal speed
0
0
-
8.192§
11.2896§
2.8224
44.1
Digital GND
Internal PLL, slave, normal speed
0
0
-
12.288§
3.072
48
Digital GND
Internal PLL, slave, double speed
0
1
-
22.5792
5.6448
88.2
Digital GND
Internal PLL, slave, double speed
Internal PLL, slave, quad speed ||
0
1
-
96
Digital GND
0
-
24.576§
22.5792§
6.144
0
11.2896
176
Digital GND
Internal PLL, slave, quad speed ||
0
0
-
24.576§
12.288
192
Digital GND
External PLL, master, normal speed
1
0
-
-
2.048
32
8.192
External PLL, master, normal speed
1
0
-
-
2.8224
44.1
11.2896
External PLL, master, normal speed
1
0
-
-
3.072
48
12.288
External PLL, master, double speed
1
1
-
-
5.6448
88.2
22.5792
External PLL, master, double speed
1
1
-
-
6.144
96
24.576
External PLL, master, quad speed
1
0
-
-
11.2896
176.4
22.5792
External PLL, master, quad speed
1
0
-
-
12.288
192
24.576
External PLL, slave, normal speed
0
0
-
32
Digital GND
0
0
-
8.192§
11.2896§
2.0484
External PLL, slave, normal speed
2.8224
44.1
Digital GND
External PLL, slave, normal speed
0
0
-
12.288§
3.072
48
Digital GND
External PLL, slave, double speed
0
1
-
22.5792
5.6448
88.2
Digital GND
External PLL, slave, double speed
External PLL, slave, quad speed ||
0
1
-
6.144
96
Digital GND
0
0
-
24.576§
22.5792§
11.2896
176
Digital GND
0
0
24.576§
12.288
† A crystal oscillator is connected to XTL_IN.
‡ MCLK_IN tied low when input to XTL_IN is provided; XTL_IN tied low when MCLK_IN_IN is provided.
§ External MCLK_IN connected to MCLK_IN_IN input
¶ SCLK and LRCLK are outputs when M_S=1, and inputs when M_S=0.
# MCLK_OUT is driven low when M_S=0.
|| Quad-speed mode is detected automatically.
k SCLK can be 48 or 64 times Fs
192
Digital GND
External PLL, slave, quad speed ||
Table 2–3. LRCLK, MCLK_IN, and External PLL Rates
NORMAL SPEED (kHz)
LRCLK
1FS
32
DOUBLE SPEED (kHz)
44.1
48
QUAD SPEED (kHz)
1FS
64
88.2
96
1FS
176.4
192
MCLK_IN
256FS
8,192
11,289.6
12,288
256FS
16,384
22,579.2
24,576
128FS
22,579.2
24,576
EXT. PLL
2048FS
65,536
90,316.8
98,304
1024FS
65,536
90,316.8
98,304
512FS
90,316.8
98,304
SLES044B—November 2002
TAS5036
9
Architecture Overview
2.1.5 PLL Filter
A low jitter PLL produces the internal timing of the TAS5036 (when in master mode), the master clock, SCLK,
and LRCLK. Connections for the PLL external loop filter are provided through PLL_FLT_OUT and
PLL_FLT_RET as shown in Figure 2–2.
PLL_FLT_OUT
220 Ω
TAS5036
4.7 nF
47 nF
PLL_FLT_RET
Figure 2–2. External PLL Loop Filter
2.1.6 DCLK
DCLK is the internal high frequency clock that is produced by the PLL circuitry from MCLK. The TAS5036A
uses the DCLK to control all internal operations. DCLK is 8 times the speed of MCLK in normal speed mode,
4 times MCLK in double speed, and 2 times MCLK in quad speed. With respect to the I2C addressable
registers, DCLK clock cycles are used to specify Interchannel delay and to detect when the MCLK is frequency
is drifting. Table 2–4 DCLK shows the relationship between Sample Rate, MCLK and DCLK.
Table 2–4. DCLK
FS
(kHz)
MCLK
(MHz)
DCLK
(MHz)
DCK Period
(ns)
15.3
32
8.1920
65.5360
44.1
11.2896
90.3168
11.1
48
12.2880
98.3040
10.2
88
22.5280
90.1120
11.1
96
24.5760
98.3040
10.2
192
49.1520
98.3040
10.2
2.1.7 Serial Data Interface
The TAS5036 operates as a slave only/receive only serial data interface in all modes. The TAS5036 has three
PCM serial data interfaces to accept six channels of digital data though the SDIN1, SDIN2, SDIN3 inputs. The
serial audio data is in MSB first; 2s complement format.
The serial data interfaces of the TAS5036 can be configured in right justified, I2S, left-justified, or DSP modes.
This interface supports 32-kHz, 44.1-kHz, 48-kHz, 88-kHz, 96-kHz, 176.4-kHz, and 192-kHz data sample
rates. The serial data interface format is specified using the data interface control register. The supported word
lengths are shown in Table 2–5.
During normal operating conditions if the serial data interface settings change state, an error recovery
sequence is initiated.
10
TAS5036
SLES044B—November 2002
Architecture Overview
Table 2–5. Supported Word Lengths
2.1.7.1
DATA MODES
WORD
LENGTHS
MOD2
MOD1
MOD0
Right justified, MSB first
16
0
0
0
Right justified, MSB first
20
0
0
1
Right justified, MSB first
I2S
24
0
1
0
16
0
1
1
I2S
I2S
20
1
0
0
24
1
0
1
Left justified, MSB first
24
1
1
0
DSP frame
16
1
1
1
I2S Timing
I2S timing uses an LRCLK to define when the data being transmitted is for the left channel or the right channel.
The LRCLK is low for the left channel and high for the right channel. A bit clock running at 48 or 64 times Fs
is used to clock in the data. There is a delay of one bit clock from the time the LRCLK signal changes state
to the first bit of data on the data lines. The data is written MSB first and is valid on the rising edge of the bit
clock. The TAS5036 masks unused trailing data bit positions. Master mode only supports a 64 times Fs bit
clock.
2-Channel I2S (Philips Format) Stereo Input
32 Clks
LRCLK (Note Reversed Phase)
32 Clks
Left Channel
Right Channel
SCLK
SCLK
MSB
24-Bit Mode
23 22
LSB
9
8
5
4
5
4
1
0
1
0
1
0
MSB
LSB
23 22
9
8
5
4
19 18
5
4
1
0
15 14
1
0
1
0
20-Bit Mode
19 18
16-Bit Mode
15 14
Figure 2–3. I2S 64-Fs Format
SLES044B—November 2002
TAS5036
11
Architecture Overview
2-Channel I2S Stereo Input/Output (24-Bit Transfer Word Size)
24 Clks
24 Clks
LRCLK
Right Channel
Left Channel
SCLK
SCLK
MSB
24-Bit Mode
LSB
23 22 21 20 19
8
7
5
4
5
4
1
0
1
0
3
2
1
MSB
0
LSB
23 22 21 20 19
8
7
5
4
19 18 17 16 15
5
4
1
0
11
1
0
3
2
1
20-Bit Mode
19 18 17 16 15
16-Bit Mode
15 14 13 12
11
15 14 13 12
Figure 2–4. I2S 48-Fs Format
2.1.7.2
Left-Justified Timing
Left-justified (LJ) timing uses an LRCLK to define when the data being transmitted is for the left channel and
the right channel. The LRCLK is high for the left channel and low for the right channel. A bit clock running at
48 or 64 times Fs is used to clock in the data. The first bit of data appears on the data lines at the same time
the LRCLK toggles. The data is written MSB first and is valid on the rising edge of the bit clock. The TAS5036
masks unused trailing data bit positions. Master mode only supports a 64 times Fs bit clock.
2-Channel Left-Justified Stereo Input
32 Clks
32 Clks
LRCLK
LRCLK
Right Channel
Left Channel
SCLK
MSB
24-Bit Mode
23 22
LSB
9
8
5
4
1
0
MSB
23 22
LSB
9
8
5
4
1
0
NOTE: All data presented in 2s complement form with MSB first.
Figure 2–5. Left-Justified 64-Fs Format
12
TAS5036
SLES044B—November 2002
Architecture Overview
2-Channel Left-Justified Stereo Input/Output (24-Bit Transfer Word Size)
24 Clks
24 Clks
LRCLK
Right Channel
Left Channel
SCLK
MSB
24-Bit Mode
LSB
23 22 21 20 19
9
8
5
4
3
2
1
0
MSB
LSB
23 22 21 20 19
9
8
5
4
3
2
1
0
Figure 2–6. Left-Justified 48-Fs Format
2.1.7.3
Right-Justified Timing
Right-justified (RJ) timing uses an LRCLK to define when the data being transmitted is for the left channel and
the right channel. The LRCLK is high for the left channel and low for the right channel. A bit clock running at
48 or 64 times Fs is used to clock in the data. The first bit of data appears on the data 8-bit clock periods (for
24-bit data) after LRCLK toggles. In RJ mode, the last bit clock before LRCLK transitions always clocks the
LSB of data. The data is written MSB first and is valid on the rising edge of bit clock. The TAS5036 masks
unused leading data bit positions. Master mode only supports a 64 times Fs bit clock.
2-Channel Right-Justified (Sony Format) Stereo Input
32 Clks
32 Clks
LRCLK
Right Channel
Left Channel
SCLK
MSB
24-Bit Mode
LSB
23 22
19 18
15 14
1
0
19 18
15 14
1
0
15 14
1
0
MSB
LSB
23 22
19 18
15 14
1
0
19 18
15 14
1
0
15 14
1
0
20-Bit Mode
16-Bit Mode
NOTE: All data presented in 2s complement form with MSB first.
Figure 2–7. Right-Justified 64-Fs Format
SLES044B—November 2002
TAS5036
13
Architecture Overview
2-Channel Right-Justified Stereo Input/Output (24-Bit Transfer Word Size)
24 Clks
24 Clks
LRCLK
Right Channel
Left Channel
SCLK
MSB
24-Bit Mode
LSB
23 22 21 20 19 18
MSB
LSB
15 14
9
8
1
0
23 22 21 20 19 18
15 14
9
8
1
0
15 14
9
8
1
0
19 18
15 14
9
8
1
0
15 14
9
8
1
0
15 14
9
8
1
0
20-Bit Mode
19 18
16-Bit Mode
NOTE: All data presented in 2s complement form with MSB first.
Figure 2–8. Right-Justified 48-Fs Format
2.1.7.4
DSP Mode Timing
DSP mode timing uses an LRCLK to define when data is to be transmitted for both channels. A bit clock running
at 64 × Fs is used to clock in the data. The first bit of the left channel data appears on the data lines following
the LRCLK transition. The data is written MSB first and is valid on the rising edge of the bit clock. The TAS5036
masks unused trailing data bit positions.
SCLK
64 SCLKS
LRCLK
MSB
LSB
MSB
LSB
SDIN
16 Bits
Left
Channel
16 Bits
Right
Channel
32 Bits Unused
Figure 2–9. DSP Format
14
TAS5036
SLES044B—November 2002
Architecture Overview
2.2
Reset, Power Down, and Status
The reset, power down, and status circuitry provides the necessary controls to bring the TAS5036 to the initial
inactive condition, achieve low power standby, and report system status.
2.2.1 Reset—RESET
The TAS5036 is placed in the reset mode by setting the RESET terminal low.
RESET is an asynchronous control signal that restores the TAS5036 to its default conditions, sets the valid
1–6 outputs low, and places the PWM in the hard mute state. Volume is immediately set to full attenuation
(there is no ramp down).
As long as the RESET terminal is held low, the device is in the reset state. During reset, all I2C and serial data
bus operations are ignored. Table 2–6 shows the device output signals while RESET is active.
Upon the release of RESET, if POWER_DWN is high, the system performs a 4-ms to 5-ms device initialization
and then ramps the volume up to 0 db using a soft volume update sequence. If MCLK_IN is not active when
RESET is released high, then a 4-ms to 5-ms initialization sequence is produced once MCLK_IN becomes
active.
During device initialization all controls are reset to their initial states. Table 2–7 shows the control settings that
are changed during initialization.
RESET should be applied during power-up initialization or while changing the master slave clock states.
Table 2–6. Device Outputs During Reset
SIGNAL
MODE
SIGNAL STATE
Valid 1–Valid 6
All
Low
PWM P-outputs
All
Low
PWM M-outputs
All
Low
All
Low
MCLKOUT
SCLK
Master
Low
SCLK
Slave
Signal input
LRCLK
Master
Low
LRCLK
Slave
Signal input
SDA
All
Signal input
CLIP
All
High
Because the RESET is an asynchronous control signal, small clicks and pops can be produced during the
application (the leading edge) of this control. However, when RESET is released, the transition from the hard
mute state back to normal operation is performed synchronously using a quiet sequence.
If a completely quiet reset sequence is desired, MUTE should be applied before applying RESET.
Table 2–7. Values Set During Reset
CONTROL
SETTING
Volume
0 dB
MCLK_IN frequency
256
Master/slave mode
M_S terminal state
Auto mute
Enabled
De-emphasis
None
DC offset
0
Interchannel delay
Each channel set at 16 clocks higher then preceding channel
SLES044B—November 2002
TAS5036
15
Architecture Overview
2.2.2 Power Down—PDN
The TAS5036 can be placed into the power-down mode by holding the PDN terminal low. When power-down
mode is entered, both the PLL and the oscillator are shut down. Volume is immediately set to full attenuation
(there is no ramp down). The valid 1–6 outputs are immediately asserted low and the PWM outputs are placed
in the hard mute state. PDN initiates device power down without clock inputs. As long as the PDN terminal
is held low—the device is in the power-down (hard mute) state.
During power down, all I2C and serial data bus operations are ignored. Table 2–8 shows the device output
signals while PDN is active.
Table 2–8. Device Outputs During Power Down
SIGNAL
MODE
SIGNAL STATE
Valid 1–Valid 6
All
Low
PWM P-outputs
All
Low
PWM M-outputs
All
Low
MCLKOUT
All
Low
Master
Low
SCLK
Slave
Signal input
LRCLK
Master
Low
LRCLK
Slave
Signal input
SDA
All
Signal input
CLIP
All
High
SCLK
To place the device in total power-down mode, both RESET and power-down modes must be enabled. Prior
to bringing PDN high, RESET must be brought low for a minimum of 50 ns.
Because PDN is an asynchronous control signal, small clicks and pops can be produced during the application
(the leading edge) of this control. However, when PDN is released, the transition from the hard mute state back
to normal operation is performed synchronously using a quiet sequence.
If a completely quiet reset sequence is desired, MUTE should be applied before applying PDN.
2.2.2.1
Recovery Time Options
To support the requirements of various system configurations, the TAS5036 can come up to the normal state
after either a long (100 ms) or a short (5 ms) delay.
1. In the first case, a slow system (95 ms to 100 ms) start-up occurs at the end of the power-down sequence
when:
RESET is high for at least 16 MCLK_IN periods before PDN goes high.
2. Otherwise a fast (4 ms to 5 ms) start up occurs.
NOTE: If MCLK_IN is not active when both of these signals are released high, then a a fast
(4 ms to 5 ms) start up occurs once MCLK_IN becomes active.
2.2.3 Status Registers
The TAS5036 provides device identification and operational status information that is accessible through the
serial control interface status registers that provide general device information.
Device ID—The TAS5036 provides a device identification code that is accessible through the serial control
interface
Volume Update is in Progress—Whenever a volume change is in progress, this status bit is high.
No Internal Errors (All Valid Signals are High)—When there are no internal errors in the TAS5036 and all
outputs are valid, this status bit is high.
LRCLK Error—When there are the MCLK_IN rate changes more than ±10 MCLK_IN cycles from the correct
number of cycles (128 or 256) per LRCLK cycle
MCLK_IN Error—When the MCLK_IN frequency changes such that it is out of synchronization with internal
PLL generated clock
16
TAS5036
SLES044B—November 2002
Architecture Overview
2.3
Signal Processing
This section contains the signal processing functions that are contained in the TAS5036. The signal
processing is performed using a high-speed 24-bit signal processing architecture. The TAS5036 performs the
following signal processing features:
• Individual channel soft volume with a range of 24 dB to –114 dB plus mute
• Soft mute
• Auto mute
• 50-µs/15-µs de-emphasis filter supported in the sampling rates 32 kHz, 44.1 kHz, and 48 kHz
2.3.1 Volume Control
The gain of each output can be adjusted by a soft digital volume control for each channel. Volume adjustments
are performed using a soft gain update s-curve, which is approximated using a second order filter fit. The curve
fit is performed over a transition interval between 41 ms and 65 ms.
The volume of each channel can be adjusted from mute to 24 dB to –114 dB in 0.5 dB steps. Because of the
numerical representation that is used to control the volume, at very low volume levels the step size increases
for gains of that are less than –96 dB. The default volume setting following power up or reset is 0 dB for all
channels. The step size increases linearly up to approximately –90 dB, see Figure 2–10.
STEP SIZE
vs
ATTENUATION (GAIN)
6.0
5.5
5.0
4.5
Step Size – dB
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
–110
–100
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
10
20
Attenuation (Gain) – dB
Figure 2–10. Attenuation Curve
The volume control format for each channel is expressed in 8 bits. The volume for each channel is set by writing
8 bits via the serial control interface. The MSB bit is written first as in the bit position 0 (LSB position).
The volume for each channel can be set using a single or multiple address write operation to the volume control
register via the serial control interface. To change the volume of all six channels requires that 6 registers be
updated.
To coordinate the volume adjustment of multiple channels simultaneously, the TAS5036 performs a delayed
volume update upon receiving a volume change command. Following the completion of the register volume
write operations, the TAS5036 waits for 5 ms for another volume command to be given. If no volume command
is issued in that period of time, the TAS5036 starts adjusting the volume of the channels that received volume
settings.
SLES044B—November 2002
TAS5036
17
Architecture Overview
While a volume update is being performed, the system status register indicates that the update is in progress.
During the update, all subsequent volume control setting requests that are sent to the TAS5036 are received
and stored as a single next value for a subsequent update. If more than one volume setting request is sent,
only the last is retained.
Table 2–9. Volume Register
VOLUME REGISTER
D7
D6
D5
D4
D3
D2
D1
D0
Vol
Vol
Vol
Vol
Vol
Vol
Vol
Vol
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
2.3.2 Mute
The application of mute ramps the volume from any setting to noiseless hard mute state. There are two
methods in which the TAS5036 can be placed into mute. The TAS5036 is placed in the noiseless mute when
the MUTE terminal is asserted low for a minimum of 3 MCLK_IN cycles. Alternatively, the mute mode can be
initiated by setting the mute bit in the system control register through the serial control interface. The TAS5036
is held in mute state as long as the terminal is low or I2C mute setting is active. This command uses quiet entry
and exit sequences to and from the hard mute state.
If an error recovery (described in the PWM section) occurs after a mute request has been received, the device
returns from error recovery with the channel volume set as specified by the mute command.
2.3.3 Auto Mute
Auto mute is an automatic sequence that can be enabled or disabled via the serial control interface. The
default for this control is enabled. When enabled, the PWM auto mutes an individual channel when a channel
receives from 5 ms to 50 ms of consecutive zeros. This time interval can be selectable using the auto mute
delay register. The default interval is 5 ms at 48 kHz. This duration is independent of the sample rate. The auto
mute state is exited when two consecutive samples of nonzero data are received.
This mode uses the valid low to provide a low-noise floor while maintaining a short startup time. Noise free
entry and exit is achieved by using the PWM quiet start and stop sequences.
2.3.4 Individual Channel Mute
Individual channel mute is invoked through the serial interface. Individual channel mute permits each channel
of the TAS5036 to be individually muted and unmuted. The operation that is performed is identical to the mute
operation; however, it is performed on a per channel basis. A TAS5036 channel is held in the mute state as
long as the serial interface mute setting for that channel is set.
2.3.5 De-Emphasis Filter
For audio sources that have been pre-emphasized, a precision 50-µs/15-µs de-emphasis filter is provided to
support the sampling rates of 32 kHz, 44.1 kHz, and 48 kHz. See Figure 2–11 for a graph showing the
de-emphasis filtering characteristics. De-emphasis is set using two bits in the system control register.
Table 2–10. De-Emphasis Filter Characteristics
DEM_SEL2 (MSB)
DEM_SEL1
0
0
De-emphasis disabled
DESCRIPTION
0
1
De-emphasis enabled for Fs = 48 kHz
1
0
De-emphasis enabled for Fs = 44 kHz
1
1
De-emphasis enabled for Fs = 32 kHz
Following the change of state of the de-emphasis bits, the PWM outputs go into the soft mute state. After 128
LRCLK periods for initialization, the PWM outputs are driven to the normal (unmuted) mode.
18
TAS5036
SLES044B—November 2002
Response – dB
Architecture Overview
0
De-Emphasis
–10
3.18 (50 µs)
10.6 (15 µs)
f – Frequency – kHz
Figure 2–11. De-Emphasis Filter Characteristics
2.4
Pulse Width Modulator (PWM)
The TAS5036 contains six channels of high performance digital Equibit PWM modulators that are designed
to drive switching output stages (back ends) in both single-ended (SE) and H-bridge (bridge tied load)
configuration. The TAS5036 device uses noise shaping and sophisticated error correction algorithms to
achieve high power efficiency and high-performance digital audio reproduction.
The PWM provides six pseudo-differential outputs to drive six monolithic power stages (such as TAS5110)
or six discrete differential power stages using gate drivers (such as the TAS5182) and MOSFETs in
single-ended or bridged configurations. The TAS5036 also provides a high performance differential output that
can be used to drive an external analog headphone amplifier.
2.4.1 Clipping Indicator
The clipping output is designed to indicate clipping. When any of the six PWM outputs exceeds the maximum
allowable amplitude, the clipping indicator is asserted. The clipping indicator is cleared every 10 ms.
2.4.2 Error Recovery
Error recovery is used to provide error management and to permit the PWM output to be reset while preserving
all inter-volume, inter-channel delay, dc offsets, and the other internal settings. Error recovery is initiated by
bringing the /ERR_RCVRY terminal low for a minimum 5 MCLK_IN cycles or by setting the error recovery bit
in control register 1. Error recovery is a level sensitive signal.
The device also performs an error recovery automatically:
•
When the speed configuration is changed to normal, double, or quad speed
•
Following a change in the serial data bus interface configuration
When ERR_RCVRY is brought low, all valid signals go low, and the PWM-P and PWM-M outputs go low. If
there are any pending speed configurations, these changes are then performed. When ERR_RCVRY is
brought high, a delay of 4 ms to 5 ms is performed before the system starts the output re-initialization
sequence. After the initialization time, the TAS5036 begins normal operation. During error recovery, all
controls and device settings that were not updated are maintained in their current configurations.
To permit error recovery to be used to provide TAS5100 error management and recovery, the delay between
the start of (falling edge) error recovery and the falling edge of valid 1 though valid 6 is selectable. This delay
can be selected to be either 6 µs or 47 µs.
During error recovery all serial data bus operations are ignored. At the conclusion of the sequence, the error
recovery register bit is returned to normal operation state. Table 2–11 shows the device output signal states
while during error recovery.
SLES044B—November 2002
TAS5036
19
Architecture Overview
Table 2–11. Device Outputs During Error Recovery
SIGNAL
MODE
SIGNAL STATE
Valid 1–Valid 6
All
Low
PWM P-outputs
All
Low
PWM M-outputs
All
Low
MCLKOUT
All
Low
Master
Low
SCLK
Slave
Signal input
LRCLK
Master
Low
LRCLK
Slave
Signal input
SDA
All
Signal input
CLIP
All
High
SCLK
The transitions are done using a quiet entrance and exit sequence to prevent pops and clicks.
2.4.3 Individual Channel Error Recovery
Individual channel error recovery is used to provide error management and to permit the PWM output to be
turned off. Error recovery is initiated by setting one or more of the six error recovery bits in the error recovery
register to low.
While the error recover bits are brought low, the valid signals goes to the low state. When the error recovery
bits are brought high, a delay of 4 ms to 5 ms occurs before the channels are returned to normal operation.
The delay between the falling edge of the error recover bit and the falling edge of valid 1 though valid 6 is
selectable. This delay can be selected to be either 6 µs or 47 µs.
The TAS5036 controls the relative timing of the pseudo-differential drive control signals plus the valid signal
to minimize the production of system noise during error recovery operations. The transitions to valid low and
valid high are done using an almost quiet entrance and exit sequence to prevent pops and clicks.
2.4.4 PWM DC-Offset Correction
An 8-bit value can be programmed to each of the six PWM offset correction registers to correct for any offset
present in the output stages. The offset correction is divided into 256 intervals with a total offset correction of
±1.56% of full scale. The default value is zero correction represented by 00 (hex). These values can be
changed at any time through the serial control interface.
2.4.5 Inter-Channel Delay
An 8-bit value can be programmed to each of the six PWM inter-channel delay registers to add a delay per
channel from 0 to 255 clock cycles. The delays correspond to cycles of the high-speed internal clock, DCLK
(or alternatively the external PLL clock frequency). Each subsequent channel has a default value that is N
DCLKs larger than the preceding channel. The default values are 0 for the first channel and 16 for each
successive channel.
These values can be updated upon power up through the serial control interface. This delay is generated in
the PWM block with the appropriate control signals generated in the CTL block.
These values can be changed at any time through the serial control interface. The optimum performance of
the TAS5036 can be achieved using an interchannel delay of 21.
2.4.6 ABD Delay
A 5-bit value is used to delay the A PWM signals with respect to B PWM signals. The value is the same for
all channels. It can be programmed from 0 to 31 DCLK clock cycles. The default values is 11 DCLK clock cycles
(01011). This value is mask programmable. These values can be changed at any time through the serial
control interface.
The optimum performance of the TAS5036 can be achieved with an ABD delay of 30.
20
TAS5036
SLES044B—November 2002
Architecture Overview
2.4.7 PWM/H-Bridge and Discrete H-Bridge Driver Interface
The TAS5036 provides six PWM outputs, which are designed to drive switching output stages (back-ends)
in both single-ended (SE) and H-bridge (bridge tied load) configuration. The back-ends may be monolithic
power stages (such as the TAS5110) or six discrete differential power stages using gate drivers (such as the
the TAS55182) and MOSFETs in single-ended or bridged configurations.
The TAS5110 device is optimised for bridge tied load (BTL) configurations. These devices require a pure
differential PWM signal with a third signal (VALID) to control the MUTE state. In the MUTE state, the TAS5110
OUTA and OUTB are both low.
One Channel
of TAS5036
TAS5110
PWM_AP
AP
PWM_AM
AM
VALID
OUTA
Speaker
RESET
BP
BM
OUTB
Figure 2–12. PWM Outputs and H-Bridge Driven in BTL Configuration
2.5
I2C Serial Control Interface
The TAS5036 has a bidirectional serial control interface that is compatible with the I2C (Inter IC) bus protocol
and supports both 100 KBPS and 400 KBPS data transfer rates for single and multiple byte write and read
operations. This is a slave only device that does not support a multi-master bus environment or wait state
insertion. The control interface is used to program the registers of the device and to read device status.
The TAS5036 supports the standard-mode I2C bus operation (100 kHz maximum) and the fast I2C bus
operation (400 kHz maximum). The TAS5036 performs all I2C operations without I2C wait cycles.
The I2C bus employs two signals; SDA (data) and SCL (clock), to communicate between integrated circuits
in a system. Data is transferred on the bus serially one bit at a time. The address and data are transferred in
byte (8 bit) format with the most significant bit (MSB) transferred first. In addition, each byte transferred on the
bus is acknowledged by the receiving device with an acknowledge bit. Each transfer operation begins with
the master device driving a start condition on the bus and ends with the master device driving a stop condition
on the bus. The bus uses transitions on the data terminal (SDA) while the clock is high to indicate a start and
stop conditions. A high-to-low transition on SDA indicates a start, and a low-to-high transition indicates a stop.
Normal data bit transitions must occur within the low time of the clock period. These conditions are shown in
Figure 2–13. The master generates the 7-bit slave address and the read/write (R/W) bit to open
communication with another device and then waits for an acknowledge condition. The TAS5036 holds SDA
low during acknowledge clock period to indicate an acknowledgement. When this occurs, the master transmits
the next byte of the sequence. Each device is addressed by a unique 7-bit slave address plus R/W bit (1 byte).
All compatible devices share the same signals via a bidirectional bus using a wired-AND connection. I2C An
external pullup resistor must be used for the SDA and SCL signals to set the high level for the bus.
SLES044B—November 2002
TAS5036
21
Architecture Overview
7 Bit Slave Address
SDA
7 6
5
4
3
2
R/W
1 0
A
8 Bit Register Address (N)
7 6
5
4
3
2
A
1 0
8 Bit Register Data For
Address (N)
7 6
5
4
3
2
A
1 0
8 Bit Register Data For
Address (N)
7 6
5
4
3
2
A
1 0
SCL
Start
Stop
Figure 2–13. Typical I2C Sequence
There are no limits on the number of bytes that can be transmitted between start and stop conditions. When
the last word transfers, the master generates a stop condition to release the bus. A generic data transfer
sequence is also shown in Figure 2–13.
The 7-bit address for the TAS5036 is 001101X, where X is a programmable address bit. Using the CS0
terminal on the device, the LSB address bit is programmable to permit two devices to be used in a system.
These two addresses are licensed I2C addresses and do not conflict with other licensed I2C audio devices.
To communicate with the TAS5036, the I2C master uses 0011010 if CS0=0 and 0011011 if CS0=1. In addition
to the 7-bit device address, an 8-bit register address is used to direct communication to the proper register
location within the device interface.
Read and write operations to the TAS5036 can be done using single byte or multiple byte data transfers.
2.5.1 Single Byte Write
As shown in Figure 2–14, a single byte data write transfer begins with the master device transmitting a start
condition followed by the I2C device address and the read/write bit. The read/write bit determines the direction
of the data transfer. For a write data transfer, the read/write bit is 0. After receiving the correct I2C device
address and the read/write bit, the TAS5036 device responds with an acknowledge bit. Next, the master
transmits the address byte or bytes corresponding to the TAS5036 internal memory address being accessed.
After receiving the address byte, the TAS5036 again responds with an acknowledge bit. Next, the master
device transmits the data byte to be written to the memory address being accessed. After receiving the data
byte, the TAS5036 again responds with an acknowledge bit. Finally, the master device transmits a stop
condition to complete the single byte data write transfer.
Acknowledge
Start Condition
A6
A5
A4
A3
A2
A1
I2C Device Address and
Read/Write Bit
A0 R/W ACK A7
Acknowledge
A6
A5
A4
A3
A2
A1
A0 ACK D7
Register Address
Acknowledge
D6
D5
D4
D3
Data Byte
D2
D1
D0 ACK
Stop
Condition
Figure 2–14. Single Byte Write Transfer
2.5.2 Multiple Byte Write
A multiple byte data write transfer is identical to a single byte data write transfer except that multiple data bytes
are transmitted by the master device to TAS5036 as shown in Figure 2–15. After receiving each data byte,
the TAS5036 responds with an acknowledge bit.
22
TAS5036
SLES044B—November 2002
Architecture Overview
Acknowledge
Start Condition
A6
A5
A1
Acknowledge
A0 R/W ACK A7
A6
I2C Device Address and
Read/Write Bit
A5
A4
A3
A1
A0 ACK D7
Register Address
Acknowledge
Acknowledge
D6
D1
D0 ACK
D7
Other
Data Bytes
First Data Byte
D6
D1
D0 ACK
Stop
Condition
Last Data Byte
Figure 2–15. Multiple Byte Write Transfer
2.5.3 Single Byte Read
As shown in Figure 2–16, a single byte data read transfer begins with the master device transmitting a start
condition followed by the I2C device address and the read/write bit. For the data read transfer, a write followed
by a read are actually done. Initially, a write is done to transfer the address byte or bytes of the internal memory
address to be read. As a result, the read/write bit is 0. After receiving the TAS5036 address and the read/write
bit, the TAS5036 responds with an acknowledge bit. Also, after sending the internal memory address byte or
bytes, the master device transmits another start condition followed by the TAS5036 address and the read/write
bit again. This time the read/write bit is a 1 indicating a read transfer. After receiving the TAS5036 and the
read/write bit, the TAS5036 again responds with an acknowledge bit. Next, the TAS5036 transmits the data
byte from the memory address being read. After receiving the data byte, the master device transmits a not
acknowledge followed by a stop condition to complete the single byte data read transfer.
Repeat Start Condition
Start
Condition
Acknowledge
A6
A5
A1
A0 R/W ACK A7
I2C Device Address and
Read/Write Bit
Acknowledge
A6
A5
A4
A0 ACK
A6
A5
A1
A0 R/W ACK D7
I2C Device Address and
Read/Write Bit
Register Address
Not
Acknowledge
Acknowledge
D6
D1
D0 ACK
Stop
Condition
Data Byte
Figure 2–16. Single Byte Read
2.5.4 Multiple Byte Read
A multiple byte data read transfer is identical to a single byte data read transfer except that multiple data bytes
are transmitted by the TAS5036 to the master device as shown in Figure 2–17. Except for the last data byte,
the master device responds with an acknowledge bit after receiving each data byte.
Repeat Start
Condition
Start
Condition
Acknowledge
A6
A0 R/W ACK A7
I2C Device Address and
Read/Write Bit
Acknowledge
A6
A5
A4
A0 ACK
Register Address
Acknowledge
A6
A0 R/W ACK D7
I2C Device Address and
Read/Write Bit
Not
Acknowledge
Acknowledge
D0 ACK
First Data Byte
D7
Other
Data Bytes
D6
D1
D0 ACK
Last Data Byte
Stop
Condition
Figure 2–17. Multiple Byte Read
SLES044B—November 2002
TAS5036
23
Serial Control Interface Register Definitions
3
Serial Control Interface Register Definitions
Table 3–1 shows the register map for the TAS5036. Default values in this section are in bold.
Table 3–1. I2C Register Map
ADDR HEX
DESCRIPTION
00
General status register
01
Error status register
02
System control register 0
03
System control register 1
04
Error recovery register
05
Automute delay
06
DC-offset control register channel 1
07
DC-offset control register channel 2
08
DC-offset control register channel 3
09
DC-offset control register channel 4
0A
DC-offset control register channel 5
0B
DC-offset control register channel 6
0C
Interchannel delay register channel 1
0D
Interchannel delay register channel 2
0E
Interchannel delay register channel 3
0F
Interchannel delay register channel 4
10
Interchannel delay register channel 5
11
Interchannel delay register channel 6
12
ABD delay register
13
Volume control register channel 1
14
Volume control register channel 2
15
Volume control register channel 3
16
Volume control register channel 4
17
Volume control register channel 5
18
Volume control register channel 6
19
Individual channel mute
The volume table is contained in Appendix A.
Default values are shown in bold in the following tables
NOTE:
The performance of a TDAA system is optimized by setting the PWM timing based upon the
type of back-end device that is used and, to a lesser extent, the layout. These values are set
during initialization using the I2C serial interface. The specific timing parameter values for each
PWM and back-end configuration is contained in the EVM User Manual, Reference Design
User Manual, and design application note for these devices. Please refer to the appropriate
EVM User Manual, Reference Design user manual, or design application note for these
values.
24
TAS5036
SLES044B—November 2002
Serial Control Interface Register Definitions
3.1
General Status Register (x00)
Table 3–2. General Status Register (Read Only)
D7
D6
D5
D4
D3
D2
D1
D0
0
-
-
-
-
-
-
-
No volume update is in progress.
FUNCTION
1
-
-
-
-
-
-
-
Volume update is in progress.
-
0
-
-
-
-
-
-
Always 0
-
-
1
0
0
1
1
-
Device identification code
-
-
-
-
-
-
-
0
Any valid signal is inactive (see status register (X03)) (see Note 1).
-
-
-
-
-
-
-
1
No internal errors (all valid signals are high)
NOTE 1: This bit is reset automatically when all of the valid signals are active.
3.2
Error Status Register (x01)
Table 3–3. Error Status Register
D7
D6
D5
D4
D3
D2
D1
D0
FUNCTION
1
-
-
-
-
-
-
-
FS error has occurred
-
1
-
-
-
-
-
-
Control pin change has occurred
-
-
-
1
-
-
-
-
LRCLK error
-
-
-
-
1
-
-
-
MCLK_IN count error
-
-
-
-
-
1
-
-
DCLK phase error with respect to MCLK_IN
-
-
-
-
-
-
1
-
MCLK_IN phase error with respect to DCLK
-
-
-
-
-
-
-
1
PWM timing error
0
0
0
0
0
0
0
0
No errors—no control pins changed
NOTE 1: Write 00 hex to clear error indications in Error Status Register.
3.3
System Control Register 0 (x02)
Table 3–4. System Control Register 0
D7
D6
D5
D4
D3
D2
D1
D0
FUNCTION
0
0
-
-
-
-
-
-
Normal mode (in slave mode—quad speed detected if MCLK_IN = 128 Fs)
0
1
-
-
-
-
-
-
Double speed
1
0
-
-
-
-
-
-
Quad speed
1
1
-
-
-
-
-
-
Illegal
-
-
0
-
-
-
-
-
Use de-emphasis pin controls
-
-
1
-
-
-
-
-
Use de-emphasis I2C controls
-
-
-
0
0
-
-
-
No de-emphasis
-
-
-
0
1
-
-
-
De-emphasis for Fs = 32 kHz
-
-
-
1
0
-
-
-
De-emphasis for Fs = 44.1 kHz
-
-
-
1
1
-
-
-
De-emphasis for Fs = 48 kHz
-
-
-
-
-
0
0
0
16 bit, MSB first; right justified
-
-
-
-
-
0
0
1
20 bit, MSB first; right justified
-
-
-
-
-
0
1
0
24 bit, MSB first; right justified
-
-
-
-
-
0
1
1
16-bit IIS
-
-
-
-
-
1
0
0
20-bit IIS
-
-
-
-
-
1
0
1
24-bit IIS
-
-
-
-
-
1
1
0
16-bit MSB first
-
-
-
-
-
1
1
1
16-bit DSP Frame
SLES044B—November 2002
TAS5036
25
Serial Control Interface Register Definitions
3.4
System Control Register 1 (x03)
Table 3–5. System Control Register 1
D7
D6
D5
D4
D3
D2
D1
D0
0
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0
-
-
-
-
-
-
Valid remains high during auto mute.
-
1
-
-
-
-
-
-
Valid goes low during auto mute.
-
-
0
-
-
-
-
-
Valid remains high during mute.
-
-
1
-
-
-
-
-
Valid goes low during mute.
-
-
-
0
-
-
-
-
Mute
-
-
-
1
-
-
-
-
Normal mode
-
-
-
-
0
-
-
-
Set error recovery delay at 6 µs
-
-
-
-
1
-
-
-
Set error recovery delay at 47 µs
-
-
-
-
-
0
-
-
Error recovery (forces error recovery initialization sequence)
-
-
-
-
-
1
-
-
Normal mode
-
-
-
-
-
-
0
-
Auto mute disabled
-
-
-
-
-
-
1
-
Auto mute enabled
-
-
-
-
-
-
-
0
-
-
-
-
-
-
-
1
Normal mode
Resets all I2C registers to their default conditions
3.5
FUNCTION
UNUSED
Error Recovery Register (x04)
Table 3–6. Error Recovery Register
D7
D6
D5
D4
D3
D2
D1
D0
1
1
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0
-
-
-
-
-
Put channel 6 into error recovery mode
-
-
-
0
-
-
-
-
Put channel 5 into error recovery mode
-
-
-
-
0
-
-
-
Put channel 4 into error recovery mode
-
-
-
-
-
0
-
-
Put channel 3 into error recovery mode
-
-
-
-
-
-
0
-
Put channel 2 into error recovery mode
-
-
-
-
-
-
-
0
Put channel 1 into error recovery mode
-
-
1
1
1
1
1
1
Normal operation
3.6
FUNCTION
Unused
Automute Delay Register (x05)
Table 3–7. Automute Delay Register
D7
D6
D5
D4
D3
D2
D1
D0
0
0
0
0
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0
0
0
0
Set automute delay at 5 ms
-
-
-
-
0
0
0
1
Set automute delay at 10 ms
-
-
-
-
0
0
1
0
Set automute delay at 15 ms
-
-
-
-
0
0
1
1
Set automute delay at 20 ms
-
-
-
-
0
1
0
0
Set automute delay at 25 ms
-
-
-
-
0
1
0
1
Set automute delay at 30 ms
-
-
-
-
0
1
1
0
Set automute delay at 35 ms
-
-
-
-
0
1
1
1
Set automute delay at 40 ms
-
-
-
-
1
-
-
0
Set automute delay at 45 ms
-
-
-
-
1
-
-
1
Set automute delay at 50 ms
26
TAS5036
FUNCTION
Unused
SLES044B—November 2002
Serial Control Interface Register Definitions
3.7
DC-Offset Control Registers (x06–x0B)
Channels 1, 2, 3, 4, 5, and 6 are mapped into (x06, x07, x08, x09, x0A, and x0B).
Table 3–8. DC-Offset Control Registers
D7
D6
D5
D4
D3
D2
D1
D0
1
0
0
0
0
0
0
0
Maximum correction for positive dc offset (–1.56% FS)
0
0
0
0
0
0
0
0
No dc-offset correction
0
1
1
1
1
1
1
1
Maximum correction for negative dc offset (1.56% FS)
3.8
FUNCTION
Interchannel Delay Registers (x0C–x11)
Channels 1, 2, 3, 4, 5, and 6 are mapped into (x0C, x0D, x0E, x0F, x10, and x11).
The first channel delay is set at 0. Each subsequent channel has a default value that is 16 DCLKs larger than
the preceding channel.
Table 3–9. Six Inter-Channel Delay Registers
D7
D6
D5
D4
D3
D2
D1
D0
0
0
0
0
0
0
0
0
Minimum absolute delay, 0 DCLK cycles, default for channel 1
0
0
0
1
0
0
0
0
Default for channel 2
0
0
1
0
0
0
0
0
Default for channel 3
0
0
1
1
0
0
0
0
Default for channel 4
0
1
0
0
0
0
0
0
Default for channel 5
0
1
0
1
0
0
0
0
Default for channel 6
1
1
1
1
1
1
1
1
Maximum absolute delay, 255 DCLK cycles
3.9
FUNCTION
ABD Delay Register (x12)
Table 3–10. ABD Delay Register
D7
D6
D5
D4
D3
D2
D1
D0
0
0
0
-
-
-
-
-
FUNCTION
-
-
-
-
-
-
-
-
-
-
-
0
0
0
0
0
Minimum ABD delay, 0 DLCK cycles
-
-
-
0
1
0
1
1
Default ABD delay, 11 DLCK cycles
-
-
-
1
1
1
1
1
Maximum ABD delay, 31 DLCK cycles
Unused
3.10 Individual Channel Mute Register (x19)
Table 3–11. Individual Channel Mute Register
D7
D6
D5
D4
D3
D2
D1
D0
1
1
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
1
1
1
1
1
1
No channels are muted
-
-
-
-
-
-
-
0
Mute channel 1
-
-
-
-
-
-
0
-
Mute channel 2
-
-
-
-
-
0
-
-
Mute channel 3
-
-
-
-
0
-
-
-
Mute channel 4
-
-
-
0
-
-
-
-
Mute channel 5
-
-
0
-
-
-
-
-
Mute channel 6
SLES044B—November 2002
FUNCTION
Unused
TAS5036
27
System Initialization
4
System Initialization
Reset is used during system initialization to hold the TAS5036 inactive while power (VDD), the master clock
(MCLK_IN), the device control, and the data signals become stable. The recommended initialization
sequence is to hold RESET low for 24 MCLK_IN cycles after VDD has reached 3 V and the other control
signals (MUTE, PDN, M_S, ERR_RCVRY,, DBSPD, and CS0) are stable.
3V
VDD
RESET
24 MCLK_IN
Cycles
MCLK
Figure 4–1. RESET During System Initialization
The serial data interface format is then set through the serial data interface control register using the serial
control interface.
At this point the TAS5036 is fully operational. However, the operation of the TAS5036 can be tailored as
desired to meet specific operating requirements by adjusting the following:
28
•
Automute delay register
•
DC-Offset control registers
•
Interchannel delay registers
TAS5036
SLES044B—November 2002
Specifications
5
Specifications
5.1
Absolute Maximum Ratings Over Operating Temperature Ranges (Unless
Otherwise Noted)†
Digital supply voltage range: DVDD_CORE, DVDD_PWM, DVDD_RCL . . . . . . . . . . . . . . . . . . –0.3 V to 4.2 V
Analog supply voltage range: AVDD_PLL, ADD_OSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 4.2 V
Digital input voltage range, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to DVDDX + 0.3 V
Operating free-air temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 85°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
ESD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000 V
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
5.2
Recommended Operating Conditions (Fs = 48 kHz)
Supply voltage
Digital
Supply current
Digital
MIN
TYP
MAX
3
3.3
3.6
DVDDX, See Note 1
Operating
60
Power down, See Note 2
Power dissipation
Digital
Supply voltage
Analog
Supply current
Analog
200
Power down
3
Analog
3.6
10
Power down, See Note 2
35
Power down, See Note 2
µW
V
mA
25
Operating
Power dissipation
3.3
µA
mW
100
AVDDX, See Note 3
Operating
V
mA
25
Operating
UNIT
µA
mW
100
µW
NOTES: 2. DVDD_CORE, DVDD_PWM, DVDD_RCL
3. If the clocks are turned off.
4. AVDD_PLL, AVDD_OSC
5.3
Electrical Characteristics Over Recommended Operating Conditions (Unless
Otherwise Noted)
5.3.1
Static Digital Specifications Over Recommended Operating Conditions (Unless
Otherwise Noted)
MIN
MAX
VIH
VIL
High-level input voltage
PARAMETER
2
DVDD1
V
Low-level input voltage
0
0.8
V
VOH
VOL
High-level output voltage
Ilkg
Input leakage current
Low-level output voltage
5.3.2
TEST CONDITIONS
IO = –1 mA
IO = 4 mA
2.4
–10
UNIT
V
0.4
V
10
µA
Digital Interpolation Filter and PWM Modulator Over Recommended Operating
Conditions (Unless Otherwise Noted) Fs = 48 kHz
PARAMETER
TEST CONDITIONS
Pass band
MIN
0
Pass band ripple
Stop band
Stop band attenuation
TYP
24.1 kHz to 152.3 kHz
20
UNIT
kHz
±0.012
dB
24.1
kHz
50
dB
Group delay
700
PWM modulation index (gain)
0.93
SLES044B—November 2002
MAX
µs
TAS5036
29
Specifications
5.3.3
TAS5036/TAS5100 System Performance Measured at the Speaker Terminals
Over Recommended Operating Conditions (Unless Otherwise Noted)
Fs = 48 kHz; Input = 1 Vrms Sine Wave at 1 kHz
PARAMETER
TEST CONDITIONS
MIN
SNR (EIAJ)
A-weighted
Dynamic range
A-weighted, -60 dB, f = 1 kHz, 20 Hz–20 kHz
Signal to (noise + distortion) ratio
0 dB, 1 kHz, 20 Hz–20 kHz
Pad driver power supply rejection ratio
1 kHz
TYP
MAX
UNIT
93
dB
95
dB
0.08%
dB
Idle tone rejection
dB
Intermodulation distortion
dB
Frequency response
dB
Crosstalk
dB
Jitter tolerance
ps
PWM modulation index
5.4
0.93
Switching Characteristics
5.4.1
Command Sequence Timing
5.4.1.1
Reset Timing—RESET
CONTROL SIGNAL PARAMETERS OVER RECOMMENDED OPERATING CONDITIONS (UNLESS OTHERWISE NOTED)
PARAMETER
TEST CONDITIONS
tw(RESET)
Pulses duration, RESET active
tp(VALID_LOW)
tp(VALID_HIGH)
Propagation delay
td(VOLUME)
Delay time
MIN
TYP
MAX
50
Propagation delay
UNIT
ns
4
42
1
µs
5
ms
ms
RESET
tw(RESET)
VALID 1–6
VOLUME 1–6
tp(VALID_LOW)
td(VOLUME)
tp(VALID_HIGH)
Figure 5–1. RESET Timing
30
TAS5036
SLES044B—November 2002
Specifications
5.4.1.2
Power-Down Timing—PDN
5.4.1.2.1 Long Recovery
CONTROL SIGNAL PARAMETERS OVER RECOMMENDED OPERATING CONDITIONS (UNLESS OTHERWISE NOTED)
PARAMETER
tw(PDN)
Pulse duration, PDN active
td(R PDNR)
tp(VALID_LOW)
Reset high to PDN rising edge
TEST CONDITIONS
MIN
TYP
MAX
50
ns
16 MCLKS
tp(VALID_HIGH)
ns
85
td(VOLUME)
UNIT
1
µs
100
ms
42
ms
td(R PDNR)
RESET
PDN
tw(PDN)
VALID 1–6
VOLUME 1–6
Normal
Operation
Normal
Operation
tp(VALID_HIGH)
tp(VALID_LOW)
td(VOLUME)
Figure 5–2. Power-Down and Power-Up Timing—RESET Preceding PDN
SLES044B—November 2002
TAS5036
31
Specifications
5.4.1.2.2 Short Recovery
CONTROL SIGNAL PARAMETERS OVER RECOMMENDED OPERATING CONDITIONS (UNLESS OTHERWISE NOTED)
PARAMETER
tw(PDN)
Pulse duration, PDN active
td(R PDNR)
tp(VALID_LOW)
PDN high to reset rising edge
TEST CONDITIONS
MIN
TYP
MAX
50
ns
16 MCLKS
tp(VALID_HIGH)
UNIT
ns
4
td(VOLUME)
1
µs
5
ms
42
ms
td(R PDNR)
RESET
PDN
tw(PDN)
VALID 1–6
VOLUME 1–6
Normal
Operation
Normal
Operation
tp(VALID_HIGH)
tp(VALID_LOW)
td(VOLUME)
Figure 5–3. Power-Down and Power-Up Timing—RESET Following PDN
5.4.1.3
Error Recovery Timing—ERR_RCVRY
CONTROL SIGNAL PARAMETERS OVER RECOMMENDED OPERATING CONDITIONS (UNLESS OTHERWISE NOTED)
PARAMETER
tw(ER)
Pulse duration, ERR_RCVRY active
tp(VALID_LOW)
tp(VALID_HIGH)
Selectable for minimum or maximum
32
TAS5036
TEST CONDITIONS
MIN
TYP
MAX
5 MCLKS
UNIT
ns
6
47
µs
4
5
ms
SLES044B—November 2002
Specifications
tw(ER)
ERR_RCVRY
VALID 1–6
Normal
Operation
Normal
Operation
tp(VALID_HIGH)
tp(VALID_LOW)
Figure 5–4. Error Recovery Timing
5.4.1.4
MUTE Timing—MUTE
CONTROL SIGNAL PARAMETERS OVER RECOMMENDED OPERATING CONDITIONS (UNLESS OTHERWISE NOTED)
PARAMETER
tw(MUTE)
td(VOL)
TEST CONDITIONS
Pulse duration, PDN active
MIN
TYP
MAX
3 MCLKS
UNIT
ns
42
ms
tw(MUTE)
MUTE
VOLUME
VALID 1–6
Normal
Operation
Normal
Operation
td(VOL)
td(VOL)
Figure 5–5. Mute Timing
SLES044B—November 2002
TAS5036
33
Specifications
5.4.2 Serial Audio Port
5.4.2.1
Serial Audio Ports Slave Mode Over Recommended Operating Conditions (Unless
Otherwise Noted)
PARAMETER
MIN
f(SCLK)
tsu(SDIN)
Frequency, SCLK
SDIN setup time before SCLK rising edge
20
th(SDIN)
f(LRCLK)
SDIN hold time before SCLK rising edge
10
LRCLK frequency
32
tsu(LRCLK)
5.4.2.2
TYP
MAX
UNIT
12.288
MHz
ns
ns
48
MCLK_IN duty cycle
50%
SCLK duty cycle
50%
LRCLK duty cycle
50%
192
kHz
LRCLK setup time before SCLK rising edge
20
ns
MCLK High and Low time
20
ns
Serial Audio Ports Master Mode, Load Conditions 50 pF Over Recommended
Operating Conditions (Unless Otherwise Noted)
PARAMETER
t(MSD)
t(MLRD)
5.4.2.3
MIN
TYP
MAX
UNIT
MCLK_IN to SCLK
0
5
ns
MCLK_IN to LRCLK
0
5
ns
DSP Serial Interface Mode Over Recommended Operating Conditions (Unless
Otherwise Noted)
PARAMETER
MIN
TYP
MAX
UNIT
12.288
MHz
f(SCLK)
td(FS)
SCLK frequency
tw(FSHIGH)
tsu(SDIN)
Pulse duration, sync
SDIN and LRCLK setup time before SCLK falling edge
20
ns
th(SDIN)
SDIN and LRCLK hold time from SCLK falling edge
10
ns
Delay time, SCLK rising to Fs
ns
1/(64xfs)
SCLK duty cycle
ns
50%
SCLK
tsu(SDIN) th(SDIN)
SDIN
Figure 5–6. Right-Justified, IIS, Left-Justified Serial Protocol Timing
34
TAS5036
SLES044B—November 2002
Specifications
SCLK
tsu(LRCLK)
LRCLK
NOTE: Serial data is sampled with the rising edge of SCLK (setup time = 20 ns and hold time = 10 ns).
Figure 5–7. Right, Left, and IIS Serial Mode Timing Requirement
SCLK
LRCLK
t(MRLD)
t(MSD)
MCLK
Figure 5–8. Serial Audio Ports Master Mode Timing
SCLK
tsu(LRCLK)
LRCLK
th(LRCLK)
tw(FSHIGH)
tsu(SDIN)
th(SDIN)
SDIN
Figure 5–9. DSP Serial Port Timing
SLES044B—November 2002
TAS5036
35
Specifications
SCLK
64 SCLKS
LRCLK
tw(FSHIGH)
SDIN
16 Bits Left Channel
16 Bits Right Channel
32 Bits Unused
Figure 5–10. DSP Serial Port Expanded Timing
SCLK
tsu(SDIN) = 20 ns
th(SDIN) = 10 ns
SDIN
Figure 5–11. DSP Absolute Timing
36
TAS5036
SLES044B—November 2002
Specifications
5.4.3 Serial Control Port—I 2C Operation
5.4.3.1
Timing Characteristics for I2C Interface Signals Over Recommended Operating
Conditions (Unless Otherwise Noted)
PARAMETER
TEST CONDITIONS
STANDARD
MODE
MIN
MAX
100
FAST MODE
MIN
MAX
0
400
UNIT
fSCL
tw(H)
Frequency, SCL
0
Pulse duration, SCL high
4
0.6
µs
tw(L)
tr
Pulse duration, SCL low
4.7
1.3
µs
Rise time, SCL and SDA
1000
300
ns
tf
tsu1
Fall time, SCL and SDA
300
300
ns
th1
t(buf)
Hold time, SCL to SDA
Setup time, SDA to SCL
kHz
250
100
0
0
ns
Bus free time between stop and start condition
4.7
1.3
µs
tsu2
th2
Setup time, SCL to start condition
4.7
0.6
µs
Hold time, start condition to SCL
4
0.6
µs
tsu3
CL
Setup time, SCL to stop condition
4
Load capacitance for each bus line
tw(L)
µs
0.6
400
tw(H)
ns
tr
400
pF
tf
SCLK
tsu
th1
SDA
Figure 5–12. SCL and SDA Timing
SCLK
th2
t(buf)
tsu2
tsu3
SDA
Start
Condition
Stop
Condition
Figure 5–13. Start and Stop Conditions Timing
SLES044B—November 2002
TAS5036
37
PWM_AP_1
CSS
M_S
PWM_AM_1
Valid_1
PLL_FLT_1
DA610
DSP
ACLKX
AFSX
PLL_FLT_2
SCLK
LRCLK
Clock,
PLL
and
Serial
Data
I/F
PWM Ch.
PWM_AP_2
Signal
Processing
MCLKOUT
SDIN1
SDIN2
SDIN3
ALKX0
ALKX1
ALKX2
P1.5/IA1/TDI
P1.4/SMCLK/TCK
P1.0
MSP430 P1.1
P1.2
SDA
SCL
CSO
RESET
PDN
PWM_AM_2
PWM Ch.
Serial
Control
I/F
Reset,
Pwr Dwn
and
Status
Auto Mute
De-emphasis
Soft Volume
Error Recovery
Soft Mute
Clip Detect
PWM Ch.
SLES044B—November 2002
CLIP
MUTE
ERR_RCVY
PWM AP_3
PWM AM_3
Valid_3
PWM_AP_4
PWM_AM_4
Valid_4
PWM_AP_5
PWM_AM_5
PWM Ch.
Valid_5
PWM_AP_6
PWM Ch.
P1.3
P2.0
Valid_2
PWM Ch.
Output Control
Figure 6–1. Typical TAS5036 Application
XTAL_OUT
XTAL_IN
PWM_AM_6
Valid_6
TAS5110
PWAP
H-Bridge
PWAM
PWBM
PWBP SHUTDOWN
RESET
TAS5110
PWAP
H-Bridge
PWAM
PWBM
PWBP SHUTDOWN
RESET
TAS5110
PWAP
H-Bridge
PWAM
PWBM
PWBP SHUTDOWN
RESET
TAS5110
PWAP
H-Bridge
PWAM
PWBM
PWBP SHUTDOWN
RESET
TAS5110
PWAP
H-Bridge
PWAM
PWBM
PWBP SHUTDOWN
RESET
TAS5110
PWAP
H-Bridge
PWAM
PWBM
PWBP SHUTDOWN
RESET
Application Information
DVSS_PWM
DVSS_RCL
DVDD_PWM
DVDD_RCL
VREGC_CAP
VREGB_CAP
AVSS_PLL
VREGA_CAP
AVDD_PLL
TAS5036
PWM
Section
MCLK_IN
CLKOUT
Application Information
6
38
Power Supply
Application Information
6.1
Serial Audio Interface Clock Master and Slave Interface Configuration
6.1.1 Slave Configuration
Other Digital
Audio Sources
DA610 DSP
(Master Mode)
PCM1800
ADC
Left
Analog
OSCI
ALKR0
DOUT
Right
Analog
BCK
SYSCLK
GND
TAS5036
(Slave mode)
XTALI
OSCO
XTALO
ALKX0
SDIN1
ALKR1
ALKX1
SDIN2
ALKR2
ALKX2
SDIN3
ACLKR
ACLKX
SCLK
AFSX
LRCK
AFSR
LRCK
12.288
MHz XTAL
CLKIN
MCLKO
CLKOUT
MCLKO
NC
Figure 6–2. TAS5036 Serial Audio Port—Slave Mode Connection Diagram
6.1.2 Master Configuration
Other Digital
Audio Sources
TAS5036
(Master Mode)
DA610 DSP
PCM1800
ADC
Left
Analog
12.288
MHz XTAL
DOUT
Right
Analog
BCK
LRCK
SYSCLK
ALKR0
XTALI
XTALO
ALKX0
SDIN1
ALKR1
ALKX1
SDIN2
ALKR2
ALKX2
SDIN3
ACLKR
ACLKX
SCLK
AFSX
LRCK
AFSR
CLKIN
CLKOUT
GND
MCLKO
MCLKO
Figure 6–3. TAS5036 Serial Audio Port—Master Mode Connection Diagram
SLES044B—November 2002
TAS5036
39
Appendix A—Volume Table
Appendix A—Volume Table
VOLUME
SETTING
REGISTER VOLUME
(BIN)
GAIN dB
VOLUME
SETTING
REGISTER VOLUME
(BIN)
249
11111001
24
205
11001101
248
2
11111000
23.5
204
11001100
1.5
D7 – D0
GAIN dB
D7 – D0
247
11110111
23
203
11001011
1
246
11110110
22.5
202
11001010
0.5
245
11110101
22
201
11001001
0
244
11110100
21.5
200
11001000
–0.5
243
11110011
21
199
11000111
–1
242
11110010
20.5
198
11000110
–1.5
241
11110001
20
197
11000101
–2
240
11110000
19.5
196
11000100
–2.5
239
11101111
19
195
11000011
–3
238
11101110
18.5
194
11000010
–3.5
237
11101101
18
193
11000001
–4
236
11101100
17.5
192
11000000
–4.5
235
11101011
170
191
10111111
–5
234
11101010
16.5
190
10111110
–5.5
233
11101001
16
189
10111101
–6
232
11101000
15.5
188
10111100
–6.5
231
11100111
15
187
10111011
–7
230
11100110
14.5
186
10111010
–7.5
229
11100101
14
185
10111001
–8
228
11100100
13.5
184
10111000
–8.5
227
11100011
13
183
10110111
–9
226
11100010
12.5
182
10110110
–9.5
225
11100001
12
181
10110101
–10
224
11100000
11.5
180
10110100
–10.5
223
11011111
11
179
10110011
–11
222
11011110
10.5
178
10110010
–11.5
221
11011101
10
177
10110001
–12
220
11011100
9.5
176
10110000
–12.5
219
11011011
9
175
10101111
–13
218
11011010
8.5
174
10101110
–13.5
217
11011001
8
173
10101101
–14
216
11011000
7.5
172
10101100
–14.5
215
11010111
7
171
10101011
–15
214
11010110
6.5
170
10101010
–15.5
213
11010101
6
169
10101001
–16
212
11010100
5.5
168
10101000
–16.5
211
11010011
5
167
10100111
–17
210
11010010
4.5
166
10100110
–17.5
209
11010001
4
165
10100101
–18
208
11010000
3.5
164
10100100
–18.5
207
11001111
3
163
10100011
–19
206
11001110
2.5
162
10100010
–19.5
SLES044B—November 2002
TAS5036
41
Appendix A—Volume Table
VOLUME
SETTING
REGISTER VOLUME
(BIN)
GAIN dB
VOLUME
SETTING
D7 – D0
42
REGISTER VOLUME
(BIN)
GAIN dB
D7 – D0
161
10100001
–20
116
01110100
–42.5
160
10100000
–20.5
115
01110011
–43
159
10011111
–21
114
01110010
–43.5
158
10011110
–21.5
113
01110001
–44
157
10011101
–22
112
01110000
–44.5
156
10011100
–22.5
111
01101111
–45
155
10011011
–23
110
01101110
–45.5
154
10011010
–23.5
109
01101101
–46
153
10011001
–24
108
01101100
–46.5
152
10011000
–24.5
107
01101011
–47
151
10010111
–25
106
01101010
–47.5
150
10010110
–25.5
105
01101001
–48
149
10010101
–26
104
01101000
–48.5
148
10010100
–26.5
103
01100111
–49
147
10010011
–27
102
01100110
–49.5
146
10010010
–27.5
101
01100101
–50
145
10010001
–28
100
01100100
–50.5
144
10010000
–28.5
99
01100011
–51
–51.5
143
10001111
–29
98
01100010
142
10001110
–29.5
97
01100001
–52
141
10001101
–30
96
01100000
–52.5
140
10001100
–30.5
95
01011111
–53
139
10001011
–31
94
01011110
–53.5
138
10001010
–31.5
93
01011101
–54
137
10001001
–32
92
01011100
–54.5
136
10001000
–32.5
91
01011011
–55
135
10000111
–33
90
01011010
–55.5
134
10000110
–33.5
89
01011001
–56
133
10000101
–34
88
01011000
–56.5
132
10000100
–34.5
87
01010111
–57
131
10000011
–35
86
01010110
–57.5
130
10000010
–35.5
85
01010101
–58
129
10000001
–36
84
01010100
–58.5
128
10000000
–36.5
83
01010011
–59
–59.5
127
01111111
–37
82
01010010
126
01111110
–37.5
81
01010001
–60
125
01111101
–38
80
01010000
–60.5
124
01111100
–38.5
79
01001111
–61
123
01111011
–39
78
01001110
–61.5
122
01111010
–39.5
77
01001101
–62
121
01111001
–40
76
01001100
–62.5
120
01111000
–40.5
75
01001011
–63
119
01110111
–41
74
01001010
–63.5
118
01110110
–41.5
73
01001001
–64
117
01110101
–42
72
01001000
–64.5
TAS5036
SLES044B—November 2002
Appendix A—Volume Table
VOLUME
SETTING
REGISTER VOLUME
(BIN)
VOLUME
SETTING
REGISTER VOLUME
71
01000111
–65
36
00100100
70
69
01000110
–65.5
35
00100011
–83
01000101
–66
34
00100010
–83.5
68
01000100
–66.5
33
00100001
–84
00100000
–84.6
00011111
–85.1
GAIN dB
D7 – D0
(BIN)
GAIN dB
D7 – D0
–82.6
67
01000011
–67
32
66
01000010
–67.5
31
65
01000001
–68
30
00011110
–85.8
29
00011101
–86.1
28
00011100
–86.8
27
00011011
–87.2
26
00011010
–87.5
25
00011001
–88.4
24
00011000
–88.8
64
01000000
–68.5
63
00111111
–69
62
00111110
–69.5
61
00111101
–70
60
00111100
–70.5
59
00111011
–71
23
00010111
–89.3
58
00111010
–71.5
22
00010110
–89.8
57
00111001
–72
21
00010101
–90.3
56
00111000
–72.5
20
00010100
–90.9
55
00110111
–73
19
00010011
–91.5
54
00110110
–73.5
18
00010010
–92.1
53
00110101
–74
17
00010001
–92.8
00010000
–93.6
52
00110100
–74.5
16
51
00110011
–75
15
00001111
–94.4
–75.5
14
00001110
–95.3
13
00001101
–96.3
12
00001100
–97.5
11
00001011
–98.8
10
00001010
–100.4
9
00001001
–102.4
8
00001000
–104.9
7
00000111
–108.4
6
00000110
–114.4
50
00110010
49
00110001
–76
48
00110000
–76.6
47
00101111
–77
46
00101110
–77.5
45
00101101
–78
44
00101100
–78.5
43
00101011
–79
42
00101010
–79.6
5
00000101
MUTE
41
00101001
–80.1
4
00000100
MUTE
40
00101000
–80.6
3
00000011
MUTE
39
00100111
–81.1
2
00000010
MUTE
38
00100110
–81.5
1
00000001
MUTE
37
00100101
–82.1
0
00000000
MUTE
SLES044B—November 2002
TAS5036
43
PACKAGE OPTION ADDENDUM
www.ti.com
6-Dec-2006
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TAS5036IPFC
NRND
TQFP
PFC
80
119
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-4-260C-72 HR
TAS5036IPFCR
NRND
TQFP
PFC
80
1000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-4-260C-72 HR
TAS5036PFC
OBSOLETE
TQFP
PFC
80
TBD
Call TI
Call TI
TAS5036PFCR
OBSOLETE
TQFP
PFC
80
TBD
Call TI
Call TI
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
MECHANICAL DATA
MTQF009A – OCTOBER 1994 – REVISED DECEMBER 1996
PFC (S-PQFP-G80)
PLASTIC QUAD FLATPACK
0,27
0,17
0,50
60
0,08 M
41
61
40
80
21
1
0,13 NOM
20
Gage Plane
9,50 TYP
12,20
SQ
11,80
0,25
14,20
SQ
13,80
0,05 MIN
0°– 7°
0,75
0,45
1,05
0,95
Seating Plane
0,08
1,20 MAX
4073177 / B 11/96
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-026
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265